|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: New Location: Chino, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Weight: 8.5Kg. Good stability. Your satis faction is our ... moreultimate goal. Due to the different display and different light, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: New Location: New York, United States Very Robust Quality Item in Cast Iron.
Buy It Now
$28.00 Shipping Condition: Used Location: Harwinton, United States Tailstock Tap/Die Holder. South Bend, Atlas Lathe This Tailstock Tap/Die Holder will cut threads with either a tap or a die using a hand held holder that ... moreslides on a tailstock mounted arbor. Releasing ones grip allows the tap or die to rotate on the arbor with the spindle. For larger threads that cannot be hand held a stop handle that bears against the lathe compound prevents rotation as the threads are cut The photos below show this procedure. I've sold over 140 of these tools with excellent feedback comments from all. To see for yourself I suggest you check my feedback and read some of the remarks. Below is a photo of the seven(7) pieces that make up the complete Tailstock Tap/Die Holder. The seven(7) pieces are as follows: Tailstock Arbor with#2 Morse Taper. 5/8” arbor diameter Sliding Knurled Sleeve. 1” diameter with 5/8” thru bore Small Tap Chuck. 0 to 1/4“ tap capacity Large Tap Chuck. 12 to 1/2” tap capacity Small Die Holder. 13/16” die diameter Large Die Holder. 1” die diameter Threaded Stop Handle. Fits the sliding knurled sleeve The two Tap Chucks grip the tap by the taps square like inserting a tap in a hand held tap wrench. All small taps from#6 and under have the same size shank and square. So this tool will accommodate all taps#000 to 1/2. Tapping or die threading is relatively easy. As with any threading. Liberal use of cutting oil is recommended along with a slow spindle speed. For the smaller sizes the hand held knurled sleeve, with the tap or die installed, is pushed into the work piece, as the thread starts, the spindle rotation draws the tap or die towards the head stock cutting the thread. When the thread bottoms or comes to the designated length of thread, the operator releases his grip and the knurled sleeve, along with the tap or die rotates with the spindle until the lathe is stopped. Reversing the spindle backs the tap or die out toward the tailstock as the knurled sleeve is again gripped by the operator’s hand. For larger taps and dies. That cannot be hand held because of the
Buy It Now
Free Shipping Condition: New Location: Chino, United States Center Height: 65mm. Top:Use Mo-type 2 Top. Your satis faction is our ultimate goal. Center height65MM. MPNDoes Not Apply. Topuse Mo-type 2 top.
Buy It Now
$18.00 Shipping Condition: Used Location: Plainville, United States Tailstock Centerline Roughly 5-1/2”
$10.75 Shipping Condition: Used Location: Ellington, United States 28mm Body OD. No Reserve!
Buy It Now
Free Shipping Condition: New Location: Madison Heights, United States
Buy It Now
$25.00 Shipping Condition: Used Location: Pipersville, United States turret tailstock from an atlas /craftsman 10 inch lathe ,complete no damage needs cleaning
Buy It Now
$14.99 Shipping Condition: Used Location: Lombard, United States Nice shape hardly used. Please see photos for details. Thanks for looking
Buy It Now
Free Shipping Condition: New Location: Chino, United States Features： Center height: 65MM Telescopic stroke: 45MM Top: use Mo-type 2 top Accessories: with axial locking wrench (pictured) Weight: 2.5KG.
Buy It Now
$8.79 Shipping Condition: Used Location: Harrison, United States FROM A MACHINIST ESTATE. ROTARY TABLE.
Buy It Now
Free Shipping Condition: Used Location: Bridgewater, United States South Bend 9" Metal Lathe Tail Stock Assembly Tailstock It has some surface wear and small pitting. See pictures. It is in fine working condition ... morewith some wear. The tail stock assembly is o ff of a South Bend 9" Metal Lathe. It is sol d as pictured. See pictures. Please e-mail me with any questions or for additional pictures. Winning bidder pays $1 4.00 for USPS Priority Mail Shipping with Delivery Confirmation within the United State s. I will ship this item to the United States only and will not ship it i nternational ly. I accept Paypal. Payment must be received within 5 days of auctions end. Thank you for looking. E-mail me with any questions.
