|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Condition: Used Location: Farmington, United States Anilam Crusader Series M Control. Includes monitor w/mount. Cabinet with all electronics/boards, scales, servo motors for"X" Y" and"Z" ... moreaxes and all mounting plates(some bolts missing and a couple bearings) Taken off of a Hurco Mill. When I purchased the Mill it was working. It had a new monitor installed. When I brought the mill home and finally hooked up the wiring in the barn, the monitor was not working. Since the estimate to have on-site repair was too much for a hobbyist, I removed the entire unit and made the mill a manual mill. When I purchased the mill, programs were working in the control and all axes were working. Servo Motor I.D. is as follows: Z" axis serial F32337- Type 30M4-59, X" axes serial R32143- Type 30M4-59 and"Y" axes serial F32108- Type 30M4-59. RS232 port is on the cabinet and a smaller cassette tape is located on the side of the monitor.Not sure what needs repaired to make the entire unit work. Great for parts. Buyer to arrange any shipping. Listed as Local Pickup.
Buy It Now
Condition: Used Location: Harrison, United States MODEL:SMX 3 -AXIS CNC SYSTEM. BRIDGEPORT PROTO-TRAK 3-AXIS CNC VERTICAL MILL. WITH SERVO MOTORS, MANUAL DATA INPUT 2 AXIS. BIJUR LUBRICATION SYSTEM. FLOOR ... moreSPACE.. 60" x 63" x 82".
Buy It Now
$10.40 Shipping Condition: New Location: Howell, United States "QUADRALLEL". This device is the result of years of "There has to be a better way" frustration, creative thinking, and the vision of one of the finest ... moreCraftsman / Inventor the industry has ever seen.
Buy It Now
$5.75 Shipping Condition: New Location: Eagle, United States Untitled Document Description Item: Vise Jaw Stop(Model: 14-000) Condition: New in Box Specifications Fits all milling machine vises with 1/2" 7/8" ... morethick jaws and 1/8" minimum protrusion 1-1/8" wide body with 2 hardened steel guide pins and large#10 clamp screw 1/8" x 2" hardened stop pin is used to accurately locate work pieces. The stop pin is also adjustable side-to-side to allow for cutter clearance The stop pin is positioned completely below the top surface of vise jaw to allow for cutter clearance Body made from anodized aluminum 8-32 non-marring flat point set screws are used to secure stop rod Vise Jaw Stop The Vise Jaw Stop by Edge Technology Products is the most advanced jaw stop to date. It features a micro stop rod that is positioned below the top surface of the vise jaws for cutter clearance. The stop rod is also adjustable side-to-side to allow space between the unit and the work piece for even more cutter clearance. Patent Pending Payment& Shipping Payments Accepted: Paypa l. Shipping USPS. See Shipping and Payments tab for details. Note: If multiple items are purchased from our store we will combine shipping. Please request a package invoice before you pay. International: Worldwide shipping available. See Shipping and Payments tab for details. International buyers please note that your country's customs department may add additional charges to process your package. We are unable to anticipate these fees and advise you to research your country's customs regulations before you bid. Thank you. Email info@edgetechnologyproducts.com Phone(520)299-1185 Vise Jaw Stop Photo Gallery Related Products by Edge Technology Products Please take a moment to check out the other high quality machinist gages and tools that we offer. Click the button below to go to our Ebay Store.
Buy It Now
Condition: Used Location: Roanoke, United States Table Travel X Axis: 33”. Table Travel Y Axis: 12”. UsedBRIDGEPORT MODEL SERIES I KNEE MILL. Table: 9” x 48”. When you buy from Select Machine you are ... morenot only buying from a reputable dealer but also a sales and service staff with well over two hundred years of combined experience.
Buy It Now
Condition: Used Location: Tempe, United States Thousands of Used Metalworking and Plastic Machines& New Machine Tools Photos, Full Descriptions and Prices- Fast& Easy About Us Shipping Payments& ... moreCheckout FAQs Our Inventory Home CNC Machines Manual Lathes. Mills, Drills, Saws Grinders. Hones, Finishing Fabricating Equipment Presses& Feeds Boring Mills Automatic Screw Machines EDMs Inspection Equipment Air Compressors Plastic Machinery Planers& Planer Mills Broaches& Keyseaters Shapers& Slotters Tooling& Accessories Welding Equipment Wire& Fastener Ovens. Furnaces& Environmental Misc Metalworking Gear Machinery Material Handling Misc Non-Metalworking 18" X 2HP Spdl Bridgeport Explorer CNC VERTICAL MILL. Bridgeport DX-32 Ref# 150636 iammdna XMVCNC BRIDGEPORT THREE-AXIS CNC VERTICAL MILLING MACHINE MODEL: EXPLORER I. S/N EXP 079, NEW 1995 SPECIFICATIONS: OVERALL SIZE OF TABLE. 16-1/8" X 42" TABLE WORKING SURFACE. 12-1/2" X 34" NUMBER OF T-SLOTS. 3 ON 4-3/8" CENTERS RANGE: LONGITUDINAL(X) 18" CROSS(Y) 12" VERTICAL. KNEE(MANUAL) 14-1/2" QUILL(Z) 5" THROAT DISTANCE. 14-1/2" DISTANCE. TABLE TO SPINDLE- UP AT GAGE LINE. 6.37" MAXIMUM UNIFORM TABLE LOAD. 300 LBS. INFINITELY VARIABLE SPINDLE SPEEDS. TWO RANGES. 60-4.200 R.P.M. SPINDLE TAPER. 30 QUICK-CHANGE FEED RATE. ALL AXES. 0.1-250 I.P.M. FEED INCREMENTS. 0.1 I.P.M. JOG RATE. 150 I.P.M. RAPID TRAVERSE RATE. ALL AXES. 250 I.P.M. APPROXIMATE WEIGHT. 3.150 LBS. APPROXIMATE DIMENSIONS: F-B. 64" L-R. 64" HIGH. 87" EQUIPPED WITH: BRIDGEPORT#DX-32. DOS BASED, 32 BIT PC CONTROL w/ NUMERIC KEYPAD AND FUNCTION KEYS WHICH ARE LINKED TO A COLOR-CODED ON SCREEN DISPLAY. FULL FEAT
Buy It Now
Condition: Used Location: Santa Ana, United States Feed Rate ( X – Y, Axis, Variable ): 0.1 – 250 Ipm. Positioning Speed ( X – Y Axis ): 250 Ipm. Vertical Knee Travel: 14.5″. Floppy Disc Drive. Bijur Auto ... moreLube System. Table size: 9″ X 48″. Pristine And Cleaned Ways.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. Milling Machines. Pneumatic Indexing ... moreTable, Brown & Sharpe No. 22 5″ Vise. Bridgeport Series I 9" x 48" Variable Speed Milling Machine w/ Newall DP700 DRO.
Buy It Now
$15.00 Shipping Condition: New Location: Eagle, United States Untitled Document Description Item: Pro Tram System(Model: 01-000) Condition: New in Box. Specifications Square the head of a milling machine quickly ... moreand easily Simply lower unit to table and adjust the head until both indicators read the same Sized perfectly to fit the bed of a 6" vise allowing the head to be trammed to the vise instead of the table Can be used with a sine bar or sine plate to adjust the head to precise angles Calibration procedure accounts for any error introduced by worn collets Guaranteed to be equal to or better than any other tramming method or spindle squaring device available Large 2.2” easy to read indicator face Indicator graduations are 0.001" 0.0005" version available) Shank diameter is 1/2" 3/8" version available) Indicator repeatability of 0.0002” Body made from red anodized aluminum Includes calibration gage and padded case, Also available is our Mini Pro Tram System designed specifically for smaller Table Top and Mini mills. Pro Tram System The Pro Tram by Edge Technology Products makes the process of tramming your mill fast. Easy and accurate. Tramming is the process of squaring the head of your mill to the table. Most machinists know that if your mill is not trammed properly, surface finishes will be poor and parts will not be flat or square. Most machinists also know that conventional tramming techniques can be tedious and time consuming. The Pro Tram solves these issues allowing you to tram your mill quickly and accurately. To use the Pro Tram simply lower the unit down onto the table and adjust the head until both indicators read the same number. Repeat this process for the opposite axis and you are done. The Pro Tram is also sized perfectly to fit the bed of a 6 inch vise allowing you to tram the head to the vise instead of the table. If you want to spend less time tramming your mill and more time machining parts then you need the Pro Tram by Edge Technology Products. Protected by Patent#8266810 Other patents pending. Payment& Shipping Payments A
Buy It Now
$8.00 Shipping Condition: New Location: Phoenix, United States Fits Bridgeport and others with a 9-cog interface, Tool has. 625" center bore, 1-1/2" deep. "This is the most simple and functional tool. I have several ... moredifferent operations I perform on my mill and the table has to move a great deal up and down.
Buy It Now
$850.00 Shipping Condition: Used Location: Broomfield, United States Sony Millman LH30-2 Digital Scale. Bridgeport Hartford CNC Milling Machine. Wen Ding Power Feed for X-axis (can be turned off and manually adjusted). ... moreUnit shows signs of prior use - oil residue, shavings, rust.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. Milling Machines. Bridgeport J-Head ... moreVertical Milling Machine w/ Sony 2-Axis DRO, Servo Power Feed.
Buy It Now
Condition: Used Location: Lenapah, United States
Buy It Now
Condition: Used Location: Noblesville, United States BRIDGEPORT EXPLORER CNC VERTICAL MILL WITH TOOLINGUnit will need to be picked up. Needs power supply.
Buy It Now
Free Shipping Condition: Used Location: Bristol, United States MOTORS AND SOME BRACKETS JUST WHATS IN THE PHOTOS CAME FROM A 3 AXIS BRIDGEPORT WITH CENT CONTROLLER
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: United States Precision Vise stop. Minimum Clamping Maximum Clamping Key Features.
Buy It Now
Condition: Used Location: Louisville, United States Bridgeport Series 1 EZ Trak Vertical Mill. 3 Axis CNC. Vertical travel of knee: 14". New Updated Software w/USB Port. New Static Hard Drive. New Motherboard. ... moreNew Keypad. Approximate weight: 3,000 lbs.
7d 6h 52m 27s 0 bids
$295.00 Now
$16.10 Shipping Condition: New – Open box Location: Tijeras, United States DRO readout arm. 3 axis DRO unit. Mounting brackets. 17 3/4 scale.
Buy It Now
$20.00 Shipping Condition: New Location: Taylorsville, United States HI YOU ARE LOOKING AT A POWER DRAW BAR FOR A VARIABLE SPEED R8 COLLET IMPORT AND BRIDGEPORT TYPE MILLING MACHINE. JET. MSC, ATRUMP, WT TOOL, ACRA, ACER, ... moreCHEVLAIR, ENCO, TRAVERS, SUPERMAX, AND MANY MORE. THE MOST SIMPLE AND ECONOMICAL POWER DRAWBAR OUT THERE. IT WORKS FROM AIR PRESSURE 90 PSI MAX. YOU JUST PULL DOWN ON THE HANDLE AND MOVE IT LEFT OR RIGHT TO LOOSEN OR TIGHTEN THE DRAW BAR, LET GO OF THE HANDLE AND IT RETURNS TO TOP AUTOMATIC. A HUGH TIME AND AGGRAVATION SAVER NO LOST TIME LOOKING FOR YOUR WRENCH OR HAMMER. MAIN BODY MADE OF 6061 ALUMINUM, MAIN FRONT SLIDE IS MADE WITH STEEL ROD AND NYLON BUSHING, FOR LONG LIFE AND TO DAMPEN ANY VIBRATION FROM THE HEAD. ONE SCREW REMOVES TOP PART TO GIVE ACCESS TO DRAW BAR. CAN BE MOUNTED IN MANY POSITIONS AROUND THE HEAD TO FIT YOUR OWN PREFERENCE. HANDLE FULLY ADJUSTABLE TO FIT YOUR PREFERENCE AND TO TAKE UP ANY WEAR THAT MIGHT HAPPEN OVER TIME. USES ORIGINAL DRAWBAR SO NO SPECIAL DRAW BAR TO BUY. COMES ASSEMBLED COMPLETE WITH IMPACT WRENCH READY TO MOUNT ON YOUR MILL AND USE. IF YOUR COLLET STICKS IN THE SPINDLE RETURN THE IMPACT TO THE TOP AND BRING IT DOWN AND STRIKE THE DRAWBAR AS YOU WOULD WITH A HAMMER. THERE IS ALSO A REGULATOR BUILT IN THE IMPACT WRENCH TO KEEP FROM OVER TIGHTENING THE DRAWBAR. WE DESIGNED THIS POWER DRAW BAR IN OUR SHOP AND HAVE SOLD OVER 400 UNITS WITH GREAT RESULTS PLEASE CHECK OUR EBAY FEEDBACK ALL OF THE MAIN BODY IS MADE AND ASSEMBLED IN OUR SHOP HERE AT M&T MACHINE, TAYLORSVILLE N.C. 28681 USA. WE DEVELOPED THIS POWER DRAWBAR IN OUR SHOP AND HAVE USED THIS TYPE POWER DRAW BAR IN OUR SHOP FOR MORE THAN 10 YEARS WITH NO PROBLEMS. BEWARE THERE ARE INFERIOR COPIES OUT THERE SO PLEASE GET THE ORIGINAL. WE OFFER A FULL 30 DAY RETURN POLICY IF NOT FULLY PLEASED WITH THE TOOL RETURN IT FOR A FULL REFUND. ANY QUESTIONS CALL 828-632-1500 HOME. PLEASE CHECK OUR EBAY FEEDBACK AND PLEASE LOOK AT OUR EBAY STORE WE HAVE OTHER MACHINE SHOP TOOLS FOR SALE.AS WELL AS POWER DRAWBARS FOR STEP PULLEY HEADS THANK YOU VERY MUCH FOR LOOKING TODD AND S
Buy It Now
Condition: Used Location: Stone Mountain, United States Gold International Machinery Corporation | Bridgeport Vertical Milling Machine"J" Head- S/N 9487 Our Inventory Number: 6772-470 Technical Specifications: ... more230V/3PH/60HZ, S/N 9487, 1 HP Motor, 1800 RPM, Table size: 9" x 42" Spindle speeds: 80-2720 RPM, Vertical travel of knee: 12" Longitudinal table travel 20" Cross travel: 14" R8 Taper, Quill travel: 5" Overall dimensions: 50" x 57" x 84"h, Machine weight: 2100 lbs, This item is in very good condition! We can palletize. Cover and load this item for an additional $245. We will load your truck for free from our adjustable loading dock(not crated) Thank you for taking the time to visit our eBay auctions. Our company is a third generation family owned machine dealer with over 50 years experience in the field. We’re conveniently located on the East Coast between Boston and New York. We have a staff of professionals with a broad range of technical and international marketing skills. All dedicated to keeping Gold International on the cutting edge of the marketplace by offering State-of-the-art equipment, technology, and complete service. We offer machinery both New and Second Hand. Our 85.000 square foot Showroom/Warehouse facility is located at the Foot Of Exit#26 off Interstate Route 95 North in Pawtucket. Rhode Island. We are always ready to serve our customers. Our visibility and strength in the marketplace is not accidental, but rather occurs by careful design. Our company representatives attend trade shows in Europe, the Far East and the Americas to maintain our leadership position by channeling our energies to the constant but ever-changing process of finding, cultivating and satisfying our clientele’s machinery and equipment needs. If you should have any questions or concerns about this item. Please contact us before placing a bid. We are always available to handle your requests. We can be reached directly by phone during normal business hours(9am-5pm EST) Monday through Friday at 1-800-619-GOLD. Please ask t
3d 5h 12m 12s 0 bids
$3700.00 Now
Condition: Used Location: Kingman, United States I have two machines Both are very clean great machines. They are in dry storage now. I can help on this end with a fork lift! Power Consumption (KW): ... moreThe machine requires 440V 3-phase power with 20-AMP breakers.
