|
Lathe chuck backplate Southbend, Sheldon, Clausing, Hardinge
For sale is a backplate for a lathe. It appears unused. It is marked"8215-6 1/4"5 Made in Poland" The outside diameter is about 6-5/16" od. The hub is 3-3/8" od.
|
|
|
Lathe chuck mount victor southbend clausing
Lathe chuck mount. 9 1/4 diameter. Has 6 studs/pins. The studs measure 5 1/4 center to center. The lip on opsite end is 7 5/8. This fits against your chuck. Most likely you will need to machine this end for your chuck. Thanks for looking.
|
|
|
English made (maybe Clausing?) 3 Jaw 6" chuck
good condition used chuck. Unknown manf. Made in England. 6" 3 jaw. Externally threaded mount. Questions feel free. Thanks. Andrew. Ag6 2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28c%3Eag6%3E2-1445312d808-0x107-
|
|
|
English made (maybe Clausing?) 4 Jaw 10" chuck
Made in England 10" chuck. 4 jar. Externally threaded mount.
|
|
|
Metal Lathe 3 Jaw Chuck Extra Jaws Southbend Clausing Atlas Craftsman
Metal lathe 3 Jaw Chuck jaws. It is unknown what brand chucks they came off. They are smaller in size. The largest set is in the worst shape has some weld spatter on them but does not appear to affect the function. The other sets are in good used condition, some nicer than others. As shown in the photos- Sold as is with no returns. Unsure of application. This is used but should function as required with some cleaning up and elbow grease. Sold as is with no returns. So please ask for any additional dimensions before you buy it.
|
|
|
Buck 6" 6 jaw lathe chuck, south bend, clausing, atlas, hardinge, logan
You are bidding on a genuine Buck 6" 6 jaw lathe chuck. This has NO mounting plate. You will have to provide one to fit your lathe. This chuck comes with 6 2-piece jaws, and the removable extension of the 2-piece jaw. The extensions are stamped 10050 33. 3 of the extensions are mounted, and 3 are not, because the bolts to mount the other 3 extensions are not included. Key is included. I see no damage. The jaws are nice, they do not wiggle, are tight in ways. I see no evidence of work piece slipping in the jaws, the jaws look new. The chuck operates smooth with the key. Enco wants $577for this chuck also without a mounting plate. Free shipping is for the USA only. Please ask any questions and thanks for looking
|
|
|
Lathe spindle adapter #3 morse inner taper southbend clausing
You are bidding on a nice Lathe spindle adapter. Inner is a#3 morse taper. Will fit assorted different lathes. Measurements are; 3 inches long. Largest dia 1.762 top of taper, bottom of taper is 1.630, the straigth part at bottom of taper is 1.538. These dimentions were checked on a comparator. Thanks for looking.
|
|
|
VERY LOW HOUR 2004 NARDINI 14" X 40" LATHE clausing romi harrison leblond
Near perfect 2004 Nardini MS1440 gap bed Lathe with less then 100hrs of use. Standard and metric threading. Ways, gears spindle and tailstock tapers all in excellent shape. Comes with a 10" bison 3 jaw chuck If you have any question you can call or text me@ 406-253-4852 SPECIFICATIONS Swing Over Bed: 13-3/4" Swing Over Cross Slide: 7-7/8" Swing In Gap: 19-3/4" Distance Between Centers: 40" Cross Slide Travel: 8" Top Slide Travel: 4" Spindle Bore: 1-5/8" Spindle Nose: D1-5" Spindle Speeds: 18) 31.5 to 2500 RPM Tailstock Quill Diameter: 2" Tailstock Taper: No. 3 MT Tailstock Quill Travel: 5-1/8" Number of Threads: 192 Metric Threads: 45) 40 to 7 Inch Threads: 48) 3.5-42 TPI Module Threads: 48) 1 to 1.75 Diametral Pitch Threads: 48) 14 to 168 Pitch Of Leadscrew: 4 TPI Number of Feeds: 192 ... moreLongitudinal Feeds. Inch: 0016 to.399 in/rev Longitudinal Feeds. Metric: 042 to 1.013 mm/rev Cross Feeds. Inch: 0007 to.0213 in/rev Cross Feeds. Metric: 019 to.542 mm/rev HORSE POWER.6- 3/4 HP ELECTRICS: 220/3PH/ Weight: 2830 Lbs.
|
|
|
17" X 80" CLAUSING COLCHESTER GAP BED ENGINE LATHE: STOCK #62007
17" X 80" CLAUSING COLCHESTER GAP BED ENGINE LATHE 17" X 80" CLAUSING COLCHESTER GAP BED ENGINE LATHE: STOCK# 62007 SPECIFICATIONS SERIAL. 7/0018/03306 MODEL. 17 SWING OVER WAYS. 17" SWING OVER CROSS SLIDE. 10-1/2" SWING IN GAP. 28" DISTANCE BETWEEN CENTERS. 80" SPINDLE SPEEDS. 16) 20 TO 1600 RPM DIAMETER OF SPINDLE HOLE. 3-1/16" FEEDS LONGITUDINAL. 45) 002 TO.032 IPR THREADS(ENGLISH) 38) 2 TO 72 TPI THREADS(METRIC) 40) 4 TO 14 MMPI CROSS FEEDS. 001 TO.016 TAPER IN TAIL STOCK. 5 MT CHUCK. 10" 3 JAW STEADY REST. 7" ROLLER HARDEN WAYS. YES FORWARD& REVERSING. YES COOLANT. YES MOTOR. 10 HORSEPOWER CALL US FOR SHIPPING QUOTES YODER MACHINERY STOCK#62007 We accept Visa. Master Card, American Express, Discover. We also accept Paypal. All purchases under $ 100.00 are expected to be paid ... morewithin three days of end of auction. Multiple and single winning bids, totaling between $100.00 to $ 999.00 will need to be paid within two days of end of auction. Multiple and single winning bids over $ 1,000.00 need to be paid by the next business day and we ask that you have your finances in order before end of auction. Buyers are responsible for all shipping and handling charges. Please know the cost of shipping before placing your bid. If you have your own truck. Trailer or have arranged your own freight we can load your large item or machine free of charge. All orders being shipped to PO Boxes must be delivered via the United States Postal Service(USPS) Shipping rates are available at www.usps.com. Weight restrictions may apply. The United Parcel Service is another option for packages under 150lbs. Shipping rates a
|
|
|
CLAUSING 20" FLOOR MODEL DRILL PRESS IN FABULOUS CONDITION
I have for you a 20" variable speed drill press made by Clausing in great condition. In the U.S. Clausing drill presses are considered the best. I took this machine out of service and have oiled up all bare surfaces for protection. This machine is 1 1/2 HP. Three phase, 220 volts. It has an adjustable production table with a few inconsequential drill marks. This machine has a chuck which attaches to the spindle with a#3 Morse taper. The chuck has a key that is attached to the machine with a chain. The spindle speeds are in two ranges from 150 to 1000 rpm and 300 to 2000. This machine has a light on a flexible extension which was professionally attached. It appears to me that this machine has seen little use, it was in a large shop with many CNC machines so it was not a a primary use machine. I can ship the item to you at your setup and ... moreexpense or local pickup is always welcome. This machine weighs about 1200 lbs. The strap you see on the head is not a part of the drill press it is what I used to lift the machine. Payment is due within three days from end of auction. I accept Paypal. I will work with you if you want to ship this press but the buyer will have to make all arrangements. No international bidders please. This auction is only for the drill press. Any other items displayed are not INCLUDED in the auction. Just a word about myself. I am an avid cook, mechanical engineer, woodworker and lover of copper pots though I use a lot of cast iron and pottery in my cooking too. I am also working on becoming more versed in blacksmithing. I love great craftsmanship and clever devices especially those that will make my life easier. Since my family is from Europe I am partial towards quality products. I look forward to bringing my findings to you. If you have any questions I will do my best to answer them.
|
|
|
Clausing 8520 mill motor bracket and pulley
Motor mount and pulley assemble. Have one new bearing but ear is broken off and do not have. shipping is about $25.00 can't fiqure out on page
|
|
|
Metal Lathe #4MT Dead Center Southbend Clausing Atlas Craftsman
Metal lathe Dead Center. It is#4 Morse Taper. Small end measures 1.020" As shown in the photos. Some evidence of wear on the tip, could be refaced or used as is. This is used but should function as required with some cleaning up and elbow grease. Sold as is with no returns. So please ask for any additional dimensions before you buy it.
|
|
|
Milling Machine R8 Boring Tool Holder Southbend Clausing Bridgeport
Milling Machine boring tool holder. It is for R8 type machines. As shown in the photos. Has some staining and rust from years of sitting around. The end has"India" stamped in it. This is used but should function as required with some cleaning up and elbow grease. Sold as is with no returns. So please ask for any additional dimensions before you buy it. 1?RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2B%3E%3B1%3F-14469844960-0x10c-
|
|
|
Metal Lathe #3 MT Boring Tool Holder Southbend Clausing Atlas Craftsman
Metal lathe boring tool holder. It is#3 Morse Taper. As shown in the photos. Has some staining and rust from years of sitting around. Looks like it will hold a square tool bit. This is used but should function as required with some cleaning up and elbow grease. Sold as is with no returns. So please ask for any additional dimensions before you buy it.
|
|
|
MACHINIST TOOL LATHE HUGE LARGE Lathe Steady Rest Machinist Lathe for Clausing ?
