|
DELTA ROCKWELL 17" DRILL PRESS UPPER POWER HEAD SPINDLE ASSEMBLY - VINTAGE
Delta 17" drill press upper power head/ spindle assembly. I believe this came off a drill press manufactured in the mid to late 1960's. The manual which came with it is dated 1966. Drill press serial number is SN# 119-4043. The power head is in good overall condition with no broken or cracked parts. One small machine screw is missing holding the tightening lever onto its splines shaft that adjusts the tension holding the power head onto the drill presses post/ column. This is on the left side of the power head if looking at its front. All parts a functioning very well. The spring return on the return stroke is smooth and even. Spindle bearings are in very good shape and run freely. The spindle is true and the chuck runs with any run out. Comes with Jacobs chuck number#633 with a 1/2" capacity, and a Jacobs#3 series chuck key. ... moreIncluded also is the stepped pulley for the spindle though the largest pulley has two very slight dents in the upper rim of the pulley one might be able to file these out. Only two bolts on the rear motor mounting plate are with it. I don't have the motor, upper guard, or the other stepped pulley. Drill press mounts on a 2-3/4" column or post. The item will be well packed to insure safe delivery. $2 extra will insure the item for $300. Please wait for an invoice before paying. Will ship Fed Ex or UPS.
|
|
|
delta milwaukee drill press dp220 lo speed pulley bearing retainer
used part in good condition.
|
|
|
delta milwaukee drill press quill return spring and cover dp220
good used spring and cover. not too dirty. oil it and use it. di,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishhov%3C%3Edi-141c92eb15e-0xfd-
|
|
|
delta milwaukee drill press hub
hub lets you attach 3 feed handles. Will fit other models. 1 1/4' hole. Good condition
|
|
|
Delta Milwaukee 14 inch drill press multi speed pulley metal working extras!
Ready to go! Plus original paperwork. Pulley was glass bead blasted to clean up and bearing replaced. Bulletin for installation and drill press owner's manual. Hard to find!
|
|
|
DELTA ROCKWELL DRILL PRESS POST COLUMN COLLAR BUFFALO FORGE WALKER TURNER 2-3/4
Drill press post column collar. I believe this is an early Delta drill press collar. But it might also be for a Walker Turner, Buffalo Forge Drill or Atlas press. The casting numbers on the column clamp read D.D.P. 62. There are a few nicks in the collar where it appears the collar was damaged slightly. There are no cracks or breaks in the collar, and it is in otherwise good condition. The damage shouldn't effect the collars performance. Returns accepted. Fits a 2-3/4" column.Will bundle multiple items for cheaper shipping.
|
|
|
DELTA ROCKWELL DRILL PRESS TABLE SUPPORT BRACKET BUFFALO FORGE WALKER TURNER
Drill press table support bracket. I believe this is an early Delta drill press table support bracket. But it might also be for a Walker Turner, Buffalo Forge Drill or Atlas press. The casting numbers on the matching drill press column clamp read D.D.P. 62, this part came from the same drill press but isn't included in this auction. The casting number on this I believe reads 1. The bracket fits a 2-3/4" column/ post. Returns accepted. Will bundle multiple items for cheaper shipping.
|
|
|
Delta Mortising Tool Drill Press Attachment w/ Variety of Chisel Bits & Bushings
From a local estate sale: Delta Accessory Model 17-924 Mortising Attachment. Includes: Chisel Holder, Hold-Down Assembly, Fence, Levers and Knobs, Guides, Small ID Split-Ring Bushings for 10" 12" and 32" Radial Drill Presses, Intermediate Split-Ring Bushings for 14" Drill Presses, Large ID Split-Ring Bushings for 15" and 16-1/2" Drill Presses, Set of four chisels: 1/4" 5/16" 3/8" and 1/2" Hard plastic case, Does not include manual. Fortunately. It's available for printing off of the internet. Excellent used condition. A little dusty. But otherwise no significant signs of use. SHIPPING AND HANDLING TIME We are happy to ship within one(1) business day of receiving payment. HOWEVER. The buyer must elect and pay for Express Mail service when making payment. If the buyer does not elect the ... moreExpress Mail service. Then the merchandise purchased will ship within three(3) business days of receiving payment. Check out our buy-it-now items at RescuedObjects on etsy.
