|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Condition: Used Location: Monticello, United States Plasma cutter and Machine torch. Swift Cut CNC Plasma Table. I have cut 3/8" plate with this machine. Worked well. I used this until I bought a bigger ... moretable.
Buy It Now
Free Shipping Condition: New Location: Pottstown, United States The Eastwood Versa-Cut 4' X 4' CNC PLASMA TABLE is the perfect way to get the features of a professional CNC Plasma Table at a hobbyist price. The Eastwood ... moreVersa-Cut 40 CNC Plasma Cutter was specifically designed to connect directly to, and work flawlessly with this Plasma Table.
Buy It Now
Free Shipping Condition: New Location: Columbus, United States The gantry is designed to operate on 2x4 tubing. (14 gauge). This assures strong support and longevity. Y Axis: The Y axis (running front to back) has ... morecarriages much deeper than many standard carriages.
Buy It Now
$6.16 Shipping Condition: New Location: Henderson, United States CNC Plasma table fluid mix. Makes 200 gallons of fluid. Directions: Mix one spoon for every 5 gallons of clean freshwater. For optimal setup use a 40 ... moregallon clean trash can and a circulation pump attached to a 8 foot length of hose and finger clamp.
Buy It Now
Condition: Used Location: Worcester, United States 2023 Linclon Electric Torchmate 4800 - 125 Quote #1484. USED - -2023 Lincoln Electric Torchmate 4800 Plasma Cutting System. 4 x 8 CNC Plasma Cutting Table. ... moreRockfish Machinery has financing options available.
Buy It Now
Condition: Used Location: Brooklyn, United States With its high-quality construction and advanced features, this plasma cutter is perfect for professionals and DIY enthusiasts alike.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. CNC Vertical Machining Centers. CNC ... moreLathes. CNC Plasmas. Kinetic K5200XMC 10' x 100' CNC Plasma w/ Oxy & Drill (2018).
Buy It Now
Condition: Used Location: Stone Mountain, United States Power Source: Hypertherm Powermax 85 Sync. Hypertherm Powermax 85 Sync, Scribe Tool, Spare Parts. 3D Printers Air Compressors Air Cooling & Heating Equip. ... moreBenders Boring Mills Broaches Chemical & Processing Equip.
Buy It Now
$50.00 Shipping Condition: New Location: Bend, United States Then seal up the top shelf, add water, along with the included wave break. and now you have the best roll-around water table for your hand held plasma ... morecutter! We also include an adjustable clamp to hold our Plasma Stencils or straight edges.
Buy It Now
Condition: Used Location: Salem, United States Hypertherm HPR260. Multicam 6000 Series Plasma Cutter. 8’ X 20’ Table. Drive System (X, Y Axes). Drive System (Z Axis). X Axis Travel. Rapid Traverse ... moreRate. +/-. 0001".
Buy It Now
$1500.00 Shipping Condition: New Location: Las Vegas, United States The STV CNC® SparX™ Plasma Table Series incorporates high end machine features and capabilities, in a smaller package. Using our high accuracy stepper ... moremotors for speed, control and smooth operation and combining it with ground linear bearings and guide rails results in consistency and speed that is unrivaled in the industry. Additionally, our tables are built tough and designed to easily handle half-inch steel plates (but they can handle more). Made in the USA. Our SparX™ Plasma Table is designed for businesses rooted in auto-repair, industrial manufacturing, agriculture, architecture, and a host of other industries which can all benefit from the business improvements an STV CNC® branded CNC plasma cutting table can bring.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. CNC Vertical Machining Centers. CNC ... moreLathes. CNC Plasmas. Komatsu Rasor KCR-0951 6' x 13' CNC Plasma Cutter.
Buy It Now
$4.47 Shipping Condition: New Location: Johns Island, United States It uses the IPT-40 head, which is a blow-back start, non-high frequency start, similar to what Hypertherm has done for many years. Stay away from high-frequency ... morestart if you are building a CNC plasma table, because it causes electrical interference that can crash the computer running the CNC.
Buy It Now
Condition: Used Location: Cedarburg, United States Model #: HPR 260. Sector Spectrum Gantry Plasma Burn Table. 480V, 3 ph @ 60 Hz. Capacity: 10' x 24'. SPEC'S SUBJECT TO FINAL INSPECTION. S/N: 1140-0603-450-170.
Buy It Now
$57.62 Shipping Condition: Used Location: Topeka, United States This is a used like new Lotus LTP5000D 50 amp plasma cutter. This is a very compact portable unit which makes it very nice to use. Included is everything ... moreyou see pictured with the original box as well.
Buy It Now
Free Shipping Condition: New Location: Pottstown, United States Only plasma cutters with blowback (low frequency) start are permitted. Furthermore this use could invalidate your plasma cutter’s warranty. Reach out ... moreto your plasma cutter’s manufacturer for guidance.
Buy It Now
Condition: Used Location: Stone Mountain, United States Model: Edgemaster. 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. CNC Vertical Machining ... moreCenters. CNC Lathes. CNC Plasmas. Lincoln Torchmate 4800 4' x 8' CNC Cutting Table with FlexCut 125 Amp Plasma.
Buy It Now
$1500.00 Shipping Condition: New Location: Las Vegas, United States The STV CNC® SparX™ Plasma Table Series incorporates high end machine features and capabilities, in a smaller package. Using our high accuracy stepper ... moremotors for speed, control and smooth operation and combining it with ground linear bearings and guide rails results in consistency and speed that is unrivaled in the industry. Additionally, our tables are built tough and designed to easily handle half-inch steel plates (but they can handle more). Made in the USA. Our SparX™ Plasma Table is designed for businesses rooted in auto-repair, industrial manufacturing, agriculture, architecture, and a host of other industries which can all benefit from the business improvements an STV CNC® branded CNC plasma cutting table can bring.
Buy It Now
Condition: Used Location: Stone Mountain, United States Power Source: Hypertherm XPR 300 X-Definition Plasma System. Year: 2021. 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills ... moreBroaches Chemical & Processing Equip. CNC Vertical Machining Centers.
Buy It Now
Condition: Used Location: Stuart, United States | | | |( green and to be as environmentally friendly as possible with our shipping materials. This includes. But is not limited to, reusing shipping supplies ... moreand limiting the amount of plastic used in the packaging process. Froo www.froo.com | Froo Cross Sell. Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application.
Buy It Now
Free Shipping Condition: New Location: Monroe, United States The Tomahawk 625 Plasma Cutter is portable for plasma cutting and gouging on a wide variety of materials including mild steel, stainless steel, aluminum, ... morebrass, and copper. Tomahawk 625 plasma cutting systems are portable enough to carry to any jobsite.
1d 9h 54m 30s 0 bids
$2000.00 Now
$93.66 Shipping Condition: Used Location: Gulfport, United States CNC computer pulled from a plasma cutting table. Item worked when it was pulled it was just replaced with a newer system. I do not have any connectors ... moreto go with it, only the terminal in the picture is included. Item is sold as/is with no warranty expressed or implied.
Buy It Now
$6.00 Shipping Condition: New Location: Middletown, United States This is for Langmuir System with RazorWeld 45 CNC Plasma cutter with Machine Torch ! And Z-Axis Kit. This is NOT the machine its only wire and torch guides ... morethat'll clip in around the tube. Then you clip the torch in and z motor & the limit switch wire.
Buy It Now
$5.95 Shipping Condition: Used Location: Sanford, United States Currently under power and can be tested. Machine is still in use we are just looking to upgrade to a larger cutting surface and downdraft system.
Buy It Now
$1200.00 Shipping Condition: New Location: Las Vegas, United States The STV CNC® SparX™ Plasma Table Series incorporates high end machine features and capabilities, in a smaller package. Using our high accuracy stepper ... moremotors for speed, control and smooth operation and combining it with ground linear bearings and guide rails results in consistency and speed that is unrivaled in the industry. Additionally, our tables are built tough and designed to easily handle half-inch steel plates (but they can handle more). Made in the USA. Our SparX™ Plasma Table is designed for businesses rooted in auto-repair, industrial manufacturing, agriculture, architecture, and a host of other industries which can all benefit from the business improvements an STV CNC® branded CNC plasma cutting table can bring.
Buy It Now
Condition: Used Location: Stone Mountain, United States Model: K5200XMC. Year: 2018. 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. Plasma ... morePower Source: 400amp. CNC Vertical Machining Centers.
4d 10h 54m 6s 0 bids
$14000.00 Now
Condition: Used Location: Bedford, United States 4x8 CNC Plasma Cutting Table Precision Cutting Systems industrial 4x8 cutting table. This is the best built industrial cutting table on the market today ... morefor under $20.000.00. When making your comparisons of our table to the competitors note the individual features! You will not find another manufacturer using our industrial components in their table construction for this price. 4x4 steel tube constructed frame Tapered downdraft tray Replaceable warebar holders Spiked warebars 10" extruded aluminum gantry 3/4" aluminum gantry mounting plates Dual 20mm linear bearing slide system on X and Y axis 1" rack and pinion drive Dual side drive 6" gantry to table clearance(will accomodate up to 3/4" plate) 2.5" cable carrier Linear ball screw torch head assembly Oiling system for all linear bearings Industrial control panel using Mach3 motion control software Machine can be ordered with capacative sensing torch height control for HVAC use. Or an IHS arc voltage torch height control system.
$3000.00 Shipping Condition: New Location: Houston, United States Fast Cut Icon Elite Series CNC Plasma Cutting Table General Info: Stock# JG-141005 Machine Name: Fast Cut Icon Elite Series CNC Plasma Cutting Table Condition: ... moreUsed. Good Brand: Fast Cut CNC Model: Icon Elite Series Year: 2010 Location: GA Specifications: Icon Elite Series CNC Plasma has a 5x10' table with a 3" total working envelope on the z axis. The machine is equipped with 570oz-in hybrid step motors and a dual drive linear guide system. The drive system runs on helical rack and pinions on the x and y with a enclosed ball screw on the z. The max cut speed is 400 ipm with a rapid traverse speed of 500 ipm. The Icon Elite Series CNC Plasma utilizes a A120 Thermal Dynamics Cutmaster plasma cutter. The cutter has a cutting capacity up to 3/4" The setup also comes with a Ingersoll Rand D25IN air dryer. The Icon Elite Series CNC Plasma also includes the controller which has TurboCAD. Sheet CAM and Mach III CAD/CAM software included. Additional Info: The Plasma Table is currently under power and can be tested. Seller Contact Information: Jamie Gose 404-630-3657 The Equipment Hub. LLC 1380-A Beverage Dr. Stone Mountain. GA 30083 Are you looking for a different machine than the one listed? Visit our to see other machinery options. It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week.
Buy It Now
$47.15 Shipping Condition: Used Location: Odessa, United States Hypertherm Duramax Hand Torch Assembly with 50’ plasma torch lead and a 75 degree torch handle. Torch assembly fits Hypertherm Powermax 105. Torch lead ... morehas a 25’ leather sheath to provide protection from burn-throughs and abrasion.
Buy It Now
$5.95 Shipping Condition: Used Location: Columbia, United States ESAB PGC-3 Plasma Gas Control. P/N: 0558008252. Used - functions properly no issues ESAB M3 Plasma System
Buy It Now
$15.45 Shipping Condition: New Location: East Lansing, United States iPTM-80 CNC Plasma Machine Torch head , works for most brand CNC machine or table. Shipped with USPS Priority Package (2 to 3 business days).Any questions ... moreplease feel free to contact us.This torch works for most CNC machines. Reuse your torch cable, only change torch head when it's wear out.
Buy It Now
Condition: Used Location: Brighton, United States (Almost) Complete CNC Plasma Cutter System (Hypertherm + Avid CNC). Hypertherm Powermax 65 with machine and hand-held torches. electronic relay for plasma ... moretrigger. Pickup in Boston, MA. Smooth stepper.
Buy It Now
Condition: Used Location: Seguin, United States You can also save more money and increase productivity by ordering genuine Lincoln Electric® plasma cutting consumables.
Buy It Now
$25.00 Shipping Condition: New Location: Bend, United States The Square Table will sit on top of a Behrens 15.5 gal. square tub that is filled with water, this creates a very economical and effective Plasma Table. ... moreAll of the sparks/slag and most of the smoke is captured with a 5" air gap above the water.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. CNC Vertical Machining Centers. CNC ... moreLathes. CNC Plasmas. Model: Accu-Kut CNC. Bend-Tech Dragon A400 CNC Tube & Pipe Plasma Cutting Machine (2017).
Buy It Now
Condition: Used Location: Lynn, United States Blue Elephant 5x10 CNC Table with 5x10 Servo Drives. Hypertherm Max 200 Pro Power Supply with Fang Ling F2100B Control. THC F1628D. Works great; runs ... moresmoothly. Everything works just no employees to run it. If bought can be loaded onto buyer's trucks for pick up or freight can be issued. Feel free to contact for any questions. Willing to sell power supply separately or table please contact.
Buy It Now
$400.00 Shipping Condition: New Location: Everton, United States Training & diagnosis is done by Mikogo screen share over the internet. This makes buying a plasma cutting table from Eagle Plasma an easy decision. It’s ... morea robust machine with high-end components that are built into a small machine footprint.
Buy It Now
Free Shipping Condition: Used Location: Mount Dora, United States Pulled off of a working system for a retrofit. Working perfectly upon removal.“Parts are sold “as-is”, without any warranty or returns unless otherwise ... morespecified. Some parts can be tested upon request.
Buy It Now
$950.00 Shipping Condition: New Location: Burnet, United States All PowerEdge Plasma Cutters have 100% Duty Cycle at Full Power! That allows us to maximize capabilities and automate the most complicated aspects of ... moreCNC Plasma Cutting.You don't need any CNC or Plasma Cutting experience!
Buy It Now
$950.00 Shipping Condition: New Location: Burnet, United States All PowerEdge Plasma Cutters have 100% Duty Cycle at Full Power! That allows us to maximize capabilities and automate the most complicated aspects of ... moreCNC Plasma Cutting.You don't need any CNC or Plasma Cutting experience!
Buy It Now
$1500.00 Shipping Condition: New Location: Las Vegas, United States The STV CNC® SparX™ Plasma Table Series incorporates high end machine features and capabilities, in a smaller package. Using our high accuracy stepper ... moremotors for speed, control and smooth operation and combining it with ground linear bearings and guide rails results in consistency and speed that is unrivaled in the industry. Additionally, our tables are built tough and designed to easily handle half-inch steel plates (but they can handle more). Made in the USA. The Hypertherm Powermax45 XP Machine System with a great cut capacity, fast cut speeds and automatic gas adjustment is included in this bundle.
Buy It Now
Condition: Used Location: Oostburg, United States 144” x 72” cutting bed.
Buy It Now
Free Shipping Condition: New Location: Monroe, United States We have been serving the welding industry for over 25 years. We are an award winning Hypertherm Distributor. THE TORCH DOES NOT INCLUDE THE CONSUMABLES ... more. The Duramax machine torch is designed for use with the Powermax 65, 85 and 105 plasma cutting and gouging systems.
Buy It Now
$114.71 Shipping Condition: Used Location: Sharpsburg, United States 2004 Accu-Cut CNC Plasma Cutting Table 6' x 12' Table S/N 0060204.
7d 9h 8m 23s 0 bids
$25000.00 Now
$2000.00 Shipping Condition: Used Location: Spring Lake, United States It is a powerful unit that can handle all types of cutting jobs, from large-scale industrial projects to smaller DIY tasks. Also included is the Bobcad ... moresoftware for plasma and wood cutters. The PT-CUT Master A-120 Automatic Plasma Cutting System (5/8" Production); 220V single phase, 35' cable and the PT-T-5263 20' Cable with Manual SL Torch.
Buy It Now
$40.00 Shipping Condition: New Location: Daly City, United States The small stature and light weight of the cutter indicates that this unit is designed to be a space saver. For those needing more power and portablity ... moreout on the jobsite, this unit will operate off any clean power (5% or less THD) generator capable of producing 10,000 Surge Watts of power.