PLEASE SEE MY OTHER AUCTIONS FOR A LARGE SELECTION MACHINIST ITEMS. I WILL COMBINE SHIPPING. THE EBAY SHIPPING CALCULATOR MIGHT BE WRONG, PLEASE WAIT UNTIL I SEND THE INVOICE AT THE END OF THE SALE. I do not know much about these so I am selling it AS IS with no returns. The pictures show all that is included and the condition so please look close. Please see my other auctions for more tools items from a local estate. I will combine shipping. Contact me for a shipping quote. I tried to take photos of the parts that came with it. if there are any questions, please do not hesitate to email me with any questions.PLEASE SEE THE PHOTOS FOR THE BEST DESCRIPTION. Sold"AS IS" with NO REFUNDS OR RETURNS! NO EXCEPTIONS. I will combine shipping. Please email me for combined shipping rates. PLEASE KNOW THAT I TRY TO SATISFY ANY AND ALL OF MY ... moreCUSTOMERS. IF THERE IS A PROBLEM WITH YOUR PURCHASE, OR ANY OTHER QUESTIONS, PLEASE, DO NOT HESITATE TO EMAIL ME. I ANSWER ALL EMAILS AND WILL TRY TO WORK WITH YOU AS BEST I CAN. I WILL, HOWEVER, NOT BE BULLIED OR BLACKMAILED. THERE SEEMS TO BE SOME BUYERS THAT TRY TO SHAVE MONEY OFF OR CLAIM THINGS THAT ARE NOT TRUE. SO PLEASE, IF YOU ARE ONE OF THESE PEOPLE, DO NOT BID.LL
|
|
|
CLAUSING KONDIA MODEL FV-1 VERTICAL KNEE MILL W/ PROTO TRAK SM2 CONTROL
Welcome to Select Machine Tool Item Description: Used Clausing/Kondia FV1-48VS08 Vertical Knee Milling Machine w/ Proto Trak SM2 Control Specifications: 9" x 48" Table 36" Longitudinal Travel 15" Cross Travel 16-1/2" Vertical Traverse 23" RAM Infinitely Variable Spindle Speed- 60-4000 RPM Net Weight- 3.040 lbs R-8 Spindle Taper Serial No. AD-1 Equipped With: SWI Proto Trak SM-2 Control Power Drawbar Auto Lube Stock No. 04453 History: When you buy from Select Machine you are not only buying from a reputable dealer but also a sales and service staff with well over two hundred years of combined experience. We want you to be happy and we also want to help you in any way possible. So if you have a question or are looking for something special please call or e-mail us so that we may earn your business. We want to build ... morerelationships with our customers and the best way to do that is by providing quality products. Honest representations, value, and service. Again. We want to thank you for your time and interest and we look forward to earning your business in the near future. Shipping& Payment: All forms of payment will be accepted; personal checks will need to clear before your item will be shipped. In order for this to be an enjoyable experience. Please ask all questions before purchasing. All items will be shipped using UPS. Which includes free insurance up to $100. Large items will be shipped using freight carrier. Shipping will be calculated based on weight and your zip, you can obtain an approximation at UPS.com. Yes, we do combine shipping whenever possible. If you have any questions please e-mail us, and we will try to reply within 24 hours. Thank You for stopping by and please view our other items. If you are a Virginia resident 5% state sales tax will be added.
|
|
|
Jacobs Spindle Nose Chuck Model 91-t0 L0 mount Metal lathe for Leblond Clausing
Jacobs spindle nose lathe chuck includes a complete set of collets ranging from 1/16 to 1 3/8 in. Also has a few rubber stoppers.the chuck. It is a L0 that is in good condition and working fine. The collets are in decent shape, the boxes are in average condition. One box dose not like to close but both boxes have dents and scraps in them. The chuck is a model#91-t0. This part can be picked up from my shop which is 10 miles south and east of downtown Saint Louis. Missouri, forklift loading is free. Please check out my other auctions. Thanks for looking. This machine is for sale locally. So the auction may be cancelled due to a local sale. Please read our feedback. 100 percent customer satisfaction is our goal. Payment to be received within 7 days of the end of auction. Items are described as accurately and honestly as I can but are sold as ... moreis unless otherwise specified, so please ask questions. Due to items not being picked up in a timely manner: Machines that are being picked up will be stored free for 14 days. buyer will be charged $10 per week there-after for storage unless prior arrangements are made. Items not picked up within 60 days will be resold. Please do not bid unless you intend to pick up your item in a timely manner.
|
|
|
5.5" VINTAGE MACHINERY CAST IRON HAND WHEEL ROCKWELL CLAUSING LATHE MILL GRINDER
This is a 5.5" diameter machinery hand wheel probably from a lathe. Milling machine or grinder etc. It's made of cast iron with a swivel knob and it weighs approx. 3.6lbs. Please see the pictures for exact condition and sizes. Hopefully it's perfect for that machine that you're building. Don't miss this as it includes super-fast FREE priority mail shipping! See my other auctions for different size vintage hand wheels* PAYPAL(Ebay no longer allows me to accept American dollars unless the item is picked up in person) Items must be paid for within 7 calendar days of auction end(if you need a few more days. Just let me know) After 7 days I must file a non-paying bidder report in order to retrieve my fees from ebay. ~~~SUPER-FAST SHIPPING! ~~~ ITEMS PAID FOR BY 12 NOON WILL NORMALLY SHIP OUT THE SAME DAY! This can mean you ... morewill get your item in 2-4 days! See my feedback for positive comments on fast shipping& packing! I ship Via USPS and UPS(my choice) depending upon the item being shipped and I pack your items very carefully. All shipments are sent confirmed delivery but if the buyer requires insurance they should contact me. Return shipping: If I made a mistake(Rare. But it happens) I'll pay the return shipping. If it wasn't my fault, the buyer can pay for the shipping. I try to describe everything I sell as honestly as possible and my feedback reflects this. Due to the unique& vintage nature of the items I sell it is sometimes hard to describe every flaw. If you should have a problem upon receiving your item and you are not happy. Please contact me with any concerns you may have. FEEDBACK NOTE: Feedback is now very important for sellers on Ebay. If you were satisfied with my service PLEASE take a second to give me a good star feedback rating. This will enable me to continue to keep costs down and prices reasonable. I will automatically leave you positive feedback in return. Thank-you! I am located in: Panorama City. Los Angeles, Ca, 91402(Local pick-up is only allowed on bulky i
|
|
|
Clausing Twin 20" Drill Press on 40X24 Table, DRO Scale, Coolant & Splash Guard
You are looking at one of the most productive drill presses you will ever see. It has a complete coolant system with a return to a tank in the table base. A splash guard to keep it contained and a digital scale on one of the heads for accurate depth control. The step pulleys are super quiet and the drills look and run like new. We will even give you a 1 year warranty like new! CLAUSING 20" DUAL HEAD DRILL PRESS STEP PULLEY WITH 208-220/440 3-PHASE MOTORS 40" X 24" CAST IRON TABLE/ 43" COLUMNS COOLANT SYSTEM WITH NOZZLES FOR BOTH DRILLS 115V COOLANT PUMP WITH TANK SPLASH GUARD DIGITAL SCALE ON ONE OF THE HEADS This unit has been"reconditioned" Repainted and is in excellent mechanical condition. It wasn't at all bad to start with, but it's really like new now. Everything works like it should and it is ready ... moreto go into service immediately. No apologies here! This drill press features some of our latest innovations: Digital Scale. Coolant System and Splash Guard. This drill press has a cast iron table and is very heavy. We can help with freight quotes if you need. Just let us know! Overall table size: 40" x 24" x 35" H igh Step p ulley HP: 1.5 drive motors RPM: 1725 Voltage: 208-220/440. 3-phase Please contact us if you have any questions at all. We have several trucking companies we work with regularly and we can help you get trucking quotes. We encourage you come and see this Drill Press located in Eastlake. Ohio
|
|
|
13 x 36 CLAUSING COLCHESTER GEARED HEAD ENGINE LATHE A-0625
You are bidding on a Clausing Colchester 13" x 36" Lathe Specifications Specification Description NEW APPROXIMATELY 1968 SWING OVER BED 13" SWING OVER CROSS-SLIDE 8" DISTANCE BETWEEN CENTERS 36" SPINDLE BORE 1.625" SPINDLE SPEEDS(GEARED HEAD) 40- 1800 RPM MAIN MOTOR 3 HP BED WIDTH OF WAYS 11" TAILSTOCK QUILL DIAMETER 1.75" TAILSTOCK TRAVEL 4.5" TAILSTOCK TAPER NO 4 MORSE DIMENSIONS APPROXIMATELY 72" x 36" x 60" WEIGHT APPROXIMATELY 3000 LBS Additional: 2) 1/2" Drill Chucks 5C Collet Closer 12" Face Plate 7 1/2" 3 Jaw Burnerd Chuck-2 Pcs Jaws 220/3 Phase European Style Quick Changing Tool Holder 12 Position 4" Square Tool Post Turret Bed Turret w/ 1" Hole Runs QuietlyGood Condition/Loaded Good Condition: Item is free of any significant dents. Marks, imperfections ... morethat would impair the functioning of the item(unless specified in the description) Good Usable Condition: Item may have dents. Marks, imperfections that do not impair the functioning of the item(unless specified in the description) Machines/Tools that cost above $500.00 please pay with credit card or wire transfer. We guarantee that the item purchased is packaged exceptionally well. Once it is picked up by a common carrier(UPS etc) we lose control over how the item is handled. If you receive an item and it(or the box) appears damaged. Do not sign or accept. If the item is left at your home or business. And you later find that it is damaged, take pictures and notify the carrier. If you are pleased with our service and product would you kindly leave positive feedback. Thank you. inkfrogproseries. The machine/item is located in Bay Shore. NY 11706 Shipping costs to buyer location are not included with the machine price We can provide a freight quotation, buyer works directly with the shipper Crating/Palletizing: Some buyer's need to use a freight company requiring the item to be crated or palletized. If this is required, we quote crating or palletizing seperately and it
|
|
|
Lathe tool holder, Boring bar,machinist tools,Southbend,Logan,Clausing,Monarch?