|
|
|
Vintage Delta Milwaukee 17" Drill Press with Power Feed /110 Volt Single Phase
Vintage Delta Milwaukee 17" Drill Press S# 32-6046 with 5 spindle speeds changed by step pulley and 4 powerfeed speeds changed by step pulley(belt needed) Table is very heavy duty with collant collection trough. Easy table height adjustment. Will load on your truck or trailer or help you to arrange shipping. Please ask questions.
|
|
|
delta milwaukee drill press dp220 counterweight assembly
Spring counterweight for head on production table drill press. See the slot on top your head? That's what its for. Could be adapted to other dp220 models. works on 37' or taller column with 2 1/2' I D. See pictures for required 9/16' holes in column. Can be a"picnic" to install(I know how) Does make it easy to raise and lower the head though. Thank you. questions ok. I have 37' columns to sell. Ask.
|
|
|
1 Delta Milwaukee Rockwell Industrial Floor Drill Press Vintage 1725/1425 RPM
Delta Milwaukee Rockwell Industrial Floor Drill Press Vintage 1725/1425 RPM Used. ag6 2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28c%3Eag6%3E2-1432e012554-0xe1-
|
|
|
Walker Turner /Rockwell, Delta Drill Press Pinion & down feed Handle
Walker Turner. Rockwell, Delta PINION& feed handle for 20" and 17" Drill presses, This is a vintage steel Pinion and feed handle from a 20" Walker turner drill press. Rockwell later bought Walker Turner so this plate will fit certain Rockwell/Delta drills(you will have to check which ones) These mounts were produced by Walker Turner in the 1940's and early 1950's on their top of the line drill press. The 1100 series. Worked well and went up and down smoothley. Includes screw in T-shaped pin to lock on the return spring Please see my other auctions for more classic parts. Item will be carefully wrapped and boxed. No charge for handling and I have a FedEx business account so ground shipping will be cheaper than the post office or UPS. You will pay actual shipping costs. I don't pad the bills. Contact me if there ... moreis a question about shipping charges as the shipping. Calculator in the auction is often iaccurate.
|
|
|
DELTA 17-900 DRILL PRESS 12 SPEED 16 1/2" Rotary Table Tilt
DELTA 17-900 DRILL PRESS 12 SPEED 16 1/2" Rotary Table Tilt Floor Model 3/4 HP dhep.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishm%3Ed%7Fhep-1432e012638-0xe5-
|
|
|
Delta Milwaukee DP220 Drill Press Pulley Guard DP 256 rockwell walker turner
Here we have the headstock pulley off of a vintage Delta DP220 Drill Press. Includes the necessary 3 mounting bolts. As you can see in all of the pics. Still in good shape. Posted with
|
|
|
Walker Turner /Rockwell, Delta Drill Press Motor Mounting Plate- Cast Iron
Walker Turner. Rockwell, Delta cast iron Motor Mounting plate for 20" and 17" Drill presses, This is a vintage very heavy cast iron motor mounting plate from a 20" Walker turner drill press. Rockwell later bought Walker Turner so this plate will fit certain Rockwell/Delta drills(you will have to check which ones) These mounts were produced by Walker Turner in the 1940's and early 1950's on their top of the line drill press. The 1100 series. This part is in excellent mechanical and cosmetic shape. Part# HD18 Part was stripped to bare metal with abrasive media(for the iron parts) Then primed with auto primer and painted. All threads were chased. With taps and dies and lubed. Feel free to contact me with any questions. Please see my other auctions for more classic parts. Item will be carefully wrapped and boxed. No charge ... morefor handling and I have a FedEx business account so ground shipping will be cheaper than the post office or UPS. You will pay actual shipping costs. I don't pad the bills. Contact me if there is a question about shipping charges as the shipping. Calculator in the auction is often iaccurate.
|
|
|
WALKER TURNER DRILL PRESS BASE UPRIGHT FREE STANDING - DELTA ROCKWELL
Walker Turner freestanding drill press base. The base is off an older drill press I believe was from the 1950's. The base is in good overall condition. Fits a 2-3/4" post/ column. The base is missing one set screw to fix the post to the base. Serial numbers read 9D943. The base will be well packed to insure it arrives safely.
|
|
|
delta drill press dp220 belt cover
very well made belt cover for dp220. good craftsmanship. good welds.