Buy It Now
Condition: Used Location: San Antonio, United States This is a Torchmate TM3 table. The TM series of tables were sold with all electronics and hardware. You would build your own table and add your plasma ... morecutter. This table is constructed out of heavy duty tube.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. Model: 3400 Heavy. CNC Vertical Machining ... moreCenters. CNC Lathes. CNC Plasmas. Max Positioning Area (X Axis): 190.6″.
Buy It Now
$20.10 Shipping Condition: New – Open box Location: Fort Lauderdale, United States I purchased a new Thermal dynamics 102 Cutmaster for my CNC Plasma table one month ago, I don’t need the hand Torch.
Buy It Now
$67.35 Shipping Condition: Used Location: Canada
Buy It Now
$17.80 Shipping Condition: Used Location: Bucyrus, United States See photos for details. We have over 7+ acres of under roof new and used Industrail Surplus Not limited to the following.
Buy It Now
Free Shipping Condition: New Location: Hicksville, United States Tomahawk 625 plasma cutting systems are portable enough to carry to any jobsite. Hook up the compressed air, grab the torch and start cutting right away. ... moreDue to its reliability and portability, this plasma cutter is ideal for onsite maintenance, small construction sites, HVAC and demolition.
Buy It Now
$20.50 Shipping Condition: Used Location: Bucyrus, United States Hi up for sale is a Hypertherm 120477 Nozzle. See photos for details. Crane Parts, Iron workers, Forklifts, Forks,Ect.Ect.Ect. Lose Ball Bearings,Bearings,Seals,New ... moreGe Floodlights, Chain Hoist, Crane Hoist, Over Head Cranes.
Buy It Now
Free Shipping Condition: Brand New Location: China Keyboard: PCB keyboard. divider by 7 pins socket, links with lifting motor by 5 pins socket. original height before the perforation delay is finished. ... moreThis function is an approximate dynamic perforation function.
Buy It Now
Condition: Used Location: Louisville, United States Cutting Thickness 1/8" to 12" with Oxy Fuel. Oxy-fuel cutting. 55' of Floor Mounted Side Rail. Easy-to-use, feature rich, Windows® interface. Virtual ... moreService puts Service experts one push button away.
Buy It Now
Condition: For parts or not working Location: Fort Lauderdale, United States Thermal Dynamics 5-0075 SL60 Plasma Cutter Spare Parts Kit Cutmaster 52 or 82 Click an Image to Enlarge TD5-0075 Welcome to the Weldfabulous eBay store! ... moreTo make your purchase as simple and easy as possible. Please refer to the store policies listed below. After winning an item in auction or completing a Buy It Now purchase. You have two check-out options: Check-Out Now! Click the at the top of this listing to immediately proceed with our checkout and payment process. Please note that the Pay Now button is ONLY available after winning an auction or completing a Buy It Now purchase. Check-Out Later If you do not choose to Check-Out now. You will be notified by eBay via e-mail that you are the winning bidder. There is no need to contact us to arrange payment. We will automatically send you an e-mail within three hours of an auction closing. Our message will contain a link to our simple and secure checkout system, where you will be able to quickly and conveniently pay for your purchase. Payment We accept the following forms of payment. PayPal Visa. MasterCard, American Express, and Discover credit card payments through eBay Checkout Sales Tax Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 For shipment to Minnesota. Wisconsin, and Iowa addresses, we are required by State law to collect sales tax for the appropriate states. Tax rates are as stated below Minnesota: 6.875% Wisconsin: 5.5% Iowa: 7% Normal 0 false false false EN-US X-NONE X-NONE Domestic Shipping Continental United States UPS Ground and USPS Priority Mail are our standard shipping methods within the Continental US. We offer free shipping on all items except cylinders. UPS Ground requires 1 to 6 business days to arrive after leaving our facility and is fully traceable in route. We cannot ship large packages to PO Boxes so please be sure to provide us with a physical shipping address. For specific small. Low value items such as beanies, gloves, jackets, etc. we do offer US Postal Service Priority Mail for shipments within the C
Buy It Now
Free Shipping Condition: New Location: Las Vegas, United States The STV CNC® SparX™ Plasma Table Series incorporates high end machine features and capabilities, in a smaller package. Using our high accuracy stepper ... moremotors for speed, control and smooth operation and combining it with ground linear bearings and guide rails results in consistency and speed that is unrivaled in the industry. Additionally, our tables are built tough and designed to easily handle half-inch steel plates (but they can handle more). Made in the USA. The Hypertherm Powermax45 XP Machine System with a great cut capacity, fast cut speeds and automatic gas adjustment is included in this bundle.
Buy It Now
Free Shipping Condition: New Location: Houston, United States Our plans will allow you to build a plasma pattern copier.It make exact size duplicates of whatever you can trace. Or follow with the stylus. You can ... morecut out shapes just like a cnc plasma table only on a smaller scale, and without having to program. Cut shilouettes, cut out alphabets, great for metal art. Our plans include a templa t e that can be scaled to make any size plasma duplicator you want. Small or large. At 100% it will give you a cutting area of approximately 8 inches x 24 inches. Videos viewable on our site. Plans-Template& photos are available as a download More Info at Plasma.Fix-Er-Up.Com Have a problem building it. We will help thru our Helpdesk! Powered by The free listing tool. List your items fast and easy and manage your active items. ao5pta.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bisk%3Eao5pta-13e0ff33504-0xfa-
Buy It Now
$90.00 Shipping Condition: New Location: East Lansing, United States 120Amps Plasma Cutter , 3 phase 440V , CNC table ready , PowerEdge120 include:1. 1pc Remote control and remote cable.2. 1pc Air regulator.3. 1pc Hose.4. ... more1pc Ground clamp with cable.5. 10pcs plasma torch consumables.6. 1pc 26ft long cable , PE120C CNC plasma torch(straight torch for CNC table).7. 1pc CNC cable , 26ft.8. 1-Handheld cable PE120H,26ft long.This machine isa blowback,non-HF machie. CNC table ready for our GOFABCNC table.If you have other brand CNC table , please contact us for the CNC cable to control cutter and hook it up to your CNC table.5 years warranty.
Buy It Now
$9.75 Shipping Condition: New Location: Bulgaria DaniTHC7SDP is Suitable for use with Breakout boards non supporting THC( like USB or LAN serial communication). DaniTHC7SDP(Dir/Pulse) is a stand alone ... moredevice. Dani THC7SDP (Direction/Pulse input /output interface) (SD- Speed /Direction) tipe.
|
|
|
|
WELDING WELD PLASMA CUTTER 96-001 CUTTING TORCH HEAD MAYBE FOR PLASMA TABLE
This listing is for a plasma part. We will be liquidating alot of equipment in the next week or so. So check back for other great deals. Make: Unknown Model: 96-001 Description: plasma cutting part You will receive the exact item pictured. Powered by The free listing tool. List your items fast and easy and manage your active items. 4ffc.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*77%3E4ffc-13e6389d6fa-0xf2-
|
|
|
CNC Plasma table-Tracker Nitro 4x4
4x4 cutting area-Automatic Torch Height Control-No Plasma Cutter-Integrated Onboard Computer System-ProTable Command Center-Corel Design Software-Sigmanest Optimization Software-Dropped" Linear Rail Design- Dropped linear rail system locates the gantry rail's below the cutting deck surface to ensure safe& easy loading from any side of the ProTable. Rails are nestled inside the massive main beams of the table frame for further protection Does Not include a Plasma Torch. Requires a Machine Torch for Operation.
|
|
|
CNC Plasma Table PlasmaCam
Used CNC PlasmaCam Plasma Table Model 98Z Serial#2546 Works great. Includes plasma table. Cnc controls and lower rolling table. The custom lower table allows the plasma table to mount on top of the table and be easily moved around on its casters. Additionally it has a mount for the plasma machine and a small table above the plasma mount. Above the plasma mount is a swing arm that allows you to mount a lap top on top and easily swing it out of the way when not in use. Very nice feature. Includes original manual and cd's/program plus a back up manual for the shop. We just purchased a waterjet and need the space. All you need is to hook up your desk top or lap top computer and plasma machine and your ready to start cutting precision parts! Call or email us with any questions. Local pickup preferred in San Diego as the lower table is fully ... morewelded and costly to ship. Thanks for looking!
|
|
|
Hypertherm Plasma with Table 11’ 6” Wide x 27’ Long x 5' Tall
Hypertherm Plasma with Table FOR SALE Machine is in good working condition and used every day. We are re-arranging our facility and need to make room. Since we currently have two plasma machines. Shipping to be taken care of by purchaser. No warranty machine to be sold as is. If you would like an inspection please let us know. YouTube Clips of Hypertherm: this one is the plasma cutting. this one is of the controller. Four AXESCNC& MAX 200 Plasma Cutter Cutting Area = 10' x 24' Overall Footprint = 11'6" x 27' x 5' EDGE II CNC 2 Servo Axes 10.4” Color LCD Monitor 2-Optically Isolated Serial Ports(RS232/RS422) 3.5” 1.44 MB Floppy Disk Auxiliary Quad Power Supply 40.0 GB Hard disk 256 MB RAM 2.4 GHZ Intel Celeron Processor Sensor THC ASSY-0087. Industrial Grade 12“ Low Profile Slide100 Watt AC Servo Motor 3rd& ... more4 th Servo Axis SensorTHC Electronics PneumaticTorch Breakaway Mount Part#MECO-0107 HyperCad 2-D Drawing Englishor Metric Units Partor Sheet Viewing Capabilities Scale.Rotate or Mirror parts Repeatand Copy Shape Move/ModifyLead-in/Lead-out AddChamfers. Fillets, notches FullPart Cutting simulation on Screen HyperNest True Shape Nesting Software AutoNest Capability SingleTorch Operation 300W DrivePackage YaskawaAC Drives CNCCables 3 x 25’ 3x 10 Meter Motor Cable 3x 10 Meter Encoder Cable Gear Box Thompson Gear Box MAX 200 Plasma Max 200 Power Supply(200 AMP) 4– OXY-FUELTorch’s Water Table 11’ 6” Wide x 27’ Long x 40” Tall Air Rise Table.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf52%3E-13e937540c6-0xff-
|
|
|
Vicon CNC Plasma Table
This table is up for sale again due to prior buyer not paying for the item. Used Vicon plasma table. Table is 5' x 10' cutting area. Fabricators model with automatic torch height control($4800.00 option) Vintage is 1998. Software was updated at one time yet has not received any new updates over the past 6 years. Table is in used condition and shows the wear and tear a machine of this vintage would be. This table is still under power and available to see running. Currently using Vicon cutting software, can cut from.DWG files, use rectangular and round HVAC fitting files or draw your own parts in drawing program. We have burned parts up to 1/2" thick HR without any problems and severed 5/8" thick HR. Plasma machine"package" will include the computer system, torch height controls, 100 AMP Hypertherm power source and ... moretorch, extra consumables and manuals are included in the sale. We are upgrading and going to a 8' x 20' table and no longer need this table. We would include all of the exhaust system(including blower) with the system if requested. This is a ready to run machine with controls at an exceptional price. Buyer pays for shipping, we will load onto flatbed at no cost.
|
|
|
CNC Plasma table, runs on Mach 3, shop made
For Sale: Shop made CNC plasma table. Computer is Windows XP, table runs on Mach 3. Table is 5 ft by 8 ft. You can view the table working on this youtube video link if you have an iphone. There is not a plasma cutter with this table just the table. Computer with flat screen and the motor controller. The table and the medical computer cart are on casters so you can easily move it in your shop. This unit is being sold as is. Local pick up preferred, or I will work with your shipper on loading.
|
|
|
plasma table. 9 X 12
Good used table With computerized cutting options Posted with
|
|
|
lockformer plasma table 5x10 Model 1000-B ~SHEET METAL GUYS LOOK!!!
NORTHERN MACHINERY SALES INC, BUY. SELL TRADE, NEW AND USED SHEET METAL AND STEEL FABRICATION MACHINERY 12 F JOHN RD SUTTON MA 01590 WHERE THE METAL MEETS THE TOOLS! 508-581-9922 Used Defined As: Preowned. Not re-conditioned, imperfections possible. ALL MACHINERY IS SOLD AS IS WHERE IS* PREOWNED-LOCKFORMER HVAC PLASMA SYSTEM 5X10 MODEL-1000B M.S.R.P- 46.500.00 5X10 CUTTING ENVELOPE TOUCH SCREEN ONBOARD CONTROLLER HYPERTHERM POWERMAX 1000 PLASMA SUPPLY 3/8" CAPACITY 3 PHASE POWER. BELT DRIVE SYSTEM GULLWING DESIGNPNEUMATIC TORCH LIFTER SEALED DC SERVO BRUSHLESS MOTOR MORE THAN 900 PRELOADED SHAPES PREVIEW ONSCREEN FITTING PART ROTATION SCALING SHAPE REPEAT ACCELLERATION CONTROL 40X CD ROM ENCODER FEEDBACK POSITIONING SYSTEM TURNING VANE CUTTING SUPER PART SEGMENTING COMPLETE HOLE CUTTING ABILITIES SOFTWARE WILL HOLD TO 10.000 SHAPES 586 ... moreCPU 17" COLOR MONITOR VGA 30 GIG HARDWARE TABLE WILL SUPPORT UP TO 5X10X1/2" PLATE 1-1000 IPM MAXIMUM TRAVERSE SPEEDS WINDOWS BASED OPERATING SYSTEM COMPLETE HVAC SOFTWARE AND HARDWARE FOR PROCESSING DUCT WORK INCLUDED SYSTEM INCLUDES PLENUM YOU WILL NEED TO VENTILATE IT AT 3500CFM DOWN DRAFT TABLE DESIGN 100% USA BUILT LOCKFORMER PRE-INSTALLATION DATA WILL BE PROVIDED WITH SYSTEM WHEN IT SHIPS. FREE FREIGHT IS INCLUDED TO LOWER 48 ONLY@ BUY IT NOW PRICE! WE WILL SHIP IT FLAT BED TARPED.YOU MUST OFFLOAD SYSTEM FOR OFFERS THAT ARE ACCEPTED FOR LESS THAN THE ASKING PRICE FREIGHT WILL BE AT PREVAILING RATES.
|
|
|
Plasma Cam Cutting Table and Software
Plasma Cam Cutting Table(Includes all software necessary to run) Machine used less than 10 hours. Stored inside For any information call: 605) 515-0516. Ask for Alvin Eisenbraun. Any questions on authenticity call: Plasma Cam(719) 676-2700.
|
|
|
Torchmate 2 CNC Plasma Tabel 5ftx12ft water table
This is a 2009 Torchmate 2 CNC Plasma system with a 5 ft x 12 ft water table. Powered by a THERMAL DYNAMICS CUTMASTER A60 PLASMA CUTTER WITH 25' MACHINE TORCH. Torchmate still offers free unlimited tech support for this table. Feel free to call them anytime. This system cost over $25.000 new and is still the current model. It is under power and we can demo it at our shop during the week. It is 100% operational. Please give us some advance notice. It includes 5x12 gantry Torchmate auto height control Thermal Dynamics Cutmaster A60(can cut up to 1" 80 amps) signal(208/230) or 3 phase(240/480) Torchmate 2 signal generator Torchmate 2 motor driver 5x12 adjustable height water table cost $7500 to build the table alone Dell PC configured and loaded with torchmate software and 1000's of vector drawings ready to be cut Hand held remote ... morecontrol Laser dot for aligning sheets We can load on your flat bed truck or trailer. No shipping is included. It is highly recommenned that the buyer make argangements to properly pack this system. Payment due when auction is completed. Machine must be moved within 14 days of auction competition or item will be considered abandoned and no refunds will be made. We need the space in the building. Here's a video of this table cutting. BTW the water is green because it has plasma quench added it the water to reduce corrosion.
