|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ300A. - Working frequency: 0Hz ~ 300KHz. - Test frequency range is wide. Frequency range: 0 ~ 300KHz. See the pictures below for details. ... more- The NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ100A. - Working frequency: 0Hz ~ 100KHz. - Test frequency range is wide. Frequency range: 0 ~ 100KHz. See the pictures below for details. ... moreThe NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
$40.00 Shipping Condition: New Location: Japan ★ Parallel (Lp・Cp・Rp)/serial (Ls・Cs・Rs) mode switching. ★Test frequency: 100/120/1k/10k/100kHz (0.5Vrms, sine wave). ・Open interval of the tip of the ... moreclip: about 6mm. ★Dual display: main 20000/sub 2000 count.
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ100A. - Working frequency: 0Hz ~ 100KHz. - Test frequency range is wide. Frequency range: 0 ~ 100KHz. See the pictures below for details. ... moreThe NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
Free Shipping Condition: New Location: China Product Details:.
Buy It Now
Free Shipping Condition: New Location: China Sampling rate: 1M. - Impedance test range: 1KOhm to 10MOhm. - Programmable frequency scanning function and seriel I2C interface. - 1 x Module. - Internal ... moretemperature sensor. Usually it cost about 35USD-50USD.
Buy It Now
Free Shipping Condition: New Location: Canada Power Quality Analyzer. Signal source output impedance:100Ω, ±1% @1kHz. Trigger Mode: INT, MAN, EXT, BUS. Test Frequency Range: 20Hz-10MHz. Short Circuit ... moreStrip. Rdc Test Current Range: 0mA— 20mA. Power Quality Analyzers.
Buy It Now
$250.00 Shipping Condition: New Location: 龙华区, China Piezoelectric ceramic, ultrasonic transducer devices and so on. ZX70A/ZX80A series provides a super solution for frequency scan and. ● ZX70AX-1M: Impedance ... moreAnalyzer, Maximum frequency up to 1MHz, LCR test function.
Buy It Now
Free Shipping Condition: New Location: United States Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
Free Shipping Condition: New Location: United States Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
Free Shipping Condition: New Location: Topeka, United States DE-5000 Handheld LCR Meter/w SMD Probe and Alligator cable I hope to sell the good hand held LCR Met er DE-5000 with the SMD probe adapter and home-made ... morealligator cable. The detailed info about this LCR Met er.You can easily google the word"DER EE" website,though the fundamental features are like this. Auto L.C.R. check• 100/ 120/ 1k/ 10k/ 100k Hz test frequency• 20.000/ 2,000 counts display• Backlight blue• Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement• Relative mode• Series/ Parallel modes• Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% This time.I sell DE-5000 itself and SMD probe adapter and home-made alligator cable only,not included 9V AC adapter and IR-USB adapter. If you hope to get IR-USB adapter and software.Plz mail me,I will also up to the auction) I hope to sell them as is.But I will make an effort for your convenience. I give you CD(English manual.Software,how to mke up the kelvin cable,how to make up 7MHz BPF etc)And If you rather hope to use the kelvin clip.Instead of this SMD clip,I will give you how to modify it.in CD I added the several pics and memo) General Specifications) Auto L.C.R. check*100/ 120/ 1k/ 10k/ 100k Hz test frequency*20.000/ 2,000 counts display*Backlight blue*Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement*Relative mode*Series/ Parallel modes*Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% Ohm* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm(parallel/ series mode) DCR* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm*Capacitance* Range)200pF/2000pF/20nF/200nF/2000nF/20uF/200uF/2000uF/20mF(parallel/ series mode) Inductance* Range)20uH/200uH/2000uH/20mH/200mH/2000mH/20H/200H/2000H(parallel/ series mode) Low battery indicator Yes*Over r
Buy It Now
$250.00 Shipping Condition: New Location: 龙华区, China ● ZX70AX-500k: Impedance Analyzer, Maximum frequency to 500kHz, LCR test function. piezoelectric ceramic, ultrasonic transducer devices and so on. ZX70A/ZX80A ... moreseries provides a super solution for frequency scan and.