Buy It Now
Free Shipping Condition: New Location: Perth Amboy, United States Alternatively, set the device to automatic constant speed mode for hands-free operation, making your milling tasks a breeze. Equipped with Gleason spiral ... morebevel gears, our milling machine power feed ensures a stable transmission ratio, low noise output, high transmission efficiency, and excellent load-bearing capacity.
Buy It Now
Condition: Used Location: Stone Mountain, United States 3D Printers Air Compressors Air Cooling & Heating Equip. Benders Boring Mills Broaches Chemical & Processing Equip. Milling Machines. Bridgeport J Head ... more9" x 42" Vertical Milling Machine. Bridgeport M Head 9" x 32" Vertical Milling Machine w/ Pneumatic Indexing Tab.
$265.99 Shipping Condition: New Location: China Modle：B132. After the spindle is replaced, the work effect is as new. Total length：545mm.
Buy It Now
$46.28 Shipping Condition: Used Location: Saint Charles, United States Bridgeport Mill Profiling Tracing Attachment - Very Rare - for 4 inch spindleVery rare attachment for Bridgeport mill. This is for the Bridgeport Profiling ... moreAttachment. Used for tracing or duplicating previous work.This Bridgeport Mill Profiling Tracing Attachment is a high-quality tool for your mill. If you are a Bridgeport "collector", you may not have this yet.I believe Bridgeport made a PM-1 model for M heads and a PJ-1 model for J head mills. I do not know much about Bridgeport. If you know which one this is, I would greatly appreciate a message, so I can add the detail to my listing. Thanks!!
Buy It Now
Condition: Used Location: Louisville, United States Bridgeport EZ-Trak II 2-Axis CNC Knee Mill Manufacturer: BridgeportModel#: EZ-TRAK SERIES IIAge: 1999New EZ-Trak CNC Controller w/15" LED Screen New Updated ... moreMotherboardNew Static Hard DriveNew USB DriveSpindle Drive: 2 HP Variable Speed SpindleSpindle Speeds: 60 - 4,200 RPM VariableTable Size: 11" x 58" T-Slotted Work TableMachine Travels: (X/Y) 32" / 15"Quill Travel: 5"Knee Travel 12"Spindle Taper: 30-Taper Kwik SwitchAutomatic Lube System: BijurKnee air power assist230 Volt, 3-PhaseApproximate Machine Dimensions: 84.00"L x 86.00"W x 90.00"HApproximate Weight: 4000.00 lbs.Over $6000 of Kwik Switch 30 taper tooling included
Buy It Now
Condition: Used Location: Bradenton, United States Milling Machine. BRIDGEPORT SERIES 1 Vertical Milling Machine #GMT-3478 Reference # GMT-3478 Model # Series 1 Serial # 440260188X Table working surface- ... more9” x 42” Number of t-slots- 3 Ranges: Longitudinal (X)- 26” Cross (Y)- 11.5” Vertical, knee – 15” Quill (Z)- 5” Maximum/Minimum distance, spindle nose to table- 22-1/4"/ 6-1/2" Maximum/Minimum distance, centerline of spindle to face of column - 18-3/4"/ 6-3/4" Maximum uniform table load- 300 Lbs.
Buy It Now
Condition: Used Location: Lebanon, United States 9” Riser Block. Knee Travel: 16″. Table Size: 9″ x 48″. Cross Travel: 12″. One Shot Lube. Power Draw Bar. X & Y Programable, DRO on Quill. Quill Travel: ... more5″.
Buy It Now
$8.25 Shipping Condition: New Location: Boring, United States The spindle square is adjustable with 3/8 holes for 3-6". It can be used to tram on multiple vise sizes, and machines such as your mill, drill press, ... moresine bar and lathe. We built these as there wasn't square on the market that was universal to different vise sizes or allowed you to change indicators easily or use your own.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Milling Machine Parts R8 Spindle Assembly CNC Milling New Description: Suitable for most bridge and vertical milling machines Model: R8 Total length: ... more540mm After changing the main shaft, the working effect is restored more smoothly than before Installation steps: * Spindle dust cover first * Bearings are matched * Put on bearings and spacer rings * Put on another pair of bearings * Set of sun tablets *fasten the screw nut * Put on 6206 bearing and snap on the retaining ring Note: This installation step only provides the reference for the installer, and cannot be used as a basis for accuracy. If you need to achieve a certain accuracy, you need to ask a professional to install and debug. Packing list: 1 * Milling Shaft.
Buy It Now
$15.00 Shipping Condition: New Location: Boring, United States The spindle square is adjustable with 3/8 holes for 3-6″. It can be used to tram on multiple vise sizes, and machines such as your mill, drill press, ... moresine bar and lathe. We built these as there wasn’t square on the market that was universal to different vise sizes or allowed you to change indicators easily or use your own.
Buy It Now
$8.60 Shipping Condition: Used Location: Apollo Beach, United States Brand new replacement Ball Crank Handle. Fits on most mills. Including Bridgeports and Bridgeport style mills. Bore = 5/8" and Keyway width = 1/8" ... more3mm) Length= 7-3.8" Please call us if you have any question at 714-632-9701. Info@aceronline.net You can pick up from Anaheim. California or Piscataway, New Jersey or we will ship via UPS Ground. Anaheim Office 1062 N. Kraemer Place Anaheim. CA 92806 Piscataway Office 244 N. Randolphville Road Piscataway. NJ 08854 www.aceronline.net This item might be out of stock. If it is out of stock. The lead time is approximately 6~8 weeks. Here are your options if the item is out of stock: 1. You can wait for the item to come in in the 6~8 weeks time frame. or 2. We can cancel your order and get a full refund of your money. Payment Supra Machine Tool accepts: PayPal. Visa, Master Card, American Express, Money Orders, Cashier Checks, Wire Transfer as payment of goods purchased in our store. Please send payment to 1062 N. Kraemer Place, Anaheim, CA 92806) All payments must be received within 7 business days. Bidders can call 714-632-9701 or info@aceronline.net for further information. All buyers residing in California add 8.75% sales tax. Shipping and Handling Buyer pays the Shipping charge based on UPS Ground Shipping Charges. Orders being shipped to P.O. Boxes will be delivered by United States Postal Services(USPS) Note: Weight restrictions may apply in some cases. Buyers can check for shipping rates at www.usps.gov) Orders under 150 lbs. can be shipped by U.P.S. Freight prepaid or collect. Orders above 150 lbs. will be shipped by freight carrier. Supra Machine Tool offers a group of carriers that can quote you with an estimate of shipping charges for all items. Check www.conway.com. Www.roadway.com. Estimated delivery time by UPS is from 2 to 6 business days from the time the order is processed. International buyer pays the actual shipping charge + $5.50-$7.50 handling fees. International shipments of 150 lbs or more can be made by Skyworld International. Buyers
Buy It Now
$71.52 Shipping Condition: New Location: Eastlake, United States SERVO ORION relay board with 16 relays. SERVO PRODUCTS CO. Enclosure for CNC panel and operation panel. Mounting arm. l Tool offset.
Buy It Now
Condition: Used Location: Louisville, United States NEWALL 2 AXIS DIGITAL READOUT. KURT 6" VISE. THIS IS A BRIDGEPORT 2HP VARIABLE SPEED HEAD with "KWIK CHANGE" SPINDLE MOUNTED TO A IMPORT CNC KNEE MILL ... moreBASE. I PERSONALLY THINK IT'S A "LAGUN BASE". SPINDLE TAPER..
Buy It Now
Condition: Used Location: Millinocket, United States Bridgeport Milling Machine Series II - Head only-2hp. This item has been in storage for a few years. We upgraded and no longer need it. Good working condition ... morewhen last used. Item is sold as is. Feel free to message with any questions.
Buy It Now
Free Shipping Condition: New Location: San Jose, United States Upgrade your milling game with brand new Bridgeport Mill Preventive Maintenance Kit Package BP 120640002HP from Hardinge Co. This manual machine is perfect ... morefor your machining needs, whether you are a professional or a DIY enthusiast. Made in the United States, it boasts a brand of Hardinge and a model of Bridgeport BP 120640002HP. With its CNC, Metalworking & Manufacturing category, this milling machine is an industrial-grade tool that can handle all your metalworking equipment needs. It is perfect for milling, with its machining centers & milling machines category. Take your metalworking to the next level with this high-quality machine that is sure to impress.
Free Shipping Condition: New Location: Chino, United States Description: This is a high-quality brass grinding straight mold tooth, very suitable for TON-E, KENF, ALSGS, SBS, ALIGN and other models, easy to disassemble, ... morestrong and durable. What's Included: 1X spur gear Features&Highlights: Inner hole: 16mm Keyway: 3mm Suitable for TON-E, KENF, ALSGS, SBS, ALIGN Material: Bronze .
Buy It Now
Free Shipping Condition: New Location: China Suitable for 3#4# milling machine. B74-96 Mill- Parts. Color :Black.
Buy It Now
Free Shipping Condition: New Location: China Can fit Bridgeport, Acer, and Taiwanese all machines. Size : 400mm x 600mm.
Buy It Now
Condition: Used Location: Pomona, United States CNC or Manual Operation. 2 Axis CNC on X & Y. Feed Rate (X-Y Axis, Variable) 0.1-100 IPM. Positioning Speed (X-Y Axis) 100 IPM. Vertical Knee Travel 16". ... moreEQUIPPED WITH Weight 2300 Lbs. Throat Distance 6 3/4" - 18 3/4".
Buy It Now
$65.00 Shipping Condition: Used Location: Sterling Heights, United States Low hour prototrak mill motor. Nothing wrong with motor we just swapped all the prototraks to variable speed baldor setups. This motor has very low hours ... moreand is very very clean. No pulley. What you see is what you get.
Buy It Now
Condition: Used Location: Orange City, United States Greenway Product Number: 10906. Model: EZ Trak DX. Machine weight... 2,800 LBS. 2 HP main motor. Auto lubrication. Stop/Go switch. Acur-rite quill scale.
Buy It Now
Free Shipping Condition: New Location: China Suitable for:Taiwan milling machine, Taichen milling machine, turret milling machine, etc.
Buy It Now
Free Shipping Condition: New Location: China Can fit Bridgeport, Acer, and Taiwanese all machines. Size : 400mm x 600mm.
Buy It Now
Free Shipping Condition: New Location: China Bridgeport Milling Machine Part Forward Reversing Drum Switch 15 Amp 380V 1pc.
Buy It Now
Condition: Used Location: Rochester, United States Type: CNC Milling Machine. Make: Bridgeport. Motor HP: 2. Motor Electric: 220/230/440/460V 3 Phase. Serial: 134400. Motor RPM: 1415.