|
|
|
Table for Plasma, Laser or Fluid Oxygen Cutters
Hede Nielsen Table for Plasma. Laser or Fluid Oxygen Cutter. In fine condition with no dents. Approximate 300 x 300 cm. Shipping: Please contact us for shipping information NOTE: Buyers resident inside the European Union: Private persons and companies without a valid VAT number ARE being charged the national VAT tax in Denmark. Which are 25% added to the sales price. Companies with a valid VAT number ARE NOT being charged the national VAT tax in Denmark. Which are 25% added to the sales price. REMEMBER TO SEND VALID VAT NUMBER. Buyers resident outside the European Union: Private persons and companies ARE NOT being charged the national VAT tax in Denmark. Which is 25% added to the sales price. Buyers resident in Denmark- Private persons and companies ARE being charged the national VAT tax in Denmark. Which are 25% added to the sales price. ... morePlease contact us for if you have any questions Click Here. Double your traffic. Get Vendio Gallery- Now FREE! RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf54%3E-13f6ca28f82-0xfa-
|
|
|
ESAB Silhouette 500 CNC Plasma cutting table W/ PCM1125 & HL-90 & Burny 2.5RS
THIS IS A NICE CLEAN 2001-02 CNC PLASMA FROM A LOCAL HS SHOP CLASS. THE COMPLETE SET-UP IS AS FOLLOWS: 1- ESAB SILHOUETTE 500 TABLE AND TRACK SYSTEM(24X24) EXPANDABLE IN 24" INCRAMENTS CNC GAS/PLASMA Sn. 00-BUR-2.5-5126 1- ESAB PCM 1125 PLASMA CUTTER(1Ph) W/ 25' TORCH ASSEMBLY Sn.PA-J006053 1- BURNY 2.5RS CONTROLLER Sn.17257-01-01 1- LINTROL HL-90 TRACKING UNIT Sn.13632 3- MANUALS ONE EACH ESAB. BURNY AND LINTROL AS YOU CAN SEE FROM THE PHOTOS THIS IS A WORKING UNIT. SHOWN USING THE LINTRON TRACKING UNIT TO COPY A DRAWING. THE SCHOOL SOLD ME THIS UNIT WORKING, BUT I HAVEN'T BEEN ABLE TO SPEND THE TIME LEARNING THE BURNY MANUAL. 300 PAGES) THE CURRENT TABLE IS ABOUT 4' X4' WITH 24"X24" USEABLE TRACKING AREA. THIS COULD BE EXTENDED TO 24"X36" WITH THE ADDITION OF A FOOT OF DRIVE TOOTH TRACK. ESAB HAS ... moreEXTENSION KITS FOR THE TRACK& TABLE IN 2 FT INCRAMENTS. BURNY SUPPORTS THE 2.5RS AND HAS UPGRADES AVAILABLE. THE LINTROL HL-90 IS STILL THE INDUSTRY STANDARD. PHOTOS SHOW US CUTTING 1/4" MATERIAL IN AN DETAILED PATTEERN. WE ALSO USED IT TO CUT SOME REPEATABLE 1" THICK PARTS NO PROBLEM. JUST A LITTLE SLOWER SPEED. THIS LISTING IS FOR LOCAL PICK-UP. IF YOU REQUIRE SHIPPING WE WILL BREAKDOWN THE UNIT AND BOX IT ON A PALLET FOR $125.00. YOU'LL STILL PAY ALL SHIPPING COSTS FROM 80477. 4' X4' X2' PALLET BOX-300 + Lbs) LOCAL PICK-UP OR SALE TO COLORADO RESIDENTS REQUIRES WE COLLECT 3.9% SALES TAX. SHIPPMENTS OUT OF STATE HAVE NO SALES TAX. WE WILL SHIP ONLY TO THE LOWER 48 STATES! NO HI.AK OR CANADA/MEXICO OR OTHER.
|
|
|
PlasmaCam CNC Cutting Table, Plasma Cutter, Air Compressor Package Ready to USE!
Up for auction! Looking for a great way to bring in revenue to your metal business. This is it! We have not had the time to use this system the way we intended and are ready to sell. This system works great and is very productive! Please let us know if you have any questions! All components are in very good working condition. Buy as a package and save! All you need is metal and electricity and you're ready. BONUS: PC with Windows XP and PlasmaCam software installed! Paid $16.800 for this entire package 2+ years ago. Local pickup or free delivery within 250 miles of zip 24382. Over 250 miles. We will make arrangements with buyer! Pick up or delivery! Payment must be made in full at end of auction. SEE DETAILS BELOW AND PLEASE EMAIL OR CALL WITH QUESTIONS- 276-620-6537. This Plasma Automated Cutting system has all the components needed ... morefor you to start cutting metal today! This auction comes with the following: 1. PlasmaCAM Model DHC2 cutting system. With transferable software. 2. HyperTherm PowerMax 1250 plasma cutter. 3. Kobolt 80 Gallon 155 Psi Oil-filled industrial air compressor. PlasmaCAM Model DHC2 cutting system. Includes an interactive. Video-based instruction manual that installs on your computer. PlasmaCAM is a CNC cutting table that is able to cut precise metal shapes in a flash. Moving parts are rigid. Without excessive weight. This enhances performance. Providing fine. Detailed cutting and high productivity through fast cut speeds. Rugged CNC plasma cutting machine with strong drive train is built to perform in heavy production. Drive train and electronics are protected from plasma dust. And guide rollers move unobstructed. Durable steel frame with integral cutting grate. Cutting grate precisely aligns to the frame. With stops that perfectly Position material for indexing and utilizing sheet edges in long parts. Wide plasma cutting torch compatibility with a simple. Easy-to-install interface. Works with common hand torch(machine torch not needed) Video-based instruction manual is easy to navi
|
|
|
Lockformer CNC Plasma Cutting Table
Lockformer Vulcan 2000 CNC Plasma cutting table. 5' x 10' sheet size. Hypertherm HT40C plasma power source. 40 amps. CNC Controller:SI Tech bit driver. Model:2005 Table is in very good condition and can be seen under power in Ohio.
|
|
|
Plasma Cam CNC Table-Less than 12 hrs usage-4x4
NO RESERVE* This auction is for a used Plasma Cam Inc. 4x4 CNC Table with no more than 12hrs. of usage on it. It was originally bought new for $9.000.00 and is no longer needed in the shop. It comes with an extra height motor, an extra torch mount. 2 instructional CDs, and a full manual. I will disassemble and palletize this machine and take it to one of our local truck freight terminals for $125(plus freight) or will hold for local pick up. Please contact me if you have any questions. 336.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E336-13fbc9cd0f9-0x104-
|
|
|
C&G Challenger Plasma Oxygen Cutting System Burny 3 Plasma Table 5’ x 7’
TR Loc: FLR-654 Posted: DS USED C&G Challenger Plasma Oxygen Cutting System Burny 3 Plasma Table 5’ x 7’ Plasma and Oxy-Fuel Burning and Cutting Table Syst, C& G Systems Challenger Plasma Oxy-Fuel Cutting System ~ Water Table: 5ft x 7ft ~ Thermal Dynamics MERLIN 1000 Power Supply ~ Burny 3 CNC Control ~ Arrow Air Dryer ~ Boa 2.0 USB to Serial Port Converter ~ Desk Top Computer w/AutoCad LT& SheetCam G-Code Nesting Software The BOA 2.0 is the latest generation of memory adapter products from Valley Cutting Systems. The BOA or Basic Omniport Adapter is designed to work with the Burny 3 and Burny 5 Controller. Allows for G-Code download directly into the Burny via a Memory Stick. SheetCam is a low cost but feature packed CAM package. Converts DXF drawings to G-Code. Also is a nesting program. As mention. Included is a Desk Top computer ... morethat has the AutoCAD LT and SheetCam software installed on it. All reasonable offers will be considered. Can be seen running under power. By appointment Pictures are of the actual unit. Condition Good used condition. We have used this machine and it is good working order. Please review pictures and request additional info. If required. before bidding. SHIPPING Prefer Local Pick-Up… but. Can get estimate for Freight if necessary. We’ve supplied pic’s for your inspection and review. Call or email with questions or additional info. Contact Info Toll Road Truck and Trailer 841 North Bedford Street East Bridgewater. MA 02333 Office: 508-378-3931 Fax: 508-378-3366 SHIPPING DETAILS All items sold are shipped FOB our East Bridgewater. MA location, unless otherwise noted. The actual shipping cost to be determined and calculated based on your location. Since each item's and each customer's shipping needs are unique, shipping costs and methods will vary by item and customer. Shipping details will be configured at time of purchase and verified with the customer before delivery. For the purpose of obtaining a shipping estimate,
|
|
|
THERMAL DYNAMICS PLASMA MACHINE TORCH FOR CNC OR TABLE CUTTING SL100 7-5215
UP FOR AUCTION IS A THERMAL DYNAMICS MACHINE TORCH MODEL SL100 7-5215 I BOUGHT A CUTMASTER 51 FROM A BUDDY AND IT HAS VERY LITTLE USE. PLANNED TO USE IT WITH A TABLE OR CNC PROGRAM AND ENDED UP GETTING A BIGGER UNIT. I NEED TO GET THE REGULAR TORCH SETUP AND HAVE NO USE FOR THIS TORCH. THIS TORCH FITS ON CUTMASTER MODELS 51. 52, 81, 82 AND 101,102 and 151, 152 WITH THE SCREW IN PLUG. IF YOU HAVE ANY QUESTIONS OR WOULD LIKE TO MAKE AN OFFER PLEASE CONTACT ME THROUGH EBAY OR CALL 386-316-3822. THANKS
|
|
|
BUG-O 6150 PROGRAMMABLE PLASMA CUTTER BURNING TABLE SHAPE CUTTING MACHINE
BUG-O 6150 PROGRAMMABLE PLASMA CUTTER BURNING TABLE SHAPE CUTTING MACHINE Includes: Bug-O 6150 Programmable Plasma Cutter Shape Cutting Machine Thermal Dynamics PakMaster 100XL Plasma Cutter w/ Machine Torch(S/N: 022929A191301D; Input: 208-460V. 1/3 PH, 72-38A(1 PH) 36-20A(3PH) 15-90A adjustable output) Machine Plasma Torch Burning Table in Plasma Cabinet Prewired 440V Distribution Boxes Dayton 6" Bench Grinder SECOND PLASMA CUTTER(SHOWN IN PICTURE) IS AVAILABLE FOR OPTIONAL FEE AND INCLUDES HAND PLASMA TORCH WITH OFFSET WH Features The Bug-O 6150 Shape Machine is an easy to use 2-axis machine which you can program to run any contour or pattern for both welding or cutting applications. A handheld terminal supplied with the machine is used to program the required shape and operation sequence. Other functions besides moves can be programmed. ... moreSuch as repeats, starts, stops, delays, and rapid traverse. 10 programs can be stored in machine memory at any one time. An optional computer software program is available(through Bug-O) For any IBM compatible computer. With this program you can select pre-programmed shapes or create your own custom shapes, and store any number of them on disk. Selected shapes can then be downloaded to the machine as needed. The Programmable Shape Machine is compact and lightweight and can be easily carried throughout your facility. It is held in position with either powerful permanent magnets or vacuum cups. Depending on the work material. This enables you to take the machine to the work, which will help reduce your material handling. The Programmable Shape Machine is a two-axis machine that runs on a track and carries a torch on a motorized cross-arm. It can be used for flame or plasma cutting. Or welding, of a variety of shapes which are programmed and stored in memory. The machine has storage capacity in memory for 10 different programmed shapes. At any time, one of these shape numbers is selected to be active, and will stay selected even when the power is shut off, and turned back
|
|
|
MAKINO CNC TABLE PLASMA ROUTER ---ULTRA HEAVY
MAKINO CNC TABLE MAKINO BUILT THIS AS CNC TOOL STORAGE BALL SCREWS FRAME WHICH WEIGHS ESTIMATED 2500 LBS REPEATABLE MOTION OF 0.001 INCH END USER MUST ADD SERVO MOTORS DRIVES CONTROL SYSTEM I WILL LOAD ON OPEN TRAILER AT NO CHARGE MOTION ENVELOPE 4 FT BY 6.5 FEET OVERALL DIMENSIONS 3 FT HIGH BY 6 FEET DEEP BY 9 FEET THIS UNIT MADE TO STAND UP ALSO
|
|
|
CNC plasma Vulcan II PCM Hydefinition Plasma Cutting System 60" x 240" Table
Dust collector included(Torit Model DFT 2-8 7.5 hp)
|
|
|
2012 MultiCam V Series 204 CNC Plasma Hypertherm Powermax 85 60x120 inch table
MultiCam V Series 5x10 CNC Plasma Model: V-204-P Machine Voltage: 220V 1 Phase Year: December 2012 See all specifications below. Late 2012 model MultiCam CNC Plasma! FUNCTIONAL GUARANTEE. WE DO NOT SELL MACHINES THAT DO NOT RUN! 100% positive feedback! This late model 2012 V series plasma is a rare find. Less than a year old this machine is in excellent condition. With this being a current model you can refer to the MultiCam website for more detailed information and pictures of the MultiCam V Series CNC Plasma. MultiCam innovations in CNC plasma systems start with the EZ Control material library. EZ Control sets all cut parameters automatically. Yielding extremely consistent cut quality. This MultiCam CNC Plasma comes with the MultiCam EZ hand-held controller. Which is one of the easiest to learn CNC interfaces in the world. Machine Specifications: ... more60"x120" work area Value Series Keypad Interface 220V 1Phase Hypertherm Powermax 85 amp Plasma System with 35' torch lead Automatic Torch Height System Rapid Shape 2D Digitizing Interface 1k/3k/5k Contact Pro Tech Machinery for more details! Available options: Full line of EnRoute 5 Cad/Cam Software available. On-Site Training and Setup available. Material Current(amps) Metric unit Imperial unit Thickness(mm) Production cut speed* mm/min) Thickness(inches) Production cut speed* ipm) Mild steel, 45 85 85 85 85, 3 6 12 20 25, 4900 4400 1600 680 450, 10 GA 1/4 1/2 3/4 1, 164 160 56 29 17, Stainless steel, 85 85 85 85, 6 8 12 20, 4900 3050 1400 570, 1/4 3/8 1/2 3/4, 164 80 48 24, Aluminum, 85 85 85 85, 6 8 12 20, 4900 3470 1930 880, 1/4 3/8 1/2 3/4, 172 104 68 37, Production cut speeds are the result of Hypertherm's laboratory testing. Production speeds are approximately 80% of maximum. For optimum cut quality. Cutting speeds may vary based on different cutting applications. Refer to the operator manual for more details. While we do not offer extended warranties on the sale of used equipment we will guarantee that all major functions of this machine wi
|
|
|
Plasma Cutting Table, Torchmate, 5' x 10'
Torchmate plasma cutting table. 5' x 10' Includes water table. Cutmaster A-80. Computer, monitor, software. Barely used. Looks like new.
|
|
|
PLASMA TABLE SHOP SABRE HIGH DEFINITION PLASMA TABLE
2011 SHOP SABRE SHOPMASTER PRO 10 WITH HYPERTHERM HPR130XD HI-DEFINITION PLASMA POWER SOURCE MICROSYSTEMS OPERATING SOFTWARE. CAD DESIGN. VECTORING, KERF COMPENSATION AND TRUE SHAPE NESTING. LIMIT SWITCHES-1 ON EACH AXIS-X.Y& Z. EMERGENCY STOP SWITCH-FRONT MOUNTED ON CNC TABLE. TORCH HEIGHT CONTROL FOR PLASMA CUTTER W/AUTOMATIC TOUCH OFF. M-PORT FOR PLASMA TORCH START/STOP. M-PORT FOR PLASMA TORCH SENSOR. SHOPMASTER PRO 5' X 10' WATER SLAT TABLE W/ADJUSTABLE WATER TANK& WELD STOPS. Z-PLATE MOUNTING BRACKET FOR PLASMA MACHINE TORCH HEAD. SHOPSABRE COMPUTER. 55 GALLON PLASMA DEFENSE. LASER SIGHT. METAL ENGRAVER PEN.