Buy It Now
$165.00 Shipping Condition: Seller refurbished Location: Newbury Park, United States Both floating and grounded devices can be tested. 5 Hz to 13 MHz variable frequency. Rohde Schwarz FSW26 2 Hz - 26.5 GHz Signal Spectrum Analyzer, LOADED ... more& R&S CAL'D. Keysight N9914A 30kHz - 6.5GHz Analyzer w/ OPTS 112/210/211/233/235 - CAL'D.
Buy It Now
Free Shipping Condition: New Location: China Bench Top High-accuracy 0.2% LCR Meter& Component Parameter Tester 10kHz TH2811D LCR meter is our newly developed successor instrument for low frequency ... morecomponent measurement. TH2811D with its latest measurement technologies. Large character LCD display. Surface mount techniques, easy of use and excellent appearance can be used for quality control on production line. Incoming inspection of components and automatic test system. Features: ■ Large character LCD display with backlight ■ Easy operation with strong functions ■ SMT surface mount technic ■ Fast measurement speed(80mS) ■ Good Readout stability ■ 2 signal source output impedance:30Ω. 100Ω Specifications: Measurement parameter L-Q. C-D, R-Q, Z︱ Q Basic accuracy 0.2% Equivalents circuit series. Parallel Rang model auto. Hold Trigger model internal Measurement speed fast 12. Med, 5.1, slow, 2.5 times/second Calibration function open/short sweep correction Measurement terminal 5-termainal Display model direct Display large character LCD with backlight Signal frequency 100Hz. 120Hz, 1KHz, 10KHz Out impedance 30Ω. 100Ω Test level 0.1Vrms. 0.3Vrms, 1Vrms Power supply 99V-121V. 198V-242V.47.5Hz-63-Hz Power consumption ≤2 VA Dimensions(W X H X D) 270mm x 139mm x 290mm Net weight 3.7Kg Measurement Display Range |Z|. R: 0.1mΩ- 99.99MΩ C 100Hz/120Hz 1pF- 99999μ F 1KHz 0.1pF- 9999.9μ F 10KHz 0.01pF- 999.99μ F L 100Hz/120Hz 1μH- 99999H 1KHz 0.1μH- 9999.9H 10KHz 0.01μH- 999.99H D 0.0001- 9.999 Q 0.0001- 9999 Δ% 999.99% 999.99% Display Display Mode Direct Display Large character LCD with backlight Display digits Primary and secondary display:5 digits Accessories: TH26001A 4 terminal test fixture TH26004-1 4 terminal Kelvin test clip leads Th26010 Gilded shorting plate Manual Power cord Note: we'll ship this item via express mail service to USA. Canada, Australia, New Zealand, Ireland, Austria, Belgium, Denmark, Germany, France, Finland, Italy, Luxemburg, Malta, Norway, Sweden, Swiss, UK, Spain, Japan, Korea,Thailand, Malaysia, Indonesia, Philippine,
Buy It Now
$4.99 Shipping Condition: New Location: China DT71 provides a perfect solution for debugging and maintenance of complex electronic systems and the classification and detection of discrete chip components. ... moreIt is compact and pocket size for easy taking.
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ300A. - Working frequency: 0Hz ~ 300KHz. - Test frequency range is wide. Frequency range: 0 ~ 300KHz. See the pictures below for details. ... more- The NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
Free Shipping Condition: New Location: Houston, United States 100 / 120 / 1k / 10k / 100k Hz test frequency 2. Dual 19999/1999 display 3. Backlight 4. Ls / Lp / Cs / Cp / Rs / Rp / dissipation factor (D) / quality ... morefactor (Q) /phase angle/ ESR LCR auto selection 5.