Lathe boring bar and holder. Shank is 1" X 3/4"
|
|
|
001 Clausing Lathe Milling Vise Attachment #7525 Atlas 12" Mk3 4800
Clausing model no. 7525 milling vise in very good condition. Ways are clean. Motion is tight, and functions as it should. Some minor milling marks on the vise, as pictured. The nut and screw appear to have about 10-15 thousands of hysteresis. Base is just under 4" OD(about 3 15/16" I obtained this with a Clausing 12" MK3a lathe but it looks like it will fit many others. Comes with cheap wrench shown(fits the angle adjustment nuts) and what appear to be the original factory V-blocks. Handle will be removed for shipping. We are happy to combine shipping for multiple item purchases. Please email us for a shipping quote!
|
|
|
clausing drill press model 2217 with multi drill head
clausing 2217 used drill press with multi drill head/ 3 phase
|
|
|
1-Set of Clausing Model 1666 - Multi-Spindle Drill Presses - Used - AM9981
1-Set) CLAUSING Model 1666 Multi-Spindle Drill Presses- Used- AM9981 Model: 1666 Serials: 515578& 515579 Specifications: 2) Spindle Drill Presses Quill Travel on Each Spindle: 5” Distance Between Face of Column and Center of Spindle: 6-3/4” Table Dimensions: 55” W X 25” D(2) Integrated.75 HP Motors 220/440 Volt. 3 Phase Electrics This machine is on our floor available immediately. Subject to prior sale DISCOUNTED SYSTEM PRICE | A S PICTURED | LOADED ON TRUCK | FOB CLEVELAND. OHIO Do not hesitate to call with any further questions and we look forward to doing business with you. A M INDUSTRIAL- EBAY DEPARTMENT- 216-433-7171– www.amindustrialmachinery.com…Dust Extraction…Fabricating Machinery…Sawing& Cutoff…Tube& Pipe… New Arrivals Daily! Conditions: Used items sold hereunder are neither designed nor manufactured by the seller, and ... morethis sale of these items is on an as-is and without any representations or warranties. Expressed or implied, of any kind including safety, condition, or quality. Seller further assumes no responsibility to provide safety devices or equipment necessary for the protection of the user or to comply with applicable governmental laws or requirements. It is agreed and understood that purchaser assumes this responsibility and the above is an integral part of this sale. All sales are F.O.B. Cleveland. Ohio unless otherwise specified.
|
|
|
Clausing 20''Drill Press model 2220 in excellent condition,
Here is my 20' clausing drill press I bought new in 2001 And has been in my hobby shop since then.I added a head positioning mechanism. The 1 HP 1Ph 1140 RPM Baldor Motor Pictured with the drill press is not included with the drill press. The Baldor motor sells separate for $350.00 If wanted. The 6 inch Henrich Vice V block attachment also sells separate for $250.00 for both V block and Vice. Jacobs Drill Chuck model 36B 3/16-3/4 capacity& arbor/key also sells separate $150.00. The drill press is $2500.00 with the Safety Manual. Parts List and Clausing Drills brochure. Local Pickup is strongly Preferred.
|
|
|
MT 2 DEAD CENTER ATLAS CRAFTSMAN LOGAN SOUTH BEND CLAUSING LATHE
MT 2 DEAD CENTER IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH CONFIDENCE. I WILL COMBINE SHIPPING WHEN POSSIBLE. IF YOU PURCHASE MORE THAN ONE OF MY ITEMS PLEASE ... moreGIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM.IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS 3c0.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d71f%2B%3E3c0-14492714d05-0xe5-
|
|
|
Armstrong wrench Set. Metal Lathe South Bend Clausing Craftsman
For sale is a very nice set of Armstrong wrenches. The three box end wrenches are Armstrong brand. The spanner wrench is unknown brand. The Armstrong wrenches show some wear and evidence of age but are all in useable condition. There is a 1/2" a 7/16" and a special type wrench Armstrong number 8. It is old. Therefore sold with no returns. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*a4%601gc%3E-14492714d0f-0x112-
|
|
|
ATLAS 6" DOG DRIVE FACEPLATE # 9-15 CRAFTSMAN SOUTH BEND LOGAN CLAUSING LATHE
ATLAS 6" DOG DRIVE FACEPLATE# 9-15 1 1/2" X 8 TPI IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH CONFIDENCE. I WILL COMBINE SHIPPING WHEN POSSIBLE. IF ... moreYOU PURCHASE MORE THAN ONE OF MY ITEMS PLEASE GIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM.IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS
|
|
|
Clausing 12" Metal Lathe Back Gear Handwheel for 5900 Series
This is not a very pretty handwheel but the problems are all cosmetic. This handwheel is no longer available from Clausing Please visit our website. Lostcreekmachine.com To see more tooling from Lost Creek Machine. Check out my! If we can combine more than one small item shipping may be less. Illinois residence and anyone picking tools up at the shop must pay 6.5% sales tax unless the proper forms are provided. We accept Visa. MasterCard, Discover, and PayPal. If you have a question call us M-F 8-5 CST and Saturday 8-Noon, 815-434-5897. You can email us anytime
|
|
|
Clausing lathe Spindle nose protector-LOO
Used spindle nose protector for L00 spindles-Fits 5900 series Clausing and others
|
|
|
Clausing 5900 Series Lathe carriage lock
Used carriage lock for 5900 series Clausing lathes Posted with
|
|
|
CLAUSING 7 1/2" 3 JAW NO. BP66 / 3812 LATHE CHUCK L-00 L00 TAPER MOUNT 6714
HERE'S A GOOD HEAVY DUTY SOLID 7 1/2" 3 JAW LATHE CHUCK NO. BP66/ 3812 THAT CAME OFF A CLAUSING LATHE. HAS A L-00 OR L00 TAPER MOUNT AND THE BACK IS STAMPED 6714. REVERSABLE JAWS AND THE ONLY DAMAGE I SEE IS THE ONE JAW HAS THE CORNERS CHIPPED OFF THE FIRST THREAD AS SHOWN IN THE PICTURES. HAS A 2" THRU THE CENTER HOLE SIZE USES A STANDARD 7/16" SQUARE KEY BUT NONE SOLD WITH THIS CHUCK. THIS AND IS A HEAVY DUTY CHUCK THAT WEIGHS ROUGHLY 36 LBS. PLEASE LOOK AT THE PICTURES AS THEY ARE PART OF THE DESCRIPTION ALSO.
|
|
|
Jacobs 18N Super Chuck 1/8" - 3/4" 2 MT Atlas Clausing Southbend Logan Lathe
This is a used 18N Jacobs Superchuck with 1/8 to 3/4" capacity. In good working condition with a new Jacobs 2MT to 4 Jacobs Taper shank. Has some scratches and nicks from use. Has a number scribed on it, see pictures for condition. I combine shipping whenever possible, if you win multible auctions, please wait for an invoice from me. Or pickup is always welcome. Thanks for looking. Powered by The free listing tool. List your items fast and easy and manage your active items.
|
|
|
Clausing Colchester 8100 Engine Lathe Turning Steady Rest 4 Jaw Chuck Tailstock
Clausing Colchester 8100 Engine Lathe Machine is in excellent condition and can be seen under power as needed Specifications: Model.8100 Swing Over Bed.21" Swing Over Cross Slide.14.5" Distance Between Centers.84" Spindle Speeds.16) 20-1.600 RPM Spindle Nose.D1-8 Hole Thru Spindle.3.5" Threads.Inch/Metric Inch.38) 2-72 TPI Metric.45) 0.4-14mm Feeds.45) 0.002"0.016" Cross Slide Travel.12" Tailstock Quill Taper.5 MT Tailstock Quill Travel.7" Dimensions.138"L x 42"W x 52"H Approximate Weight.9.000 LBS. Equipped With: 3-Jaw Chuck 4-Jaw Chuck Steady Rest 7" Coolant System Horsepower 121/2 All Available Manuals Please contact Jason Stob 708 790-3358 with any question
|
|
|
Clausing Instructions & Parts List 6900 Series 14" Lathes
Very good.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*a4%601gc%3E-144a01a6247-0x10b-
|
|
|
JACOBS 18N DRILL CHUCK W/ MT4 & KEY SOUTH BEND ATLAS CLAUSING LOGAN LATHE MILL
JACOBS 18N DRILL CHUCK W/ MT4& KEY OPERATES SMOOTHLY. IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH CONFIDENCE. I WILL COMBINE SHIPPING WHEN POSSIBLE. IF YOU ... morePURCHASE MORE THAN ONE OF MY ITEMS PLEASE GIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM.IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS
|
|
|
15" CLAUSING (USA made) DRILL PRESS - Floor Model
ebay template 15" CLAUSING(USA made) DRILL PRESS- Floor Model Has a tilting and rotating table. Includes Jacobs 0- 1/2" capacity drill chuck 3/4 HP Motor Variable speed drive 330 to 4000 rpm Drill to center of circle: 15" dia. Capacity. Hand feed: 5/8" dia. Spindle travel: 4-3/4" Table size 14" x 10" Power: 220 Volt. 3 Phase Machine height 72" Machine weight 300 lbs. Shipping Shipping is the responsibility of the buyer; however. Machinery Exchange has a large network of freight carriers to help you find the best price. If you would like a freight quote for this item please click"Contact Seller" or“Ask Question” at the bottom of the listing and provide us with your city, state and zip code. Or contact us via telephone at(818) 718-6734 Machines are attached to a skid for and covered in protective ... morecosmoline coating for shipment. A forklift may be required to remove the machine from its skid. The cosmoline can be removed using a light kerosene/water mixture. Tooling: Below are directions on how you can calculate shipping for items under 150lbs. That does not qualify for USPS Flat Rate. Pick up/Will Call: All our items are available for pick up Monday thru Friday from 9am to 4:30. Arrangements can be made for Saturday pick up. We do not charge loading fees for loading machines or tooling unless we have to bring in special equipment or call a mover. Note: Most of our listings are marked Freight shipping. We ship via FEDEX and USPS for item(s) 150lbs or lighter. The cost of shipping will be sent via invoice. We encourage all customers to log into the FedEx website to calculate shipping. Listed on every item are the directions and information needed to do so. Payment We accept Check. Credit Card, or PayPal. We accept all major credit cards except American Express. Payment is due within 5 days of purchase. Orders are not processed until they’re paid in full. Our invoice will include a subtotal of item(s) purchased. Sales tax for in-state purchases[CA] and a rigging/packagi
|
|
|
Union 8" three 3 Jaw Lathe Chuck L00 LOO mount back nose threaded USA clausing
This is a Union(U.S.A. made) 3jaw lathe chuck with L-00 mount native(not a backplate) This chuck has a ring around the O.D. of rust. You can see in the pic. It also has a few dings here or there. However, none of these cosmetic issues alter the function and I think this should be a good working chuck for someone. Probably pretty good shape for it's age, the jaws look pretty nice overall, should be a nice chuck all in all. The bid price will be the TOTAL PRICE SHIPPED!