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Specification: Type: Lathe Centers Model: MT1/MT2 Live Center Material: Steel Shank Type: for Morse Taper Quenching hardness: 45-50 HRC Color: Silver ... moreAngle: 60 Package included: 1x MT1/MT2 Live Center.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Features： Center height: 65MM Telescopic stroke: 45MM Top: use Mo-type 2 top Accessories: with axial locking wrench (pictured) Weight: 2.5KG.
Buy It Now
$50.00 Shipping Condition: Used Location: New Castle, United States MACHINIST TOOLS * TAILSTOCK * YUASA * 553-301. Condition is Used. Shipped with USPS Ground Advantage.
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Very Robust Quality Item in Cast Iron.
$30.00 Shipping Condition: Used Location: Tucson, United States This is a GRIZZLY 6" Vertical & Horizontal ROTARY TABLE H7527 from an estate in Green Valley, AZ. Table only! Very nice condition. Possibly unused but ... moreit does have a few small stains on the table.
Buy It Now
$13.00 Shipping Condition: New Location: Eagle, United States Hardened steel bar ends are precision ground after assembly for superior accuracy. Bar made from high strength aluminum.
Buy It Now
$8.70 Shipping Condition: Used Location: Crookston, United States Good used handle for the quill lock on a Monarch 10ee lathe.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Weight: 8.5Kg. Good stability. Your satis faction is our ... moreultimate goal. Due to the different display and different light, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: Used Location: Mansfield, United States MAKER - CRAFTSMAN / DUNLAP. CAST IRON CONSTRUCTION. GOOD USED CONDITION WITH NORMAL USAGE WEAR AND AGE. SPINDLE/RAM MOVES IN/OUT AS INTENDED (COULD STAND ... moreTO BE POLISHED UP & OILED), HAS SURFACE RUST, SCUFFS/SCRATCHES, DENTS/DINGS, PAINT WEAR, STAINING.
Buy It Now
$5.25 Shipping Condition: Used Location: Nashville, United States Atlas 6" Lathe Tailstock Arbor Lock Lever Handle 1.35" This listing is for a Atlas 6" Lathe Tailstock Arbor Lock Lever Handle 1.35" ... morelong with nice chrome as shown in the photos. It is threaded for 1/4" X 20 TPI. There were two sizes of this handle- the one in this listing measures about 1.35" from end to end. The larger one measures about 1.92" and I have one of those listed as well. The lathe I took this off of was a Atlas lathe. But it fits many lathes. Check my other listings under"Lathe Parts" I am happy to combine shipping to save you money-just let me invoice you before you pay. $2.95 Flat Rate Shipping anywhere in the USA. Sellers note: Feel free to ask questions during the auction if you need more information! I take care to present accurate pictures and accurate descriptions. If a buyer finds the description to be inaccurate I will accept returns and refund the item price. Feedback: Since some buyers are not interested in feedback. I choose not to burden them down with more of it, but I leave feedback as soon as the buyer does!
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Weight: 8.5Kg. Good stability. Your satis faction is our ... moreultimate goal. Due to the different display and different light, the picture may not reflect the actual color of the item.
Buy It Now
$14.00 Shipping Condition: Used Location: Fayetteville, United States
Buy It Now
Free Shipping Condition: Used Location: Portland, United States This works well. It’s a #3 morse taper but it also has a #4 morse taper adapter. It easily rotates between the positions.
Buy It Now
$19.99 Shipping Condition: Used Location: Hamilton, United States Both have what might be letters?. I took pics if you can decipher it. The bottom of one has the #18 and the other #18 206.
Buy It Now
$18.99 Shipping Condition: Used Location: New Britain, United States As shown in pictures. Base to center of ram is 4". From a Simonet lathe
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Shank Size : MT3. New Improved Model, has double bearing revolving live center with hardened point. NEW IMPROVED MODEL . Hardened & Ground Shanks.