|
|
|
Dynatorch Plasma Table
Selling our used Dynatorch 4222 Plasma Table. It was in 100% working condition when it was removed to make way for a laser cutter. It is now in storage waiting for a new home. Here is a link to a video of it running; Shipping will need to be arranged by buyer. We have loading docks and a forklift.
|
|
|
CNC Plasma Cutter,CYBERMATION, HVAC SOFTWARE, ESAB, Plasma Table, Hypertherm
Model– Cybermation 2200( GXAC 600) Serial– H70124 Specifications: Table Size 79” W x 176” L Maximum X Travel 73” Maximum Y Travel 163” Table Height 34” Equipped With: NO PLASMA Office Computer System with SCO Cybermation HVAC Software Downdraft Table MACHINE IS SOLD AS IS LOADED AS ONE PIECE WITH PC AND CONTROLS BANDED TO TOP OF TABLE. SOLD WITH NO RETURN OR REFUND, WAS UP AND RUNNING IN LOCAL SHOP AND THEY PURCHASED A NEW MACHINE AND KEPT THE POWER SUPPLY FOR HAN D APPLICATIONS. SHIPMENT: THIS WILL BE AN OVER WIDTH LOAD UNLESS DIS-ASSEMBLED! WILL DIS-ASSEMBLE AND BAND ON SKID TO SIT ON TABLE FOR $500.00 EXTRA
|
|
|
Linde CM-250 Plasma 6'x10' cutting table downdraft
1986 Linde Plasma duct cutter single 6'x10'cutting table. East Coast duct fitting software. Operates fine as is. located in Ipswich Ma.
|
|
|
Torchmate 2 4' x 4' CNC Plasma Table
Torchmate 2 4' x 4' CNC Plasma Table-Arv Volt Height Control with 25' cable set-Thermal Dynamics Cutmaster 120A 208-230/460V SL100 Auto-Machine torch with 25' cable/ with Router attachment-Includes Torchmate CAD/CAM software-Torchmate gantry system made of 3" square extruded aluminum. Complete bolt together kit. All manuals and documents included. Machine is 2 years old. Original Price: $15.865 g.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bjw%60hquvg%3Eg-1420205f65c-0xf4-
|
|
|
Messer - MG Systems CNC plasma table w/ dual Hypertherm HPR-400XD
Selling a used Messer(MG Systems) model TMC-4512 CNC plasma table. Built new in 2001, completely retrofitted in 2010 with(2) new Hypertherm HPR-400XD, Hydefinition plasmas(400 amp) new lifters, new Hypertherm EdgePro control, 12' of X cut capacity(cross travel) by 21' of length travel.in plant, under power, running.can pierce and cut 2" thick mild steel.located in NE Kansas, approximately one hour from Kansas City airport.water table shown in photos included.email with questions or call Don at 913-558-2121.payment via wire transfer.please note that this a large machine, and would require a dedicated truck to haul it, so, disregard the shipping info section.
|
|
|
Lockformer Automated Plasma Table Vulcan 3100D
GLADWINMACHINERY.COM USED 5' X 10' LOCKFORMER Stock No. UK7388-159(General Specifications& Additional Information shown is subject to verification/inspection) ONE OF THE LARGEST SUPPLIERS OF NEW& USED FABRICATION EQUIPMENT IN THE UNITED STATES General Specifications: Type: Plasma Cutting System Model No. Vulcan 3100D Table: 5'x10' Serial No. PCM1006 Additional Information: Includes Hypertherm Hydefinition HD-1070 Plasma(S/N 78-0206) Sold As Is. Installation not included. Please contact me for additional info. And other payment methods. We strongly encourage personal inspection of all pieces of used equipment. Terms& Conditions: If you have any questions regarding either this proposal or any other fabricating equipment, please feel free to contact us at mnsales@gladwinmachinery.com. The proposed prices DO NOT include ... morefreight, rigging, hydraulic fluid, installation, start-up, training, or electrical hook-up, unless otherwise stated. Price DOES NOT include state or federal taxes, if applicable. Proposed machinery may not meet all specific federal, state or local codes. Any necessary changes to conform to code compliance, including, but not limited to, special construction, electrical, hydraulic or pneumatic, is the sole responsibility of the customer. All sales are subject to standard Gladwin Machinery terms. TERMS: Cash or Cashier’s Check with order, and all equipment is FOB on floor from sold location, unless otherwise stated. All equipment is subject to prior sale and is exclusive of any government tax. Equipment descriptions are intended only as a guide and their accuracy is not guaranteed. GUARANTEE/CONDITIONS: If any machine guaranteed by us does not prove satisfactory as represented, the purchaser may return(freight prepaid) upon written notification within 30 days from date of shipment and in a condition equivalent as sent to the buyer. We will refund the purchase price in full. This guarantee does not apply to machines sold“as is” machines sold off of customers’ floor, or machine
|
|
|
KOMATSU PLASMA TABLE MODEL # KCR-0951
KOMATSU PLASMA TABLE MODEL# KCR-0951 USED IN WORKING CONDITION.COMES WITH PC.SOFTWARE,AND ADDITIONAL HVAC SOFTWARE. Maximum Cutting Width: 5' Maximum Cutting Length: 10' Thickness Capacity: 062" 500" Mild Steel& Aluminum) 028" 500" Stainless Steel) Minimum Kerf Width: 06" Cutting Speed: 30- 300 IPM* Rapid Traverse Speed: 1.000 IPM* Variable Cutting Current: 3- 90 Amps* Positioning Accuracy: +/ 004" Repeatablity: 002" Pierce Height Accuracy: +/ 015" Bevel Angle: +/ 2 Degrees* Welded Box Beam Construction Approximate Overall Dimensions: 360"x 192"x 90" Posted with
|
|
|
Lockformer Vulcan 2900 plasma table
Vulcan 2900 cnc plasma table. Was in operation till 2011 at which time it was put into storage. Includes Vulcan 2900 table. Hypertherm HT40C plasma, P.C. loaded with vulcan software updated till 2011, Label Printer, Reports Printer, Fiber optics cable, 220v single phase exhaust fan, air dryer and manuals. All you need to start work except air compressor, and ground rods. Can accept Credit cards if you prefer not to use Pypal. Can assist with shipping, but a forklift rental will be required at the buyers expense(approx $200)
|
|
|
CNC 16'x6' Plasma Cutting Table w/Hypertherm max 100 power supply & torch
CNC 16'x6' Plasma Cutting Table w/Hypertherm max 100 power supply& torch Description cut area 6' x 16' heavy steel I beam construction rack and pinion drive system precision planetary gear drive precision linear rail system AC servo drive system dual side drive gantry heavy duty cable carrier machine input voltage 230/115 maximum plate thickness 3.500 inches 6.500lbs machine weight approx 5.400lbs H-6500 CNC controller with manufacturers shape library. Windows mach motion control X box wireless remote control This package includes Hypertherm max 100 plasma power supply with machine torch. Please contact Scott@ 314-605-4223 with any questions. Or use the ebay message system. About Us, Payment, Shipping, Returns, Contact Us, About Us: FactoryDepot is a worldwide distributor of new& used goods. Our large warehouse is ... morelocated in St. Charles. MO, just outside of St. Louis. We are driven to maintain outstanding customer satisfaction by providing the industry's best quality products. Please visit our website for more information about our quality items. Payment: We gladly accept Paypal. Visa, Mastercard, American Express or Discover as payment. Sales Tax: We are required by the state of Missouri to collect sales tax of 7.45% for orders picked up locally or items shipped to addresses here in the state of Missouri. This does not apply to businesses that are sales tax exempt. Shipping: FedEx/USPS Shipping: FactoryDepot will ship anywhere in the United States and to most international countries. All items are shipped via FedEx Ground. USPS, or Freight. Local pickup is available upon request. Most orders are shipped the following business day. Shipping times vary by location. And can be determined in the listing. FedEx does not ship to PO Boxes. Please provide a physical address for items being shipped FedEx. Freight Shipping: Most freight items(large/over 150lbs) are shipped the following business day after receipt of payment. We only ship freight items to a business address with a loading dock o
|
|
|
Plasma Cam Z-98 Table
This is a Plasma Cam 98-Z table which has all three motors but no controller. Cutting slats are hardly used and the gantry and all parts move smoothly. When I bought table I was told I could not upgrade. I have since been told table can be retrofitted but I have since bought another table. Posted with
|
|
|
Thermal Dynamics CNC Plasma Cutmaster A-80, Torchmate 4'x8' Table w/water table
2011 Thermal Dynamics CNC Plasma Cutmaster A-80. Torchmate 4'X8' Table w/ Water Table This unit is 3 years old and has been used very little. It is in great shape and works like new, Has general wear from use. Feel free to contact us with any questions. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*4a24%60%3C%3E-143a369343a-0xfa-
|
|
|
MG DNC 2.8 HYPERTHERM 72" X 120" HIGH DEFINITION PLASMA TABLE
MG DNC 2.8 HYPERTHERM 72" X 120" HYDEFINITION PLASMA BURN TABLE*NO RESERVE* MUST SELL TO MAKE ROOM FOR NEW WATERJET TABLE TO MEET THE REQUIREMENTS OF RECENT PROJECTS WE HAVE AQUIRED. THIS HAS BEEN A VERY RELIABLE MACHINE AND IS ONLY BEING SOLD SO WE CAN PUT THE WATERJET IN ITS PLACE. WE ARE TAKING DELIVERY OF THE WATERJET IN 3 WEEKS SO THIS MUST BE PICKED UP WITHIN 1 WEEK AFTER CLOSE OF AUCTION SO WE HAVE TIME TO PEPARE THE SITE. BUYER RESPONSIBLE FOR SHIPPING. BUT WE WILL GLADLY LOAD ON YOUR TRUCK WITH OUR LIFTS. THIS MACHINE CUTS GREAT AND WE BURN STAINLESS, CARBON, AND ALUMINUM ALL THE TIME. IT IS CURRENTLY UNDER POWER IF YOU WOULD LIKE TO COME AND OBSERVE IT WHILE CUTTING PARTS. CALL TO MAKE APPOINTMENT 404-245-5296) I CANNOT EMPHASIZE ENOUGH THAT WE WOULD NOT SELL IF WE HAD ROOM TO KEEP BOTH AND THIS WILL MAKE SOMEONE A GREAT ... moreBURN TABLE. WE RUN MTC PRONEST SOFTWARE ON THIS PLASMA TABLE AND OUR LASER CENTER AND IT DOES A GOOD JOB. MTC HAS BEEN BOUGHT BY HYPERTHERM AND WORKS WELL BUT OTHER MAJOR BRANDS OF NESTING SOFTWARE WILL INTEGRATE WITH THIS MACHINE. THE MTC SOFTWARE DOES NOT COME WITH THE MACHINE. THANKS FOR LOOKING! SIZED: 72”X120” SERIAL NUMBER: MM-I-93-2565 DATED: 4/93 POWER SUPPLY: UNIT HOUSES A 70-AMP. 15KW CHOPPER POWER SUPPLY WHICH PRODUCES A CONSTANT CURRENT DC OUTPUT, VARIABLE FROM 15-70 AMPS. IT CONTAINS A MICROPROCESSOR CONTROL PCB WHICH REGULATES ALL OF THE PLASMA SYSTEM FUNCTIONS: START SEQUENCE, MACHINE INTERFACE FUNCTIONS, GAS AND CUT PARAMETERS, AND OFF SEQUENCE. THE POWER SUPPLY ALSO HOUSES THE SUBASSEMLIES REQUIRED TO COOL THE TORCH. THE POWER SUPPLY INTERCONNECTS WITH THE RHF CONSOLE, MACHINE INTERFACE, GAS CONSOLE AND WORK PIECE. MAX OCV: 280 VDC OUTPUT CURRENT: 15-70 AMPS OUTPUT VOLTAGE: 130 VDC
|
|
|
Plasma Cam CNC cutting table 5'x10' with software and Hypertherm Powermax 65
I have lost my shop space and don't have any room for this table anymore. It is in excellent conditon and works great. I cut out a new table grid before disassembling. Everything you need to use is included. Table with computer. Hypertherm Powermax 65 plasma with mechanized torch, machine torch works much better than hand torch on CNC machines) and Plasma Cam's Design Edge software that is so easy to use you won't believe it. Check out a demo video from Plasma cam on their website for more information. This is crated in two crates; one of the crates is 78" long x 36" wide x 18" high and weighs approximately 400lbs and the other crate is 48" long x 24" wide x 30" high and weighs approximately 100lbs. I am willing to ship truck freight or local pick up. Buyer is responsible for cost of shipping. Posted ... morewith
|
|
|
Tracker CNC Nitro 4'x8' Plasma Cutting Table with Hypertherm 1650
Photo is Stock photo. Nitro 4'x8' plasma cutting table for CNC. Brand new cost is 14.000. Included with the table is a Hypertherm Powermax 1650 Brand new cost about 5,000. 20,000 worth of equipment for over 40% off. Fitted with water trays for less mess! Used for only one job that lasted about a week. Call Bob(no later than 8pm) 619-561-1720
|
|
|
Dynatorch CNC Plasma Table 5' x 10' professional system complete
This is a Dynatorch 5' x 10' CNC plasma table system in great working condition. We replaced it with a laser system recently so it needs a new home. This is not a cheapie unit; it is controlled by four heavy-duty stepper motors with 1/4000 inch resolution. The full gantry has a motor at each end for extremely precise and even motion. We've gotten great results from this machine and it is still in excellent condition. It's easy to operate and is still hooked up so we can demo it and even give you some training. Everything you need comes included. The control unit runs off of an HP PC that sits in its own custom rolling cabinet. Amazingly powerful software is included for converting your DXF files to machine drawings with advanced nesting capabilities. Setting your lead-ins and lead-outs, managing materials, tools, etc. The ... moretorch itself is a Hypertherm Powermax 1650 and we've used it with 100 amp tips to cut through 5/8" thick steel(3/4" thick is max) Cuts 1/2" steel very nicely(see the photo of the truck wheel insert) and is very fast on thin gauge steel using 40 amp Fine Cut nozzles. Great results on stainless and aluminum too(see photos examples of stuff we've cut) Electronic auto height control follows irregular or corrugated metal, slopes, etc. and auto collision detection stops the machine instantly if there is a tip-up collision or other problem. A laser cross-hair allow you to start your cuts precisely where you want and you can speed the machine up, slow it down, make adjustments as you cut with either keyboard or joystick control. It comes with extra consumables(electrodes and tips in 40, 60, 80 and 100 amp) and with the extra-fine nozzles you get a kerf of about 0.050" for small precise cuts and designs. This machine works perfectly and needs nothing. It has the trash-catching and exhaust bottom box so you can vent smoke outside if you wish(exhaust fan not included) The Hypertherm torch is a 3-phase 240V unit however if you don't have 3-phase power you can
|
|
|
BURNY REPLICATOR 1000 OPTICAL TRACE PLASMA CUTTING TABLE
YOUR BIDING ON ONE COMPLETE CANTILEVER CUTTING SYSTEM. STARTING WITH THE BURNY OPTICAL TRACE PATTERN CUTTER. A PAPER. POSTER BOARD, OR SHEET METAL PATTERN IS PLACE ON THE TABLE THAN THE OPTICAL EYE IS JOGGED TO THE PATTERN THAN LOCKED ON& STARTED IT WILL FOLLOW THE LINE& THE PLASMA CUTTER USING A REMOTE SWITCH IS TURNED ON TILL THE CUT IS COMPLETED. THAN JOGGED TO THE NEXT LINE& REPEATED TILL ALL THE CUTTING IS COMPLETED. THE BURNING AREA IS AROUND 42" X 57" THIS IS GREAT SOLUTION FOR LOW PRODUCTION OR CUSTOM ONE OFFS. THE CANTILEVER TABLE IS INCLUDED WITH ALL TRACER ELECTRONICS. THE DOWN DRAFT TABLE WHICH IS INCLUDED ACCEPTS A 48" X 60" SHEET. THE ROUND PIPE FROM THE BACK IS(NOT INCLUDED) THERE IS A SQUARE SHEET METAL BOX ON THE BACK WHICH CAN BE ADAPTED FOR YOUR EXHAUST SYSTEM. I USED A EXPLOSION PROOF FAN ... moreWHICH WORKED FINE(NOT INCLUDED) THE PLASMA POWER SOURCE IS INCLUDED, WORKS GOOD FOR 1/4" OR LESS. IT IS A HAND HELD& IT IS CLAMPED INTO HOLDER. IT IS ON A SLIDING BEARING UP& DOWN TO HOLD THE PROPER CLEARANCE BETWEEN TORCH TIP& METAL. THE PICTURE SHOWING THE STACKS OF SHEET METAL IS INCLUDED, AROUND 20& 19 GAUGE. YOU ARE WELCOME TO LOOK AT THE CUTTING SYSTEM IN ACTION AT MY SHOP, I'M LOCATE EAST OF CHARDON, OHIO 44024. EVERY THING WORKS GOOD AS IT SHOULD SERVE THE NEXT OWNER AS WELL IT DID ME. I CAN GET YOU SHIPPING RATE IF YOU PROVIDE A ZIP CODE& HAVE A MEANS TO UNLOAD IT. I WOULD RECOMMEND IT'S NOT A RESIDENTIAL AREA. FREIGHT COMPANY'S WILL CHARGE MORE. THIS SYSTEM HAS A UPGRADE OPTION FOR CNC ADD ON. AS THERE ARE LEADS FROM THE SERVO MOTORS INCLUDED WHEN SYSTEM WAS ORDERED. ALSO AN OXY FUEL OPTION CAN BE ADDED ON FOR THOSE THICK STEEL BURNING JOBS. PLEASE CONSULT FACTORY] BEFORE AUCTION ENDS ABOUT THOSE OPTIONS AS I DON'T HAVE THE TO DO KNOWLEDGE OF THOSE UPGRADES. THANK'S FOR LOOKING.