|
|
|
L0 LO Long Taper to 1"- 8 TPI Adapter Back Plate Leblond Clausing Sheldon
6" Diameter L0 Taper to 1" 8 TPI Spindle Thread Adapter. Please visit our website. Lostcreekmachine.com To see more tooling from Lost Creek Machine. Check out my! If we can combine more than one small item shipping may be less. Illinois residence and anyone picking tools up at the shop must pay 6.5% sales tax unless the proper forms are provided. We accept Visa. MasterCard, Discover, and PayPal. If you have a question call us M-F 8-5 CST and Saturday 8-Noon, 815-434-5897. You can email us anytime
|
|
|
MCL-435 ROCKWELL LATHE 7" Drive Face Plate L00 Spindle Clausing
Rockwell MCL-435 Faceplate 7” Diameter Fits L 00 Spindle This listing is for one Rockwell 7” diameter faceplate for an L00 spindle. The drive plate is free from any chips. Cracks, breaks, welds or repairs. It is used but it has not been abused. The threads, keyway and taper all appear to be in good condition. If you have any questions or would like to see any different or more detailed photos. Please do not hesitate to ask, I will be happy to oblige. Shipping will be combined whenever and wherever possible. Thank you for your time in looking and for your interest, and please be sure to check out my other auctions, thank you. Unless otherwise specified in the auction listing all items will be shipped by USPS Priority Mail. This includes a tracking number and insurance for the item. Any item sold for over $50 will have the appropriate amount ... moreof insurance added. In the event of larger and heavier items. They will be shipped by the cheapest carrier possible(in most cases, Fedex) If bidding from outside the U.S. Canada or overseas) please be sure to notify me before the end of the auction so I may give you an estimate of the shipping cost. In most all cases of an item being shipped to Canada or Overseas, all packages/parcels will be shipped through the United States Postal Service(utilizing Flat Rate boxes wherever possible) no exceptions. This will usually be the cheapest route available. Payment methods are listed in the auction details under shipping and payments, PayPal is accepted as well as other methods. If you are the winning bidder and intend to pay by a method other than Paypal, please notify me at the end of the auction. Starrett Lufkin browne sharpe mitutoyo union Armstrong steam steampunk punk vintage Clausing regal leblond Cincinnati lodge Shipley atlas
|
|
|
Lantern type tool holder 5/8" tools 12 to 14 inch lathe Clausing Logan Atlas
Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Rocker type tool post for 12” to 14” lathe. This one was part of the tooling package for a Clausing 12’ lathe. Tool post body diameter is 1.2" Stands 4 1/32" tall not counting the bolt. Clamping bolt is ½” diameter X 3” long. With a ½” square head. Post slot is.625” wide. Slot length is 2.100” Clamp bolt is mostly free and moves freely with light pressure with a wrench. It’s a little too tight to move completely by hand. Threads on end of bolt are mushroomed slightly. So it can’t be easily removed completely. The bolt could be removed and cleaned up easily if you wanted to put a little bit of work into it. I could have cleaned it up to work freely. But many buyers want them in original condition. There is a light brownish patina on the parts, which ... moreI have not removed. The holder is fully functional just as it is. Smaller washer is 1 3/4” X 2 1/32” X ¼” thick. This one fits the post perfectly. 2nd larger washer is about 2” X 2 3/8 X 7/16” thick. And was probably made to fit a certain lathe. You would need to machine it to fit your lathe, or make a similar washer to match your lathe. Rocker is 3” long and 5/8” wide. Matching washer is 3” diameter. A nominal 5/8” tool fits in the slot easily.
|
|
|
lathe quick change tool post, machinist tools, monarch,clausing,Lathe
Aloris style toolpost. Don't know the brand very large. Seems to work well needs handle and mounting bolt and bracket
|
|
|
ATLAS CLAUSING LATHE Electric Motor Mount
This is a motor mount for Clausing and Atlas Clausing lathes. Probablablt made in the late forties to early 50's. Cast iron construction with a 1" pin. This would bolt onto either a cabinet or leg under these lathes.
|
|
|
ATLAS LATHE CRAFTSMAN CLAUSING VERNIER CALIPER 14in.
THIS IS A HEAVY DUTY STAINLESS STEEL VERNIER CALIPER WITH FINE ADJUSTMENT MICRO ADJUSTMENT SCREW AND LOCKING SET KNOB JAWS LONG FOR INSIDE MEASUREMENT CASE INCLUDED ag6 2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28c%3Eag6%3E2-144aa824377-0xfc-
|
|
|
Set of Metal Lathe #2MT Dead Center Southbend Clausing Atlas Craftsman
Set of Metal lathe Dead Centers as shown in the photo. They are all#2 Morse Taper. As shown in the photos. Wear on the tips, one tip has been cut off, but all should be useable as is or with a little refurbishment. This is used but should function as required with some cleaning up and elbow grease. Sold as is with no returns. So please ask for any additional dimensions before you buy it. 2p5ddv.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2B26rk%3E2p5ddv-144aa8591d0-0xf2-
|
|
|
Clausing Drill Table - Machine Base - Layout Table - Machine Table
This is a vintage Clausing cast iron drill table. Unit measures 34.25" long OAL x 25.5" wide OAW x 32.25" high OAH. Machined portion of table measures 19.625" wide x 28" long. There is a 2" wide coolant trough that runs around all four sides with a drain/return bung. Table is in good condition for its age. Some of the holes in the top are drilled and tapped while 95% of the holes seen in the photos are drill pecks. Table would make a good foundation for a drill or a layout table or a base for a surface plate the sky is the limit. Table weighs 275 pounds so pick up is prefered. However if you want to pay the freight I would be willing to disassemble and palletize for a small fee.
|
|
|
CLAUSING 5-C COLLET SLEEVE ADAPTER 5900 6900 SERIES 12" & 14" LATHE VERY GOOD 5C
I BELIEVE THIS IS A CLAUSING 5-C COLLET SLEEVE ADAPTER FOR 5900 6900 SERIES 12" 14" LATHE BUT I'M NOT 100% SURE HERE ARE THE MEASUREMENTS CHECK TO BE SURE IT FITS YOUR LATHE. Overall-3.57 long Out Side Taper- 2.38 to 2.21 Inside nose after taper for collet- 1.3 id and 1.25 inner surface with a pin. A 5c collet fits nice and tight.