Buy It Now
Free Shipping Condition: Used Location: Glendale, United States
Buy It Now
Free Shipping Condition: New Location: Perth Amboy, United States Why Choose VEVOR?. VEVOR 300MM Linear Scale For Milling Lathe Machine Accuracy Grinding Linear. 550W Forceful Motor & Variable Speed & Sturdy Nylon Gears. ... morePower of Motor: 550W DC Single Phase. Through high frequency quenching process and precision grinding of high-quality cast iron bed.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Weight: 8.5Kg. Good stability. Your satis faction is our ... moreultimate goal. Due to the different display and different light, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Weight: 8.5Kg. Good stability. Your satis faction is our ... moreultimate goal. Due to the different display and different light, the picture may not reflect the actual color of the item.
$22.15 Shipping Condition: Used Location: Umatilla, United States Lathe tailstock out of local estate . Great overall shape .
Buy It Now
$8.70 Shipping Condition: Used Location: Massillon, United States Up for bid is a Craftsman Dunlap model 109 lathe tail stock assembly 1/2" x 20 TPI spindle. Good shape. Not the original handle. Free shipping to ... morethe lower 48 states.
Buy It Now
Free Shipping Condition: New Location: United States 60mm / 2.36in(longest). 50mm / 1.97in(with scale). 110mm / 4.33in. 25mm / 0.98in. ADJUSTABLE POSITION: Installed on the lathe tail and moved longitudinally ... morealong this rail to adjust its working position.
Buy It Now
Condition: Used Location: Pomona, United States DISTANCE BETWEEN CENTERS 36". POWER FEEDS BOTH CROSS & LONGITUDINAL. 72"L x 32"W x 50"H. CROSS-SLIDE TRAVEL, PLUNGE 4.7". Wheeler Machinery Sales, Inc. ... moreSPINDLE BORE 1.50". SPINDLE MOTOR 3 HP (DIRECT DRIVE).
Buy It Now
$900.00 Shipping Condition: Used Location: Bristol, United States Tailstock fits MT3. Will come with a quick change tool post, live center, drill chuck, and cutting tools. See all pictures for the best description, especially ... morethe last one for more information. Came out a shop in good working condition. Our mechanics power it up to make sure everything works as it should before shipping out as well. Shipping is just an estimate, so contact me for a quote if interested. Will be shipped on a pallet by truck via freight. Local pickup is always welcomed. Check out my other listings for mills, lathes, grinders, and more. Thank you for looking
Buy It Now
Free Shipping Condition: New Location: United States Feature: 1. 60mm / 2.4in (longest). 40mm / 1.6in (with scale). 90mm / 3.5in. 22mm / 0.9in. 1 x Handle Screw.
Buy It Now
Free Shipping Condition: New Location: Vishnu Garden S.O, India 1 Pcs - REVOLVING CENTRE. 2 Pcs DRILL CHUCKS 1.5 - 13MM CAPACITY. Situated at the industrial hub of INDIA we specialize in providing complete tooling ... moresolutions. Our product is manufactured by us, we do not compromise on quality, the quality is the best you can ever get, kindly refer to the photos.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Features： Center height: 65MM Telescopic stroke: 45MM Top: use Mo-type 2 top Accessories: with axial locking wrench (pictured) Weight: 2.5KG.
Buy It Now
$35.00 Shipping Condition: Pre-owned Location: Amarillo, United States Extras included are a polish wheel adaptor with hex key to install on motor shaft, a polish wheel, info on motor, and motor brushes. Base footprint is ... more13.5" wide and 11" deep.
Buy It Now
Free Shipping Condition: New Location: United States A New Tailstock Assembly, Can DIY Products, Handmade Lathe. Specification: Material: cast iron, copper Tailstock stroke: 0-90mm Center height: 100mm Through ... morehole: 20mm Size 205 * 160mm Weight: 8.5Kg Installation taper: MT3 Scope of application: woodworking and polishing Applicable materials: iron, copper, aluminum Features: 1.Good stability 2.Fast top tightening 3.Rapid retraction 4.Lockable Package Includedss: 1×Tailstock assembly Reminderss: Operation method of tailstock center: turn the white spanner left and right, the maximum stroke is 90mm. Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding. Due to different produci.