|
|
|
Plasma Route 5 x 12 Table
Plasma Route 5 X 12 Cutting Table Machine comes with a Hypertherm 1650 Plasma cutter and machine torch Plasma will pierce up to 3/4" and will cut up to 1 1/2" with a edge start Computer cabinet is included I built a little small water table with bar grating greatly reduces the smoke The big compressor is included in this sell the smaller Ingersoll-Rand is not. Once payment has cleared i will deliver this up to 500 miles@ $1.35 per mile
|
|
|
1999 Lockformer Vulcan 2900 Plasma Table
1999 Lockformer Vulcan 2900 5x10 plasma table with Shopdata 2009 nesting/post processing software. Hypertherm Powermax 1000 power source with duramax torch. Pick up at location(commercial warehouse with a loading dock) or will ship for $2.50 per mile. Under power(machine can be seen operating) di,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishhov%3C%3Edi-144549a1892-0x112-
|
|
|
MG Industries Hy Def Plasma Table
This is a 1996 MG Industries 6' x 10' Hy Def Plasma Table. Model MMA-IA. Serial MWP-IA-96-3141. DNC 2.8 Burny Control Model MNF-10206. HD3070 Hypertherm Plasma power unit Serial# 95-43-125-03. Manual Gas Control with air scribe. Will cut 3/4" Stainless steel, 1" Mild Steel, 5/8" Aluminum. There is a good amount of consumables included with the unit. 480V Power required. This unit is sold As-Is Where is. Local Pick up only or you take care to have it shipped. I have some video's I can send out if you have interest in it.
|
|
|
KSK Automatic plasma cutter with table tracer pantograph
KSK Automatic Gas Cutting Machine with heavy duty steel table. Heavy Duty Industrial Table has replaceable steel slats. Plasma head is mounted on a tracer/ panto graph pivot. It was set up to cut circles. There are several circle forms included. See pics. Other use may be to modify to a CNC. This has been in storage for several years. 110V. Buyer must arrange shipping. We can load onto truck. We are able to take CC via phone.
|
|
|
MG High Definition CNC Plasma Table
1996 MG(now hypertherm) high definition cnc plasma table and plasma cutter. Cutting table is 96"x120" and overall dimension is 112"x140" Auto torch height control. And water coolant nozzle on the torch head. I have videos of the machine running if requested. DNC 2.8 controller. and will include V26 Bob Cad/Cam software with training videos. You would need to purchase a new license for the software.
|
|
|
Victor Torch Plasma Table - For Parts Not Working
Item: One(1) each USED Victor Pattern Torch and various accessories. Sold As-Is for parts and not working. Table is approximately 44 1/2in long.36in wide, 41in tall. I know little about this equipment. Please ask questions. Shipping: This item is available for LOCAL PICKUP in Fresno CA. If you(Buyer) are interested in FREIGHT OPTIONS. I suggest looking into Freightquote.com or other similiar online resource- this will take some research and effort on your(Buyer) behalf. After you have performed a bit of cost analysis. Please contact me- I will be happy to work with you on filling in the"blanks" that will help in obtaining an accurate freight quote from your(Buyer) selected carrier and discussing additional costs(if any) associated with crating, palletizing, packaging, loading, etc. Other Info: Many of the items I sell are used. ... moreBuyers should anticipate normal signs of use- at a minimum. Most items will need a quick cleaning. I try to describe items as best as I can. But I am not an expert on any of the items I'm selling. My opinion of an item's condition may not match yours- please ask questions to make sure you are comfortable with a purchase. I'm generally pretty reasonable with requests(although not always quick) and appreciate your interest in an item. Posted with eBay Mobile
|
|
|
PlasmaCAM Model DHC2 CNC Plasma Cutting Table, 4' x 4', Hypertherm Powermax 45
Beautiful. Fully operational PlasmaCam removed from a small shop in Minnesota that closed. PlasmaCAM Model DHC2 CNC Plasma Cutting Table Serial No. 13883 Computer with PlasmaCAM DesignEdge Software NEW Cutting Grate 4' x 4' Cutting Area Software indicates unit has only 2 hours of cut time on it! software license is transferable) please note. The only item missing is the back clamping holder for the torch, this can be purchased or made by you) And Hypertherm Powermax 45 Plasma Cutting System 1/2" Steel Capacity 220V. Single Phase Assorted NEW Nozzles. Electrodes and Shields for use with or without the machine. http:www.plasmacam.com/machspecs.php. Http:www.hypertherm.com/en-us/Products/Handheld_cutting/Systems/powermax45.jsp. Please call 612-564-FRAM if interested. Shipping arrangements can be discussed before you purchase. Returns ... moreare accepted if the item arrives not as described or does not function as described. Please review the photo's closely so you are not disappointed with your purchases. Thanks!
|
|
|
Lockformer plasma burning table
Lockformer 5' x 10' table. The contol box was refurbished last year. The plasma cutter is a Hypertherm 1000 approx. 3 yrs old. It has a complete sheet metal cutting software and a misc. parts cutting software. Table is in good working order. Can be seen running! All moving and shipping costs are at the expense of the buyer
|
|
|
CNC High Definition Hypertherm HPR130 Cutter & AKS Accu-Kut Plasma Table
This is a used AKS Accu-Kut along with Hypertherm power supply and controls. This auction is for: AKS Accu-Kut 5x10 table with water tray. Hypertherm EDGE Controller. Hypertherm HPR130 High Definition Plasma Cutter. Hypertherm Manual Control panel. Gas lines and wires. HPR130 consumables(I would estimate between $500 and $1000 worth) 8x20 metal shipping container. Table is of unknown year. I believe it's 1990's. The Hypertherm equipment is from 2004. This was purchased from a liquidator who got this from a defense contractor that had filed bankruptcy. I purchased it in it's current condition. About 8 months ago, out of storage, untested. I was told it was in working condition when it was stored. Due to not being able to put a power source to it, I have only been able to test one thing, the EDGE Controller, which powered on and ... moreworked just fine. Manuals are included, which contains the password for the EDGE Controller. When making offers/determining worth. Please consider the crate alone is worth roughly $1000. The Hypertherm HPR130 plasma cutter itself is worth roughly $30,000 new. I talked to Hypertherm about this and asked them what would be the most expensive component on it that could fail. Assuming everything was connected properly nothing should have failed. However the most expensive item on the HPR130 is a circuit board worth roughly $2500. Of course nothing here is new but this crate has some pretty expensive equipment inside of it. Shipping: A flatbed is recommended. The crate can be put directly on the flatbed and hauled away.
|
|
|
CNC Plasma Table, 6'x20' / Hypertherm Powermax 900
I'm selling this CNC plasma table for a local company. Will be listing an AMADA Shear and other items soon! Low usage. Built ~2000. Used Converted to Mach3 2 years ago. New PC CNC Plasma Torch: Hypertherm Powermax 900 Controller(can cut up to 1” of steel) Table Size: 7' x 21' Working Envelope 6’ X 20’ Table Construction: Extra Heavy Duty Steel Frame Computer comes loaded with Windows XP and includes a license for Mach 3 and SheetCam. Linear bearings utilized for gantry movement along rails. Schematics and spare motor drivers included. Video of machine under power. Taken in February 2014. Video Link#1: Video Link#2: Buyer responsible for freight logistics and expenses. Contact Reed to schedule an inspection. Pickup, or purchase. 541-815-2346. 10AM-3PM Pacific Time. Monday to Friday Bend. Oregon The plantary gearheads may need to ... morebe replaced. some backlash is present) Table is under power and ready for inspection. The CNC table is located 5 minutes from the Bend/ Redmond Airport. 1 hour of rigging will be provided. A flat bed trailer or truck will be necessary to transport. NO fenders higher than the trailer bed are allowed. Buyer to verify all specifications and options of equipment prior to purchase. The equipment is authentically represented. The Seller disclaims any warranty. Expressed or implied, of the year, model, hour reading, guarantee of merchantability or fitness of the equipment; the goods are sold in an"As Is, Where Is" condition. The seller warrants that the goods are free and clear of all liens. Indebtedness, or liabilities. SUBJECT TO PRIOR SALE.
|
|
|
CNC Plasma Oxy-Fuel Burn Table - Hypertherm HT2000LHF
CNC Plasma and Oxy-Fuel burn table. Gantry is made by C& G Systems. And is a Challenger model, water table was made in-house at the time of installation, and is included. Current setup is sized for a 10-ft x 10-ft plate cutting area. Will cut up to 3" thick plate on Oxy-Fuel, and 1" thick on Plasma. System can be viewed under power until mid May, when we will be removing it for installation of a new one, at which point it will be available for pickup. Includes: C&G Systems Challenger gantry style CNC cutting system- Cleveland Motion Controls Burny 5 CNC control- Water table. Has water storage tank below table surface for quick water level adjustment(using shop air) Hypertherm HT2000LHF 200A Plasma power supply- 1 x Machine plasma torch head. 2 x Oxy-Fuel torch heads- Torch manifolds. Solenoids, etc. no fuel, gasses, or cylinders ... morehowever) Manuals. Diagrams, etc. related to Burny 5, Challenger cutting system, and Hypertherm plasma power supply. Any plasma consumables left over when we decomission the unit(new unit uses different consumables) Plasma power supply is 240v 3-phase. Water table uses compressed air to adjust water level, CNC control and cutting system run on 120v single-phase power. Payment to be made in certified funds. Please contact with any questions. Unit is for sale locally as well. As such, we reserve the right to end the auction at any time. Unit sold as-is, with no warranties of any kind. Powered by The free listing tool. List your items fast and easy and manage your active items. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-1459845dbec-0x111-
|
|
|
Lightning CNC 5'x7' plasma cutting table
Table was tested but never used in production(like new) Hardware: Complete 5x7 Table 4-axis Breakout Board Gecko G540. 4) Nema Motors on the X. Y and Z Axis Dual motors on the Y axis for better accuracy Rack and pinion drive X and Y Railing Ball Screw Z Axis Plasma Cutter(Machine Torch) Mounting Bracket included Computer included with Windows XP. Monitor. Keyboard and Mouse included as well. Software: Mach3- This software will be used to control your table. SheetCAM- This software is used to create your G-Code needed for Mach 3 Cut 2D and Lazy CAM. No plasma cutter or water table included. Call or text me at 951-965-7035 to discuss possible shipping terms. A;06d2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28%3Ea%3B06d2-1459d104545-0x114-
|
|
|
Torchmate 2x4 CNC Plasma Table
Torchmate 2x4 used in great condition. Included in the sale is AVHC, Cad Light Software, Thermal Dynamic A40 Plasma Cutter, Shop made water table with stand Machine is runs and cuts great
|
|
|
TorchMate cnc plasma 2x2 with 2 x 4 water table
up for sale is my torchmate cnc plasma 2 x 2 growth series. With a 2 x 4 water table and a hypertherm power max 85 with machine torch and arc voltage height controller, AVHC) and a Husky pro 60 gallon 3.2hp motor 10.2 scfm@90 psi compressor, i have purchased everything brand new 2 years ago everything has aprox 100 workinh hours, this machine is still setup and in great working condition i have greased and oil all parts after every job.I have a lot of consumables and extensions motor cables, anyone that is interested can setup an appointment on a saturday or sunday to see this machine work before anyone buy it.I have the dxf files to make the slats for the water table, and the machine will come with all instructions and i will throw in the laptop that i use with it, asking price $12.500.00 customer must pick up,i will not ship this item, ... moremachine is sold as is. No warrinties, no exchange, no refund, please feel free to contact me at any time, 631-245-9522, good luck,
|
|
|
C&G Challenger Plasma / Oxyfuel Cutting System Burny 3 Plasma Table 10' x 8'
1997 C&G Sytems. Inc. Challenger Plasma/ Oxyfuel Cutting System with Burny 3 CNC Controls Upgraded in 2009 to Thermal Dynamics Auto-Cut 200 amp power supply. Remote arc starter box, gas module and torch body assembly Effective cutting Area: 10' x 8' New gear boxes New long axis rails and drive gears New torch body assembly installed 6-6-2014 Cuts up to 1.5" material thickness with a quality cut Plasma capable of cutting material up to 3.5" thick with an edge start Very well maintained Good used condition All reasonable offers will be considered Check out for a full video of the plasma in operation. Normal 0 false false false EN-US X-NONE X-NONE
|
|
|
PLASMA CUTTING TABLE - KEMPER - ESAB - 4 ZONE Downdraft with fan 1600 x 2000
Hi what we have for sale today is an: KEMPER PLASMA CUTTING TABLE- DOWNDRAFT near new! This item was purchased for a research project that is now entering it's next phase. So a bigger machine is on it's way. Solidly built this is no toy. 4 separate downdraft zones, the profile machine as it moves over the cutting tale triggers pneumatic switches that open flaps to the independent zones. Includes exhaust fan(3 phase) and is in excellent condition. Table area is 1600 x 2000. Forklift available for loading and item is located in Cheltenham. Inspection is available BEST QUALITY! RPP of $6.575.00 each plus taxes Grab an absolute bargain Please note that the picture is of the actual goods Bid with confidence. Brand new in original packaging! GST invoice with goods for Australian businesses. Low starting price. Plenty more quality brand ... morenames to list. Check out many of the other automation and engineering products we are listing. Pick-up is fine and we can box the unit for international delivery. Please note: Pictures form part of the description. If in doubt please email for further information. Check out my
|
|
|
ESAB Shadow 2 CNC Plasma Table - Need New Control Panel
We have a used ESAB Shadow 2 with a 200 amp power source. The panel stopped working. So we decided to buy a new one. Estimates on a new panel was around $15000. Maybe a after market is available for less money. This was purchased new around 11 years ago and used it part-time on one shift for 4 years, then used it seldom over the past 7. The burn thickness could go past 1" However the comfort thickness was 3/4" or less. Can fit a 8' x 10' in its burn area. All software, leftover consumables, manuals are included. Any questions. Please ask. Thank you!