Buy It Now
Free Shipping Condition: New Location: Perth Amboy, United States Brand new replacement Ball Crank Handle. Fits on most mills. Including Bridgeports and Bridgeport style mills. Bore = 5/8" and Keyway width = 1/8" ... more3mm) Length= 7-3.8" Please call us if you have any question at 714-632-9701. Info@aceronline.net You can pick up from Anaheim. California or Piscataway, New Jersey or we will ship via UPS Ground. Anaheim Office 1062 N. Kraemer Place Anaheim. CA 92806 Piscataway Office 244 N. Randolphville Road Piscataway. NJ 08854 www.aceronline.net This item might be out of stock. If it is out of stock. The lead time is approximately 6~8 weeks. Here are your options if the item is out of stock: 1. You can wait for the item to come in in the 6~8 weeks time frame. or 2. We can cancel your order and get a full refund of your money. Payment Supra Machine Tool accepts: PayPal. Visa, Master Card, American Express, Money Orders, Cashier Checks, Wire Transfer as payment of goods purchased in our store. Please send payment to 1062 N. Kraemer Place, Anaheim, CA 92806) All payments must be received within 7 business days. Bidders can call 714-632-9701 or info@aceronline.net for further information. All buyers residing in California add 8.75% sales tax. Shipping and Handling Buyer pays the Shipping charge based on UPS Ground Shipping Charges. Orders being shipped to P.O. Boxes will be delivered by United States Postal Services(USPS) Note: Weight restrictions may apply in some cases. Buyers can check for shipping rates at www.usps.gov) Orders under 150 lbs. can be shipped by U.P.S. Freight prepaid or collect. Orders above 150 lbs. will be shipped by freight carrier. Supra Machine Tool offers a group of carriers that can quote you with an estimate of shipping charges for all items. Check www.conway.com. Www.roadway.com. Estimated delivery time by UPS is from 2 to 6 business days from the time the order is processed. International buyer pays the actual shipping charge + $5.50-$7.50 handling fees. International shipments of 150 lbs or more can be made by Skyworld International. Buyers
Buy It Now
Free Shipping Condition: New Location: Ontario, United States US 2Axis Digital Readout DRO Display 250&1000MM Linear Scale TTL Glass Ruler Kit for Milling Lathe Machine Benefit : (1)Digital display to eliminate backlash ... moreand improve precision (2)Advanced trigonometric calculation so to accomplish a perfect project (3)11.6”wide display to offer excellent long-distance viewing (4)DRO providing a two axis display with pitch circle calculator, diameter/radius conversion, absolute and incremental toggle, and inch metric toggle (5)Digital readout kit can avoid wasting weeks to check machine precision (6)Lifetime free technical support, 2Years warranty, 30-day return Application : This DRO kit is commonly fitted to machines , especially for metal working — lathes, cylindrical grinders, milling machines, surface grinders, boring mills and other machine too.
Buy It Now
Free Shipping Condition: New Location: China Suitable For :3# 4# Milling Machine. Suitable For Turret Milling Machines. Mill Feed Handle. 12 Hole Bracket.
Buy It Now
$59.05 Shipping Condition: Used Location: Watsontown, United States This Bridgeport milling machine tailstock is in excellent shape and has a center height of 8 inches. It is perfect for drilling and milling tasks and ... moreis suitable for use in the CNC, Metalworking & Manufacturing industry. The brand of this machine is Bridgeport and it is a model that is tailored specifically for milling machines. If you are looking for a reliable and efficient tailstock for your milling machine, this one is definitely worth considering. Its condition is impeccable, making it an excellent choice for those who value quality and performance. Get your hands on this machine today and take your machining tasks to the next level!
Buy It Now
$400.00 Shipping Condition: Used Location: Carlyle, United States The system comes with everything needed to convert your Bridgeport manual milling machine into a two axis CNC. This system is fully functional when removed. ... moreAlthough I am happy to work with a customer to get it installed properly via phone calls and video conferencing consultation, the customer is ultimately reliable for proper install.Jon.
Buy It Now
Condition: Used Location: Lake Elsinore, United States MIGHTY VIPER PRO-3210 CNC VERTICAL BRIDGE MILL. Make: Mighty Viper. CNC Machines. New & Used CNC. CNC LATHE / TURNING CENTERS. CNC MILLING MACHINES. VERTICAL ... moreMACHINING CENTERS. HORIZONTAL MACHINING CENTERS.
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States Specification: Color: Silver material: metal Packing size: 18.3*15*7.6cm Package weight: 0.7kg Description: Milling machine accessories clutch ring Milling ... moremachine M3/M4 accessories Milling machine slow gear clutch Suitable for most milling machines The package includes: 1X milling machine slow gear clutch.
Buy It Now
Condition: Used Location: Fairfield, United States Chevalier Vertical Milling Machine. Feel free to inspect in Bridgeport, CT 06607. Also, the "Yoke or Feed Nut Bracket" broke. It still needs a few holes ... moredrilled and tapped - the ones that hold the nuts.
Buy It Now
Free Shipping Condition: New Location: China Fit for bridgeport machine Grank Handle. Thread Size :3/8. Before you open a case.
Buy It Now
Free Shipping Condition: New Location: China Handwheel material: high quality plastic. Suitable For Most Milling Machines. Part #: MP6210.
Buy It Now
Free Shipping Condition: New Location: United States Milling Machine Parts R8 Spindle Assembly CNC Milling New Description: Suitable for most bridge and vertical milling machines Model: R8 Total length: ... more540mm After changing the main shaft, the working effect is restored more smoothly than before Installation steps: * Spindle dust cover first * Bearings are matched * Put on bearings and spacer rings * Put on another pair of bearings * Set of sun tablets *fasten the screw nut * Put on 6206 bearing and snap on the retaining ring Note: This installation step only provides the reference for the installer, and cannot be used as a basis for accuracy. If you need to achieve a certain accuracy, you need to ask a professional to install and debug. Packing list: 1 * Milling Shaft.
Buy It Now
Free Shipping Condition: New Location: China Model ：7207DB + 6206. Suitable for R8 spindle. Suitable for most Taiwan milling machines. The oil seal color on the bearing is random.
Buy It Now
$149.99 Shipping Condition: New Location: China BRIDGEPORT Type Mill Part, J Head Milling Machine RAM Adapter M1187. Model ： M1187. Suitable for most milling machines.
|
|
|
|
Bridgeport 2 Axis CNC Milling Machine Vertical Mill Prototrak AGE2 Series 1 2 Hp
You are bidding on a Bridgeport Series 1 Mill w/ Prototrak 2 Axis CNC Control. This is a very nice machine that I have done extensive work to get it to this condition. Variable Speed head has been redone within the last 10 hrs. of use. Prototrak Pendant was replaced with factory rebuilt unit 6 months ago. This machine has more options and equipment than any machine you will buy from a dealer. INCLUDES: Prototrak AGE 2 2 Axis CNC Control w/ Floppy Disk Drive& Remote Stop/Go Switch Acu-Rite X-Y.0002" Glass Scale Feedback- Lip Seal in Scales was just replaced. Acu-Rite Z Axis(Quill) Glass Scale- Reads on AGE2 Control. Kurt D675 Vise w/ Adj. Stop and 5/8" Keys on Bottom for Quick Alignment. New Rubber Way Covers for Y& Knee Axis Table T-Slot Covers Align Knee Feed Kurt BR1000 Automatic Power Drawbar Adj. Chip Shield- Swings ... moreout of the way Moffatt Flexible Arm Machine Lamp- 100W Quick Adjust Nut on Quill Stop Quick Adj. Twin Grip Quill Handle Collet Rack Shop Made Holders for RSG Switch and Vise Handle. Specifications: 2 Hp Variable Speed Head R-8 Spindle Taper 9"x42" Table Voltage- 220/440/3/60- I run this@ 220V on a Static Phase Convertor. Weight- Approx. 2.800# This machine is available after 4/5/13 when my new machine arrives. I will load on your truck or trailer for free. If you want this put on a Heavy Duty Skid w/ sides and prepped for shipping by a Common Carrier there will be a charge of $ 325.00. You are welcome to inspect this machine under power on weekends or at night. Please no lowball offers. I know what this is worth and don't have time to deal with people that do not. Call 262-719-0232 or email with any questions.
|
|
|
1994 BRIDGEPORT EZ-TRAK DX Automatic / CNC / Manual Mill 3HP 9"x48" Chrome Ways
ebay template EZ-TRAK DX 9"x48" CNC/ Manual Mill I TEM S OLD A S P ICTURED This 1994 EZ-TRAK DX has a 2-axis control that comes factory-fit with power feeds on the Series I standard mill. The control is easier to operate than conventional CNC. And far more productive than manual machining. 2D contouring capability lets you machine angles and radii without a rotary table. And it's a tremendous time-saver on repetitive work like bolt hole circles. As you put in the dimensions for each X- and Y- axis move directly from your blueprint. The easy-to-read screen displays and executes them. You can store thousands of individual operations. You can also"teach" the control how to machine the part by moving the table and hitting the"Enter" key at the end of each move to store the machine position. This machine has recently ... morebeen serviced by a technician to ensure it is in good working condition. FEATURES Bridgeport 2-Axis Control Machine operation alternates between automatic and manual Powerfeeds for both X-axis(longitudinal) and Y-axis(cross) 100 ipm Rapid Traverse 3HP DC Motor Chrome Ways Automatic centralized lubrication system SPECIFICATIONS*Specifications subject to verification INSPECTION NOTES: As with any piece of equipment. New or used, this item will require additional inspection after it arrives due to the vibration during transit. We recommend you hire a professional service person to install the machine, test it and perform any necessary service adjustments before putting it in to production. Please refer to the pictures for this item's cosmetic condition. This item is sold as pictured. Shipping Shipping is the responsibility of the buyer; however. Machinery Exchange has a large network of freight carriers to help you find the best price. If you would like a freight quote for this item please click"Contact Seller" or“Ask Question” at the bottom of the listing and provide us with your city, state and zip code. Or contact us via telephone at(818) 718-6734 Machines a
|
|
|
ACCUPRO End Mill Carbide 5/8 for Machinist CNC Bridgeport Gunsmith
One used Accupro solid Carbide End mill. Four Flute, ALTIN, 5/8" dia. of cut, 5/8" shank, 2 1/8" LOC, 4 5/8" OAL Item in the picture is the one you will receive. I do not ship outside the USA PayPal only
|
|
|
Putnam 3/4" Long End Mill HSS for Machinist CNC Bridgeport Mold Tool Die
One used Putnam 3/4" long reach end mill HSS 3/4" dia. of cut. 3/4" shank, 1 5/8" LOC, 3 1/4" depth of cut, 5 1/2" OAL Two flute Item in the picture is the one you will receive. I do not ship outside the USA PayPal only
|
|
|
Proto-trak EDGE Sharp CNC /Manual Vertical Milling Machine Bridgeport Trak Mill
Up for sale is a SHARP LMV Knee Mill with a PROTOTRK EDGE Control Up for sale is a Sharp LMV Kee Mill with a Prototrak Edge Control. It comes with One Shot Lube System. Chromed Quill, Honed Head, Precision Scraped V Ways on Ram, Ground Table with Coolant Trough. Double Saddle Locks,and Adjustable Ram Gib. Here are the specs: Table Size. 9"x 42" Longitudinal Travel. 30" Cross Travel. 12" Vertical Knee Travel.16" Ram Travel.18" Turret Rotation.360° Spindle Speeds(8)64- 4500 Spindle Taper.R8 Quill Travel.5" Motor.3HP. 220/3/60/460 Weight.2.300lbs. This machine has great features to help you be productive without the bells and whistles that make other CNCS more complicated. There are 19 different math helps are available for you to quickly and easily calculate intersections. Points of tangency centers and ... moremore. The most useful features of a DRO are available with the added plus of ballscrews for smooth positive control and motors for jogging. This will be a great machine even if you have never used a CNC before. You can learn the ProtoTrak Edge in a couple of hours. I am including a Self- Training Manual. It is easier to learn and to make parts on a ProtoTrak Edge than it is to use a DRO. You can create part libraries. Safegaurd part programs or share programs between other ProtoTrak machines. I would be happy to demo the machine. If you have an questions please me at 612-803-5414 This is a great machine with everything in great working order and ready to make parts. Can help buyer arrange loading and shipping. Happy Bidding!
|
|
|
End Mill 1/4 Corner Round 3 Flute HSS M42 for Machinist Gunsmith Bridgeport CNC
One Gently Used Hertel 1/4" Corner Rounding End Mill. 3 flute, 3/4" shank HSS M-42 Item in the picture is the one you will receive. I do not ship outside the USA PayPal only ``d.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E%60%60d-13ea1041cf6-0x102-
|
|
|
22"x16"x20" Bridgeport CNC MILL Torq-Cut 22, Vertical Machining Center, 1995
T he machine is in good working order and under power for inspection. 1995 BRIDGEPORT TORQ-CUT 22 Vertical CNC Machining Center 7.5 HP AC Spindle 22 position BT-40 tool changer Table 33” x 14” Travel- X 22” Y 16” Z 20” Software– BOSS DX/32 V4.43/6.86.1G s old with the machine; 2 Accupro vises BT-40 tool holders Installation Manual Operator Manual Programming Manual Serial cable for program transfer BUYER IS RESPONSIBLE RIGGING AND SHIPPING- WILL LOAD ONTO QUALIFIED RIGGERS TRUCK. CASH. CERTIFIED CHECK, CLEARED CHECK.