Buy It Now
$13.15 Shipping Condition: Used Location: Joplin, United States Craftsman Dunlap Dunlop 109 6" Metal Lathe Tailstock The tail stock is in good used condition. It only includes the items that are pictured. It has been ... morecleaned up and I think the pictures accurately reflect the quality/ condition of the tailstock.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Installation taper: MT3. Rapid retraction. Material: cast iron, copper. Fast top tightening. Your satis faction is our ultimate goal. Due to the different ... moredisplay and different light, the picture may not reflect the actual color of the item.
Buy It Now
$20.30 Shipping Condition: Used Location: Richboro, United States Very Nice Tailstock. Base measurements. 2.356 X 3.490 Mounting Key .437 Center Line 3.581
Buy It Now
Condition: Used Location: Louisville, United States EISEN CTL-618EVS Super High Precision Toolroom Lathe(Hardinge HLV style) Spindle run out within 50 millionths of an inch(0.0015mm) Hardened and precision ... moreground spindle mounted on high-precision preloaded angular contact ball bearings maximizes rigidity and sustained precision Infinitely variable spindle speed provides desired speed on demand Fast lever collet closer allows chucking with one single movement Independent electric variable feeds for carriage and cross slide provide freedom of operation Automatic carriage feed driven by AC variable frequency drive motor Hardened and precision ground alloy steel bed ways resist wear Turcite-B slideway bearing surface between carriage and bed Inch/Metric quick change gearbox Inch/Metric dual dial and quick-action compound slide for threading Automatic thread length control Spindle Capacity with Jaw Chucks, 6” Spindle Capacity with Expanding Collets, 3” Spindle Capacity with Round 5C Collets, 11/16” Spindle Capacity with Hexagon 5C Collets, 7/8” Spindle Capacity with Square 5C Collets, 3/4” Spindle Capacity with Step Chucks, 1 1⁄16” ~ 6” Spindle Nose Diameter, Ø 2.189” Spindle Nose I.D. O.D. 5C(10˚) 4˚ Taper Variable Spindle Speed w/ 5C Collet, 0 ~ 4000 rpm Variable Spindle Speed w/ 6” 3-Jaw Chuck, 0 ~ 3000 rpm Hole through Spindle, 1¼” Distance between Centers, 18” Swing over Bed, 11” Swing over Carriage, 9” Swing over Cross Slide, 6” Carriage Power Feed Range, 3⁄16” ~ 4” per minute Cross Slide Power Feed Range, 5⁄16” ~ 7” per minute Cross Slide Travel, 6” Quick-Action Compound Slide Travel, 0.1” Compound Slide Travel, 3” Tailstock Spindle Diameter, 1.358” Tailstock Spindle Taper, MT#2 Tailstock Spindle Travel, 3¾” Coolant Pump, 1⁄8 HP. 220V, 3PH Lead Screw Diameter, 1” 8 TPI) Main Motor, 3 HP. 220V, 3PH D.C. Feed Motor, 110V. 70W Metric Threads(mm) 36 kinds0.275. 0.2875, 0.30, 0.325, 0.35, 0.375, 0.40, 0.4375, 0.45, 0.50, 0.55, 0.575, 0.60, 0.625, 0.65, 0.675, 0.70, 0.75, 0.80, 0.875, 0.90, 1.0, 1.1, 1.15, 1.2, 1.25, 1.3, 1.35, 1.4, 1.5, 1.6, 1.75, 1.8,
Buy It Now
$8.70 Shipping Condition: Used Location: North Tonawanda, United States Thank you for considering to support our family and small business. With a household of 8 we cannot express how grateful we are for your business no matter ... morehow big or small your contribution is. THANK YOUI do combine shipping. There is a couple of options. You can…- Add the items to your cart and check out. When I ship (same day) I’ll refund the difference. (Preferred & cheapest)- You can add to your cart and go to checkout. On the payment page you should have the option to either request total or contact buyer. ( depends on your device ). After that I will send an invoice… many times I don’t get the notification so it takes a little longer.