|
|
|
CNC Plasma Cutter 5 x 10 water table Koike PlatePro 1500 w/ Hypertherm Plasma
AC Servo X and Y-Axis Motors and Interface Cables $20.375.00 $20.375.00 1 10ft Rail/Pedestal Package Effective cutting length of 10ft Overall rail length 14ft Includes Rail Weldment. Pedestal Weldment, Hardware and Cable Carrier $5.340.00 $5.340.00 1 Hypertherm Edge-Pro and Koike Drive Interface w/Operator Console Windows® XPe SATA Hard Drive 15" Glass Touchscreen 1 GB Memory 2 USB 2.0 Ports Two Station Op-con Part Program Support Remote Help Networking Auto gas Support DXF Input Simple Shape Nesting Cut Pro Wizard 2-Year CNC Warranty Koike Drive Interface Assembly 2-Axis AC Servo Drive Package NEMA Electrical Enclosure/Machine Interface Power Disconnects 800 IPM Rapid Speed I/O To Support Up To 6 Tools Koike Operator Console Supports 2 Plasma Stations Supports 4 Oxy-Fuel Stations Supports Marking Functions Input Power for Machine ... more208VAC or 220VAC. 60hz, single phase, on a 15amp circuit Remote CNC Pedestal Mount CNC Pedestal to be remotely mounted 5 feet from the front of the main drive rail $24.950.00 $24.950.00 1 Plasma Torch Station. Mounted on Master Carriage, heavy duty With plasma interface $1.150.00 $1.150.00 1 POWERMAX 105 Plasma Cutting System by Hypertherm Plasma Voltage: 240 Volts 3 Phase Output Current 30-105 Amps Single Plasma Gas System- Air or Nitrogen Shield Gas- None Required Self regulating primary input 200-600V. 3-phase(CE 230-400V, 3-phase) Input power conditioner compensates low line and power line fluctuations Gas Supply- Clean dry. Oil free air or nitrogen@460 scfh, 85 psi flow rate Continuous pilot-arc switch for cutting expanded metal or grating Spare consumables parts kit and positive work lead cable Machine interface Recommended Pierce Capacity- 3/4" Mild Steel Maximum Pierce Capacity- 7/8" Mild Steel Maximum Edge Start- 1-1/4" Mild Steel 200-600V. 100% duty cycle@ 94amps Standard Model Input Voltage: 240 Volts 3 Phase 200-600V 3-phase Recommended Fuse@ 200V/208V/240V: 80 AMP Slow Blow Recommended Fuse@ 480V/600V: 40 AMP Slow Blow Recommended Fuse@ 230V CE: 80
|
|
|
2003 MESSER METAL MASTER 3 PLASMA CNC BURN TABLE 6' X 20'
2003 MESSER METAL MASTER III HYPERTHERM HD4070 POWER SUPPLY RECONDITIONED HYPERTHERM HD4070 GAS MIXER NEW HYPERTHERM TORCH AND LEAD SET FROM IGNITION CONSOLE HYPERTHERM EXPLORER CONTROL G-CODE WITH NETWORK OR 3-1/2” FLOPPY IMPORT SHAPE MANAGER BUILT IN FOR SIMPLE SHAPES SINGLE SIDE DRIVE WITH HEAVY DUTY GANTRY DOWNDRAFT TABLE COMPLETE WITH VENTILATION 1” RATED CAPACITY BUT WILL EDGE START 1-1/4” VERY WELL 200 AMP UNIT 6’ X 20’ TABLE Table is currently at Arc Solutions in Hicksville. OH. And is currently under power however the ventilation is not hooked up there. This table has been in our shop for a little over a year. It is in great working order; we downsized to a smaller table to save space. We did recently have some trouble with a bad set of leads. That has all been replaced with new Hypertherm Components. We have also replaced the X ... moreDrive Gear Box recently. The Y axis Gear box does have a little bit of play but is still cutting very well. Smooth Motion every Direction and good working THC. We have mounted the Power Supply on a pan so everything can simply be loaded on a truck and set up in your shop with only running power.
|
|
|
Viper CNC Plasma table with Everlast 60c plasma, 4x4, table, PC and Cabinet
Barely Used 4 foot x 4 foot CNC plasma table Complete turn key with THC(height control) Plasma Unit: Everlast 60c Plasma paid $1295.00 for just the plasma cutter alone Viper Plasma CNC 4 x 4 Bosch module table that can be extended PC complete with Mach 3 and all software needed to run 15" monitor Printer/Scanner Consumables extra motor included. How to Books and Manuals Bought for $6500 for a business opportunity that didn't pan out and now I'm forced to sell My loss is your gain! I can break every thing down and crate ship just please contact to me before purchase to make arrangements. Buyer will be responsible for all shipping cost) Call or text for addition pictures or details thanks, Derek 330 569-4678
|
|
|
ezPlasma Model: APC CNC Plasma Cutter Table 4'x4' with Miller Plasma Cutter
Description Our'Affordable Plasma Cutting' system offers you a complete system. The APC has Automatic Torch Height Controller. As well as more than 5000 pre-drawn images. Extremely Durable 100% Welded Steel Construction 4" Deep Waterbed with Removable Steel Grates Torch Height Control Miller Plasma Cutter Full Computer System Full CAD Software Tool Pathing Software Control Software Sign Torch- 5000 DXF Images Specs: Linear Guide Rails 342 oz/in Stepper Motors Dual Drive Rack& Pinion X& Y Axis Ball Screw Lifter 4" Stroke Travel for Torch 800 IPM Rapid Traverse Speed.
|
|
|
Sector Spectrum Cnc Plasma Table 10x20 W~Hypertherm HPR260XD 1-Yr Old Torch
NORTHERN MACHINERY SALES INC 12F JOHN RD SUTTON MA 01590 508-581-9922 WHERE THE METAL MEETS THE TOOLS! For Sale: SECTOR SPECTRUM 10X20 HIGH DEFINITION PLASMA/OXY CUTTING SYSTEM PLEASE ALLOW 3 WEEKS FOR REPLACEMENT OF CONTROLLER FROM ORDER(Torch Specs are listed below with Machine controller specs) New in 2007 Sector Model Spectrum Cnc Gantry High definition cuttong system Machine torch: Hypertherm HPR260XD New 2013(with remaining 2 years of factory warranty) Machine Controller: Burny Phantom(New Replacement to be provided pre-shipping) Machine cut envelope: 10x20 rails only(Table not included but may be provided priced on request wet/dry) Gas torches included-1 Gas control included: Yes Torch Height Control: Yes True hole technology: Yes Brushless Motors: Yes Kallmorgan 650 watt ac brushless Dual side drive Collission Sensor: Yes Stress Relieved ... moreMachine bridge: Yes. Rack& Pinion Drive planetary Gear boxes: Yes. 10" Active matrix Lcd Touch screen: Yes. Stainless Steel Drive: Yes 2" for mirror image cutting. Heat Shield Cable protection: Yes. 0-500 I.P.M Cutting: Yes. 1000 I.P.M Travel: Yes. Machine will accommodate up to 6 oxy stations( Is equipped with 1 at present) Machine will accommodate up to 2 plasma torches- equipped with HPR260XD) Now. Warranty included: mechanical warranty 6 months provided. Manufacturers suggested retail value 225.000.00: equipped with this particular torch. Delivery Available: Yes within New England. Shipping is available at prevaling rates anywhere in the country and Canada( Customs and additional cost may apply) HYPERTHERM SPECS: The HPR260XD offers unmatched quality HyDefinition cut to half the operating cost and is now available with the new True Hole technology patent. Torch Includes Remainder of Manufacturers warranty equal to nearly 2 years Main advantages: New HDi technology for thin stainless steel plates- Uniformity and quality higher cutting- Maximized Productivity- Operating cost minimized- Unsurpassed reliability Cutting capacity carbon steel dross P
|
|
|
7'x20' CNC Plasma Water Table Hypertherm Powermax 900
Up for auctions is a 2013 HD 7'x20' CNC plasma table with a 400 gallon coolant tray. Table comes complete with a Hypertherm 900 plasma with a 25" torch lead. Control computer with CAD/CAM software installed and ready to run. Turnkey and ready to work! The only reason we are selling is we need something bigger. If you have any questions please call 918-694-7710. This cannot be shipped because of the size and weight. But we will help with loading.
|
|
|
Precision Plasma Table 4x4 with Computer
Precision Plasma 4x4 table with water slats and SS water pan. CandCNC electronics package Digital torch Height Control Dedicated PC with Mach 3 and Sheetcam Hankinson Air Dryer. This table has made 3 cuts and as you can see is now broken down and on a pallet. I have the manuals for the system to help you get going. Buyer is responsible to arrange shipping. I can load it with our forklift. 336.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E336-147228865a4-0x116-
|
|
|
ezPlasma Model: APC CNC Plasma Cutter Table 4'x4' with Miller 375 Plasma Cutter
Description. Save over 280% off of a new one. Affordable Plasma Cutting system offers you a complete system. The APC has Automatic Torch Height Controller. As well as more than 5000 pre-drawn images. New sold for over $10.000. A new model from the Manufacture is listed@ $14.000. Buy this one and save over $9.000. 49" x 49" Cutting area(Footprint 63" X 63" 48" x 48" x 4" Grated Steel Waterbed Gantry Clearance of 4" Stepper Motor System Plasma Cutting Unit: Miller Spectrum 375(120-230 Volt Single Phase) Recommended Cutting 1/4" Mild Steel) Max Cutting Depth 1/2" THC Automatic Torch Height Controller(keeps torch parallel with material) Control Software: Standard Mach 3 Control Software CAD: Vectric VCarve Pro(Drawing Software) CAM: SheetCAM(Tool Path Generator) X-Axis Cable Carrier to Protect ... moreHoses. Lines, Cables, etc. Computer Control System Set-up and Tested(15" flat screen. Laser mouse, keyboard) Machine Voltage 110V 20A. 120V 20A, 230V 15A Min) Specs: Linear Guide Rails 342 oz/in Stepper Motors Dual Drive Rack& Pinion Belt Drive X& Y Axis Ball Screw Lifter Z Axis 4" Stroke Travel for Torch 800 IPM Rapid Traverse Speed. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf52%3E-1472288659f-0x115-
|
|
|
4x4 4x8 CNC PRECISION PLASMA TABLE ROUTER TABLE
Up for sale is a used Precision plasma 48"x48" work surface CNC plasma table.My brother and I built this table in 2011 and at that time it was a 4x8 table I cut it down because I did not need that much.The table is sold WITH OUT the plasma cutter.The table includes a 1 48" Precision gantry with a floating head and touch off switch. 4 240oz stepper motors,1 Gecko 540 4 axis driver,1 CandCNC breakout board,1 CandCNC interface card to hookup your plasma cut,1 CandCNC LCTHC controller with LCD display,1 30v power supply,1 PC with a legal copy of MACH3 and a legal copy of Sheetcam,1 computer stand with key board and monitor and all the cables needed to hook every thing up.I built this with the intent of maybe starting a small fab shop with my brother, that does all the AutoCad and Cam programing but he is in the army and has been ... moreresigned to Italy so I cant use the the table.I never got the LCTHC height controller fully setup but the manual can be down loaded off the CandCNC site.I still have the other part of the table if you would like to make it a 4x8 table but I will charge an extra $100 dollars for shipping.Please email me with any question. Flat rate shipping to the lower 48 U.S.STATES.Please do not bid if you do not want this table. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*a4%601gc%3E-1472d92bbd0-0x111-
|
|
|
CNC plasma Table Burntable
this is a gently used cnc plasma table by Burntables.Ready to work,hyperthem power max 45 plasma cutter,software and computer ready to work, will cut up to 1/2 inch steel
|
|
|
Victory II cnc plasma cutting table w/ drill 300amp
Purchased new in may 2013 for a project that was cancelled. 6X12 cutting capacity. Pierces 2" steel. Will side start and cut 3" High definition plasma for cleaner cuts. Has Suhner PBM13 drill attachment for cnc holes also. Water table so very little smoke if any. 300 amp Thermal Dynamics power supply. 480 3ph. Thousands in extra consumables. Cuts steel, stainless, aluminum. Water or gas shield. Sells new for 100k. Can load on truck for free. Call Lee with questions 903-692-0496
|
|
|
Fast Cut Icon Elite Series CNC Plasma 5×10 Cutting Table Thermal Dynamics A120
Fast Cut Icon Elite Series CNC Plasma Cutting Table General Info: Stock# JG-141005 Machine Name: Fast Cut Icon Elite Series CNC Plasma Cutting Table Condition: Used. Good Brand: Fast Cut CNC Model: Icon Elite Series Year: 2010 Location: GA Specifications: Icon Elite Series CNC Plasma has a 5x10' table with a 3" total working envelope on the z axis. The machine is equipped with 570oz-in hybrid step motors and a dual drive linear guide system. The drive system runs on helical rack and pinions on the x and y with a enclosed ball screw on the z. The max cut speed is 400 ipm with a rapid traverse speed of 500 ipm. The Icon Elite Series CNC Plasma utilizes a A120 Thermal Dynamics Cutmaster plasma cutter. The cutter has a cutting capacity up to 3/4" The setup also comes with a Ingersoll Rand D25IN air dryer. The Icon Elite Series CNC ... morePlasma also includes the controller which has TurboCAD. Sheet CAM and Mach III CAD/CAM software included. Additional Info: The Plasma Table is currently under power and can be tested. Seller Contact Information: Jamie Gose 404-630-3657 The Equipment Hub. LLC 1380-A Beverage Dr. Stone Mountain. GA 30083 Are you looking for a different machine than the one listed? Visit our to see other machinery options. It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week.