Buy It Now
Free Shipping Condition: New Location: United States
Buy It Now
Free Shipping Condition: New Location: Canada DE-5000 Handheld LCR Meter/w SMD Probe and Alligator cable I hope to sell the good hand held LCR Met er DE-5000 with the SMD probe adapter and home-made ... morealligator cable. The detailed info about this LCR Met er.You can easily google the word"DER EE" website,though the fundamental features are like this. Auto L.C.R. check• 100/ 120/ 1k/ 10k/ 100k Hz test frequency• 20.000/ 2,000 counts display• Backlight blue• Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement• Relative mode• Series/ Parallel modes• Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% This time.I sell DE-5000 itself and SMD probe adapter and home-made alligator cable only,not included 9V AC adapter and IR-USB adapter. If you hope to get IR-USB adapter and software.Plz mail me,I will also up to the auction) I hope to sell them as is.But I will make an effort for your convenience. I give you CD(English manual.Software,how to mke up the kelvin cable,how to make up 7MHz BPF etc)And If you rather hope to use the kelvin clip.Instead of this SMD clip,I will give you how to modify it.in CD I added the several pics and memo) General Specifications) Auto L.C.R. check*100/ 120/ 1k/ 10k/ 100k Hz test frequency*20.000/ 2,000 counts display*Backlight blue*Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement*Relative mode*Series/ Parallel modes*Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% Ohm* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm(parallel/ series mode) DCR* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm*Capacitance* Range)200pF/2000pF/20nF/200nF/2000nF/20uF/200uF/2000uF/20mF(parallel/ series mode) Inductance* Range)20uH/200uH/2000uH/20mH/200mH/2000mH/20H/200H/2000H(parallel/ series mode) Low battery indicator Yes*Over r
Buy It Now
$50.00 Shipping Condition: New Location: Romania A linear and logarithmic sweep function is also provided to characterize components over any range of frequencies from 20Hz to 300KHz. THEY ARE CORRECT ... moreBEFORE BUYING.
Buy It Now
$300.00 Shipping Condition: Used Location: South Korea You are Bidding on a used HP 43961A RF Impedance Test Kit Set Returns If you receive your item. And it is significantly different than described, please ... morecontact us, and we will arrange a full refund or product exchange. We must receive the returned item(s) within(10 days) of original delivery. Items should be returned in the original packaging whenever possible. If this is not possible. The item should be packed to meet the carrier's insurable packaging specifications. Typically this requires a sturdy cardboard box with at least 2" of padding on all 6 sides. AS IS Items that are sold"AS IS" are not eligible for refunds or exchanges of any kind. As long as the item shipped is the correct item listed. Of course. Feedback We are happy to leave positive feedback as soon as your on-time payment clears. And we appreciate your positive feedback if your transaction is satisfactory. Remember, we are always willing to work with you on any problems you may experience, so please contact us before leaving negative feedback. If you are unfamiliar with the feedback system, please check out eBay's. Non-Paying Bidders Items that are not paid for within one week(7 days) of auction close with no contact or payment arrangement will be added back into our inventory. And an eBay non-paying-bidder claim will be filed. Sales Tax We charge sales tax on all of our customers in CA unless proper exclusion documentation is provided California Resale Certificate. Local Pickup Local pickup is welcome and is actually our preferred method of getting items to customers. Pickup hours are Monday-Friday 8am-4pm PST. Please email or call ahead for an appointment. Our physical address is: WastErasers: 1710 Little Orchard St: San Jose. CA 95125: United States Privacy Policy Any personal information a customer provides us is used STRICTLY for internal purposes. We will not. Under any circumstances, divulge a customer's personal information to any person or company that is not directly involved in the daily operations of WastEr
Buy It Now