|
|
|
VINTAGE 14" DELTA ROCKWELL DRILL PRESS QUILL PINION
FROM CAT#14000 FOR REF. 1 1/4" BODY DIA. 13 TOOTH PINION 1/2-20 STEP DIA. FOR SPRING DRILLED HOLE FOR 7/16 HANDLE(NOT PROVIDED) O/A LENGTH 8 5/8 WITH 3/8-24 HANDLE THUMB SCREW LOCK PINION SHOWS HARDENED GREASE WITH NO APPRECIABLE WEAR. FEW MARKS ON BODY O.D. FILED AND POLISHED NEEDS A GOOD CLEAN AND POLISH. GOOD USEABLE PART COMPLETE PART-OUT
|
|
|
DELTA DRILL PRESS HEAVY DUTY VARIABLE SPEED USED
DELTA DRILL PRESS HEAVY DUTY VARIABLE SPEED USED WAS USED ONCE STILL WORKS LIKE NEW SPEED 500-3100rpm MOTOR: V 120 Hz 50 A 6.0 RPM 1720 PH 1
|
|
|
delta milwaukee drill press dp220 slo speed pulley belt guard
belt guard for delta dp220 drill press. will fit slo or hi speed pulley. thank you
|
|
|
VINTAGE CRAFTSMAN DRILL PRESS BASE DELTA, OTHERS, FLOOR MODELS?
BLUE COLOR WAS ORIGINAL ORIGINALLY FROM CRAFTSMAN 15" 101.036261 BENCH TOP. CIRCA 1930'S 40'S. SPEC'S 2 3/4" HOLE FOR COLUMN PIPE. 18" DEEP X 11 1/2" 8 7/8 FROM CENTERLINE OF PIPE TO CENTERLINE OF TABLE. SCALE DIM) BD3A-3 CAST# ON BOTTOM- 1/2 BOLT TO"DRAW" TIGHTEN. LITE RUST, NO CRACKS OR DAMAGE
|
|
|
DELTA RETIREMENT LIGHT BANDSAW DRILL PRESS GRINDER OTHERS MACHINERY LIGHT
ORIGINALLY FROM A 1950'S DELTA DRILL PRESS. NO DAMAGE. WORKS, WITH ROTARY SWITCH. I WOULD REPLACE THE CORD WITH A STRAIN RELIEF ON CORD(IN MY OPINION) 3 BULBS INCLUDED.
|
|
|
BENCH MODEL BASE FOR 14" DELTA DRILL PRESS
Nothing cracked and nothing welded. Very nice base.
|
|
|
WALKER TURNER Industrial DRILL PRESS by Rockwell / delta gang 17 inch
please click then supersize the photos for a good look Rockwell. Walker-Turner Division, Drill Press Catalog Number 67-000 Serial Number 1317049 This was once part of a gang of drill presses in sombody's shop. You will be re-directed off eBay so be sure to add this to your Watched list before clicking the link. I plugged this in and it does run It has different pulleys inside to change gears Includes the chuck. Pick up only. I'm flexible, if you need a few weeks that's fine just let me know when you can get here. As with all my large items. Buyer has the right to change his mind on the day of pick up for any reason without hard feelings from me. Pay me with PayPal or in cash the day of pick up. Whatever is easier for you. M any vintage items listed this week. Click here to see my other listings.
|
|
|
Delta Badge Tag Machinery Drill Press
This is the Delta logo machinery tag from a drill press circa 1970's. Its 2 3/8" diameter.
|
|
|
DELTA MILWAUKEE 14" BENCH TOP DRILL PRESS
RIMCO ROBERT IVENS MACHINERY COMPANY 613 W. Bruce St. Milwaukee WI 53204 414-272-6686 Welcome to Robert Ivens Machinery Company Our Mission: Productive and Satisfied Customers. Up for AUCTION: DELTA MILWAUKEE 14" BENCH TOP DRILL PRESS In good/used condition New bearings all around Runs well and will serve many happy years! Wood workers quill and table STD speed pulleys Original motor with new switch 1/3HP 1 phase 110/220v Serial no. unk. Check photos for details I SHIP ITEMS THIS HEAVY ALL THE TIME. ASK ME FOR A QUOTE! Email us with any questions! WE COMBINE SHIPPING! Check out my! Be sure to add me to your! Robert Ivens Machinery Company(RIMCO) is Wisconsin's largest dealer in used woodworking machinery A sole proprietorship in business for more than twenty-five years, RIMCO's business philosophy is based upon value and customer ... moresatisfaction. If you have an interest in woodworking machinery. You are welcome to call and ask about our extensive. Ever changing inventory. Your business will be most appreciated.