|
|
|
RARE - vintage, POSTCARD , Clausing's Post Hotel und Pfarrkirche, St Martin
Click Here. Double your traffic. Get Vendio Gallery- Now FREE! Hello. And welcome! You are bidding on: A vintage postcard from St Martin it has some creases and a small tear at top- see images Please check out my! Be sure to add me to your! FEEDBACK: I WILL ABSOLUTELY PROVIDE FEEDBACK ONCE YOU'VE RECEIVED AND ARE PLEASED WITH THE ITEM AND PROVIDE MY FEEDBACK. If there is a problem. When you receive it. Let me know. But I strive to provide accurate details; both good and bad, so there should be no variation from what I describe, and what you receive. NOTICE: No unpredictable. Arbitrary ratings to study and decipher. NO GUESSWORK! I define and describe everything with detailed descriptions so there will be no negative surprises for any item that is less than MINT. However; if I make a mistake of omission. PLEASE contact me and we'll ... morework it out to our mutual satisfaction. IF YOU'RE NOT GOING TO PAY WITHIN 7 DAYS, PLEASE. PLEASE PLEASE. CONTACT ME! After 10 days. And no communication from you, I will consider canceling the bid. Please be considerate to sellers. Communicate. shipping: I will combine shippin
|
|
|
Buck 6 jaw lathe chuck D1-3 mount w/ wrench 6" AJUST TRU 10EE clausing So. Bend
Selling a Chuck for a metal lathe. It is a 6 jaw buck AJUST TRU chuck. It is 6 inches in diameter. It is in good condition. It includes the chuck wrench. It is mount style D1-3. The price is just for the chuck and chuck wrench. Feel free to make us an offer. Thanks FEEL FREE TO CALL US AT ANY TIME WITH QUESTIONS. WE WILL BE GLAD TO DO WHAT WE CAN TO ANSWER. 717)926 3975. FLAT RATE SHIPPING OF 40 DOLLARS LOCAL PICK UP IS MORE THAN WELCOME. BUT IF PICKED UP LOCALLY, A 6% PA SALES TAX WILL APPLY. WE CAN ALSO TAKE A CREDIT CARD OVER THE PHONE OR IN PERSON. PLEASE FEEL FREE TO CALL US AT 717-926-3975. THANKS, CENTRAL PENN MACHINERY
|
|
|
Clausing Lathe Tail Stock with Fixed Center
856-881-3185 SKU: AFP101 Clausing Lathe Tail Stock with Fixed Center. Condition: Used Lot# AFP101 10.6.B Fits Clausing 100. 200 series along with the 4800, 5300, 5400, 5500 and 6300 models all 12" lathes. We strive to deliver 5-star customer service. Bid with confidence! We Ship UPS GROUND to United States& Worldwide. Large items will ship Truck Freight. Contact us for rate quotes. You will need a forklift to unload. Lift gate is available at an additional charge. You are welcome to pickup at our NJ facility. M-F 7:30 AM- 4:30 PM& SAT 8-NOON. The buyer is responsible for all shipping& handling costs. Shipping costs are determined by your zip code& item weight. SHIPPING WILL NOT TAKE PLACE UNTIL PAYMENT IS RECEIVED. ATTENTION INTERNATIONAL BUYERS: Please provide a phone number and shipping address. Do not forget about ... moreany additional charges which are charged by the carrier. This is something we have no control over and is an additional charge to the shipping. WE DO NOT ACCEPT RETURNS. ITEMS ARE SOLD"AS IS" IF FOR SOME REASON YOU RECEIVE SOMETHING THAT DOSENT RESEMBLE THE PHOTOS AND DESCRIPTION IN THE LISTING WE WILL MAKE AN EXCEPTION. AUCTIONS WITHOUT A BID MAY END AT ANY TIME AS THE ITEMS ARE ALSO FOR SALE AT OUR LOCAL FACILITIES. WE ACCEPT PAYPAL PAYMENTS AND CREDIT CARDS(VISA/ MASTER CARD/ DISCOVER) PLEASE NOTE THAT WE ARE NOT AN AUTHORIZED DEALER FOR ANY OF THE ITEMS WE LIST ON EBAY. THEREFORE WE DO NOT GUARANTEE THAT THE ITEM FEATURED IN THIS LISTING WILL BE COVERED BY THE MANUFACTURER'S WARRANTY OR SUPPORT. HOWEVER. CUSTOMER SATISFACTION IS VERY IMPORTANT TO US. PLEASE FEEL FREE TO SEND US AN EMAIL OR A MESSAGE THROUGH EBAY WITH ANY QUESTIONS, COMMENTS, OR CONCERNS. BUYERS: CHECK OUR FEEDBACK AND BID WITH CONFIDENCE. SHOULD A PROBLEM ARISE PLEASE CONTACT US BEFORE LEAVING NEUTRAL OR NEGATIVE FEEDBACK; THIS WILL ALLOW US TO WORK WITH THE BUYER TO RESOLVE ANY PROBLEMS. BY PHONE: Call(856) 881-3185. Monday thru Friday 8:00 am to 4:00 pm EST, to speak with a Customer Service re
|
|
|
NICE KNOB FOR A 16" CLAUSING LATHE MACHINIST PART
NICE KNOB FOR A 16" CLAUSING LATHE IN THE 3 rd PICTURE I'M TRYING TO SHOW THE GEAR TEETH INSIDE THE KNOB. IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH ... moreCONFIDENCE. I WILL COMBINE SHIPPING WHEN POSSIBLE. IF YOU PURCHASE MORE THAN ONE OF MY ITEMS PLEASE GIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM. IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS
|
|
|
NICE HANDLE FOR A 16" CLAUSING LATHE MACHINIST PART
NICE HANDLE FOR A 16" CLAUSING LATHE IN THE 3 rd PICTURE I'M TRYING TO SHOW THE GEAR TEETH. IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH CONFIDENCE. I ... moreWILL COMBINE SHIPPING WHEN POSSIBLE. IF YOU PURCHASE MORE THAN ONE OF MY ITEMS PLEASE GIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM. IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*05e54c%3E-144ba41da25-0x103-
|
|
|
CARRIAGE LOCK FOR A 16" CLAUSING LATHE MACHINIST PART
CARRIAGE LOCK FOR A 16" CLAUSING LATHE IF YOU WOULD LIKE DIFFERENT PIC'S JUST ASK. IF YOU HAVE ANY QUESTIONS JUST ASK. I WILL NEED YOUR E-MAIL ADDRESS TO SEED YOU PIC'S. SAME DAY OR NEXT DAY SHIPPING ON THIS ITEM! PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS THANKS FOR LOOKING PAYMENT IS DUE IN THREE DAYS I look forward to a positive transaction. And leaving/receiving positive feedback at the conclusion of this auction. I will do my best to work with you(the buyer) on any and all issues. PLEASE CONTACT ME with any questions, if you would like additional pictures, and before leaving negative feedback. My feedback is important to me and I WORK WITH YOU towards a positive purchase. Thank you. And happy bidding. PLEASE READ MY FEEDBACK AND BID WITH CONFIDENCE. I WILL COMBINE SHIPPING WHEN POSSIBLE. IF YOU PURCHASE MORE ... moreTHAN ONE OF MY ITEMS PLEASE GIVE ME A HEADS UP EBAY DOESN'T ALWAYS SHOW IT. NOTE I TRY TO SHIP MY SATURDAY& SUNDAY AUCTIONS ON MONDAY IF I RECEIVE YOUR PAYMENT. THANKS IN ADVANCE FOR YOUR BUSINESS NJ RESIDENTS ARE CHARGED 7% SALES TAX. I DO SHIP INTERNATIONALLY I HAVE MANY PARTS FOR AN ATLAS/ CRAFTSMAN 6" 10" LATHE. I HAVEN'T HAD TIME TO POST THEM. IF YOU NEED SOMETHING AND DON'T SEE IT POSTED PLEASE ASK ME. I ALSO HAVE MANY PARTS FOR A 9" SOUTH BEND LATHE. I HAVEN'T HAD TIME TO POST THEM. DROP ME AN E-MAIL WITH WHAT YOUR LOOKING FOR. PLEASE VIEW MY NEW EBAY STORE FOR ALL OF MY LISTED ITEMS
|
|
|
CLAUSING-COLCHESTER ENGINE LATHE 15" X 40" "WILL SHIP ITEM"
15" x 40" cc. CLAUSING-COLCHESTER ENGINE LATHE 700 REAR PLEASANT STREET* NORWOOD. MA 02062* 781-440-0983* 781-769-9486 FAX E-MAIL MACHUSED@AOL.COM CLAUSING-COLCHESTER ENGINE LATHE 15" X 40" S/N 6/0015/08560 MACHINE EQUIPPED WITH: 3& 4 JAW CHUCK. STEADY& FOLLOW REST, ALORIS TOOL HOLDER, CARRIAGE STOP THREAD CHASING DIAL. CHANGE GEARS. ELECTRICS: 220/3/60/5 HP F.O.B. NORWOOD. MA"NOTE WE WILL SHIP THIS ITEM" NOTE THIS ITEM NOT AVAILABLE UNTIL MARCH 25.2014"
|
|
|
Hardinge 1A Collet 1/8" - South Bend, Hardinge, Craftsman, Delta, Clausing
This is a lathe collet that is interchangeable with the 3C series. It is in exceptional condition except for the two(2) ID markings on the face as seen in the photo. It does not affect the proper use of this collet.
|
|
|
Original,Craftsman,Clausing Metal Lathe Carriage Tool Holder Bracket
Original.Craftsman,Clausing Metal Lathe Carriage Tool Holder Bracket Search Hello, I am parting out a vintage Craftsman/Clausing metal lathe. I am no expert on parts. Equipment or use, so please email with any questions and I'll do my best. The serial plate on the lathe bed. Which is about 5' long, is marked 101-27440. This auction is for a tool holder clamp as shown in good shape. Check out my other auctions. Thank you for looking! Please email me if you have any questions. Check out photos below. Photos are part of the description. Be sure to enlarge them twice for highest level of detail. California residents will pay Ca. Sales Tax. I will combine shipping on multiple purchases when possible. Wait for me to invoice you. ALL ITEMS PAID FOR ON FRIDAY WILL BE SHIPPED THE FOLLOWING MONDAY.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf54%3E-144bc94478a-0xf6-
|
|
|
4 Jaw Chuck D1-8 Cam 16 Turnado turn nado 17 inch Clausing colchester lathe
This is off a Clausing Colchester 17 inch lathe 16 diameter with a D1-8 cam lock. 1 inch pins on 6-3/4 center distance. This chuck does need some cleaning however. If you have a need for a chuck off of a Clausing colchester l7 inch lathe. This lathe was a parts machine. Thank you for your Business! Will ship Freight! God Bless! RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf%60%60%3E-144bd1abbff-0x112-
|
|
|
3 Jaw Chuck D1-8 Cam 15-3/4 Turnado turn nado 17 inch Clausing colchester lathe
This is a South Bend Turn nado 15-3/4 diameter with a D1-8 cam lock. 1 inch pins on 6-3/4 center distance. This chuck does need some cleaning however. If you have a need for a chuck off of a South bend Turn nado l7 inch lathe. This lathe was dropped on its face some parts were destroyed however many good ones left. Thank you for your Business! Will ship Freight! God Bless! RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*4a24%60%3C%3E-144bd1abbea-0xf9-
|
|
|
Clausing Colchester 17 inch Lathe guard or backsplash 107 inches long
This is a Clausing Colchester 17" Lathe backsplash or chip guard. It is used but overall in nice shape. Will ship. Thank you for your Business!