Buy It Now
Free Shipping Condition: New Location: Dayton, United States This item is one 2MT Crotch Center. Nothing else included. This item is one Crotch Center. Made by Dave from YouTube's Crafted Channel. I own many Atlas ... morelathes on which to test my parts. I have run plastic parts including my ABS gears and change gear bushings for over 4 years making big cuts.
Buy It Now
$8.70 Shipping Condition: Used Location: North Tonawanda, United States ATLAS 10/12 In. LATHE PART No. 9-7 TAILSTOCK CLAMP& BOLT ASSEMBLY The photos are accurate to each description and exact to what you will receive. ... morePlease feel free to email with any questions! Money back guarantee
Buy It Now
Free Shipping Condition: New – Open box Location: Richmond, United States Delta 46-700 Lathe Tailstock Quill Ram part number 434-08-106-0001. New old stock, never used, however will have some light oxidation and rust from open ... morelong term storage.
Buy It Now
$60.00 Shipping Condition: Used Location: Bristol, United States Not sure what lathe it fits. Has a 5 1/4” center line. V to V is 5 1/4”, with total width being 6 3/8”. See all pictures for the best description. Check ... moreout my other listings as well. Thank you for looking
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Shank Size : MT2 / 2MT / Morse Taper 2. Situated at the industrial hub of India we specialize in providing complete tooling solutions. The Die Holders ... moreTravels Smoothly over the Straight Shank. Will Hold Split Button Dies Of Size:13/16”, 1”, 1-5/16" & 1-1/2".
Buy It Now
$6.75 Shipping Condition: Used Location: New Britain, United States As shown in pictures
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States 2MT 283mm (11-1/8”) 0.0002”. 3MT 335mm (13-3/16”) 0.0002”. 1MT 151mm (5-15/16”) 0.0002”. Shank Overall-Length Max. Hawkwerkzegue comprises of a dedicated ... moreand skilled team of engineers with an aim of providing you tools of highest indian industrial standards.
Buy It Now
$24.99 Shipping Condition: Used Location: Union Grove, United States Atlas 618 / Craftsman 101 (6").
$18.40 Shipping Condition: For parts or not working Location: Runnells, United States Left over tailstock cross slide belt and Gibbs. What you see is what you get
Buy It Now
Condition: Used Location: Westcliffe, United States This is a Schaublin 120 VM engine lathe made in Switzerland to very high standards. The 120 VM is a very heavy, rigid machine capable of doing very nice ... morework. It has the finest feeds of any lathe that I have ever used.
Buy It Now
$7.00 Shipping Condition: Used Location: Tewksbury, United States
Buy It Now
$19.34 Shipping Condition: Used Location: Los Angeles, United States
Buy It Now
$97.92 Shipping Condition: Used Location: Nassau, United States Sn-45 lathe tail stock Please ask questions before bid, sold as-is.Will offer discount if buying other sn-45 items.I have a sn-45 that fell on control ... moreside, ask about any other parts neededThank you
|
|
|
|
G & L outboard support tail stock
G&L outboard support. Fits model 340/350 mills Box way size is 2" thick x 8" wide each x 36" overall width. Support has a bronze bushing in it with a 2.500 bore. Bushing can be removed and the casting has a 4" bore 60" vertical travel. Support is in excellent condition. We will also accept best offers. buyer is responsible for all shipping charges and buyer is also to arrange for shipping. pick up only. We will not ship. we will load on truck
|
|
|
4" ADJUSTABLE TAILSTOCK CENTER DIVIDING HEAD TAIL STOCK for ROTARY TABLE MILL
This auction is for a good used tailstock. 4" ADJUSTABLE TAILSTOCK CENTER DIVIDING HEAD TAIL STOCK for ROTARY TABLE MILL 4" height. Approx. 5/8" travel. In good working condition. Works smoothly paint shows some wear
