|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: New Location: Brentwood, United States Double Threaded LH/RH 1" x 8tpi for use on both inboard and outboard. 1" X 8TPI RH/LH Double Threaded for turning both inboard and outboard. Flat spots ... morecut on back spigot for easy removal from lathe. This is a well made, heavy faceplate.
Buy It Now
$10.40 Shipping Condition: New Location: Lake Zurich, United States This is an all aluminum face plate for wood lathe spindles & similar applications. Your choice of thread hole listed below. 1/2" x 20 threads left hand. ... more1" x 8 threads left hand. 1-1/8" x 7 threads left hand.
Buy It Now
$10.40 Shipping Condition: New Location: Lake Zurich, United States This is an all aluminum face plate for wood lathe spindles & similar applications. Your choice of hole listed below. If you need another size not listed ... moreI may be able to get the tap. 30Mm bored hole.
Buy It Now
$17.05 Shipping Condition: New Location: Lake Zurich, United States This is an all aluminum face plate for wood lathe spindles & similar applications. Your choice of hole listed below. If you need another size not listed ... moreI may be able to get the tap. 3/8" x 16 threads right hand.
Buy It Now
$17.00 Shipping Condition: New Location: Lake Zurich, United States I can not make smaller hole sizes as the hole is already threaded 3/4" x 16 RH.
Buy It Now
$10.40 Shipping Condition: New Location: Lake Zurich, United States This is an all aluminum face plate for wood lathe spindles & similar applications. Your choice of hole listed below. If you need another size not listed ... moreI may be able to get the tap. M30 bored hole.
Buy It Now
Free Shipping Condition: New Location: Bellingham, United States SB1126 18" x 40" Variable-Speed Wood Lathe. South Bend is proud to announce the introduction of an amazing, heavy-duty wood lathe designed for professional ... moreuse. Spindle taper: MT#2. Swing over bed: 18", 35-1/2" with bed extension.
Buy It Now
Free Shipping Condition: New Location: Bellingham, United States G0838 16" x 24" Variable-Speed Wood Lathe. The complete and easy-to-read manual makes it easier to assemble and maintain your lathe. With a 2 HP 3-phase ... moremotor using a VFD inverter to operate on single-phase 220V power, this lathe gives you the extra torque needed for turning hard woods at really low speeds.
Buy It Now
Condition: Used Location: Blanco, United States If you've ever wanted to own a high quality C.N.C lathe with huge capacity, this is your chance. You won't find another one at a better price! If you ... morewant to just turn a cylinder, for hand work, this is easy to do, and will ease you into the programing aspect.
Buy It Now
$399.00 Shipping Condition: Used Location: Enfield, United States Motor: Induction, 1725 RPM, 3HP, 220V, 60Hz. Wall Thickness of legs on the Revo 24|36 is 80% heavier compared to the Revo 18|36. Steel is the preferred ... morematerial due to its well-known longevity & strength.
|
|
|
|
Delta 1460 Lathe Outboard Faceplate Left-hand threads DDL-179
Used part that came with a Delta 1460 Lathe. No cracks. Working condition. Check out my other Delta 1460 lathe auctions.
|
|
|
VERY RARE Vintage 1" X 12TPI wood lathe outboard faceplate left-hand threads
SHIPPING to USA only. No charge for pick up in Vista CA 92083 This auction is for the(Brand name unknown) wood lathe outboard faceplate pictured. 6¼" diameter. 1" X 12-TPI left-hand threads for outboard turning. Made by( but will fit any lathe with 1" X 12tpi left-hand threads. Thanks for looking!
|
|
|
Delta Rockwell Milwaukee Wood Lathe Outboard Inboard Faceplate 1" LH RH Threads
6" FACEPLATE FROM VINTAGE DELTA ROCKWELL LATHE. HAS BOTH LEFT HAND(LH) and RIGHT HAND(RH) 1" X 8 TPI THREADS. CAN BE USED IN BOTH THE OUT BOARD AND IN BOARD POSITIONS. THIS FACE PLATE IS IN EXCELLENT CONDITION.
|
|
|
POWERMATICE 90 LATHE OUTBOARD FACEPLATE CASTING 1 X 8 LEFT HAND THREADS
ITEM IS OFFERED AS THERE APMPLE SURFACE AREA LEFT TO FASSION A WODDEN HAND WHEEL OF YOUR DIA THAT YOU TURN. CAN BE SCREWED RIGHT THE HUB CASTING AND YOUR GOOD TO GO AGAIN WITH AN OUT BORAD HAND WHEEL. RAGGED EDGENS LEFT EM OR SAND OFF. HUB IS CAST ALUM. THREADS ARE GOOD. THIS IS NOT NECESSARLY PREVY TO THE POWERMACTIC 90 PERHAPS OTHERS.
|
|
|
Delta Milwaukee Rockwell lathe left-hand threaded faceplate for outboard turning
Delta Milwaukee Rockwell left-hand threaded faceplate for outboard turning 1" X 8 threads-per-inch threads
|
|
|
Delta 6" inboard OR outboard faceplate 1"-8 thread
Delta 6" inboard OR outboard faceplate 1"8 thread
|
|
|
Vintage TOOLKRAFT 390A Wood Lathe outboard turning stand 12x46 faceplate steady
Vintage TOOLKRAFT Wood Lathe model 390A probably 1960's era 8 speed 12" swing 38" between centers PLUS 12" bed extension also includes steady rest outboard turning stand 10" faceplate center 3 Jaw Chuck drill chuck Lathe is mounted to a 21/2" hardwood bed on Cast iron legs and has a on off switch located on the front left. A 10" heavy guage power cord connects the motor. Lathe is in very good condition. Email me with any questions. Pick Up only unless you arrange shipping.
|
|
|
3 1/2" Bronze Outboard Wood Lathe Faceplate
Very nice 3 1/2" bronze faceplate for wood lathe is in excellent condition. It is threaded LH 1" x 10tpi for outboard turning. Any questions- please ask. Happy to combine shipping- check my other listings. Shipping calculator is often high- if you wait for my invoice accurate charges will be reflected. Local pickup in upper Bucks County. PA always welcome- COD please.
|
|
|
1961 Mercury 650 outboard faceplate
For bidding is a 1961 Mercury 650 outboard faceplate. Moto has been parted out and this is what's left!
|
|
|
Rockwell Delta wood lathe outboard hand wheel/faceplate
Delta Rockwell wood lathe outboard hand wheel. This is in fair condition. Edges of the nut are knocked off. This is cat#938. Shipping is to the continental U.S. only. Payment is to be made within 5 days of auction close by Paypal only. Thanks for looking!
|
|
|
Oliver lathe outboard faceplate wheel woodworking
Hi Original Oliver outboard lathe wheel for 159 or maybe others. Good used condition. Thanks for looking
|
|
 |