|
|
|
Clausing Colchester 17 inch motor 10 hp Dual Voltage
This is a Clausing Colchester 17 inch motor. It is used but is in working condition. Shiping: $115.00.
|
|
|
Clausing Colchester 17" Lathe Lead Screw
This is a Lead Screw for a Clausing Colchester 17" Lathe. It is used but is in good condition. Call if you have any questions about the screw or about shipping. It is about 107-5/8" total length. Shipping: Freight LOC:Wonder Warehouse
|
|
|
Clausing Colchester 15 inch Lathe half nut
This is a Clausing Colchester 15 inch Set of Half nuts If you are looking for a set of half nuts then you probably know how expensive they can be here is a set that looks to be in nice shape. Thank you for your Business! SHIPPING: $12.00 God Bless!
|
|
|
Clausing Kalamazoo Fully Automatic 12" Horizontal band saw new approx 2005
NORTHERN MACHINERY SALES INC 12 F JOHN RD SUTTON MA 01590 508-581-9922 WHERE THE METAL MEETS THE TOOLS! BUY.SELL,TRADE, REBUILD,REPAIR,NEW AND USED SHEET METAL& STEEL FABRICATING MACHINERY CLAUSING FULLY AUTOMATIC 12" HORIZONTAL BAND SAW MODEL ~~~ C12AX we are well below market value on this machine as we are with most! MANUFACTURERES SUGGESTED REPLACEMENT VALUE~~~~~~ 23.000.00 12" 305mm) Automatic Bandsaw Untitled Document Standard Features… Full or semi-automatic operation Infinitely variable blade speeds Hydraulic down feed Automatic height setting feature Auto shutoff at end of material or after preset number of cuts Blade breakage/stoppage switch 110v control circuit Overload protection Recirculating coolant system Shuttle vise 12" 305mm) Automatic Bandsaw. Specifications Model, Motor, 5 Hp(3.75 kw) 230/460v 3ph* ... moreHydraulic Pump Motor, 1 Hp(75 kw) Hydraulic Oil Capacity, 6.5 gallons(25 liters) Band Wheel Dia. 16" 406mm) Blade Speeds(Variable speed) 89/262 inf variable. Blade Size, 1.25"x.042"x12'6" 32x1x3810mm) Coolant, Recirculating. Coolant Capacity, 10 gallons(39 liters) 90° Cutting Capacity, Round, 11.8" Rectangular, 11.8" x 12.6" 90 deg. 7.9" x 14.2" 200 x 360mm) Bundle Cutting Width, 6.5" to 10" 165 to 254mm) Bundle Cutting Height, 2" to 8" 51 to 203mm) Feed Length/Index, 15.75" 400mm) Max.Feed(9 times) 141.75" 3600 mm) Length 76.5" 1943 mm) Width, 76.5" 1943 mm) Height(head-down) 57" 1449 mm) Height(head-up) 73" 1854 mm) Bed Height, 26" 660 mm) Net Weight, 3.090 lbs(1388 kg) Shipping Weight, 3.400 lbs(1542 kg) We will ship machine anywhere within usa at prevailing rates skidded please call or email for freight rate. we are not responsible for freight damage.You are responsible for freight claims due to shipping damages when and if they occur. we will gladly load the machine onto your truck if you would like to pick up. we make every effort to ensure machines are shipped prop
|
|
|
Original, Craftsman, Clausing, Metal Lathe Countershaft Pulley & Bracket,No res!
Original. Craftsman, Clausing, Metal Lathe Contershaft Pulley& Bracket, No res! Search Hello, I am parting out a vintage Craftsman/Clausing metal lathe. I am no expert on parts. Equipment or use, so please email with any questions and I'll do my best. The serial plate on the lathe bed. Which is about 5' long, is marked 101-27440. This auction is for a very nice countershaft set-up as shown. Great looking vintage handle. Check out my other auctions. Thank you for looking! Please email me if you have any questions. Check out photos below. Photos are part of the description. Be sure to enlarge them twice for highest level of detail. California residents will pay Ca. Sales Tax. I will combine shipping on multiple purchases when possible. Wait for me to invoice you. ALL ITEMS PAID FOR ON FRIDAY WILL BE SHIPPED THE FOLLOWING MONDAY
|
|
|
Craftsman,Clausing, Metal Lathe Quick Adjust Motor Mount 6" Bolt & Chrome Knob
Craftsman.Clausing, Metal Lathe Quick Adjust Motor Mount 6" Bolt& Chrome Knob Search Hello, I am parting out a vintage Craftsman/Clausing metal lathe. I am no expert on parts. Equipment or use, so please email with any questions and I'll do my best. The serial plate on the lathe bed. Which is about 5' long, is marked 101-27440. This auction is for a 6" long quick adjust motor mount bolt with vintage chrome handle. Check out my other auctions. Thank you for looking! Please email me if you have any questions. Check out photos below. Photos are part of the description. Be sure to enlarge them twice for highest level of detail. California residents will pay Ca. Sales Tax. I will combine shipping on multiple purchases when possible. Wait for me to invoice you. ALL ITEMS PAID FOR ON FRIDAY WILL BE SHIPPED THE FOLLOWING MONDAY
|
|
|
Original, Craftsman,Clausing, Metal Lathe Quick Change Gear Ratio Plate,Tag,Mint
Original. Craftsman,Clausing, Metal Lathe Quick Change Gear Ratio Plate,Tag,Mint Search Hello, I am parting out a vintage Craftsman/Clausing metal lathe. I am no expert on parts. Equipment or use, so please email with any questions and I'll do my best. The serial plate on the lathe bed. Which is about 5' long, is marked 101-27440. This auction is for an unmounted. Like new, mint minus condition, info tag for thread ratios as shown. usually mounted on quick change gear cover. Like new with small dings. Blemishes from storage, very minor. Check out my other auctions. Thank you for looking! Please email me if you have any questions. Check out photos below. Photos are part of the description. Be sure to enlarge them twice for highest level of detail. California residents will pay Ca. Sales Tax. I will combine shipping on multiple purchases ... morewhen possible. Wait for me to invoice you. ALL ITEMS PAID FOR ON FRIDAY WILL BE SHIPPED THE FOLLOWING MONDAY
|
|
|
CLAUSING EQUIPTOP CSG-3A618 HYDRAULIC SURFACE GRINDER PRESCISION GRINDER FREEFR8
CLAUSING SURFACE GRINDING.ACHINE IN GREAT COSMETIC AND WORKING SHAPE. FREE FREIGHT WITH BUY IT NOW ONLY! SEE MY OTHER MACHINES I WILL BE LISTING INCLUDING(MAZAK VERTICAL MILL V-15N W/ WAMU6 CONTROLS, BRIDGEPORT. BAND SAWS, DO ALL, INGERSOLL COMPRESSOR, METAL BAND SAW, ETC. PLEASE ASK ANY QUESTIONS PRIOR TO BIDDING/BUYING. FREE FREIGHT TO COMMERCIAL ADDRESS ONLY. Posted with
|
|
|
CLAUSING colchester Feed bar for 17" Lathe
This is s feed screw for Clausing 17" lathe. It comes with nut. Used. But still ok. Any questions, call. It is about 106-1/4" long. Shipping: Freight LOC:Wonder Warehouse;1?RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2B%3E%3B1%3F-144be5b2875-0x10c-
|
|
|
Clausing Colchester 15 inch fiberglass end cover
This is a Clausing Colchester 15 If you have a need for end Guard off of a Clausing colchester l5 inch lathe here is one not perfect but in fair shape. Thank you for your Business! Shipping: $45.00 God Bless!
|
|
|
Clausing Colchester 17 inch lathe bed
This is a Clausing colchester Lathe Bed If you have a need for a Great lathe Bed this one is in Very nice shape. Thank you for your Business! Shipping: Freight God Bless!
|
|
|
Clausing Colchester 17 inch fiberglass end cover
This is a Clausing Colchester 17 If you have a need for end Guard off of a Clausing colchester l7 inch lathe here is one not perfect but in fair shape. Thank you for your Business! Shipping: $45.00 God Bless!
|
|
|
Craftsman,Clausing,Atlas,Metal Lathe Bed Tailstock,Tool Clamp & Bolt,Part # 9-7
Craftsman.Clausing,Atlas,Metal Lathe Bed Tailstock,Tool Clamp& Bolt,Part# 9-7 Search Hello, I am parting out a vintage Craftsman/Clausing metal lathe. I am no expert on parts. Equipment or use, so please email with any questions and I'll do my best. The serial plate on the lathe bed. Which is 54" long, is marked 101-27440. The plate is marked SEARS ROEBUCK, the bed is marked ATLAS, and the manual that came with lathe is marked CLAUSING. This auction is for a bed rail clamp part number 9- 7 that measures 2 1/4" x 3 1/4" along with bolt as shown. Nice used condition Check out my other auctions. Thank you for looking! Please email me if you have any questions. Check out photos below. Photos are part of the description. Be sure to enlarge them twice for highest level of detail. California residents will pay Ca. Sales Tax. ... moreI will combine shipping on multiple purchases when possible. Wait for me to invoice you. ALL ITEMS PAID FOR ON FRIDAY WILL BE SHIPPED THE FOLLOWING MONDAY
|
|
|
Horton 2 Jaw 12" Chuck Model 2212 No.36 Clausing? Metal Lathe Machinist Taper Mt
12" Horton 2 jaw metal lathe chuck. I believe it came off a Clausing but I could be wrong. Mount has taper inside with threads outside. See pics and if you need more details please give an exact description of what you need me to measure. Jaws move simultaneously. I apologize if this does not apply to you but due to multiple ridiculous offers: Please do NOT send an offer requesting free shipping as it does not tell me where you live or the cost and I will NOT except it. It tells you what the shipping is and that is what you are expected to pay. I am already going to lose money on the shipping bc it does not take into account me having to make a crate and the extra cut that ebay takes. NO it will not fit in a Flat Rate Box if you thought that it should it is a larger chuck then you are thinking.