|
|
|
ATRAX End Mill Carbide 1/2 Long Reach Used for Machinist Tool Die CNC Bridgeport
One used ATRAX Long End mill. Four Flute, 1/2" dia. of cut, 1/2" shank, 2" LOC, 4" OAL. Item in the picture is the one you will receive. I do combine shipping. I do not ship outside the USA PayPal only
|
|
|
SGS End Mill Carbide 1/2 Long Reach Used for Machinist Tool Die CNC Bridgeport
One used SGS Long End mill. Four Flute, 1/2" dia. of cut, 1/2" shank, 2" LOC, 4 1/2" OAL. Item in the picture is the one you will receive. I do not ship outside the USA PayPal only
|
|
|
KURT II PT-800A 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE #1
KURT II PT-800A 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE#1 KURT II PT-800A 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE. THIS UNIT IS IN GREAT SHAPE. All purchases are expected to be payed within 5 business days. Items will be shipped UPS or Fedex Ground. We do not ship to P.O. Box. Buyer will have to pay"duty" if shipped internationally Insurance can be purchased at an extra cost. PLEASE BE ADVISED THAT ALL ITEMS ARE SOLD IN USED CONDITION UNLESS SPECIFIED AS BRAND NEW. ALL ITEMS ARE SOLD AS IS WITH NO WARRANTY. YOU ARE BUYING USED EQUIPMENT AT USED PRICES. WE DO OUR VERY BEST TO DESCRIBE EACH ITEM AND ITS CONDITION. ALL ITEMS ARE SOLD IN GOOD TO GREAT WORKING CONDITION. IF YOU ARE NOT HAPPY WITH YOUR PURCHASE PLEASE CONTACT US BEFORE LEAVING A NEGATIVE FEEDBACK. OUR PHONE NUMBER IS 1 718 698 8400 ... moreWE ARE LOCATED AT 3521 VICTORY BLVD STATEN ISLAND NY 10314. WE ARE OPEN 8AM TO 6PM MON-SAT. YOU CAN CALL US AT 718 698 8400
|
|
|
KURT D-100 10 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE #4
KURT D-100 10 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE#4 KURT D-100 10 INCH MACHINE VISE FOR BRIDGEPORT MILL MILLING MACHINE. THIS UNIT IS IN GREAT SHAPE. All purchases are expected to be payed within 5 business days. Items will be shipped UPS or Fedex Ground. We do not ship to P.O. Box. Buyer will have to pay"duty" if shipped internationally Insurance can be purchased at an extra cost. PLEASE BE ADVISED THAT ALL ITEMS ARE SOLD IN USED CONDITION UNLESS SPECIFIED AS BRAND NEW. ALL ITEMS ARE SOLD AS IS WITH NO WARRANTY. YOU ARE BUYING USED EQUIPMENT AT USED PRICES. WE DO OUR VERY BEST TO DESCRIBE EACH ITEM AND ITS CONDITION. ALL ITEMS ARE SOLD IN GOOD TO GREAT WORKING CONDITION. IF YOU ARE NOT HAPPY WITH YOUR PURCHASE PLEASE CONTACT US BEFORE LEAVING A NEGATIVE FEEDBACK. OUR PHONE NUMBER IS 1 718 698 8400 WE ARE LOCATED ... moreAT 3521 VICTORY BLVD STATEN ISLAND NY 10314. WE ARE OPEN 8AM TO 6PM MON-SAT. YOU CAN CALL US AT 718 698 8400
|
|
|
KURT D-810 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE
KURT D-810 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE KURT D-810 8 INCH MACHINE VISE FOR BRIDGEPORT MILL MILLING MACHINE. THIS UNIT IS IN GREAT SHAPE. All purchases are expected to be payed within 5 business days. Items will be shipped UPS or Fedex Ground. We do not ship to P.O. Box. Buyer will have to pay"duty" if shipped internationally Insurance can be purchased at an extra cost. PLEASE BE ADVISED THAT ALL ITEMS ARE SOLD IN USED CONDITION UNLESS SPECIFIED AS BRAND NEW. ALL ITEMS ARE SOLD AS IS WITH NO WARRANTY. YOU ARE BUYING USED EQUIPMENT AT USED PRICES. WE DO OUR VERY BEST TO DESCRIBE EACH ITEM AND ITS CONDITION. ALL ITEMS ARE SOLD IN GOOD TO GREAT WORKING CONDITION. IF YOU ARE NOT HAPPY WITH YOUR PURCHASE PLEASE CONTACT US BEFORE LEAVING A NEGATIVE FEEDBACK. OUR PHONE NUMBER IS 1 718 698 8400 WE ARE LOCATED ... moreAT 3521 VICTORY BLVD STATEN ISLAND NY 10314. WE ARE OPEN 8AM TO 6PM MON-SAT. YOU CAN CALL US AT 718 698 8400
|
|
|
Series II BRIDGEPORT EZ-Trak DX 3X CNC/3X DRO Vertical Mill (New 1995)
Preowned Series II BRIDGEPORT Three-Axis CNC Vertical Milling Machine With Three-Axis Digital Readout. Model: Series Il EZ-Trak DX, S/N: EZ-2291(New 1995) Table working surface Number of t-slots Range: longitudinal(X) cross(Y) vertical. Knee quill(Z) Maximum distance. Spindle nose gage line to table Maximum/Minimum distance. Centerline of spindle to face of column Maximum uniform table load Ram travel(3) Power quill feeds Infinitely variable spindle speeds. Two ranges Spindle taper Maximum collet capacity X& Y axes manual and automatic positioning rate X& Y axes feedrate range. Infinitely variable Minimum feedrate increment 11" x 58" 3 32" 14.5" 12" 4.4" 17" 22"6" 600 Lbs. 17" 0015. 003, 006 I.P.R. 60- 500 R.P.M. 500- 4.200 R.P.M. Universal Kwik-Switch 200 3/4" 100 I.P.M. 0.1- ... more100 I.P.M. 0.0001" Equipped With. BRIDGEPORT three-axis CNC control with 9" monochrome conversational display. Simultaneous circular or linear interpolation. Absolute and incremental programming, automatic corner rounding. Mathematical help mode, canned cycles for machining arcs. Diagonals, circles, bolt hole patterns, pocket milling and more, cutter diameter compensation. And English/metric conversion. Control has a hard drive and disc storage. Part program loading is done through RS-232 port or floppy disc drive. Full contouring capability Three-axis digital readout during manual operations Ballscrews on both X& Y axes as well as quill SEM DC servo motors on all axes Box-type chrome ways Remote start switch BIJUR automatic lubrication system Work light 2 H.P. 3/60/220-440 volt spindle drive motor and electrical controls Machine is wired for 460 volt operation. Approximate Weight: 3.900 Lbs. Approximate Dimensions: 84" L-R x 78" F-B x 86" H, Condition: Excellent, We Ship Worldwide- F.O.B. Truck. Hauppauge- Long Island, NY)
|
|
|
Niagara 3/4" Ball Nose End Mill HSS for Machinist CNC Bridgeport Mold Tool Die
One used Niagara 3/4" ball nose end mill HSS 3/4" dia. of cut. 3/4" shank, 3/4" Ball, 1 3/8" LOC, 3 7/8" OAL Two flute Item in the picture is the one you will receive. I do not ship outside the USA PayPal only
|
|
|
CNC MILLING MACHINE BRIDGEPORT TYPE KNEE MILL 9 x 42 TABLE
ALLIANT 3 HP KNEE MILL WITH BALLSCREWS ON X AND Y AXIS. DC SERVOS WITH 2500 CPR US DIGITAL ENCODERS ON THE X AND Y AXIS. 3 PHASE INCLUDES A 7 HP ROTARY PHASE CONVERTER. SOME TOOLING R8 COLLETS, R8 1/2 INCH END MILL HOLDER, DRILL CHUCK, HANDWHEELS ON BOTH X AND Y AXIS. HAS SOME NOISE IN THE VARIABLE SPEED PULLEYS.
|
|
|
Bridgeport CNC Mill 30 NMTB Taper Tool Pre Set Fixture Erickson Tool Co.
Bridgeport CNC Mill 30 NMTB Taper Tool Pre-Set Fixture Erickson Tool Co. Bridgeport#1-57-0480 This is a No.30 NMTB Taper Tool Pre-Setting Fixture that was used with Bridgeport CNC milling machines that used the Erickson Quick Change Tooling and 30 Taper spindle. It is equipped with a 1" travel Starrett micrometer head with a friction thimble. Please see the Erickson tooling drawing for dimensions. This has been unused and sitting on a shelf since the mid 1980's. In excellent condition. Copy of tooling drawing included. The package measures 9" x 14" x 15" high. Will weigh 29 lbs. and will ship via USPS Priority Mail with insurance.
|
|
|
Ball Nose End Mill Lot HSS for Machinist Tool Die CNC Gunsmith Bridgeport
One lot of ball nose end mills. Variety of sizes 1/2" 3/8" 1/4" 3/16" Putnam, Cleveland& other. HSS and a couple of carbide. Item in the picture is the one you will receive. I do combine shipping. But please let me know if you are bidding on multiple items, and if you win multiple items wait till I send an invoice to reflect correct shipping. I accept PayPal only. I do not ship outside the USA. Thanks for looking. Normal 0 false false false EN-US X-NONE X-NONE.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-13f7a2be7ce-0x103-
|
|
|
2000 BRIDGEPORT MILL MILLING MACHINE 3 AXIS CNC ACU-RITE MINT CONDITION
2000 BRIDGEPORT MILL MILLING MACHINE 3 AXIS CNC ACU-RITE MINT CONDITION 2000 BRIDGEPORT MILL MILLING MACHINE 3 AXIS CNC ACU-RITE MINT CONDITION. SERIAL NUMBER BR-281386. 9x48 INCH TABLE. PLEASE TAKE A LOOK AT ALL THE PICTURES. All purchases are expected to be payed within 5 business days. Items will be shipped UPS or Fedex Ground. We do not ship to P.O. Box. Buyer will have to pay"duty" if shipped internationally Insurance can be purchased at an extra cost. PLEASE BE ADVISED THAT ALL ITEMS ARE SOLD IN USED CONDITION UNLESS SPECIFIED AS BRAND NEW. ALL ITEMS ARE SOLD AS IS WITH NO WARRANTY. YOU ARE BUYING USED EQUIPMENT AT USED PRICES. WE DO OUR VERY BEST TO DESCRIBE EACH ITEM AND ITS CONDITION. ALL ITEMS ARE SOLD IN GOOD TO GREAT WORKING CONDITION. IF YOU ARE NOT HAPPY WITH YOUR PURCHASE PLEASE CONTACT US BEFORE LEAVING A NEGATIVE ... moreFEEDBACK. OUR PHONE NUMBER IS 1 718 698 8400 WE ARE LOCATED AT 3521 VICTORY BLVD STATEN ISLAND NY 10314. WE ARE OPEN 8AM TO 6PM MON-SAT. YOU CAN CALL US AT 718 698 8400
|
|
|
BRIDGEPORT DX2 3-Axis CNC EZ-Trak Knee Mill, KwikSwitch 200, Excellent Condition
Bridgeport DX2 3-Axis CNC Knee Mill. Excellent condition. We have operated this machine for ~8 years. It has been regularly serviced and it has been a great machine. With the EZ-Track and Kwik Switch collet system, this machine is fantastic for R&D or small to medium volume production( The following accessories with the purchase: Programmers manual Manual quill handle Knee crank KS200 spanner wrench Z-Axis Hex Key torque wrench"Cool Tool" cutting coolant system A large KS200 tooling package is available at additional cost This machine has the following features: Table working Surface: 11x 58" T-Slots: 3 X-Travel: 32" Y-Travel: 14.5" Z-Travel: 4.4" Knee Travel 12" Air Assist Spindle to Table(max) 17" Spindle to Column(min/max) 6"22" Ram Travel: 17" Spindle Speed(low/high) 60-500 RPM/ ... more500-4200 RPM Spindle Taper: Universal Kwik Switch 200 XY Axis Speed(max) 100 IPM Included Equipment BRIDGEPORT three-axis CNC control with 9" monochrome conversational display. Simultaneous circular or linear interpolation. Absolute and incremental programming, automatic corner rounding. Mathematical help mode, canned cycles for machining arcs. Diagonals, circles, bolt hole patterns, pocket milling and more, cutter diameter compensation. And English/metric conversion. Control has a hard drive and disc storage. Part program loading is done through RS-232 port or floppy disc drive. Full contouring capability Three-axis digital readout during manual operations Ballscrews on both X& Y axes as well as quill SEM DC servo motors on all axes Box-type chrome ways Remote start switch BIJUR automatic lubrication system Work light 2 H.P. 3/60/220-440 volt spindle drive motor and electrical controls Machine is wired for 220 volt operation(440vac components also included) Weight: 4000 lb. Dimensions(approximate) 84"W. 86"H, 78"D. Condition: Excellent. Location: Santa Rosa. CA. Shipping: Local pickup is preferred. We can skid this item and ship it to you nationwide. B
|
|
|
Series I BRIDGEPORT 3X CNC/3X DRO Vertical Mill (New 1986, Retrofitted in 1995)
Preowned Series I BRIDGEPORT Three-Axis CNC Vertical Mill. Series I S/N 246335(New 1986, Retrofitted in 1995) Table working surface Number of t-slots Range: longitudinal(X) cross(Y) vertical. Knee quill(Z) Maximum/Minimum distance. Spindle nose to table Maximum/Minimum distance. Centerline of spindle to face of column Maximum uniform table load Ram travel Head tilt. Left and right Head tilt. Front to rear, each way(3) Power quill feeds Infinitely variable spindle speeds. Two ranges Spindle taper Minimum feedrate increment 9" x 48" 3 29.5" 11.5" 15" 5" 18-1/4" 2-1/2" 18-3/4" 6-3/4" 300 Lbs. 12" 90 degrees 45 degrees.0015. 003, 006 I.P.R. 60-500 R.P.M. 500-4.200 R.P.M. Universal Kwik-Switch 200 0.0001" Equipped With ProtoTrak MX3 three-axis CNC control with CRT(display box is new in ... more2012) Floppy disc drive. And RS-232 port DC servo motors and ball screws on all axes Three-axis digital readout during manual operations Dovetail-type chrome ways BIJUR lubrication system 2 H.P. 3/60/230-460 volt spindle drive motor and electrical controls Machine is wired for 460 volt operation. Approximate Weight: 2.000 Lbs. Condition: Very Good, We Ship Worldwide- F.O.B. Truck. Hauppauge- Long Island, NY)