$230.00 Shipping Condition: Used Location: China In these bad economic times. Get more“bang” for your money with tested, working and calibrated test equipment from AAA Equipment Resources INC. I AM A ... moreWELL KNOWN SELLER AND BUYER OF ALL WORKING TEST EQUIPMENT.WE OUR ONE OF EBAYS TOP SELLERS OF TESTED. WORKING, AND CALIBRATED TEST EQUIPTMENT FOR OVER ELEVEN YEARS. I AM A MAN OF MY WORD. OUR GOAL IS TO EXCEED CUSTOMER’S EXPECTATIONS. YOU ARE BUYING A PROFESSIONALLY TESTED AND CHECKED OUT AS FULLY FUNCTIONAL, HP- AGILENT 4192A 5 Hz to 13 MHz LF IMPEDANCE ANALYZER WITH MANUAL! It was just calibrated. Date Due 05/07/14. The unit is in good to great cosmetic condition. It may have a small scratch here or there. All buttons, knobs, and switches are good and intact. The serial# is 2045J00282. Will works with 120& 240 voltage. We always re-check the item before we ship it. This makes sure the item is working when it left my shop. No options are marked. WE WILL RE-CALIBRATED THE UNIT BEFORE SHIPPING AND A NIST TRACEABLE CALIBRATION CERTIFICATE. WILL BE PROVIDED AFTER ITEM IS RECEIVED AND IS ACCEPTED AS WORKING WITH IN SPECS. WE WILL MAIL OUT THE CERTIFICATE. THE RE-CALIBRATION DELAYS THE SHIPPING TIME THREE(3) DAYS. HP 4192A LF impedance analyzer performs both network analysis and impedance analysis on such devices such as telecommunication filters. Audio/video electronic circuits, and basic electronic components. Both floating and grounded devices can be tested. Features& Specifications* 5 Hz to 13 MHz variable frequency* Swept measurement capability* Gain-phase measurements: amplitude. Phase, group delay* Floating or grounded devices* Impedance measurement: |Z|, |Y|, Theta, R, X, G, B, L, C, D, Q, Delta, Delta% GPIB. For more information and Specs: I HAVE THE HP- AGILENT 4191A RF IMPEDANCE ANALYZER WITH THE HP- AGILENT 16093A BINDING POST FIXTURE AND MANUAL. HP- AGILENT 4195A 10 Hz to 500 MHz NETWORK/ SPECTRUM ANALYZER WITH CABLES AND MANUALS, HP- AGILENT 15709A 100 Hz- 25 MHz HIGH IMPEDANCE INTERFACE, AGILENT- HP 4395A 10 Hz- 500 MHz NE
Buy It Now
Free Shipping Condition: New Location: Canada Power Quality Analyzer. Signal Source Output Impedance:100Ω, ±1% @1kHz. Test Frequency Range: 20Hz-10MHz. Short Circuit Strip. Power Quality Analyzers. ... moreNew products typically carry a 1 Year Warranty.
Buy It Now
$300.00 Shipping Condition: Used Location: China We have 4 units Used WAYNE KERR WK 6500B ,Seven models of 20Hz~5MHz, 10MHz, 15MHz, 20MHz, 30MHz, 50MHz and 120MHz. The default is the price of 30MHz with ... morea fixture. We will do our best and help you provide the solution.
Buy It Now
$5.00 Shipping Condition: New Location: China Product model: NJ200A. - Working frequency: 0Hz ~ 200KHz. - Test frequency range is wide. Frequency range: 0 ~ 200KHz. See the pictures below for details. ... more- The NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
Free Shipping Condition: New Location: China Comparator separation (5), alarm function. Support SCPI communication protocol. Test level 10 ～ 2000 mv.
Buy It Now
$225.00 Shipping Condition: New Location: 龙华区, China Note: both AC 110V and 220V versions are available. We'll ship this item via express mail service to USA. Canada, Australia, New Zealand, Ireland, ... moreAustria, Belgium, Denmark, Germany, France, Finland, Luxemburg, Malta, Norway, Sweden, Swiss, Spain, Italy, UK, Japan, Korea, Thailand, Malaysia, Indonesia, Philippine, Singapore. Clients from other countries pls contact with us in advance to confirm the different shipping charges before you bid. Features: 192 x 64 dot matrix LCD display. Higher measurement stability and accuracy. 30Ω/100Ω selectable signal source output impedance. 50Hz- 200 kHz(21 typical measuring frequencies) User-friendly interface and easy operation. Direct reading. Absolute deviation and relative deviation display. Packing list: Power cord x1; Test lead x1; Fuse x2. Specifications: Parameter Frequency Measuring range L 50Hz- 800Hz 1uH- 9999H 1kHz 0.1uH- 999.9H 10kHz- 200kHz 0.01uH- 99.99H C 50Hz- 800Hz 1pF- 19999uF 1kHz 0.1pF- 1999.9uF 10kHz- 200kHz 0.01pF- 19.99uF R 0.001Ω- 39.999MΩ D 0.0000- 9999 Q 0.0000- 9999 Measuring parameters Cs-D. Cp-D, Ls-Q, Lp-Q, Z-D, R-Q, total 6 parameter groups. Basic Accuracy 0.1% Measuring Frequency 50/60/80/100/120/200/400/500/800/1k/2k/4k/5k/80k/10k/ 20k/25k/40k/50k/100kHz/200KHz Display Range Z|. R:0.0001 Ω- 99999MΩ C: 0.001 pF- 99999mF L: 0.001 µH- 99.999kH Q: 0.0001- 99999 D: 0.0001- 99999 Δ% 99.999% 99.999% Source Resistance 30Ω. 100Ω Range Automatic. Manual, and nominal, 5 ranges Max Reading 5 digital. Principle parameter: 99999; sub parameter:99999; monitor parameter; 99999. Signal Level 0.1V. 0.3V, 1V. Measuring Speed Slow: 2 times/second. Med:5 times/second, Fast:10times/second Component Sorting 4 Bins: NG/P1/P2/P3 Clear Function Open/ short circuit. Clear Zeroing Equivalent Circuit Series and parallel Display 192 x 64 dot-matrix LCD Power Supply 220V AC Dimension& Weight 350mm(width)x110mm(height)x320mm(depth) 7.4kg
Buy It Now
$3.00 Shipping Condition: New Location: China Xp: equivalent shunt reactance. - Xs: equivalent series reactance. - Lp: inductor in parallel mode. - Ls: series inductor model. - ESR: equivalent series ... moreresistance. - Cp: capacitor in parallel mode.