|
|
|
Clausing Lathe 5900 Series tail stock-NICE
Excellent used tail stock for a 5900 series Clausing Lathe-Complete
|
|
|
MACHINIST MILL LATHE TOOL Dividing Head Index Indexing Tail Stock p
PLEASE SEE MY OTHER AUCTIONS FOR A LARGE SELECTION MACHINIST ITEMS. I WILL COMBINE SHIPPING. THE EBAY SHIPPING CALCULATOR MIGHT BE WRONG, PLEASE WAIT UNTIL I SEND THE INVOICE AT THE END OF THE SALE. I do not know much about these so I am selling it AS IS with no returns. The pictures show all that is included and the condition so please look close. Please see my other auctions for more tools items from a local estate. I will combine shipping. Contact me for a shipping quote. I tried to take photos of the parts that came with it. if there are any questions, please do not hesitate to email me with any questions.PLEASE SEE THE PHOTOS FOR THE BEST DESCRIPTION. Sold"AS IS" with NO REFUNDS OR RETURNS! NO EXCEPTIONS. I will combine shipping. Please email me for combined shipping rates. PLEASE KNOW THAT I TRY TO SATISFY ANY AND ALL OF MY ... moreCUSTOMERS. IF THERE IS A PROBLEM WITH YOUR PURCHASE, OR ANY OTHER QUESTIONS, PLEASE, DO NOT HESITATE TO EMAIL ME. I ANSWER ALL EMAILS AND WILL TRY TO WORK WITH YOU AS BEST I CAN. I WILL, HOWEVER, NOT BE BULLIED OR BLACKMAILED. THERE SEEMS TO BE SOME BUYERS THAT TRY TO SHAVE MONEY OFF OR CLAIM THINGS THAT ARE NOT TRUE. SO PLEASE, IF YOU ARE ONE OF THESE PEOPLE, DO NOT BID. BT
|
|
|
Tail Stock Adjustable MACHINIST MILL LATHE TOOL Dividing Head Index Indexing
Yausa Tail Stock. Adjustable Center. MACHINIST MILL LATHE TOOL Dividing Head Index Indexing 553-301.
|
|
|
Clausing Lathe 6500 series 13x36 Tail stock 13" colchester
This is a good tailstock with a 4" stroke and marked in MM and standard not worn out. Any questions just ask. Thanks
|
|
|
Tailstock 3 1/2" Center cnc rotary table milling tail stock atlas index fixture
Nice functional tailstock. 3 1/2" center. Ask nay questions in advance. Thanks for looking. Free Shipping in the lower 48.
|
|
|
MACHINIST BROWN & SHARPE INDEXING DIVIDING HEAD w TAIL STOCK & 7" CUSHMAN CHUCK
Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 UP FOR AUCTION: PRECISION MACHINIST TOOLS& PARTS MACHINIST TOOL BROWN& SHARPE INDEXING DIVIDING HEAD COMES WITH TAIL STOCK& 7" CUSHMAN CHUCK ZOOM INTO PICTURES TO SEE CONDITION OF THESE PIECES THIS PICES CAN BE SHIPPED FED EX GROUND WEIGHS ABOUT 150 POUNDS. PLEASE CONTACT ME DIRECTLY FOR SPECIFIC SHIPPING COSTS! PLEASE REFER TO ALL PICTURES TO SEE CONDITION& SEE EXACTLY WHAT IS INCLUDED IN YOUR PURCHASE* THIS PIECE CAME FORM A VERY WELL MAINTAINED MACHINIST SHOP. I will combine shipping for more than one purchase. Please look at our other listings we have a large array of machinist tools up for auction and we add new items every week. PLEASE KNOW THAT I TRY TO SATISFY ANY AND ALL OF MY CUSTOMERS. IF THERE IS A PROBLEM WITH YOUR PURCHASE. OR ANY ... moreOTHER QUESTIONS, PLEASE, DO NOT HESITATE TO EMAIL ME. I ANSWER ALL EMAILS AS SOON AS POSSIBLE IF I HAVE THE ANSWER AND WILL TRY TO WORK WITH YOU AS BEST I CAN. WE ALWAYS TAKE GREAT CARE IN PACKING& SHIPPING YOUR PURCHASES. LOOK AT OUR EBAY FEEDBACKS. AUCTION WINNER CAN CONTACT ME DIRECTLY IF THERE IS A PROBLEM. Please wait until auction has ended and invoice has been received to confirm all costs to buyer. Purchases over $80 should be insured to guarantee delivery. We are willing to ship anywhere! Please refer to USPS website for exact pricing from area code 07005. We try to use flat rate boxes when possible. Being SOLD AS IS– Do not know much about machinist tools but describe as best I can. I am in the learning process. IF LISTING IS INCORRECT PLEASE CONTACT US, any feedback will be appreciated.