|
|
|
Bridgeport CNC Vertical Mill 3 Axis Series 1
I am listing this for my dad. Please contact him(phone number below) for information on mill. Thanks for looking! The Bridgeport Mill is in excellent condition. Bed is 9 x 48 inches. It has a little old oil staining that can be removed with a little elbow grease. All the Bridgeport goodies. Kurt pneumatic tool holder changer. 20 tool holders tool work table. Coolant splash guard. Coolant pump. No cutting tools included. Sn. 2J149189 Installation and maintenance manual. Boss XT parts and operation manual I can load on your truck or trailer with overhead crane. I purchased The mill in 2003. I am the 2nd owner. It came from a small 2 man tool and die shop. We used the mill to make gun parts for 3 years. Then I closed my shop. It has not seen any heavy production work. The only problem was a air leak concerning the tool changer. It was no big ... moredeal and should be simple to fix. But I just never got around to it. You can see the Bridgeport any time. It is still under power. However. I don't know how to operate it. Call Ken Merriman 1-812-849-2784. Buyer responsible for pick up $1000 deposit in 48 hours-rest of payment due in 7 days-payment arrangements thur Ken Merriman please. Machine is for sale locally. I have the right to end auction if needed-Thanks! Posted with
|
|
|
BRIDGEPORT 2-AXIS CNC MILL - 9"x42" SERIES 1 MILLING MACHINE 3-Axis DRO
ebay template Series 1: 9" x 42" Two-Axis CNC Milling Machine with 3-Axis DRO& Knee Travel Powerfeed I TEM S OLD A S P ICTURED This is Bridgeport 2-Axis cnc milling machine equipped with a 2HP Series 1 milling. Drilling, and boring head as well as powerfeed on the knee travel and digital readout for manual quill feed. The capacity of the machine includes right angle milling, drilling, and boring as well as vertical. Ram type construction permits movement of head over the table without rechecking the squareness of the spindle. In and out movement of the ram, through rack and pinion, is effortless. Bridgeport released this milling machine in 1983 or later according to the serial number and as with many Bridgeport. Has withstood the test of time and is in very good working condition with minor signs of wear from age and previous ... moreuse. Please call if you'd like further details or information. Ask for Jerad(818) 718-6734 FEATURES Anilam 2-Axis CNC Control 3-Axis DRO 2HP Spindle Motor Powerfeed on Knee Travel, Kurt Automatic Power Draw Bar, Chrome Ways, 3.5" Floppy Drive One Shot Lube System SPECIFICATIONS Table Size 9" x 42" Longitudinal Table Travel. X-Axis 25" Cross Table Travel. Y-Axis 12" Quill Travel 5" Knee Travel. Z-Axis 16" Ram Travel 12" Throat Distance 6¾" to 18¾" Table to Spindle Nose. Min. 2½" Max. Weight of Workpiece 750 lbs. Spindle Motor 2 hp Spindle Taper R8 Speed Range 60 to 4200 rpm Floor Area 64" x 64" Height 83" Net Weight 2920 lbs. Power 220 Volt. 3 Phase*Specifications subject to verification INSPECTION NOTES: As with any piece of equipment. New or used, this item will require additional inspection after it arrives due to the vibration during transit. We recommend you hire a professional service person to install the machine, test it and perform any necessary service adjustments before putting it in to production. Please refer to the pictures for this item's cosmetic condition. This item is s
|
|
|
Putnam Used Ball Nose 3/4 End Mill 2 flute for Machinist Gunsmith CNC Bridgeport
One lightly used Putnam HSS Ball Nose End Mill. 3/4" dia of cut, 3/4" shank, 4" OAL, Center Cut. Item in the picture is the one you will receive. I do combine shipping. But please let me know if you are bidding on multiple items, and if you win multiple items wait till I send an invoice to reflect correct shipping. I accept PayPal only. I do not ship outside the USA. Thanks for looking. Normal 0 false false false EN-US X-NONE X-NONE
|
|
|
Bridgeport CNC R2E4 Vertical Mill
Bridgeport CNC R2E4 Vertical Mill Specifications: Motor Rating 2 hp Power Rating at Spindle Nose 1- 1.75 hp Taper#30 for Quick Change Holders Rapid Approach Rate(Z-axis) 250 ipm Controlled Downfeed Range(Z-axis) 1-250.0 ipm Drilling Capacity- Mild Steel 3/4" diameter Milling Capacity- Mild Steel 1.5 cu in/min Boring Range to 4 diameter tapping Range#5-40 to 1/2-13 ALL ITEMS ARE SOLD AS IS. WHERE IS stock#4348 BUYER IS RESPONSIBLE FOR ALL FREIGHT ARRANGEMENTS AND COST shipping dimensions: 6' x 6' x 90" approx. 4500 lbs
|
|
|
Machine vise for Bridgeport and CNC milling machines mill
Machine vise for Bridgeport and CNC milling machines mill Machine vise for Bridgeport and CNC milling machines. I sold my milling machine years ago and it has been gathering dust since. I can not find the handle so it is being sold as-is without a handle. Will be shipped UPS but I do reserve the right to use USPS to other than the lower 48 states Payment is expected within 7 days from close of auction unless prior agreement is made. Please ask any questions in advance:RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28e013%3F%3E%3A-14129811233-0xfa-
|
|
|
Bridgeport CNC Mill 760/20 Runs Perfect Very Clean
Bridgeport CNC Mill Heidenhain TNC 145 control. Works perfect out of clean shop and very well maintained Table size. 39x19 Table travels 30"x20"x20" Rapids X and Y 1259"min Z 787"min Tool holders BT40 16 ATC Weight 8000# Will load for free buyer pays all shipping Call Sean 818-355-2974 Posted with
|
|
|
Bridgeport EZTRAK 3 axis cnc mill
This is a re-listing. This machine didnt go the first time around. Maybe the variable speed head being a bit noisy scared some off. My repair guy said it's roughly a $400 fix. bushings and labor) Look anywhere for one of these and the prices are ridiculous. This is priced for the buyer to get a good deal and for us to clear out the shop for a bigger machine. Bridgeport EZTRAK 3 axis CNC mill-R8 Spindle Lightly used. Holds finishes and tolerances expected of a knee mill Newly replaced spindle bearings Newest software upgrade New controller batteries This machine runs great. Liquidating to allow for larger machine. We already have small CNC milling capabilities. So our loss is your gain! Machine is currently running and has just(1 month ago) gone through a thorough check and maintenance routine. Variable speed unit is a bit noisy but doesn't ... moreeffect operation. Machine can be loaded on riggers truck. PLEASE CHECK WITH RIGGERS FOR SHIPPING AND HANDLING CHARGES*
|
|
|
Bridgeport Series 1 Interact MK2 CNC Mill Milling Machine, Heidenhain Controller
Bridgeport Series 1 Interact MK2 CNC Mill General Info: Stock# MD-913-824 Condition: Used. Excellent Tested: Yes. Good Working Condition Brand: Bridgeport Model: Interact MK2 Serial: 665701190 D Year: 1991 Weight: N/A Shipping Dimensions: N/A Location: Stone Mountain. GA Specifications: CNC Control.Heidenhain TNC 2500 Table Size.42" x 16.1" Working Surface.34" x 12.5" Longitudinal Travel(X Axis)18" Cross Travel(Y Axis)12" Vertical Travel(Z Manual)14.3" Power Feed.0.1- 197 IPM Manual Feedrate.0.4- 29.5 IPM Rapid Traverse.197 IPM Number of T-Slots.3 Width of T-Slots.0.625" Centres of T-Slots.4.375" Speed Range(Infinitely Variable)40- 4000 RPM Quill Travel.4.9" Motor: 6HP/ 208V/ 3 Ph Additional Info: Machine has been well taken care of and is in great working condition. Package comes with several ... morepieces of tooling. Vice, several manuals along with original paperwork. Machine can be shown under power. Seller Contact Information: Mark Davis 404-272-1285 The Equipment Hub. LLC 1380-A Beverage Drive Stone Mountain. GA 30083 It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week. Visit Us on the Web at
|
|
|
Bridgeport EZ Trak SX CNC Vertical Mill
Bridgeport EZ Trak SX CNC Vertical Mill· Serial Number BR 261227 E· 9” X 48” Table Size· Table Travel(X) 30” Saddle Travel(Y) 12” Vertical Knee Travel 15” Quill Travel(Z) 5” Spindle Speed 60-4200 RPM· 2HP Motor· EZ Trak 2 Axis CNC Control· Z Axis Readout· New LCD Screen· New Keyboard· Coolant System· Central Lube System· 220V Connectors and cables have been repaired or replaced as needed. The machine has recently been refurbished and is fully functional. The machine was used in a manufacturing facility and has since been removed from service. It is being sold AS-IS. This item must be shipped by freight so rates will vary and shipping an item of this size can be costly. Please only bid if you are prepared to pay for shipping. Please contact me for shipping estimates. We have a shipping ... moredock and a forklift for freight items. Local pickup is acceptable. We do not allow third party shipping. We will however by happy to work with your preferred carrier. Please feel free to contact me with questions Thank You, Josh Combs jcombs@mcelroy.com*Notice: In accordance with state tax regulations. Products sold may be subject to sales tax. The following states will be subject to sales tax: Alabama, Arkansas, Georgia, Illinois, Indiana, Kansas, Massachusetts, Maryland, Minnesota, Missouri, New Jersey, Oklahoma, Pennsylvania, South Dakota, Texas, Washington, and Wisconsin. If you are exempt from sales tax, please provide sale tax exemption certificate prior to completing payment.
|
|
|
BRIDGEPORT CNC VERTICAL MILL EA5MH IPA ISO 5599/1 VALVE RELAY BOX
BRIDGEPORT CNC VERTICAL MILL EA5MH IPA ISO 5599/1 VALVE RELAY BOX Description: BRIDGEPORT CNC VERTICAL MILL THIS METAL BOX HAS A ITA EA5MH ISO 5599/1 VALVE WITH 2 RELAYS BOX MEASURES 6 X 5 1/2 X 5 WITH A BRACKET FOR MOUNTING I PUT USED BUT I THINK ITS BRAND NEW Shipping: Payment: Click to Enlarge Click to Enlarge Click to Enlarge Click to Enlarge Click to Enlarge inkfrog terapeak.
|
|
|
EAGLE 500 BRIDGEPORT HAAS ANILAM 1400 CNC 3 AXIS VMC POWER DRAWBAR KNEE MILL
THIS AUCTION IS FOR A USED EAGLE 500 VERTICAL KNEE MACHINING CENTER WITH ANILAM SERIES 1400 CONTROLS. $$$$ PLEASE EMAIL OR CALL 1-812-968-5230 IF YOU HAVE ANY QUESTIONS. $$$$ YOU CAN SEE IT UNDER POWER IN MY WAREHOUSE IN LOUISVILLE.KY. MILL IS IN GOOD USED WORKING CONDITION. CHECK OUT YOU TUBE VIDEO'S http:youtu.be/WzN3LPolYNY SPECIFICATIONS: TABLE: 16" x 51" X-AXIS TRAVEL: 33" Y-AXIS TRAVEL: 16" Z-AXIS TRAVEL: 6" POWER KNEE TRAVEL: 16" SPINDLE: 40(STANDARD) SPINDLE SPEEDS(VARIABLE) LOW- HIGH RANGE: 80- 3800 RPM MOTOR: 5 HP/ 3 PH/ 220/440 V EQUIPMENT INCLUDED: ANILAM SERIES 1400 3-AXIS CNC CONTROL COOLANT SYSTEM. TOOL CHANGER. MACHINE WEIGHT APROX. 6500LBS. PLEASE GIVE US A CALL AT 1-812-968-5230. FOR SHIPPING QUOTE PLEASE SEND A COMPLETE ADDRESS! IF ITEM IS BEING SHIPPED TO A BUSINESS OR RESIDENTIAL? WITH ... moreDOCK OR FORKLIFT? OR IF YOU WANT TO PICK UP AT FREIGHT TERMINAL. I WILL LOAD FOR FREE ON YOUR TRUCK OR TRAILER. PLEASE EMAIL OR CALL 1-812-968-5230 IF YOU HAVE ANY QUESTIONS. YOU BUY AS IS. BUYER PAYS SHIPPING. PLEASE CHECK OUT MY OTHER AUCTIONS. PLEASE EMAIL IF YOU HAVE ANY QUESTIONS. Powered by The free listing tool. List your items fast and easy and manage your active items.