|
|
|
12" D1-6 Four Jaw Lathe Chuck 4-jaw USA made? pin back Monarch clausing leblond
Up for auction a large 12" 4jaw lathe chuck with integral D1-6 mount. I believe this is probably an older piece. USA made probably but I can't find a name on it. I can find 12" D1-6, 562, and markings indicating the diameter size of each groove but no manufacturer's name. It is a fair bit grimy and it feels like there is some back and forth slop in at least a couple of the jaws; but this is a used piece and should probably have some good use left in it. It looks well built and has two piece jaws and other nice features. LOCAL PICKUP ONLY! Unless you want to arrange freight at your own time/ expense if paid for up front.
|
|
|
Clausing lathe 5900 series-Armstrong Boring bar Holder- w/1/2" bar and wrench
Armstrong Boring Bar toolpost/ holder for Clausing compounds- accepts 3/8-3/4" bars-comes with one 1/2" sleeved bar and sleeve wrench
|
|
|
Atlas Lathe / Clausing Lathe Boring bar holder with bars Williams # 080
080 Williams boring bar holder for Atlas Clausing lathes- Comes with 6 bars- Holder is in nice shape-Fits smaller toolposts-measures 5/16 x 3/4"
|
|
|
Clausing colchester 21 Follow rest for 21" Lathe
For sale is a Follow rest for 21" Lathe. Shipping will be $30.00 Thanks for looking and God Bless!
|
|
|
Clausing 5900 series lathe -Williams Threading tool-NEW
Williams Threading tool for Clausing and other Lathes-Appears new-in excellent condition a;06d2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28%3Ea%3B06d2-144be60d460-0xfd-
|
|
|
Clausing 5900 Series Lathe Royal Collet closer with sleeve and nose protector
Nice Royal collet closer with nose protector and spindle sleeve-Fits Clausing 5900 Series lathes-
|
|
|
Clausing Lathe #9 Williams Sleeved boring bar-With wrench-Super Nice
Like new-may be new-9( 3/4" Williams Sleeve Bar-With wrench-Very nice complete piece
|
|
|
5-C Collet Nose Piece and Head Stock Center from 15" Lathe, ?Clausing - LeBlond?
A local company is in the process of relocating its machine shop facility. As a result. Any surplus-duplicate-unused tools will be designated for disposition. These items will be from either the machine shop or the prototype shop, and they all appear to be in good condition. Sale is final so please feel free to ask any questions that you might have and I will do my best to provide an accurate answer. Offered here is a 5-C Collet Nose piece and a Head Stock Center which I was told came from one of the 15" Lathes. The lathes I saw in the shop were Clausings and LeBlond. But I am not sure which lathe these were from. To help determine if these will fit your spindle, I measure the taper as 2.490" on the large diameter and 2.345" on the small diameter(measured over a length of about 3-1/8" Both of these appear to have been ... moreunused, and as a result of sitting in storage have developed some areas of light rust. They could use a clean and polish, and should be ready to be put into service.
|
|
|
LEBLOND REGAL 19"X 80" SERVOSHIFT ENGINE LATHE SOUTHBEND MONARCH CLAUSING JET
HERE IS A NICE RUNNING Leblond REGAL SERVO SHIFT ENGINE LATHE. THIS LATHE CAN BE INSPECTED UNDER POWER IN MPLS MN. TO SET UP AN INSPECTION. PLEASE CALL JIM@ 952-931-7974. THANK YOU. NOTE: THIS MACHINE IS TIGHT AND THE WAYS ARE IN NICE SHAPE. SPINDLE SOUNDS GREAT. GENERAL SPECIFICATIONS: Leblond Regal Servo Shift Model 19E7 Serial 5E 559 new in 1978 Swing Over Bed: 19.25” Swing Over Cross: 12.25” Distance Between Centers: 80” Spindle Speeds: 12) 25-1800 RPM Spindle Through Hole: 1.76” Spindle Nose: L-1 Spindle Taper: 4 Morse Taper Length of Bed: 99” Width of Bed: 14.375” Depth of Bed: 21.125” Carriage Length: 21” Cross Slide Travel: 9.625” Compound Travel: 4.375” Feed Changes: 48 Feed Range inch per rev. 0023” to.132” Thread Changes: 48 Threads per inch. Range: 2 to 112 Leadscrew Dia. Threads per inch: 1.1875”4 Tailstock Spindle Dia. 2.43” ... moreTailstock Spindle Taper: 2 Morse Taper Tailstock Spindle Travel: 7” Complete With: Taper Attachment Coolant Motor: 7.7 Hp Weight 5500# PRICE LOADED ON YOUR TRUCK.$12.500.00 SOLD AS IS AS INSPECTED
|
|
|
Clausing Startrite 30RWS Vert Bandsaw w/ 30" Throat Sliding Table Variable Speed
CLAUSING STARTRITE 30RWS VERTICAL BANDSAW W/ SLIDING TABLE& 30” THROAT Description: Up for sale is a Clausing Startrite 30RWS Vertical Bandsaw. This vertical band saw is in good working and operating condition. It features a manual rack& pinion sliding table. A 30” throat depth, and variable speeds(2 speeds: adjustable 60-360fpm& 600-3600fpm) This machine requires 3 phase power to operate. STANDARD EQUIPMENT· 2 H.P. TEFC 3-phase motor with dual range transmission· Magnetic starter with 110v. control circuit and overload protection· Built-in blade welder. Shear, and flash grinder· 2-way tilting tables. 45° right and 15°left· Blade guide inserts. ¼” ½” ½” blade· Blade tension indicator· Built-in 110v receptacle· Speed and blade selector dial· Locking bandwheel ... moredoors· Table trunnion and guide wrench· Operation and parts manual SPECIFICATIONS MANUFACTURER CLASUING STARTRITE SERIES RW MODEL 30RWS SERIAL 152175 YEAR 1996 NET WEIGHT 925LBS DIMENSIONS 66” X 25” X 72”H FOR MORE INFORMATION PLEASE CALL GARY AT(510) 453-0513 FOR MORE INFORMATION PLEASE CALL GARY ARAGON AT 510 453-0513 LOCATED AT 601 ALADDIN AVENUE. SAN LEANDRO. CALIFORNIA 94577* TERMS AND CONDITIONS* SALES Your bid is a contract. Place a bid only if you are serious about buying the item. If you are the winning bidder. You will enter into a legally binding contract to purchase the item. If the seller is unable to establish contact with the winning bidder within three days of the end of the auction, or if payment isn’t received within three days of the invoice date, item may be offered to the next highest bidder or re-listed at the sellers’ discretion. Please do NOT pay until you are invoiced! PAYMENT TERMS Gary S. Aragon. LLC accepts ATM and these major credit cards: Visa, MasterCard, Discover. Buyers may call us at 510 453-0513 with credit card information. You can also use PayPal. PayPal payments should be sent to garysaragon(at) comcast.net. CALIFORNIA STATE SALES
|
|
|
Clausing 1768 Variable Speed Drill Press, Excellent Condition
Offering a used. Clausing 1768 Variable Speed Drill Press in Excellent Condition. Check out the pictures. This is a 15" drill. 7-1/2" from column to center of chuck. 3/4 hp 115/230 volt. Current wired for 115 volt, single phase. 1/2" chuck Large production table measures 21-1/2" x 15-1/2" and has a solid top with coolant trough. Table has a raising and lowering devise so you don't have to muscle it around. Machine does NOT appear to have been heavily used and is very clean. I have only vacuumed off the table and blown some dust off it. Drill is offered As-Is. Where is with no warranty. I will ship this tool by freight. The buyer is responsible for all details related to the shipment. I will help where I can. This drill is also available locally for sale and listing may end early if sold locally. i can be reached ... moreat 760-5zero5-7242 if you have questions or would like to inspect the drill. Keith I prefer cash payment upon pick-up. Paypal also accepted.
|
|
|
Clausing Milling machine 8540 Horizontal Mill Gearbox Assembly
Clausing Milling machine 8540 Horizontal Mill Gearbox Assembly Comes with pulleys as shown
|
|
|
Vintage Clausing Model 3100 10" Table Saw with Fence
InterSchola is retained by education institutions and local public agencies nationwide to bring valuable surplus inventory to the eBay marketplace. Items listed by InterSchola have been declared surplus by the appropriate education or public agency institution in accordance with state regulations regarding the sale of surplus assets and are listed for sale as a service to these organizations. Net proceeds from the sale of these items are returned to the school districts or local public agencies to support their budgets. See our page to learn more about InterSchola. Please also visit the InterSchola Store to see other assets for sale! Vintage Clausing Model 3100 10" Table Saw with Fence Item Description: This is a vintage Clausing 10" table saw with fence retired from a school woodshop program. to view our current offerings of school ... moredistrict/public agency surplus items we have for sale on eBay. Click images for larger view(ISID: 38777) nbsp, nbsp, Model: 3110, nbsp, nbsp, Accessories: Only the accessories or parts described in this listing are included with this item. No other accessories. Including other items or accessories that may be pictured, are guaranteed to be included. nbsp, nbsp, Condition: This item is used and sold as-is. Due to the location. This item was NOT TESTED for operation. Item may need service and/or parts to make operational. nbsp, nbsp, Pickup Logistics and Handling: Forklift may be available on site to assist in loading on pickup day. However. NO loading dock is available at this location. Buyer will be responsible for all equipment. Tools, personnel and transportation necessary for loading and removal from site. Please contact us for additional information before bidding. nbsp, nbsp, Sales Tax: PLEASE NOTE: If you pay immediately at the end of auction using the eBay payment method please include the 8.0% sales tax or wait for the InterSchola invoice. Which will include the sales tax and should arrive shortly after auction end. Failure to include tax on your payment. U
|
|
|
Clausing Colchester Lathe Open End Wrench 15/16 and 1 5/16 england vintage
Clausing Colchester Lathe Open End Wrench 15/16 and 1 5/16 made in england slightly bowed as seen in pictures sold as is as pictured.