Buy It Now
Free Shipping Condition: New Location: China Model: ET4410. Model: ET4401. 1 × LCR digital bridge. Signal source output impedance: 30Ω、100Ω. ◆Support SCPI communication protocol. Internal bias: 0-1500mV ... moreadjustable, at a step of 1mV. ◆Test level 100mV ～ 2000 mV.
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ300S. Test frequency range is wide. Frequency range: 50Hz~300KHz. The frequency point is continuously adjustable (except for NJ100S). ... more- Working frequency: 50Hz~300KHz. See the pictures below for details.
Buy It Now
Free Shipping Condition: New Location: China ■ Interface function, timing, trigger delay, etc. are more complete. Basic Accuracy 0.1%. Impedance evaluation of printed circuit boards, relays, switches, ... morecables, batteries, etc. Trigger mode Internal, External, Manual, Bus.
Buy It Now
$3.20 Shipping Condition: Neu Location: China DT71 provides a perfect solution for debugging and maintenance of complex electronic systems and the classification and detection of discrete chip components. ... moreIt is compact and pocket size for easy taking.
Buy It Now
Free Shipping Condition: New Location: United States DE-5000 Handheld LCR Meter/w SMD Probe and Alligator cable I hope to sell the good hand held LCR Met er DE-5000 with the SMD probe adapter and home-made ... morealligator cable. The detailed info about this LCR Met er.You can easily google the word"DER EE" website,though the fundamental features are like this. Auto L.C.R. check• 100/ 120/ 1k/ 10k/ 100k Hz test frequency• 20.000/ 2,000 counts display• Backlight blue• Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement• Relative mode• Series/ Parallel modes• Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% This time.I sell DE-5000 itself and SMD probe adapter and home-made alligator cable only,not included 9V AC adapter and IR-USB adapter. If you hope to get IR-USB adapter and software.Plz mail me,I will also up to the auction) I hope to sell them as is.But I will make an effort for your convenience. I give you CD(English manual.Software,how to mke up the kelvin cable,how to make up 7MHz BPF etc)And If you rather hope to use the kelvin clip.Instead of this SMD clip,I will give you how to modify it.in CD I added the several pics and memo) General Specifications) Auto L.C.R. check*100/ 120/ 1k/ 10k/ 100k Hz test frequency*20.000/ 2,000 counts display*Backlight blue*Ls/ Lp/ Cs/ Cp/ Rs/ Rp/ DCR with D/ Q/ θ/ ESR measurement*Relative mode*Series/ Parallel modes*Components sorting function*Selectable tolerance ±0.25% ±0.5% ±1% ±2% ±5% ±10% ±20% 20% +80% Ohm* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm(parallel/ series mode) DCR* Range)20ohm/200ohm/2kohm/20kohm/200kohm/2Mohm/20Mohm/200Mohm*Capacitance* Range)200pF/2000pF/20nF/200nF/2000nF/20uF/200uF/2000uF/20mF(parallel/ series mode) Inductance* Range)20uH/200uH/2000uH/20mH/200mH/2000mH/20H/200H/2000H(parallel/ series mode) Low battery indicator Yes*Over r
Buy It Now