|
|
|
Cleveland NOS Ball Nose 1/8 End Mill 2FL for Machinist Gunsmith CNC Bridgeport
One used Cleveland HSS Ball Nose End Mill. 1/8" dia of cut, 3/8" shank, 2 3/8" OAL, Center Cut. Item in the picture is the one you will receive. I do combine shipping. But please let me know if you are bidding on multiple items, and if you win multiple items wait till I send an invoice to reflect correct shipping. I accept PayPal only. I do not ship outside the USA. Thanks for looking. Normal 0 false false false EN-US X-NONE X-NONE
|
|
|
Universal KWIK SWITCH TOOL HOLDER 200 CNC BRIDGEPORT MILL
WE COMBIDE SHIPPING COMES WITH 6 COLLETS 1/4 TO 5/8 RANGE
|
|
|
Bridgeport Series 2 BMC 7845 CNC Mill
Bridgeport Series 2 BMC 7845 CNC Mill Description: For auction is a Bridgeport Series 2(BMC7845) CNC Mill. This machine has had very little actual use since it was new because it was used mostly for prototype work. And not for job shop work and not for the reoccuring manufacture of any product. I would rate all surfaces, including the work table itself, as being at least 95% as compared to brand new equipment. All the mechanical features should be in excellent condition, and far better than any similarly aged machine on the market. It has been stored for the last fifteen or more years, and hasn't been powered or run a single part in that length of time. The controller is an Allen Bradley 8200 and it worked just like new before storage. The machine includes only the mill related items shown in the pictures, plus one magnetic tape on a ... morereel which I'm told is the exec file that is like the operating system on a desk top computer, and a stack of manuals. The Included Manuals are as Follows: An Allen Bradley 8200 Programming Manual. Two different editions(about 70& 150 pages) and two different operating/operators manuals for the 8200 control(about 70 pages each) plus one operators reference guide(49 page booklet) There is one maintenance manual(about 150 pages) and one parts manual(about 200 pages) and both of these last two books include information about the controls and the mechanicals. There is a thick three ring binder with lots of manuals in it for the drives and other electrical details and for the hydraulic subassemblies and switching such as; Power Draulics-Nielsen Inc(hydraulics sub system) Volkmann Electronic Drives(maybe 30 pages) Motorolla CRT(about 25 pages) and a service manual from the Ball Electronic Display Division(about 40 pages) GE Intersil Sys for CMOS memory module for multibus(booklet) LS703 Sealed incremental linear transducer(22 pages) Kollmorgen Corp Ind Drives Div- PWM Switching Amp(about 64 pages) and four more Allen Bradley books titled"Pal user manual" about 300
|
|
|
Bridgeport Machine 12x10x6" Tri-sine Plate Milling Rotating CNC Suburban Mill
If you are looking at this. Then you know what a killer deal this is! Please DO NOT kick yourself by missing this one! I am not a machinist but if you ask me questions. I will try to answer as best I can. Let my lack of knowledge. Be your deal! I obtained this from an industrial arts center that was cleaning out. This bad boy is HEAVY. It weighs 100 pounds without crating. Checkout my other auctions—who knows maybe you’ll make out like a bandit! Here's my"nobody gets burned" return policy: You'll be happy with it. I'm certain. In fact, if you're not happy with it for some godforsaken unforeseen reason(and I can't imagine what that might be) I'll take it back and refund your bid amount, less my listing and value fees, provided it doesn't look like you drove a truck over it, and provided you pay the postage ... moreto return it to me within 10 days from the date I mailed the package. PayPal for immediate shipping. anywhere at a lower-48 U.S. address for $125.00 by FedEx Ground.
|
|
|
KURT D-80 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE
KURT D-80 8 INCH MACHINE VISE FOR CNC BRIDGEPORT MILL MILLING MACHINE KURT D-80 8 INCH MACHINE VISE FOR BRIDGEPORT MILL MILLING MACHINE. THIS UNIT IS IN GREAT SHAPE. NO HANDLE. All purchases are expected to be payed within 5 business days. Items will be shipped UPS or Fedex Ground. We do not ship to P.O. Box. Buyer will have to pay"duty" if shipped internationally Insurance can be purchased at an extra cost. PLEASE BE ADVISED THAT ALL ITEMS ARE SOLD IN USED CONDITION UNLESS SPECIFIED AS BRAND NEW. ALL ITEMS ARE SOLD AS IS WITH NO WARRANTY. YOU ARE BUYING USED EQUIPMENT AT USED PRICES. WE DO OUR VERY BEST TO DESCRIBE EACH ITEM AND ITS CONDITION. ALL ITEMS ARE SOLD IN GOOD TO GREAT WORKING CONDITION. IF YOU ARE NOT HAPPY WITH YOUR PURCHASE PLEASE CONTACT US BEFORE LEAVING A NEGATIVE FEEDBACK. OUR PHONE NUMBER IS 1 718 698 8400 WE ... moreARE LOCATED AT 3521 VICTORY BLVD STATEN ISLAND NY 10314. WE ARE OPEN 8AM TO 6PM MON-SAT. YOU CAN CALL US AT 718 698 8400
|
|
|
Bridgeport Series II Special Easy Trak DXII 2 Axis CNC Vertical Mill 11" x 58"
Bridgeport EZ Trak DXII 2 Axis CNC Vertical Mill EZ Trak DX CNC Control 14.5″ x 9″ Flat screen Monitor Quick Draw Speed Tool Changer Power Feed X Box chrome ways Remote start switch BIJUR automatic lubrication system Coolant Tray Electrics: 2 HP/ 220/3/6 New: 1993. 11″ x 58″ Bed 2Hp. Variable Speed Head. 2J Drive Table Travel(x axis) 32″ Saddle Travel(y axis) 14.5″ Spindle Travel(z axis) 5″ Please feel free to inspect this machine at any time! Please call 203-592-8402 with any questions.
|
|
|
CNC MILLING MACHINE BRIDGEPORT TYPE CENTROID CONTROL RETROFIT 2006 CNC KNEE MILL
CNC MILLING MACHINE NASA II BRIDGEPORT TYPE KNEE MILLING MACHINE. CENTROID RETROFIT IN 2006 PC BASED CONVERSATIONAL SOFTWARE VERY SIMPLE AND EASY TO PROGRAM. 3 AXIS. MEHENITE CASTINGS, HAS RIDGED OVERARM, COOLANT, AUTO LUBE, ALLIGN POWER DRAWBAR, 3 HP HEAD, 30 TAPER, PC TOWER LOCATED IN ELECTRICAL PANEL FOR CLEAN OPERATION, CUSTOM BACK SPLASH, COMES WITH FULL SET PLUS SOME EXTRA OF 30 TAPER TOOL HOLDERS, ALSO COMES WITH A 6" KURT ANGLE LOCK TYPE IMPORT VISE, TABLE NEVER BEEN DRILLED OR MILLED, WAYS LOOK GOOD, CONTROL PANEL HAS 10 FOOT CORD COMES WITH CART FOR TOOLS, MONITOR, KEY BOARD AND CONTROL PANEL. APPROX. 500 HOURS SINCE RETROFIT. TRAVEL IS X-28" Y-13" Z-5" WE BOUGHT A MILLING CENTER SHORTLY AFTER THE RETROFIT AND HAVE NOT USED IT MUCH SINCE AND NEED THE ROOM SO IT NEEDS TO GO. VERY NICE CNC MILL. BUYER RESPONSIBLE ... moreFOR ALL SHIPPING AND ARRANGEMENTS WE CAN LOAD IT ON YOUR TRUCK OR FLAT BED SEMI TRAILER. THE MILL IS FOR SALE LOCALY SO WE RESERVE THE RIGHT TO END THE AUCTION AT ANY TIME. PLEASE TAKE A LOOK AT OUR EBAY STORE WE HAVE OTHER MACHINES AND TOOLS FOR SALE ANY QUESTIONS PLEASE EMAIL OR CALL 828-632-1500 IF NO ONE ANSWERS PLEASE LEAVE A MESSAGE WE WILL GET BACK ASAP THANKS VERY MUCH FOR LOOKING TODD AND SHANNON
|
|
|
Bridgeport Series I 2 Axis CNC Vertical Mill w/ Prototrak MX2
Offering one(1) used Bridgeport Series I CNC 2 axis vertical mill. The control is a Southwestern Industries Prototrak MX2. The machine has a 4" riser and a power draw bar. I can load the machine onto your truck at no additional charge. You may view the mill under power in Warren. MI(suburb of Detroit) The machine is fully functional but is sold"as is" If you have any questions feel free to call Ted at 586-754-9200.
|
|
|
ALIGN AL-99SP POWER FEED for mill X Axis Milling Machine Cnc Bridgeport
Align AL-99SP power feed. Good shape tie rap on cap but been there years without moving Posted with
|
|
|
BRIDGEPORT CNC MILL M3 CONTROL
YOU ARE BIDDING ON A 2 H.P. VARIABLE SPEED HEAD BRIDGEPORT MILL WITH A M3 PROTO TRAK CONTROL SYSTEM. THE CONTROL BOX IS NEW, THE Y AXIS MOTOR IS NEW, THE HEAD IS REBUILT, THE MACHINE IS IN EXCELLANT CONDITION, HAS AN ELECTRIC LUBE PUMP, THE TABLE IS A 9 X 48 FOR PLENTY OF TRAVEL, THE SPINDLE IS R8, A NEW POWER DRAW BAR WILL BE INSTALLED TO THE NEW OWNER, LOADING IS FREE OF CHARGE ONTO A FLAT BED TRAILER OR TRUCK AT GROUND LEVEL, ANY QUESTIONS PLEASE CALL JACK AT 937-572-3998, BUY IT NOW AT 16,700.00.
|
|
|
BRIDGEPORT EZ-TRAK 2-AXIS CNC MILL - 9"x48" 2HP MILLING MACHINE 3-Axis DRO
ebay template EZ-Trak 48" x 9" Series 1 CNC Milling Machine I TEM S OLD A S P ICTURED This is the EZ TRAK CNC Milling Machine. Combine the Series I or II Special with an easy-to-use control. And you have the EZ TRAK CNC. With the EZ TRAK, operators can alternate between manual and automatic milling as their application demands. Its two-axis control has a fully adjustable, flat screen Monitor that prompts for all machining data and signals the operator when an action is required. The control stores up to 2.000 individual operations. This Bridgeport Series I model features a powerful 2 HP spindle motor, large table travel, and automatic cutter compensation so you can use those reground milling cutters. Chrome-plated ways and a centralized, one shot lubrication system ensure a long machine life. FEATURES 2-Axis CNC Control 3-Axis Digital ... moreRead-out 2HP Spindle Motor Chrome ways One shot lubrication SPECIFICATIONS Table Size 48" x 9" 1219 x 229mm Table Travel(manual feed) 36" 914mm Table Travel with power feed 27½" 699mm Saddle Travel 12" 305mm Quill Travel 5" 127mm Knee Travel 16" 406mm Ram Travel 12" 305mm Throat Distance 6¾" ~ 18¾" 171 ~ 476mm Spindle to Table 2½" ~ 18½" 64 ~ 470mm Spindle Motor 2HP Spindle Speed Range 60 ~ 4200 rpm Spindle Taper#30 QC Feed Rate ¾ to 35 ipm 19 to 889mm/min Floor Area 7 x 10ft 2.1 x 3.1m Height 82" 2083mm Net Weight 1988 lbs. 900 kg. Power 208/230 Volt 60 Hz. 3 Phase*Specifications subject to verification INSPECTION NOTES: As with any piece of equipment. New or used, this item will require additional inspection after it arrives due to the vibration during transit. We recommend you hire a professional service person to install the machine, test it and perform any necessary service adjustments before putting it in to production. Please refer to the pictures for this item's cosmetic condition. This item is sold as pictured. Shipping Shipping is the responsibility of the buyer; ho
|
|
|
BRIDGEPORT Series II CNC MILL -SERIES 1 MILLING MACHINE Military
This mill was in working condition when it was placed in storage i do not know much about these but will do my best to anwser any questions you might have i will get you measurements or numbers but please ask in detail what you need me to get. We can store thus if you can not pick up right away or load on semi for you. If you send a semi company there will be a 100 packaging charge Posted with
|
|
|
BRIDGEPORT EZ TRAK DXII 3-Axis CNC Vertical Mill Milling Machine
BRIDGEPORT EZ TRAK DXII 3-Axis CNC Vertical Milling Machine. S/N 8554E, New 1997. Stock# 30793 Specifications: Table Size- 11" x 58" Table Longitudinal Travel(X-Axis) 32" Saddle Cross Travel(Y-Axis) 14.5" Quill Travel(Z-Axis) 4.4" Knee Vertical Adjustment- 11" Ram Travel In/Our- 17" Throat Distance. Min to Max- 5" to 17" Table Max Height Above Floor- 47" Max Uniform Table Load- 600 Lbs. Spindle AC Motor Rating- 2 HP Cont/ 3 HP 30 Min Spindle Taper- R8 Spindle Speeds- 60 to 4200 RPM Ballscrew Diameter- 1.25" Feedrate Range- 0.1 to 100 IPM Floor Area- 9' x 7'9" Height- 6.9" Net Weight. Approx- 3900 Lbs. Shipping Weight. Approx- 4700 Lbs. Equipped with: EZ Trak 3-Axis CNC Control Conversational Programming Remote Start Stop Hard Chrome Plated Box Ways Air Assist to Knee ... moreBijur Automatic Lubrication Coolant System Plexiglass Table Enclosure. Work Lamp 3.5" Floppy RS232 Port DC Servo Motors DX32 Programming and Operations Manual PRICE: $22.500.00 USD FOB TRUCK DAYTON OH" Offered locall y an d subject to prior sale. Also su bject to the standard MD NA 30 day ret urn pr ivilege. Freight prepaid. If proven mechanically unsat isfactory or repair at seller option. Loading is availab le. Buyer resp onsible for shipping. We can assist with shipping rate quotes on request. Local sales tax is 7.25% if appl icable. Wire transfer. Ca shier's check. Paypal, company check. Mc and visa are all acceptable forms of payment. Cre dit card users need to cal l us with the card information. Sale subject to Advanced Machinery Companies Terms& Conditions.