|
|
|
20" CLAUSING Variable Speed Drill Press Model 2285
20" CLAUSING Variable Speed Drill Press Model 2285 MODEL 2285- Serial No. 507240 ITEM# 11252. $1000.00 CAPACITY- CAST IRON. 1-1/4" DRILLS TO CENTER OF CIRCLE. 20" IN DIAMETER OVERALL SIZE OF TABLE. NO TABLE AVAILABLE WORKING SURFACE OF TABLE. NO TABLE AVAILABLE SPINDLE TAPER. 3 MORSE SPINDLE TRAVEL. 6-1/2" MAXIMUM DISTANCE SPINDLE TO TABLE. 25-7/16" SPINDLE SPEEDS TWO RANGES INFINITELY VARIABLE: LOW RANGE.150- 1.000 RPM HIGH RANGE. 300- 2.000 RPM APPROXIMATE WEIGHT. 300 LBS EQUIPPED WITH: MANUALLY OPERATED RACK AND PINION TYPE MECHANISM FOR RAISING/LOWERING OF DRILLING HEAD ON COLUMN. DRILL HEAD SWIVELS ON BALL RACE IN SUPPORT COLLAR. 3/4- 1.5 H.P. 3/60/220 VOLT TWO-SPEED SPINDLE DRIVE MOTOR w/ DRUM SWITCH CONTROL The information above was taken from a machine of similar model and age- Please call to verify specifications. ... moreFor easier shipping. Press was removed from a 10 1/2 ft. Cast iron table.
|
|
|
BEAUTIFUL RUNNING 20" CLAUSING VARI SPEED DRILL PRESS WITH PRODUCTION TABLE
PERFECT RUNNING CONDITION. THIS CAME OUT OF THE TOOLROOM AT THE POLORAID PLANT IN NEW BEDFORD MASSACHUSETTS. ITS A CLAUSING VARI SPEED DRILL PRESS. 20" MODEL WITH THE 24" X 40" PRODUCTION TABLE. MODEL# 2287 SERIAL# 51302B. THIS HAS A# 3 MORSE TAPER SPINDLE WITH A LIKE BRAND NEW 3/4" JACOBS BALL BEARING SUPER CHUCK. VARIABLE SPINDLE SPEEDS FROM 150-2000 RPM. ITS GOT A 3/4 HP-1 1/2 HP 440 3PHASE 2 SPEED MOTOR. IT HAS 6 1/2" OF QUILL TRAVEL WITH 26" HEIGHT FROM THE SPINDLE TO TOP OF THE TABLE. THE CRANK UP HEAD WORKS REAL SMOOTH. I HAD IT RUNNING HERE AND ITS PERFECT THRU ALL THE VARI SPEEDS ON THE SPINDLE. EMAIL WITH QUESTIONS. BUYER PAYS SHIPPING OR COME PICK IT UP HERE. SKIDDING AND CRATING EXTRA FOR OVER THE ROAD FREIGHT. CUSTOM SKID $125.00 AND A FULL BOXING JOB $275.00 EXTRA. THANKS KENNY RUMFORD SUPPLY& ... moreMACHINERY COMPANY INC. 263 PINE STREET SEEKONK. MA. 02771 TEL# 1-800-592-5912 SERVING THE MACHINE TOOL INDUSTRY FOR 55 YEARS
|
|
|
Poland D1-6 8" 3 Jaw Lathe Chuck mount pin back monarch clausing leblond three
Up for auction is an 8" 3-jaw chuck with D1-6 integral mount. No chuck wrench included. I was able to turn it with a ratchet and it seemed to move smooth and well without much slop. The chuck does have 2 damaged wrench spots as pictured, the third might be a little rounded out as well. The face of the chuck looks pretty good- can't see a brand name- but says made in Poland. The taper mount looks nice and smooth, the chuck does have built up dirt/ old grease in nooks here and there, plus some rust on the jaws as pictured. Review pictures carefully, the jaws will have to be unbolted for shipment- which is free!
|
|
|
5c collet closer draw bar chuck for small metal lathe Atlas Clausing etc.
This is a 5C collet draw bar for a small metal lathe. I don't know what lathe this was made for. The main tube is 1-3/8" OD and 18-3/8" long to the base of the first shoulder. Let me know if you need other measurements.
|
|
|
Clausing Lathe 5900 Series Crossslide Screw Assembly - With Gib / Complete
Complete cross slide assembly for 5900 series Clausing lathe-Includes dials. Screw,nut, gib-set screw on dial is not the correct one- Posted with.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf%60%60%3E-144d0513c93-0x10e-
|
|
|
Clausing Lathe 5900 Series Handwheel Collet Closer-Protector / Sleeve / Collets
Very nice handwheel collet closer complete with nose protector and spindle sleeve-Comes with 48 collets-1/16 th" through 1" in 1/32 increments- also includes 7/64th through 29/64th-About as close to a complete set as you can get-Used collets are Royal with a couple of/ Buck/ Hardinge-the few new are from Victor Questions? call or text 502-330-2242 Posted with
|
|
|
CUSHMAN 5" LATHE CHUCK SOUTHBEND LOGAN COLCHESTER CLAUSING ATLAS
THE CUSHMAN/SOUTH BEND 5" THREE-SELFCENTERING CHUCK. By The Cushman Chuck CO. Hartford.Conn USA. Extra set of Jaws Comes with a removable back mounting plate of 1 1/2"8 Cuck is in good used condition. Check out my!
|
|
|
Clausing Lathe 5938- 1hp 3ph Nice / clean-36"
Nice used Clausing 5938-serial# 530426-New belts. Oil sight glasses, crossslide screw and nut- Fairly clean machine-Step pulley-1 hp 3 ph-comes with Union 3 Jaw chuck-lantern tool post, live/ dead centers, drill chuck and spanner wrench- Questions call or text 5023302242
|
|
|
VERY NICE CLAUSING COLCHESTER LATHE 10" X 24" 1800 RPM AUTO FEED SINGLE PHASE
VERY NICE CLAUSING COLCHESTER LATHE 10" X 24" 1800 RPM WITH CABINET STAND This is a fixed auction for a Very Nice Clausing Colchester Lathe. Item specifics: Swing: 10" Center to center: 24" Spindle Speed: 1800RPM Chuck: 6" 3-Jaw with key Single Phase Automatic Feed Dimensions: 60" x 24" x 48" Also features a Aloris tool post(Model AX) Features a cabinet on lathe stand that opens for easy storage of components. Unit was pulled from an operational work environment and is in great working condition. Lathe is exactly as pictured. We will happily load your truck at no charge. Or assist in planning the most economical delivery. The shipping costs we list in our description are for the 48 contiguous USA states only. Shipping will be recalculated for buyers in Hawaii. Alaska or outside the United States once ... morewe have received your shipping address. Buyers are responsible for their Country's custom fees. We always combine shipping to give you the lowest possible cost. We have competitive rates for our always welcomed international bidders. We pride ourselves on our customer service. And we want to make this eBay transaction as smooth as possible. Please feel free to call us between 9:00-5:00 EST Monday-Friday at 800 826 3433 if you have any questions.
|
|
|
CLAUSING COLCHESTER 17" LATHE OPERATION & PARTS MANUAL OLDER ROUND HEAD MODELS
5 DAY AUCTION! CLAUSING COLCHESTER 17" LATHE OPERATION/PARTS MANUAL FOR THE OLDER ROUND HEAD MODEL ONLY 42 PGS. 1965 YOU ARE BIDDING ON ORIGINAL LITERATURE UNLESS OTHERWISE STATED S&H $6.00 PRIORITY MAIL. COMBINED SHIPPING AVAILABLE. PLEASE WAIT TO TO INVOICED FOR MULTIPLE PURCHASES. INTERNATIONAL BIDDING REQUIRES APPROVAL. PHOTOCOPIES ARE NOT AVAILABLE PAYMENT EXPECTED WITHIN 3 BUSINESS DAYS OF AUCTION CLOSE SECOND-CHANCE OFFERS AVAILABLE ON SOME ITEMS
|
|
|
CLAUSING COLCHESTER 15" LATHE OPERATION & PARTS MANUAL OLDER ROUND HEAD MODELS
5 DAY AUCTION! CLAUSING COLCHESTER 15" LATHE OPERATION/PARTS MANUAL FOR THE OLDER ROUND HEAD MODEL ONLY 38 PGS. 1964 YOU ARE BIDDING ON ORIGINAL LITERATURE UNLESS OTHERWISE STATED S&H $6.00 PRIORITY MAIL. COMBINED SHIPPING AVAILABLE. PLEASE WAIT TO TO INVOICED FOR MULTIPLE PURCHASES. INTERNATIONAL BIDDING REQUIRES APPROVAL. PHOTOCOPIES ARE NOT AVAILABLE PAYMENT EXPECTED WITHIN 3 BUSINESS DAYS OF AUCTION CLOSE SECOND-CHANCE OFFERS AVAILABLE ON SOME ITEMS
|
|