Free Shipping Condition: New Location: China UNI-T UT612 USB Interface Auto Range LCR Meter Inductance Freq Tester Auto Off Features: Display Count: 20000 D/Q Display Count: 2000 D/Q Resolution: ... more0.001 Auto Range: √ Real-Time Display Test Frequency: √ Measurement Mode: Series/Parallel Auto Power Off: √ Low Battery Indication: ≤6.8V Data Hold: √ Relative Mode: √ USB Interface: √ USB Interface/PC Data Records: 60000 LCD Backlight: √ Analogue Bar Graph: 26 Deviation Ratio Measurement: √ Comparsion Function: √ Calibration Function: √ Output Impedance: 120Ω Auto LCR Smart Check and Measurement: √ Specification: Model: UT612 Inductance(H) 20uH～2000H ±(0.5%+5) Capacitance(F) 200pF～20mF ±(0.5%+5) Resistance(Ω) 20Ω～200MΩ ±(0.3%+5) Test Frequency(Hz) 100Hz/120Hz/1KHz/10KHz/100KHz Operational Voltage: 0.6Vrms Test Parameters: L/C/R/DCR/Q/D/θ/ESR General Characteristic: Product Net Weight: 374g Product Size: 96* 193* 47mm Power: 9V Battery（6F22) or USB(not included) LCD Size: 40* 63mm Product Colour: Red and Grey Package Size: 29* 22.5* 7cm/ 11.4* 8.8*2.7in Package Weight: 1157g/ 2.5lb Package List: H12312 1* UNI-T UT612 LCR Meter 1* SMD Test Clamp 1* USB Interface Cable 1* Multi-Purpose Socket 1* PC Software CD 1* English Manual On Jan-19-15 at 07:56:32 PST. Seller added the following information:
Buy It Now
$175.00 Shipping Condition: Seller refurbished Location: Culver City, United States Agilent MSO6104A 1 GHZ 4 Channel Mixed Signal Oscilloscope - WITH ALL OPTIONS! Agilent E5404A Pro Series Soft Touch Connectorless Logic Analyzer Probe. ... moreNot a problem. If you don't see it in the pictures, it is not included.
Buy It Now
$225.00 Shipping Condition: New Location: 龙华区, China Bench Top High-accuracy 0.2% LCR Meter& Component Parameter Tester 10kHz TH2811D LCR meter is our newly developed successor instrument for low frequency ... morecomponent measurement. TH2811D with its latest measurement technologies. Large character LCD display. Surface mount techniques, easy of use and excellent appearance can be used for quality control on production line. Incoming inspection of components and automatic test system. Features: ■ Large character LCD display with backlight ■ Easy operation with strong functions ■ SMT surface mount technic ■ Fast measurement speed(80mS) ■ Good Readout stability ■ 2 signal source output impedance:30Ω. 100Ω Specifications: Measurement parameter L-Q. C-D, R-Q, Z︱ Q Basic accuracy 0.2% Equivalents circuit series. Parallel Rang model auto. Hold Trigger model internal Measurement speed fast 12. Med, 5.1, slow, 2.5 times/second Calibration function open/short sweep correction Measurement terminal 5-termainal Display model direct Display large character LCD with backlight Signal frequency 100Hz. 120Hz, 1KHz, 10KHz Out impedance 30Ω. 100Ω Test level 0.1Vrms. 0.3Vrms, 1Vrms Power supply 99V-121V. 198V-242V.47.5Hz-63-Hz Power consumption ≤2 VA Dimensions(W X H X D) 270mm x 139mm x 290mm Net weight 3.7Kg Measurement Display Range |Z|. R: 0.1mΩ- 99.99MΩ C 100Hz/120Hz 1pF- 99999μ F 1KHz 0.1pF- 9999.9μ F 10KHz 0.01pF- 999.99μ F L 100Hz/120Hz 1μH- 99999H 1KHz 0.1μH- 9999.9H 10KHz 0.01μH- 999.99H D 0.0001- 9.999 Q 0.0001- 9999 Δ% 999.99% 999.99% Display Display Mode Direct Display Large character LCD with backlight Display digits Primary and secondary display:5 digits Accessories: TH26001A 4 terminal test fixture TH26004-1 4 terminal Kelvin test clip leads Th26010 Gilded shorting plate Manual Power cord Note: we'll ship this item via express mail service to USA. Canada, Australia, New Zealand, Ireland, Austria, Belgium, Denmark, Germany, France, Finland, Italy, Luxemburg, Malta, Norway, Sweden, Swiss, UK, Spain, Japan, Korea,Thailand, Malaysia, Indonesia, Philippine,
Buy It Now
$3.00 Shipping Condition: New Location: China Product model: NJ200S. Test frequency range is wide. Frequency range: 50Hz~200KHz. The frequency point is continuously adjustable (except for NJ100S). ... more- Working frequency: 50Hz~200KHz. See the pictures below for details.