|
|
|
Bridgeport Series I 3-Axis CNC Mill w/ BPC2M Control 9"x48" Table & Chrome Ways
BRIDGEPORT EZ TRAK 3-AXIS CNC MILLING MACHINE W/ BPC2M CONTROL Description: Up for sale is a Bridgeport EZ Trak CNC Mill. This mill is in great running and operating condition. It features a chrome ways. A 9” x 48” table, 3-Axis CNC controls, and 30”X) x 12”Y) x 16”Z) travels. It is powered by Brideport’s BPC2M programmable control. SPECIFICATIONS MANUFACTURER BRIDGEPORT SERIES I SERIAL BR 2776295 TRAVEL(X) 30” TRAVEL(Y) 12” TRAVEL(Z) 16” CONTROL BPC2M APPROX WEIGHT 2900LBS FOR MORE INFORMATION PLEASE CALL GARY AT(510) 453-0513 FOR MORE INFORMATION PLEASE CALL GARY ARAGON AT 510 453-0513 LOCATED AT 601 ALADDIN AVENUE. SAN LEANDRO. CALIFORNIA 94577* TERMS AND CONDITIONS* SALES Your bid is a contract. Place a bid only if you are serious about buying the item. If you are the winning bidder. You will enter into a legally binding contract to purchase ... morethe item. If the seller is unable to establish contact with the winning bidder within three days of the end of the auction, or if payment isn’t received within three days of the invoice date, item may be offered to the next highest bidder or re-listed at the sellers’ discretion. Please do NOT pay until you are invoiced! PAYMENT TERMS Gary S. Aragon. LLC accepts ATM and these major credit cards: Visa, MasterCard, Discover. Buyers may call us at 510 453-0513 with credit card information. You can also use PayPal. PayPal payments should be sent to garysaragon(at) comcast.net. CALIFORNIA STATE SALES TAX APPLIES TO ALL STATE RESIDENTS… unless we receive a valid resale card. EBAY TERMS eBay charges Gary S. Aragon. LLC a service charge for each item we list. If a customer cannot or does not pay for an eBay purchase in the specified amount of time, Gary S. Aragon, LLC will file a non-paying bidder alert with eBay. Gary S. Aragon LLC will hold the non-paying bidder responsible for the eBay fees and commissions occurred by us. SHIPPING Buyer is responsible for all shipping costs and arranging shipping for bigger/heavier items. Most of our items are
|
|
|
Series I BRIDGEPORT Interact Three-Axis CNC Vertical Mill (New 1987)
Preowned BRIDGEPORT Three-Axis CNC Vertical Milling Machine. Model: Interact I, S/N 24850187C(New 1987) Overall size of table Table working surface Number of t-slots Range: longitudinal(X) cross(Y) vertical. Knee(manual) quill(Z) Throat distance Distance. Table to spindle- up at gage line Maximum uniform table load Infinitely variable spindle speeds Spindle taper Feed rate. All axes Feed increments Rapid traverse rate. All axes 16-1/8" x 41-1/2" 12-1/2" x 34" 3 18" 12" 14-3/8" 4-59/64" 15-9/16" 2" 300 Lbs. 50-3.750 R.P.M. 30 Quick Change 0.4-30 I.P.M. 0.1 I.P.M. 200 I.P.M. Equipped With#TNC 151A HEIDENHAIN three-axis contouring CNC control with RS-232C port Three-axis linear and two-axis circular interpolation Ball screws and DC servo motors for all axes Electronic handwheel for manual operation ... morein all three axes Selector levers for directional feed and rapid traverse in all three axes Manually controlled or programmable spindle speeds Chrome ways(14) 30 Quick Change tool holders with(13) assorted size collets Work light Leveling pads SIEBE lubrication system Flood coolant system with pump motor and oil pan 2 H.P. 3/60/220-440 volt spindle drive motor Machine is wired for 3/60/208 volt operation. Approximate Weight: 2.460 Lbs. Approximate Dimensions: 64" L-R x 60" F-B x 90" H, We Ship Worldwide- F.O.B. Truck. Hauppauge- Long Island, NY) di,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishhov%3C%3Edi-146b8b9daf3-0x10b-
|
|
|
BRIDGEPORT SERIES 1 CNC MILL *GREAT RETROFIT CANDIDATE*
THIS AUCTION IS FOR A USED BRIDGEPORT SERIES 1 CNC VERTICAL MILLING MACHINE. MACHINE IS GOOD CONDITION! THIS MACHINE CAME OUT OF A SCHOOL! THIS WOULD BE A GOOD CANDIDATE FOR A RETROFIT! YOU CAN SEE MACHINE UNDER POWER IN MY WAREHOUSE. $$$PLEASE EMAIL OR CALL 1-812-968-5230 IF YOU HAVE ANY QUESTIONS OR SHIPPING QUOTE$$$ MODEL: BRIDGEPORT SERIES 1 S/N: CNC 2667 2HP. COMES WITH SEVERAL TOOL HOLDERS. PLEASE EMAIL OR CALL 1-812-968-5230 IF YOU HAVE ANY QUESTIONS. YOU BUY AS IS. BUYER PAYS SHIPPING. PLEASE CHECK OUT MY OTHER AUCTIONS. PLEASE EMAIL IF YOU HAVE ANY QUESTIONS. Powered by The free listing tool. List your items fast and easy and manage your active items. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-146c760398b-0x10d-
|
|
|
bridgeport cnc vertical mill 9X42 table
this came out of a school has very low time the ways are very good 2 axis machine if any question call me at 207-314-7565 mike for delivery is 1.75 per mile
|
|
|
EXCELLENT LOW HOUR 2001 LAGUN CNC MILLING MACHINE ANILAM 3300MK bridgeport Mill
Please watch video below. This sale is for a very nice. Low hour 2001 one owner Lagun FTV-1 3-axis CNC milling machine with Anilam 3300MK control system. This machine came out of a college lab so it has only seen light use for R&D and prototype work. Machine has lots of nice features such as: Quick switch NMTB40 spindle with toolholders as shown. Programmable M codes for spindle and coolant. Automatic lubrication system. Easy to use Anilam 3300MK control with training video*Full Cnc or manual operating modes. Heavy-duty Meehanite cast iron construction. A comparable machine as equipped from Republic Lagun today will cost you over $40.000 new. You're more than welcome to inspect this machine under power. Free loading! If you have any questions or would like to make an offer please feel free to call or text 573-578-9890. Specifications: ... more230V/3PH/60HZ Year of mfg: 2001 Table size: 10" x 44" Table t-slots: 3" x 5/8" Longitudinal table travel:24" Cross table travel: 14" Vertical knee travel: 16" Quill travel: 5" Ram travel: 22-3/16" Spindle speeds: 55- 4250 RPM. Variable(2-ranges) Spindle taper: 40 NMTB quick switch. Maximum table weight load capacity: 750 lbs Spindle motor: 3 HP Head tilt. Front to back: 45 degrees Head tilt. Side to side: 90 degrees Quill diameter: 3-3/8" Estimated machine weight: 2850 lbs Overall dimensions: 64"w) x 73"d) x 85"h) Please watch video below: Posted with
|
|
|
Supermax Accurite Millpower 3 Axis cnc knee mill Bridgeport Style Manual Mill
Supermax accurite millpower 3 axis cnc knee mill. Accurite millpower 3 axis add on new is over 18.000 new by itself. Motor is 3 phase but has 3phase power inverter so it runs off 30 amp 220v just fine. This also allows for spindle speed adjustment by dial on inverter. Everything in good working condition. Comes with 6 inch te-co vise and set of r8 mill holders and collets. Drill index, 4" 1-2-3 blocks. Parallel set and parallel separator. Clamp set. Some new carbide mills around 200-300 dollars worth. Bag of various taps metric and standard new and used. Machine works great and is very easy to program. Great for second operations. Comes with book for the millpower control. Freight shipping is an option email me with any questions before doing any offers or sale. Local pickup is also available. 1000 dollar non refundable deposit do at ... moreend of auction. Posted with eBay Mobile
|
|
|
(1) Used Bridgeport Series I-2HP Ez-Trak DX, CNC Vertical Mill, New 1997
1) Used Bridgeport Series I-2HP Ez-Trak DX. CNC Vertical Mill, New 1997 Specifications: Table Size: 9" X 48" Travels: X' Axis 30" Y' Axis: 12" Z' Quill: 5" Knee Vertical: 15" Spindle Speeds: 60 To 4.200 RPM Spindle Motor: 2- 3 HP Spindle Taper: R-8 Equipped With: Bridgeport EZ Trak DX Control Kurt Power Drawbar Chrome Ways Bijur Lube System High Intensity Work Light Mist Coolant System Tool Pedestal Collets Voltage: 480/3/60 Specifications and Equipment Are Preliminary. Subject to Buyer Verification. Please contact us for shipping options. Our Inventory# Tfori 12181 Information is Preliminary. Subject to Buyer Verification. If you would like to inspect this item please contact us to make arrangements. We are a member of the MDNA(Machinery Dealers National Association) Orca Machine Tools. Inc. is a ... morestocking used machine tools dealer in Albertville, MN. Please contact us with any questions you may have. There is a $20 loading charge on freight shipments. Buyer is responsible for all shipping costs. US Buyers: Insurance is provided at the buyers request and at the buyers cost. International Buyers are required to pay for Insurance. Please contact us for a shipping quote. Also please wait for an Invoice from us prior to sending payment. If you wish to purchase multiple items. We combine items for shipping and send you an invoice for all items with the combined shipping price. Minnesota buyers will be charged sales tax. Payment in full must be made within 2 days of bid closing. We accept PayPal. Funds must clear prior to item shipment. Visit our eBay Store! Powered by The free listing tool. List your items fast and easy and manage your active items.
|
|
|
Bridgeport Series I knee mill, ProtoTRAK AGE III 3-axis CNC
Please call Joe@ 203-592-8402 or email jag67@optonline.net Bridgeport Series I knee mill. ProtoTRAK AGE III 3-axis CNC control. Mill Refurbished 7/2014 by Machine Builders of New England Refurbished 2014. Bridgeport Series I knee mill, ProtoTRAK AGE III 3 axis CNC control. Specifications: Table 9 x 42" Travels(X) 30" Saddle Travel( Y) 12" Quill Travel(Z) 5" Knee Travel( Z) 16" 2 HP Variable Speed Head. R-8 Taper Spindle. Ultron Power draw bar, RPM 60-4200, Chromed ways. New Bijur 1 shot lube system. New Belts. Pulleys, and Clutches for 2HP J-Head. New bearings. Epoxy painted to original Bridgeport gray. Completely refurbished. 1 year parts warranty.
|
|
|
Bridgeport R2C3 Series 1 CNC Mill Project with Most Everything You need
This is a nearly complete Bridgeport Series 1 R2C3 CNC project ready to take a new PC Based Controller IF YOU PURCHASE THIS YOU WILL NEED TO RIG IT OUT YOURSELF. I DON'T HAVE A FORKLIFT, A SMALL FORKLIFT WILL GO RIGHT IN, ALSO WANT IT REMOVED BY END OF SUNDAY 8/14, PLEASE DON'T BID IF YOU CAN NOT DO THIS Now for all the good stuff you will get: A 1984 R2C3 Bridgeport Series 1 CNC with Ball Screws that's stripped and ready to go. 2 HP 3Phase Motor Power Draw Bar Quick Change tooling CNC Vise as shown Automatic Oiler Scraping still shows on the ways We used it with the old Heidenhain controller up until 7/13 when we lost the Y axis motor and started the conversion. The iron is in good shape for age. A complete 1200 oz 3 axis stepper conversion kit from LONGS motor(Search for it the $450.00 kit) That's the three motors, power ... moresupplies, breakout board, etc. The X and Y couplings have been machined by us. You just need to make the z coupling and the mounting plates for the three axis. Or toss our stuff and make your own. A Dell 15 inch touch screen monitor PC Power Supply. Video card, motherboard and Sempron 4 core processor all new as in picture(You add hard drive and memory) You basically have to clean it. Fabricate some couplers and some attachment plates, buy wiring, do wiring and assemble it. Priced to sell. Feel free to ask questions. I'll do my best to answer. No returns on this. Will only take PayPal for payment. Sorry. Have had bad experiences otherwise. If you need another picture just ask. It's covered with dust from our shop. Been a bit since I worked on it.