|
|
|
ThermalArc Plasma Cutter Cooler Unit for Industrial Torch CNC Table
Used Torch Cooling Unit. Will Need a New Belt and Fuse. Sold As-is. Will ship freight if necessary. Unit weight-106lbs 40g.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2B%3E40g-1479bbd9601-0x10d-
|
|
|
Taurus 2000 Plasma Cutting Table
System Specifications Cutting Widths 8’ 2.4m) Actual is 10' Length Is 26’ 7.9m) Actual is 30' Constructed Of Heavy Structural Steel Tubing, Cutting Station Capacity 10 Stations Maximum, Up To 4 Plasma Stations, Up To 8 Oxy-Fuel Stations, 1 Marking Station, Precision Plasma Systems Up To 1.000 Amps Available, Integrated PC-Based Burny 10 LCD Plus Controller(New) Easy-To-Use 15″ TFT Touch Screen Operation, Windows XP Based Operating System, 80 GB Hard Drive/ 1 GB RAM, USB Ports/ 3.5″ Diskette Drive, 900 IPM Drive Package, SERCOS 750 Watt. Brush-less AC Drive Motors, Precision Machined And Hardened Linear Ways, Pedestal Or Floor Mounted Rail Systems, Hardened 90# Tongue-In-Groove T-Rails, Band Drive Torch Positioning, Enclosed Power-Track On All Axis, Customized Air Filtration System(Included at no additional charge)
|
|
|
L-tech burn table plasma table water bladder
This is a L-Tech 250 the model number is cm 250 100 c rh the serial number is 88 4034 ast. The ship date on the unit is 6/1/88 powered with a Pak 45 Brand New. 400 amp plasma has a burny 5 controller with the replicator 9001 up to 3 oxy torches this is a cantilever style will cut a 96x144(actually a 100x152) CUTS THICK MATERIAL This unit has a spare burny5 controller and has a spare pak 45 consumables and cables. 10.000.00 firm the pak 45 was 23000.00 so this is a steal the only reason we are getting rid of it is we have a brand new burntable coming
|
|
|
DIY CNC Plasma Burn Table Frame or CNC Router Table Frame by Gerber Scientific
CNC Plasma Burn Table or CNC Router. Frame Only Condition: Used/ DIY CNC Plasma Burn Table Frame Gerber Scientific. DIY CNC Plasma Burn Table Frame or CNC Router Table Frame 817-201-9908 Phone or Text is the quickest way to get a hold of me right now. This is the perfect frame for building your own CNC plasma machine or CNC router table. Which is what I got it for in the first place but have decided I am going to have to have a Fiber Laser machine instead. Yeah big bucks too. So why do I say this would be the perfect do it yourself frame. Well hear me out here. First this was originally a Gerber Scientific CNC router table frame and if you know anything about Gerber they only build high precision and heavy duty stuff. This table is all built with 3/16 wall tubing. Weighs over a 1000 lbs, two people can't even pick up one end I promise ... moreyou. Table is square. All tube joint welds are ground flat. As you can see in the pictures, it was nicely painted but I have had it sitting outside so it now has some minor rust stains. Another reason I want to sell it while it's still nice. This frame would make what I believe is the perfect CNC plasma cutting table. It will allow you to easily make a 5' by 10' or 5' x 9' burn table with 3' to 4' at the end open. This will allow you to cut patterns in say large rectangular tubing that wouldn't fit on your burn slates and clear the torch. Etc etc, and or this leaves the end open to set up a C or 4th axis for tube cutting various profiles or shapes etc. Also you could get scrap sections of 2. To 6 inch plate set up on saw horses etc. Replace the plasma torch with a oxy-fuel torch and burn out thick plate on those rare occasions. Then quickly go back to your standard plasma cutting table. Best of all worlds here. That is how I would set up a plasma table anyway. Last there is 400 bucks or more worth of steel here and it would take a lot more than 500 bucks worth of time and labor to build this table I guarantee you. Easy to build in your head, but f
|
|
|
Flatbed Printer Frame - great for cnc plasma cutter or cnc laser table
This is a large flatbed printer that I purchased used with the intention of removing the pencil and replacing it with a plasma cutting torch. Unfortunately I never got around to it. This would be a great starting point for either a cnc plasma cutter or a laser cutter/ engraver Overall Dimmensions 102" x 62" x 40" X axis Travel: ~72" Y axis Travel: ~50" The motors are driven with 24 vdc motors and optical encoders. The motors have been tested and are working. Included are two computers. Each with a 2-axes Galil motion control card, which are untested. At one point I had everything hooked up, and was able to get some motion out of the system, but it was not homing properly. The overall condition is very good. The table is constructed out of high quality aluminum extrusions. The linear bearings are high quality. To get ... moreit running I would recommend getting a new computer with a new motion control card. There are freeware versions of software that could be used to control the movement. Freight shipment is possible, but $200 fee would be added for crating and prepping for shipment.
|
|
|
ESAB CXA Oxy Acetylene Torch Cutting Table Shape Cutter lk cnc plasma
ESAB CXA Oxy Acetylene Torch Cutting Table Shape Cutter lk cnc plasma Up for sale we have an ESAB CXA-64 Oxy Acetylene Torch Cutting Table in working condition. We hooked up both torches to oxygen and acetylene tanks and they both shoot out a cutting flame. The torches also travel forward and back and side to side. It also has a variable speed function to travel at a desired cutting speed. It currently has 7 feet of track to move side to side. But if you add more track and roller support you can go more than 14 feet. The travel from front to back is 4 feet. The is also a smaller cutting table to lay material on and it measures 8ft x 4 ft. Another great deal on Ebay. $ave now! Please contact me if you have any questions. Important: Please read below if you intend to bid. By placing a bid on this item you agree to the terms of this auction. ... moreShipping Buyer is responsible for shipping charges. The table will be shipped in two pallets from Hayward. CA 94545. Pallet#1 weighs 980 and measures 96"x64"x38" Pallet#2 weighs 1100 lbs and measures 121"x64"x58" Local pick up is free and welcomed. We have often surprised our customers with low shipping quotes. Please call me at 408-205-9062 for the best overall price. Payment Policy Payment must be made within 7 days from the end of the auction. Accept payments through PayPal. Credit cards, and payment upon pick up. International buyers must pay by PayPal only. Bank wire transfer is also accepted for National and International high dollar sales. CA buyers add 9.0% sales tax. Return Policy Returns will be accepted if there was an error in the description. Unless the item is being sold"AS IS" All sales of items that are sold AS IS will be considered Final. Refunds will be provided if item is returned within 30 days of purchase date in the same condition as received unless stated otherwise in the above description. Refunds never include shipping costs unless stated otherwise in the above description. There will be a 20% restocking fee charge
|
|
|
HYPERTHERM HYSPEED HT4400 400 AMP PLASMA CUTTER CUTTING SYSTEM FOR BURNING TABLE
HYPERTHERM HYSPEED HT4400 400 AMP PLASMA CUTTER CUTTING SYSTEM FOR BURNING TABLE Machine was purchased at auction. According to auction company. Machine was working when taken out of service but we do not have any way of testing the machine. Therefore, machine and components are being sold AS IS. We believe all components necessary for setting up and operating the machine are present. But only what is pictured is included. We do know that all standard components listed in the manual are included. System Features(Note: From Hypertherm HT4400 Manual; to our best knowledge all information from manual applies to this machine. However there is no guarantee* The Power to Do More: The only 400-amp dry oxygen plasma cutting system on the market gives you the power to increase productivity. Reduce cutting costs and increase profitability. The HySpeed ... moreHT4400 delivers the exceptional cutting speeds required to dramatically increase throughput– especially on thick plate production cutting. No other system available today can match the speed, cut quality, economy, reliability and ease-of-use of the HT4400. The HySpeed HT4400 gives high-volume metal-cutting operations such as heavy metal fabricators, steel service centers, structural steel operations and shipyards more power than they ever had before. If you want to cut the widest range of metals faster than was ever possible, there is literally only one choice. Put the HySpeed HT4400 to work breaking speed limits for you. Built for Speed: The HySpeed HT4400 is the world’s first 400-amp dry oxygen plasma cutting system. Its single power supply delivers unmatched cut speeds– especially on thicker metals that laser systems can’t cut. Delivering cut speeds of 95 ipm on 3/4-inch mild steel(2298 mm/min. on 20 mm) and 70 ipm on 1-inch(1806 mm/min. on 25 mm) No other metal-cutting process can keep up. At the same time, the HT4400 produces virtually no dross and delivers superior cut face weldability over the widest range of material types and thicknesses. This makes the HyS
|
|
|
1993 MG CNC PLASMA CUTTING TABLE
MG INDUSTRIES CNC PLASMA CUTTING TABLE YEAR;1993 MODEL; METAL MASTER TABLE; 16" X 80" TABLE CUTTING CAPACITY; UP TO 3/8" HYPERTHERM HD-1070 PLASMA POWER SOURCE RSVP-301 CUTTING TORCH HEAD*DISCOUNTED $10K FOR A FAST SALE* SUBMIT ALL REASONABLE OFFERS! PLEASE CONTACT US ABOUT RIGGING SERVICES BEFORE BIDDING Terms and Conditions: All bidders are responsible to determine the age. Description, condition, and authenticity of all Purchased items. This machine has not been tested under power by any of our employees or our company affiliates. Each item is auctioned“AS IS, WHERE IS, with all faults” in its condition at the time of sale, without any warranties or guarantees, either expressed or implied, INCLUDING BUT NOT LIMITED TO WARRANTIES OF TITLE, POSSESSION, QUIET ENJOYMENT, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE, ... moreand without recourse by way of refund, reduction of the Purchase Price, or otherwise. Taxes are applicable to all purchases unless an exempt form or re-sale certificate is emailed/faxed to us. Shipping and Handling: Bidders are responsible for all Shipping and Handling charges. Delicate and expensive equipment requires special handling to ensure its safe delivery. Seller and Buyer have the option to allow the Buyer to choose it's own rigging company for item removal. But Seller has final say to selecting rigging personnel for the item removal. Please send us a message with your zip code to get an estimate quote for transport! If you have your own method of transport. Let us know before payment! We Ship Worldwide!
|
|
|
4x4 CNC downdraft Plasma cutting table
Selling my 4x4 CNC downdraft table. I recently upgraded to a 5x10: This listing is for table/ electronics/ mechanical only. It DOES NOT include the plasma cutter or software license. The software is installed and configured. But you will need to purchase a MACH3 License and a Sheet CAM license(fairly inexpensive) I will include an 2002 version on AutoCAD LT This is plug and play for a Hypertherm Powermax series plasma cutter. Includes mounts for both a hand torch and machine torch(but not the torch) This table does include a very basic stand alone Torch Height Control Module, however I very rarely used it for what I was doing. It will require Raw ARC voltage Motors are driven by a Gecko G540, not a cheap import board. Everything you see attached to the table in the picture is included. I am located in Northern Virginia in between Leesburg ... moreand Winchester. I will not ship this item. I can help you load. This item is sold AS-IS and is not warrantied and does not include technical support. Rather than list every minute fact, please just send an email if you are interested pinegroveranch@gmail.com This table is for sale via other listings, so I reserve the right to end the auction. I will accept cash or check if you are willing to wait for it to fully clear my bank(probably 5-10 business days)
|
|
|
Burny3 Plasma/Oxy Cutter Table
Plasma Cutting system with water table(400 AMP) Esab sidewinder 400 amp plasma with(1) plasma torch and(1) oxy cutting torch. Plasma will cut 1" steel. Oxy will cut 6" steel. Burny 3 software. Includes water cutting table- can handle 10'x24' plate. Cantilever type. Sold as is. Where is, buyer to disassemble and rig. Contact us with questions or request dimensions. Free local pickup.
|
|
|
Esab Piecemaker 2 Cnc Plasma table
Up for sale is a Used Esab Piece maker 2 Cnc plasma system in amazing shape with very little use. In near perfect condition. Table is setup for vent but could be converted easily to a water table. Includes box of extra consumables. Esp 50 power supply with additional cover all manuals original invoices. Decided to go a different route in our fab shop This machine is a work horse and barely used Mfg is 2006 and has less than 20 hours of run time This unit with options sells for over $65k and has seen very little use Bid with confidence. I will help answer any questions you may have or take additional pics if needed. Shipping is the sole responsibility of purchaser Sold as is where is deposit through paypal with balance made by wire transfer, Bank check or cash. All funds must clear prior to releasing equipment SPECS OF POWER UNIT ARE AS FOLLOWS ... moreT ESP 50/ PT-35 Mechanized Plasma Cutting Package Cuts: 1/2 in(12.7 mm) Output@ 100% duty cycle 50 A, Air Requirements@ 60 PSIG(117.9 l/min. 4.1 bars) 250 CFH, Dimensions Width: 10.1 in(275 mm) Length: 20.3 in(576 mm) Height: 18.3 in(465 mm, Weight 85 lbs(38.6 kg) Input@ 35 A/ 120V 208/230 vac. 1 ph, 50/60 Hz, 46/42 A, 1 ph. 208/230) 208/230 vac. 1 ph, 50/60 Hz, 46/42 A, 3 ph. 208/230) vac. 3 ph, 50/60 Hz, 22/20 A, 3 ph. 208/230) 208/230 vac. 3 ph, 50/60 Hz, 22/20 A, 3 ph. 230/460) 400/460 vac. 3 ph, 50/60 Hz, 12/11 A,
|
|
|
NO RESERVE Great Value Large 6 x 10 CNC Plasma Cutter Table / Torch / Computer
Up for auction is an inherited Plasma Table with all the fixins? The tables total width is about 6'4" wide and 10'4" long on the outside and the controller cabinet adds another 8 inches width. The usable work area. Is about 4 x 8' The table is used but as the pictures shows is not beat up and in great shape. It is not dirty and does not have any accumulation of slag. The entire table is on wheels also. The computer is a HP Compaq with keyboard. 3ghz Pentium 4 with with 2 gig of Ram. Software is Microsoft XP Pro sp2 and also has a freeware graphics program, but you will probably want to use your own graphics program. The monitor is an 18" Gateway FP1810. Mach 3 ST6560-T4 Mach 3 Stepper Motor Controller. Air Plasma Cutter mod ATPC52 50 Amp Plasma cutter that adjusts from 10-52A and looks very new or very light use. ... moreIt cutter comes with two cutting torch heads. The standard version that comes with most any machine. And a straight version, as found on the table now. Also has a Torch height controller. PROMA Model THC Controller 150, which is mounted on the side of the plasma machine in the pictures The nearly new looking plasma cutting machine is an Accurite Tools model ATPC52. I hooked an air line and the second standard torch head that comes with this machine and was able to cut metal with it. I know nothing about plasma cutters and have never used a plasma cutter before. So that is the best I can do. It functions and cuts metal. The know nothing about these tables and have no desire to learn so the best I could do is turn it on. The table came alive with light buzzing and somehow got the table to move a little on its own with the software you see pictured on that 18" monitor. I don't want to do any more for fear of crashing something. Overall this looks like a good functioning plasma table with a computer and software to run it. I have seen my brother use this. But I never have and I don't know any history of the machine. The system turns on, makes some functioning noises an
|
|
|
Taurus 2000 Plasma Cutting Table C&G Systems
System Specifications: This machine is in very good condition. Although it is missing the torch cutter. Located currently in Eden TX. Year 2000 Power Supply- Hypertherm 3070 100amp(Pictured) Width 10' Length 30' Constructed Of Heavy Structural Steel Tubing, Integrated PC-Based Burny 10 LCD Plus Controller(New) Easy-To-Use 15″ TFT Touch Screen Operation, Windows XP Based Operating System, 900 IPM Drive Package SERCOS 750 Watt. Brush-less AC Drive Motors, Pedestal Mounted Rail System, Hardened 90# Tongue-In-Groove T-Rails, Customized Air Filtration System(Included at no additional charge)
|
|
|
CNC Plasma / and flame cutting Table machine 5 x12water table and tracing
NO RESERVE!this machine has an optical tracing eye. As well as a computer connection to load parts from a PC into the burny control. There is also a 5ft x 5 ft tracing table, there is a 50 shape library in the burny control that allows the operator to modify basic entities of the shapes by changing dimensions and angles etc. Water table included, this machine is sold up and running as is where is, and can make you a lot of money CALL WITH ANY QUESTIONS 516 852 8496 Frank Machine is under power and works well. A new Cutmaster 60 amp plasma has been installed in Oct 2014($3,500.00) has a Burny 3 controller, and C and G controller. unit is fitted with both plasma and oxygen acetylene torch. The oxy torch was never used since new. this unit is ready to work. Buyer must be responsible for disassembly and moving,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%600d72f%2B%3F0%3C%3E-149d702cd04-0x10d-