Buy It Now
$14.58 Shipping Condition: New Location: Canada
Buy It Now
$4.99 Shipping Condition: New Location: China F/VHF/UHF Impedance SWR Antenna Analyzer For Ham Radio Hobbists INTRODUCTION: AW07A antenna analyzer is a compact battery powered RF impedance analyzer. ... moreIt can test the SWR status of your antenna. Measure the impedance and reactance component and help you to solve antenna problems. This unit combines six basic parts: a variable oscillator. Frequency counter, independent oscillator, 50 ohm RF bridge detector. An A-D converter, and microcontroller. This compact product was built to feed the need for the solid construction and field test. The operating frequency range of this unit goes from HF. And extends up to 490MHz. It is specially designed for analyzing 50ohm antenna system. It measures RF impedances from a few ohms to several hundred ohms. The AW07A is also an L/C meter. Measuring the values of capacitors and inductors. Additionally. It could be a non-precision signal source and frequency counter. With a built-in RF strength meter. It tests the RF field strength near your antenna system, and it’s very useful when you need to know the RF interference status around your station. The AW07A also functions as a non-precision signal source and frequency counter. The operating frequency range of this unit extends from 1.5 to 71 MHz in six overlapping bands. And includes SWR measurements on 85-185MHz, 300-490 MHz. FEATURES LIST: 1. SINGNAL SOURCE 2. CAPACITANCE METER 3. INDUCTANCE METER 4. SHOW REACTANCE VALUE 5. SHOW IMPEDANCE VALUE 6. SWR VALUE FROM 1.1 TO 9.99 7. RF STRENGTH METER 8. FREQUENCY COUNTER. SPECIFICATIONS: 1. Band Coverage: 160m. 80m, 40m, 20/30m,10/15m, 6m, 2m, 70cm 2. RF Output Level: 2Vpp 3. SWR Range: 1~9.9 4. Impedance Range: 10~500ohm 5. Reactance Range: 6. L measurement Range: 7. C measurement Range: 8. External Power: DC 10.8~12V 9. Battery: 8* AA Alkaline Battery 10. Power Consumption: 11. Weight: 0.6 kg 12. Size: 155(W)×100(D)×55(H) Package: one Antenna Analyzer one power cable About Shipping If you intend to bid for more than 1 item. Then we can ship them together. The total ship
Buy It Now
Free Shipping Condition: New Location: China 1 × LCR digital bridge. ◆Comparator separation (5), alarm function. Signal source output impedance: 30Ω、100Ω. It'll take you one minute only. ◆Support ... moreSCPI communication protocol. Internal bias: 0-1500mV adjustable, at a step of 1mV.
Buy It Now
$189.64 Shipping Condition: Used Location: Irvine, United States NOTE: This is the 'A' version that grandfathered the privilegeto retroactively upgrade to Option 001 (advanced DC bias beyond the 1.5V and 2V set points). ... moreI'll do everything within my abilities (as an electronics hobbyist) to make sure your intended usage is well taken care of.
Buy It Now
$42.50 Shipping Condition: Used Location: Newbury Park, United States It is typically furnished with the 4294A. Excellent High Q/Low D accuracy enables analysis of low-loss components. Agilent 4294A Features Agilent Keysight ... moreU2002A 10MHz - 26.5GHz (-60 to +20dBm) USB Power Sensor - CAL'D.
Buy It Now
Free Shipping Condition: New Location: China The basic accuracy of 0.05% and good test stability can compare favourably with those high-end models. ■ Selectable 30Ω/100Ω signal source impedance. ... moreSignal Source Output Impedance Selectable 30Ω, 100Ω, ±1% @1kHz.
Buy It Now
$45.95 Shipping Condition: New Location: Elgin, United States The 880 includes a 120 V AC adapter. For a 230 V AC adapter, order model 880-220 V.