|
|
|
Bridgeport V2XT Cnc Mill,Missing computer
You are bidding on a USED Bridgeport V2XT Cnc Mill.Missing computer,the unit is not tested is missing the computer and hard drive,comes with the drives and motors installed,NO screen.Sold AS IS for part or repair. Buyer will need to arrange the flat bed or pick up with a trailer.I can load for free. Payment should be made no later than 5 days after the auction ends. It will be $150.00 for a palletizing fee with straps and just shrink wrap or $400.00 for a crate. Texas Residents Pay 8.25% sales Tax Local Pick ups are welcome with Cash on hand only. All items must be shipped. Picked up, or removed within 7 days of the end of auction"unless pre-approved via ebay message system" Items left after this time will be subject to a $20 per day storage fee. The buyer will forfeit the item- and any payments made- when storage fees reach either ... morethe sale price of the item or a time period of 30 days from the sale of the item. Whichever comes first. No money will be returned for forfeited items. Without notice, items are subject to relisting immediately upon forfeiture. For items that have incurred storage fees, electronic payment of the fees due will be required for the item to be shipped or released for pickup. If you have reason for a delayed pickup please let me know.
|
|
|
Chevalier 2 Axis CNC Vertical MIll with Prototrak Controller - Bridgeport Style
CHEVALIER FALCON FM-3VKH VERTICAL MILL 2-AXIS CNC Proto Trak Controller Year New- 1996(Estimated) SPECIFICATIONS: Table Dimensions(Overall. W x L) 10" x 50" Longitudinal Table Travel Power Feed(X-Axis) 30-3/4" Cross Saddle Travel(Y-Axis) 15-3/8" Vertical Knee Travel(W-Axis) 15" Vertical Quill Travel(Z-Axis) 5" Ram Travel. 18" Spindle Taper. 30 Taper Spindle Speeds. 80-4300 RPM Motor(Spindle) 3 HP Electrics. 220/440/3/60 EQUIPPED WITH: Proto Trak 2-Axis CNC Control. Digital Readout for the Quill Power Quill Feed Variable Speed Spindle Swivel Type Overarm One Shot Lube System Approximate Machine Dimensions. 72" x 60" Approximate Machine Height. 84" Approximate Machine Weight. 3500 lbs. Specifications subject to buyer verification. Please call us today, Equipment-Specialists or Big Dog Machinery ... moreMachine can be inspected under power in Warren MI. Price is loaded FOB our warehouse. key works Bridgeport. Acer, Alliant, chevalier,
|
|
|
Bridgeport Style Knee Mill CNC 2 Axis Vertical Mill with Proto Trak Controller
This is a 2006 Mill Pro knee mill. Very similar to Bridgeport knee mill. The Proto-Trak computer was replaced in 2013. This machine runs very well and is still under power for your test and demo needs. This machine is sur-plus and is not needed any longer. Will accept cash on pick-up. Or cleared check/money order ONLY. Please contact 586-215-9903 between 9 a.m. and 6 p.m. EST for any questions or concerns or send me an ebay message.
|
|
|
milltronics cnc mill 3 axis bed mill Santec RB-10 bridgeport type
Santec cnc 3 axis bed mill with a Milltronics Centurion 1 control. Similar to a bridgeport mill Can use as a manual machine or cnc. Conversional and G-code programing. Mist and flood coolant. Head runs and sounds very good. Holds great tolerance. Takes R-8 collets. 220 3phase motor. Vice not included. Under power and can see run. Call/ text with any questions or to see run 815 575 4475 Pick up only. I do not have a Forklift to load. All shipping is Buyers Responsibility
|
|
|
2008 BRIDGEPORT/HARDINGE E-Z VISION 3 AXIS CNC TEACH-TYPE VERTICAL MILL
Thousands of Used Metalworking and Plastic Machines& New Machine Tools Photos, Full Descriptions and Prices- Fast& Easy About Us Shipping Payments& Checkout FAQs Our Inventory Home CNC Machines Manual Lathes. Mills, Drills, Saws Grinders. Hones, Finishing Fabricating Equipment Presses& Feeds Boring Mills Automatic Screw Machines EDMs Inspection Equipment Air Compressors Plastic Machinery Planers& Planer Mills Broaches& Keyseaters Shapers& Slotters Tooling& Accessories Welding Equipment Wire& Fastener Ovens. Furnaces& Environmental Misc Metalworking Gear Machinery Material Handling Misc Non-Metalworking 2008 BRIDGEPORT/HARDINGE E-Z VISION 3 AXIS CNC TEACH-TYPE VERTICAL MILL Ref# 153195 iammdna XMVCNC BRIDGEPORT/HARDINGE CNC VERTICAL MILL MODEL:SERIES I WITH E-Z VISION CNC CONTROL 3-AXIS CNC PLUS MANUAL ... moreHANDWHEELS S/N: HDNG-3964D. NEW: 2008 SPECIFICATIONS: TABLE SIZE. 9" x 48" TABLE TRAVEL(X-AXIS) 30" SADDLE TRAVEL(Y-AXIS) 12" QUILL TRAVEL(Z-AXIS) 5" KNEE TRAVEL. 16" RAM TRAVEL. 12" MAXIMUM LOAD DISTRIBUTED. 300 LBS. SPINDLE TAPER. R-8 SPINDLE SPEED RANGE. 60-4200 RPM. SPINDLE DIAMETER. 1-7/8" QUILL DIAMETER. 3-3/8" FLOOR AREA(DOORS CLOSED) 8'2" x 7'3" HEIGHT. 6'8" WEIGHT(WITH CONTROL) 2.900 LBS. EQUIPPED WITH: BRIDGEPORT EZ-VISION CONTROL(3-AXIS) PC BASED. HD 1.44 MB, 8MB PC FLASHDISK,POWERFUL CANNED CYCLES. USER DEFINABLE MACROS. ETHERNET PORT, USB. 10.5 COLOR LCD SCREEN. IN MANUAL MODE THREE AXIS DIGITAL READOUT. X. Y& Z BALLSCREWS AND SERVO MOTORS. CHROME WAYS. TORQUE-RITE AIR ACTUATED POWER DRAW BAR. BIJUR AUTO-LUBRICATION SYSTEM. SPRAY MIST COOLANT SYSTEM. POWER DRAW BAR. BRIDGEPORT SERIES I HEAD 2/3 HORSE POWER SPINDLE MOTOR VIDEO: INSPECT UNDER POWER IN OUR NEW JERSEY WAREHOUSE CONDITION: SUPERB* Machine Location: HARRISON. NJ Click Here For More Br
|
|
|
Bridgeport Series I 3-axis CNC Mill with Fagor 8055 Control
Precision Bridgeport 3-axis CNC Mill with Fagor 8055 control. This is a one-owner mill put together by and purchased new from MSC Industrial Supply in 2007. This mill was and is still being used for light duty in a scientific laboratory and may have seen about 250 hours of use at most. The current version of this mill/control combination is selling at mscdirect.com for ~$38k. You will receive all manuals and accessories for this mill and a rotary three phase inverter if you need it. If you are interested. We can discuss workholders and tools. Serious inquiries only. CNC Milling Machines; Spindle Speed Control: Variable Speed Pulley; CNC Controller Brand: Fagor; CNC Controller Model: 8055; Table Length(Inch) 48; Table Width(Inch) 9; Phase: 3 Spindle Speed Control Variable Speed Pulley CNC Controller Brand Fagor CNC Controller Model 8055 Table ... moreLength(Inch) 48 Table Width(Inch) 9 Phase 3 Longitudinal Travel(Decimal Inch) 36.0000 Cross Travel(Decimal Inch) 12.0000 Knee Travel(Inch) 16 Spindle Travel Length(Inch) 5 Spindle Taper Size R8 Quill Diameter(Inch) 3-3/8 Horsepower(HP) 3.00 Shipping charges are estimated and will be determined once the destination is known. This item will ship freight or local pick up.
|
|
|
Bridgeport CNC 2 Axis Mill with ProtoTrak Ctrl - ship free up to 1000 miles
BRIDGEPORT SERIES II CNC VERTICAL MILL GENERAL SPECIFICATIONS: MANUFACTURER. BRIDGEPORT TABLE SIZE. 9" x 42" X TRAVEL. 32" Y TRAVEL. 12" QUILL TRAVEL. 5" KNEE TRAVEL. 16" SPINDLE MOTOR. 1.5 HP SPINDLE SPEED. 60- 4200 RPM QUILL DIAMETER. 3.25" EQUIPPED WITH: PROTO TRAK PLUS CNC CONTROL power draw bar Specifications subject to buyer verification Machine can be inspected under power in warren MI Price is loaded FOB our warehouse Please call with any questions Equipment-Specialists Big Dog Machinery 248-225-2906 All offers will be considered.
|
|
|
3 Axis Bridgeport Vertical Knee Mill CNC with Centroid M-39 Control
This is a 2004 Bridgeport Vertical Knee Type CNC Milling Machine with a 9'x 49' Table with travels of Z=5' Y=12' X=30' It's retrofitted with a 2012 Centroid M-39 Control with precision Ball Screws on all axis and new drive motors. The retrofit was done by Babin Machine located in Brockton Mass. I bought this machine for a backup. I ran this myself machining Plastics and Aluminum parts. It's a sweet machine very user friendly with conversational programing and also can post programs via flash drive or RS-232 using offline programing like Master-Cam or other comparable CAD software I also have all Manuals and this machine comes with a 6' Kurt Vise and R-8 Colletts. Please come see this Machine Run if you like. Also I have added a video link of this machine machining a Brake pad Die and also a quick description ... moreof the Machine Functions.Thank You http:youtu.be/lX1dL2Ks0ro
|
|
|
Chevalier Milling Machine Knee Mill Cnc Mach3 Mach Motion Bridgeport Haase
For sale is a very nice chevalier falcon mill. It has been updated to a new control with teco av servo motors and drivers. Has a Mitsubishi d700 vfd for variable spindle motor rpms. Control is powered by Mach3 and a Apollo 3 motion controller board. Has a part probe that comes with the mill. Have lots of holders that are in the picture most are brand new. Have a bunch of collets that go with mill too. X stroke is 33 inches y is 16 spindle z is 7 inches table z or w is 17.5. Has a Kurt power lock retention system. Has an automatic lube system. Has a electric power assist for moving table up and down. Has flood coolant. Wired up for 230v 3 phase. Computer is a hp touch smart 600 touch screen. Any questions please ask.
|
|
|
BRIDGEPORT 42" X 9" SERIES 1 1HP VERTICAL MILL w/ TRAK AGE 2 3-AXIS CNC CONTROL
BRIDGEPORT SERIES 1 VERTICAL 42" x 9" Chromed Table. No Markings on table, clean 1 Horsepower Step-Pulley Motor(200v. 230v, 380v, 460v- 3 Phase) PROTO TRAK AGE 2 3-Axis CNC Controller/DRO Acurite Glass Scales on all 3 Axis SPINDLE: R8 EQUIPPED WITH: KURT D688 6" wide x 8.8" open Material Workholding Vise Chromed Table and Ways Coolant System Power feeds are controlled by TRAK AGE 2 CNC Controller on both the X and Y Axis. Controller prompts you for action on Z axis. Z axis powerfeed. Which works as the third CNC axis, can be added by an approved Southwest Industries distributor prior to us shipping the mill for an additional $1,200 which includes parts, installation and calibration. You will receive a one year warranty on the newly installed z-axis if you decide to go that route. We have a direct relationship with SWI[manufacturer ... moreof PROTO TRAK controls] and can get you any parts you may need for this TRAK AGE 2 system in the future) This mill has lived the majority of its life in a master machinist home workshop. The machine is in excellent overall condition. Never abused. Never used very much. Really a gem of a find. Please call us at 858-754-8321 if you have questions in regards to this machine. Currently under power and available for inspection in El Cajon. Ca 92020. PLEASE CALL FOR FREIGHT QUOTE! WE CAN SHIP THIS MACHINE ANYWHERE IN THE USA. LOADING IS NOT INCLUDED.
|
|
|
Bridgeport Acurite Millpwer MP2 2-Axis CNC Knee Mill (2003 Control)
THIS ITEM IS OWNED BY AND LOCATED AT MACHINESUSED.COM. 2410 Niagara Lane, Plymouth, MN 55447- CONTACT US TO DISCUSS THE MACHINE AND TO ARRANGE INSPECTION OR PURCHASE AT 763-745-1166 OR EMAIL US. Bridgeport Acurite Millpwer MP2 2-Axis CNC Knee Mill(2003 Control) Manufacturer: Bridgeport. Model# Accurite MP2. Age: 1991. Specification: Control Accurite MP2. Table Size 9" x 42" Machine Travels(X/Y) 30" x 12" Programmable. Quill Travel 5" Knee Travel 16" Spindle To Table Distance 2.5" 22.25" Spindle Taper R8. Spindle Speeds Infinitely Variable 60- 4.200 RPM. Spindle Drive 2HP. Equipped With: Accurite Millpwer MP2 2-Axis CNC Control(CONTROL NEW 2003) Z-Axis Readout, 60- 4,200. RPM Infinitely Variable Spindle. Power Quill Feed, Kurt Power Draw Bar, Servo Powered Knee, Bijur 1 Shot Lube System. Manual. Electrics: ... more220 Volt. 3 Phase Machine/ 115 Volt, Single Phase Controls. Approximate Machine Dimensions: 72"L x 72"W x 88"H. Approximate Weight: 2500 lbs. Location: Plymouth MN. FOB Open Top Truck.
|
|
 |