|
|
|
Tail Stock, 7 1/2" Center Line A-1124-25
You are bidding on a Tail Stock Specifications Good Condition Good Condition: Item is free of any significant dents. Marks, imperfections that would impair the functioning of the item(unless specified in the description) Good Usable Condition: Item may have dents. Marks, imperfections that do not impair the functioning of the item(unless specified in the description) Machines/Tools that cost above $500.00 please pay with credit card or wire transfer. We guarantee that the item purchased is packaged exceptionally well. Once it is picked up by a common carrier(UPS etc) we lose control over how the item is handled. If you receive an item and it(or the box) appears damaged. Do not sign or accept. If the item is left at your home or business. And you later find that it is damaged, take pictures and notify the carrier. If you are pleased with our ... moreservice please leave positive feedback. Thank you. inkfrogproseries. The machine/item is located in Bay Shore. NY 11706 Shipping costs to buyer location are not included with the machine price We can provide a freight quotation, buyer works directly with the shipper Crating/Palatalizing: Some buyer's need to use a freight company requiring the item to be crated or palatalized. If this is required, we quote crating or palatalizing separately and it is not included with the sale price. We'll quote per customer requirements, customer shipping method& machine design. Shipping can be confusing. Relatively inexpensive, but heavy items, can cost more to ship than the item itself. Our experience is to allow 1-2 weeks for freight delivery. Please contact us at info@sagmachinery.com or give us a call at: 1-631-586-1768 OR 1-800-334-0175 if you have any questions about shipping. Upon arrival of your machine. Unpack and immediately check for visible damage. Call Sag immediately– you will need to take pictures and email to info@sagmachinery.com. Make sure you note on BOL BEFORE the driver leaves. We accept paypal(info@sagmachinery.com)Or just give us a call at 1-800-334-0175 or
|
|
|
Hardinge lathe attachment threading tail stock
Hardinge lathe attachment. Never seen one before and not sure what to call it or if its complete. sold as is. I was told it was a thread cutting attachment. check ruler in photo to confirm bed size so you will know if its the right size for your lathe. We are open 9am to 5.30 pm mon-friday. You can pay by credit card by calling 727-417-0172
|
|
|
CINCINNATI 8" DIVIDING HEAD WITH TAIL STOCK
CINCINNATI 8" DIVIDING HEAD WITH TAIL STOCK
|
|
|
Haas SL30-TB Big Bore with Tail Stock
2004 HAAS SL-30T BIG BORE Chuck Size 15" Max Diameter Bar Capacity 4" Max Swing Over Bed/ Carriage 30" 14.5" Max Turning Diameter 16" Distance Between Centers 39" Max Machining Length 31" Tools 12 Spindle Motor 40 HP Spindle Speed 2500 RPM Spindle Bore 4.62" Spindle Nose A2-6 Spindle Torque 407 ft. lbs. Rapid Traverse Rates(X& Z) 710 IPM X-Axis Travel 11.3" Z-Axis Travel 33.5" Tailstock Taper MT#4 Machine Dimensions(L x W x H) 162" x 77" x 74" Machine Weight 16.000 lbs. FEATURES: HAAS CNC CONTROL 15" Color TFT 3.5" Floppy Disc Drive 15" Kitagawa Hydraulic Chuck 4" Dia. Bar Capacity Big Bore Spindle Option Fully Programmable Hydraulic Tailstock Hennig Chip Conveyor(Side Exit) Chip Auger Tool Presetter Visual Quick Code Programming 1 MB Memory High Intensity ... moreLighting Barfeed Interface Spindle Orientation Bolt-on Turret
|
|
 |