|
|
|
Vulcan Lockformer 3100D HD Plasma Cutting Table Hypertherm HD3070 THC HyDef
Vulcan Lockformer 3100D High Definition Plasma Cutting Table with Hypertherm HyDefinition HD3070 Plasma Arc Cutting System and Automatic Torch Height Control Low hours! Counter shows just 2.868.3 hours! GENERAL SPECIFICATIONS Maximum Cutting Width 5’ Maximum Cutting Length 10’ EQUIPPED WITH Northeast Electronics CNC Control Standard Shape Library Variable Speed Drives Lockformer PCM 8 Cutting Software Hypertherm HD3070 100 Amp Hydefinition Plasma Power Source Station Outlet Equipment Innerlogic Torch Lifter Dual End Drive on X Axis Innerlogic Torch Height Control Hypertherm Gas Mix Console Rack& Pinion Drives Heavy Duty Thompson Round Ways with Pillow Block Bearings Down Draft Table Top of the Lockformer Plasma Cutting Line This machine includes a computer with lockformer cutting software& consumables. Loading onto your truck is included. ... moreSystem Requirements Gas Requirements: Plasma Gas Types.Oxygen(O 2) Air Shield Gas Type.Oxygen(O 2) and Nitrogen(N 2) mixture. Methane, Air, Methane/Air mixture Oxygen Gas Quality.99.95% pure(liquid gas recommended) Nitrogen Gas Quality.99.995% pure(liquid gas recommended) Air Quality.Clean. Dry, oil-free Methane Quality.93% pure(commercial grade) All Gas Inlet Pressures.120 psi(8.3 bar) Oxygen Flow rate.77.8 scfh(2203 l/hr) at full scale Nitrogen Flow rate.83.1 scfh(2353 l/hr) at full scale Air Flow rate.81.7 scfh(2313 l/hr) at full scale Methane Flow rate.110 scfh(3114 l/hr) at full scale Torch Coolant Requirements(Torch coolant requirements are provided by power supply. Coolant Tank Capacity.2.9
|
|
|
Vicon plasma cutting table
Vicon 5x10 table.Torch and computer
|
|
|
Eagle CNC / Plasma Cutting Table 5x10' w/Computer & Software! L@@K
Please see pictures below. This listing is for a Eagle 5x10 CNC/ Plasma Cutting Table. This table was bought new and never used. Cosmetically it has minor scuffs here and there from moving it around but is still in excellent condition. It comes with a Dell Optiplex computer with Mach 3 and Qcad software installed. It appears to be a complete setup but I am not a machinist so I really don't know. I have pictured everything included with the table. This listing will be for local pickup only. If you have any other questions feel free to ask. Thanks for looking! Thank You. To all eBayers for helping us reach our goal of over 1 3.000 satisfied customers. Be sure to check out our other GREAT DEALS! Local Pickup Only Check out my other items! This auction will start out at $.99 NO RESERVE! Buyer pays for S/H/I. Be sure to add me to your favorites ... morelist! Shipping and handling will only be combined if auctions are won within 72 hours of one another. BY PLACING A BID YOU ACCEPT THESE TERMS: If you have no feedback rating or you are new to eBay. Contact us before you bid with your contact info. There are to many Newbies that do not pay Items are guaranteed to be in stated condition. If you are not satisfied with an item. You must contact us within 72 hours of receipt of item. Payment must be received within 7 days of the completion of the auction. We reserve the right to re-list the item if payment has not been received within provided amount of time. We also reserve the right to cancel the bids of any member with a negative( feedback rating. We never send second chance offers.if you get one it is not from us! This is an auction sale and the sale of this item will be considered final. All items are sold as is described but we guarantee our descriptions! We have endeavored to photograph and accurately describe every item as to its condition and authenticity to the best of our ability. We intend that photographs are part of the description- we take multiple photographs. If you are not sure what you are bidding
|
|
|
Tracker Nitro CNC Plasma Cutting Table 4x4 w/ software-cutter-computer! MICHIGAN
Tracker Nitro CNC Plasma Cutting Table 4x4 with software. Cutter, computer! We have upgraded to a larger 4x8 table. So our old 4x4 system needs a new home. This is a complete. Good working setup with 4x4 Table, Computer, Software, Plasma Cutter, Vent Hood, etc. The only thing not included is the Exhaust Fan, because we are using that with our new table. Table Size: 4 foot x 4 foot Software: Coral draw X4 and Command n' Cut Machine Control Software Plasma Cutter: Thermal Dynamics Pro A60 Cutmaster trackercnc.com/nitro MACHINE IS STILL SET UP AND CAN BE SHOWN RUNNING BEFORE PURCHASING. WE WILL UNWIRE AND HELP DISASSEMBLE AND LOAD WITH FORKLIFT. Prefer Local Pickup Only. Freight shipping would be very expensive. Located around Flint. MI SERIOUS INQUIRES ONLY
|
|
|
Dynatorch 4'x8' CNC Plasma Table
This auction is for a 2010 low hour 4'x8' work area) Dynatorch plasma table powered by 45 amp Hypertherm PowerMax45. The total footprint of the table is 5' x10' Options for this table include laser locator. Ohmic height sensing, dynascribe, and the oxy fuel setup which is unused as it came from Dynatorch. The unit is controlled by computer(not included in auction) although it does come with the Dynatorch software as well as Sheet CAM which is an easy to use manual nesting program for cutting single or multiple parts. You select a cutting torch size and then place the parts on a sheet and move or rotate them manually. Then you tell the software to process the sheet. The system will add in kerf compensation. Lead in, lead out and order of cut automatically and will give you a G-code file ready to run on the Dynatorch system. ... moreA similar new turn-key setup would run around $23.000
|
|
|
HYPERTHERM MAX 200 2" PLASMA CUTTER w/ HAND & MACHINE TORCH FOR CUTTING TABLE
HYPERTHERM MAX 200 2" PLASMA CUTTER w/ HAND& MACHINE TORCH FOR CUTTING TABLE Package includes: Hypertherm MAX 200 Plasma Cutter Power Supply w/ Cooling System, Hypertherm PAC200T Hand Torch, Hypertherm MAX200 Machine Torch(for use with automated burning tables and other automated systems) Ground Cable and Clamp, Features: Hypertherm Max200 Dual Gas Plasma Hand Cutting System delivers 150 V and 30 kW power output that provides heavy-duty cutting capacity up to 2" on most metals including aluminum. Mild steel and stainless steel. High capacity dual gas system with 66- 280 scfh flow rating and 90 psig pressure rating offers 100% duty cycle at full power to keep you cutting for long time. Cutting system used on heavy-duty metal cutting machines or for hand-held applications ensures clean. Square cuts throughout the cutting range. ... morePlasma cutting system features 40- 200 A adjustable current rating that allows the operator to accurately match the power for cutting requirements. System with built in machine motion delay control has a full set of easy-to-read indicator and diagnostic lights to monitor the transformer temperature. Coolant level, plasma and shield gas pressure, coolant temperature and coolant flow System features torch that uses Air/Air. O2/Air, N2/Air, N2/CO2, Ar-H2-N2 or other combinations for plasma and shield cutting to provide optimal results on all metals and in all conditions. Water-cooled torch that provides maximum cooling features shielded torch front-end that practically eliminates the possibility of double arcing. Enhancing piercing capabilities and extending consumable parts life. Power supply maintains constant output current regardless of variations in input voltages or torch-to-work distances. Ensuring clean, square cuts throughout the cutting range. Cutting system with built-in interlocks for maximum operator safety features casters for easy wheeling and has a lifting eye located at the balance point for use with cranes. Specifications: Serial: 200-002940 Input: 240(230)480(46
|
|
|
Working Vicon plasma cutting table in Bohemia NEW YORK
Vicon plasma cutting table for ductwork.This is a working Machine that was replaced with a faster machine.This machine is in Bohemia NEW YORK. `4`.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d71f%2B%3E%604%60-14a775e4ea2-0x116-
|
|
|
CNC Plasma Table with Hypertherm Powermax85
This is a barely used CNC plasma table similar to the one that is pictured. We purchased this unit in December of 2013. We paid for a factory rep to come install and train our staff on how to use this machine. After repeated attempts to get the factory to warranty the issues with this table we finally came to an agreement and sent the gantry in for refurbishing. Due to the delay in making all of this happen we purchased another unit from a different company and would now like to sell this machine. It comes with a barely used Hypertherm Powermax 85 with a 25' lead. It also includes the computer and software that came with the machine. We have not used this machine since it has been refurbished. The gantry is still in the crate that it was returned to us. We paid over 19.000 for this machine new and it has probably less than 20 hours total ... moreof use.
|
|
|
4x8 CNC Plasma Cutting Table Complete System with water table & Hypertherm 45
Up for sale is a complete CNC Plasma Cutting system. This heavy duty table will cut sheet metal up to 4x8 feet and 1/2" thick. This system has been a great money maker but we no longer have the time to keep up with orders. The system includes the following: Heavy duty 2x3" steel frame and 4x8 foot water table. This greatly reduces the smoke and mess made by others non water tables. The water also helps keep the thin metal from warping while cutting. CNC gantry system to easily turn a drawing into a metal piece of art in minutes. Dell desktop computer with stand. Loaded with all the software needed to operate the system. Inkscape, SheetCam, and Mach3. Automatic torch height control to keep the correct cut height throughout the cut for great cut quality. Hypertherm 45 plasma cuter with the machine torch. More pictures of products ... morethat can be made and videos of it cutting can be found at Topnotchfab(dot)com. Email with any questions.
|
|
|
20 FT VICON PLASMA TABLE
20 FT VICON PLASMA TABLE/ FULLY OPERATIONAL/ PLEASE FEEL FREE TO ASK ANY QUESTIONS YOU NEED ANSWERED. THE CURRENT OPERATER OF THIS UNIT WILL BE HAPPY TO SPEAK WITH YOU AS WELL.
|
|
|
CNC Plasma & Flame Cutting Table Machine , PakMaster 150xl, and Sony Laptop
CNC Plasma& Flame Cutting Table Machine 5 x 12 Water Table& Tracing This machine has an optical tracing eye. As well as a computer connection to load parts from a PC into the burny control. There is also a 5ft x 5 ft tracing table. There is a 50 shape library in the burny control that allows the operator to modify basic entities of the shapes by changing dimensions and angles etc. Water table included. This machine is sold up and running as is, and can make you a lot of money Machine is under power and works well, a new Cutmaster 60 amp plasma has been installed in Oct 2014($3,500.00) has a Burny 3 controller, and C and G controller. Unit is fitted with both plasma and oxygen acetylene torch. The oxygen acetylene torch was never used since new. This unit is ready to work. THERMAL DYNAMICS PAK MASTER 150 XL PLASMA CUTTER. This plasma ... morecutter was last used a few months ago when the Torch( PCH/M-120) stopped working. The rest of the machine is in good working condition but I had to buy a new machine right away and could not wait the week to have it ordered due to high business demands. The torch however can be replaced and a local vendor in Brooklyn will be able to order it if need be. Sony Laptop Vaio Notebook PCG-F630 This is a basic laptop but comes equipt with QuickCad and FastCam programs. These are the necessary programs to use the plasma cutting machine allowing the user to draw pictures and create programs. QuickCad is meant for setting up a drawing. Creating a template, trimming geometrics, adding dimensions, and plotting a drawing. FastCam is the full professional tool, including 3D modeling and rendering, symbol definition editing, and advanced capabilities for working with multiple drawings and overlays for steel use. CALL WITH ANY QUESTIONS: Frank(516) 852 8496 PICK UP ONLY. Brooklyn. New York- Buyer must be responsible for disassembly and moving.
|
|
|
Hypertherm CNC Plasma Torch and Kioki Cutting Table
Used. Free local pickup. As is. No warranties. Currently in operating condition. Please schedule an appointment to see a demonstration. Reason for selling: We are upgrading some of our shop equipment to newer models. Hypertherm model HySpeed HT2000LHF. Serial# 2LHF-000792 Cuts up to 3/4" thick mild steel plate. Water cooled head. Currently set up to use oxygen and nitrogen as the plasma cutting and shielding gases. Kioki model Platepro 2500. Serial# 00015PLP Single side drive. Table size 10 ft x 20 ft. Table has been modified with a floor chain to discharge small parts and slag out the end. Easy to clean out at the end of each day. Comes with the duct work for attaching a down draft fan. But no fan included. Complete with Kioki controls and automatic torch height control. It was purchased with the parts for a dual head oxyfuel attachment. ... moreBut never used it.
|
|
|
Esab ST5000 plasma cutter table CNC 2 torch system 10x30' cutting area 750 amps
Nice working Esab ST5000 plasma cutter that was removed from a Boeing facility. Make: ESAB Automation. Inc. Model: ST-5000 Type: CNC Gantry Plasma Cutter Serial No: 0220 Mfg. Year: 1993 Features/Specifications: Control: L-TEC Series 2000/70 Cutting Stations: 2 Cutting Area: 12' x 30' approx. 2) ESAB Flow Controllers 115V- 5A- 60 Hz P/Ns: 2235714(2) ESAB ESP600 power supplies 600A output Hypertherm water chiller system 2 torch; 600A capacity Fume collector trough Dimensions: Gantry Width(overall) 201" Gantry Height: 83" Gantry Floor Rail Length: 438" Table/Tub Width: 138" Table/Tub Length: 378" approx. Table/Tub Height: 32" Footprint(as shown) L 438" x W 236" x H 83" Condition: Good- working at time of decommission Normal wear from previous use in working industrial environment Regular. ... moreThorough maintenance performed since new call 920-946-7610
|
|
|
Torchmate Plasma Cutting water table 5x10 with Hypertherm 85 new 2012
5'x10' it was purchased in 2012 new. It has a Hypertherm Powermax 85. Includes the following: Complete Water Table with adjustable water height- Steel Fabricated Gantry with Dual x-axis Drive- Torchmate Cad and Torchmate Driver Software- Complete Microstepping Motor Electronics- Machine Interface and Triple Interface Cable- Low Backlash Gearboxes- Arc Voltage Torch Height Control with 50' cable- Heavy Duty Cable Carrier- Dell Desktop Computer and all software- Black Computer Cabinet Hypertherm Powermax 85 w/ 50' machine torch& lead(w/ CPC port& remote) P/N 087116 CNC Interface Cable 25' P/N: 023206 Laser Crosshairs with 50' cable extension(Determine what interface cable needed* Dual Interface Cable(allows both interfaces to be plugged in) Torchmate Universal Interface for Oxy Fuel. Plate Marker, or Router Plate ... moreMarker(long version) 110V with 50' cables for Torchmate Growth Series, 3& X,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*4a24%60%3C%3E-14b60ac214e-0x10a-
|
|
|
Lockformer Vulcan 1800 Plasma 5'x22' Cutting Table 150 XL Supply D-6 Controls
Lockformer Vulcan 1800 Plasma 5'x22' Cutting Table Pakmaster 150 XL Power Supply D-6 Hybrid Controls Thermodynamics Cuts 1" Owners manuals D-6 control recently rebuilt Many manuals.Extra parts,works great Shipping quote upon request
|
|
|
Plasma/ Oxy Torch parts trace table
Here is a used Torch/Plasma trace machine and table. Height: 6' Length 5' width 5' 120V. Machine traces previous parts and cutouts to create more parts of desired thickness. Machine comes with an array of traceable templates and magnetic dies. Oxy torch and hoses included. Plasma torch and interface cable not included. Buyer is responsible for shipping. Machine must be removed from sellers possession within 14 days after purchase.
|
|
|
2006 ACS CNC Plasma Table - Cutter II-510
You are bidding on a 2006 Advanced Cutting Systems Cutter-II-510 in excellent working order complete with manuals. Including the Profile Master 2000 Profiling Software. The Profile-Master is a powerful, flexible, production control program which is apllicable to a wide range of industries that use profiling such as ductwork, blow-pipe/duct extration, insulation laggin, general profiling, precision part manufacturers, steel stock-holders, and sheet metal industries. There is a video at this link: https:www.youtube.com/watch?v=eD2tyVU1WaI The new model's factory specs are at this link: http:www.advancecutting.com/Cutter2.php and there is a video at this link also. Here are a few specs on our machine: The Cutter-II is the 5' x 10' model. Our unit comes with the Hypertherm EdgeTi Touch Screen Color Graphic Control. Hypertherm Powermax ... more1000 Plasma. Floating Head. Down-draft Cutting. The table is rated at 5/8 max load capacity. Cutting Area 5' X 10' Positioning Accuracy +/ 012 inch Pierce Capacity(Max) 3/4" Mild Steel and Stainless. 5/8" Aluminum Traverse Speed(Max) 1.400 Inches per Minute Controller Hypertherm Ti Touch Screen Color Graphic Drive System Direct Drive Servo Motors through Planetary Gear Box to Rack and Pinion Standard Torch Height Control Floating head Standard Plasma Hypertherm Powermax 1000
|
|
 |