Buy It Now
$0.49 Shipping Condition: New Location: United States Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
Free Shipping Condition: New Location: China ◈ Circuit Tester. ◈ Fuel Injector Tester. Audio Impedance Tester x 1;. Low battery indication. Data Hold Indication: H symbol appears on the display. ... moreConvenient protable battery operation. Display: LCD 3 1/2 digits (2000 counts), with unit.
Buy It Now
$44.33 Shipping Condition: Used Location: Jupiter, United States GR / GenRad / QuadTech / IET 1689 Precision RLC Digibridge. The item is in good condition, tested and working. Includes test lead adapter. Test Frequencies: ... moreOver 500 programmable test frequencies (12Hz to 100kHz) 0.01% Accuracy.
Buy It Now
$0.49 Shipping Condition: New Location: United States Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
$225.00 Shipping Condition: New Location: 龙华区, China Interface RS-232C, HANDLER,(optional) RS-232C, HANDLER. equivalent circuit Series, parallel. Correction function Open circuit, short circuit. 50 Hz~100 ... morekHz,A total of 34 typical test frequencies. the product can provide stable 5 bit resolution test.
Buy It Now
Free Shipping Condition: New Location: China Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
Free Shipping Condition: New Location: United States Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. ... moreThe larger the value, the closer the capacitor is to scrapping!
Buy It Now
$300.00 Shipping Condition: Used Location: 三重區, Taiwan ITEM FOR SALE Agilent HP 4291B 1MHz-1.8GHz RF Impedance/Material Analyzer Option 001. There are no additional accessories. Manuals or power cords included ... morewith this unit other than what is stated above or shown in the pictures. The item you are bidding on is the actual item pictured. If you need additional pictures. Please feel free to ask. PAYMENT Paypal is the preferred Payment method. For International buyers. Please contact us for payment method. WARRANTY This item comes with a 30 Day warranty and 7 Days ROR. If you have any questions regarding this please feel free to call us or email us at any time. All items are fully tested and guaranteed working. SHIPPING The prices shown are our quoted values for shipping. For a custom shipping quote. Please feel free to call us. We can also ship on your Fedex account and a small fee will be charged for boxing/packing the equipment. Powered by The free listing tool. List your items fast and easy and manage your active items.
Buy It Now
$280.00 Shipping Condition: New Location: 龙华区, China Balance Test L, R, Z, DCR. Impedance evaluation of printed circuit boards, relays, switches, cables, batteries, etc. Zero Clearing Open, Short, Load. ... moreBasic Accuracy 0.1%. ■ Screen capture function. Equivalent Circuit Series, Parallel.
Buy It Now
Free Shipping Condition: New Location: Japan Manufacturer model number IM3570. Output impedance Normal mode: 100 Ω, low impedance high precision mode: 10 Ω. Accessories Power cord x1, instruction ... moremanual x1, CD-R (communication instruction manual, sample software) x1.
Buy It Now
Free Shipping Condition: New Location: Canada The basic accuracy of 0.05% and good test stability can compare favourably with those high-end models. Being equipped with. Test Frequency: 20Hz -200kHz, ... more15025 points. Test Fixture. RDC Test Signal Level: 1V.
Buy It Now
$330.00 Shipping Condition: Used Location: China We send the products randomly. We will do our best and help you provide the solution.
Buy It Now
Free Shipping Condition: New Location: China The basic accuracy of 0.05% and good test stability can compare favourably with those high-end models. 200kHz test frequenc. 10mVrms-2.0Vrms programmable ... moresignal level, built-in 0 - ± 5V/50mA bias source.
Buy It Now
$950.00 Shipping Condition: Used Location: South Korea
Buy It Now
$3.99 Shipping Condition: New Location: China Product model: NJ200A. - Working frequency: 0Hz ~ 200KHz. - Test frequency range is wide. Frequency range: 0 ~ 200KHz. See the pictures below for details. ... more- The NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design.
Buy It Now
Free Shipping Condition: New Location: China The basic accuracy of 0.05% and good test stability can compare favourably with those high-end models. 100kHz test frequency. Test Signal Frequency 50Hz-100kHz, ... morecontinuously. ■ 10mVrms-2.0Vrms programmable signal level, built-in 0 - ± 5V/50mA bias source.
|
|
|
 |