|
|
|
Old Style Delta 14" Drill Press Jacobs Chuck Spindle
Old Style Delta 14" Drill Press Jacobs Chuck Spindle. Cat. No. 972. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press 1/2" Router Spindle
Old Style Delta 14" Drill Press 1/2" Router Spindle. Cat. No. 974. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
VINTAGE DELTA ROCKWELL DRILL PRESS HEAD FOR USE REPAIR AND OR PARTS !!
GOOD CONDITION. ALL QUESTIONS WELCOMED BEFORE BIDDING*PLEASE NOTE*I AM NOT AN EXPERIENCED MACHINIST AND MOST OF THESE ITEMS HAVE BEEN ACQUIRED FROM A RETIRED MACHINIST AND MAY NEED CLEANING.MAY HAVE SOME PITTING OR LIGHT SURFACE RUST,MAY BE INSCRIBED WITH INITIALS& S,REGROUND OR ALTERED,MAY NEED FURTHER METICULOUS CLEANING,MAY NOT BE FULLY ACCURATE AND MAY BE CHIPPED.NEED SHARPENING AND MAY HAVE DUPLICATE SIZES BUT MOST ITEMS SHOULD BE USABLE(UNLESS OTHERWISE INDICATED)AND GOOD FOR AN APPRENTICE OR A SECOND TOOL TRAY AROUND THE LATHE OR MILL OR FOR THE BASEMENT NIGHT SHOP*PLEASE FEEL FREE TO ASK ANY QUESTIONS ABOUT SIZES OR CONDITION OR ANYTHING AND PLEASE CHECK OUT MY OTHER CUTTING TOOLS,TOOLING,TOOL HOLDING,COLLECTIBLES AND OTHER USABLE STANLEY STARRETT,BROWN& SHARPE,LUFKIN ETC MACHINIST'S TOOLS AND OTHER TRADE TOOLS& EQUIPMENT ... moreBY CLICKING BELOW OR ABOVE ONTO"VIEW SELLERS OTHER ITEMS"Please Check out my! NOTE*MORE TOOLS AND STUFF FOR AUCTION IN UPCOMING WEEKS*NOTE I'M TRYING TO STAY AWAY FROM A"BUY IT NOW" PRICE BUT IF YOU ARE DETERMINED PLEASE EMAIL YOUR HIGHEST OFFER(PAY PAL ONLY) AND I WILL ANSWER EITHER WAY.THANKS*AS ALWAYS MULTIPLE PURCHASES WILL DECREASE ALREADY LOW SHIPPING COSTS.PLEASE READ BELOW* IF YOU WOULD LIKE TO CARRY OVER A PURCHASE FROM ONE WEEK TO THE NEXT TO SAVE SHIPPING THAT'S FINE BUT I WILL REQUIRE PAYMENT ONLY ON ITEMS PURCHASED WHILE HOLDING TO KEEP MY EBAY UP TO DATE.THANK YOU FOR YOUR UNDERSTANDING* OVERSEAS SHIPMENTS WELCOMED BUT RESTRICTED TO LIGHTWEIGHT AND SMALL ITEMS ONLY. THERE WILL BE AN ADDITIONAL $4.00 HANDLING FEE ADDED TO THE PRE-DETERMINED INTERNATIONAL SHIPPING QUOTE*INSURANCE MAY BE REQUIRED ON SOME PURCHASES* ALERT*SAVE MONEY $$$$$$$$$$ ESPECIALLY TO COMBINE SHIPPING ON MULTIPLE PURCHASED ITEMS IF ITEM(S) FIT IN THE SMALLEST USPS PRIORITY FLAT RATE BOX OR ENVELOPE I WILL SHIP IT FOR $5.00(UNDER 4 POUNDS)A MEDIUM FLAT RATE PRIORITY BOX $1
|
|
|
Rockwell/Delta 20" Drill Press Y-688
used in good condition what you see is what you get
|
|
|
Rockwell / Delta 2 Station 20" drill press 70-6X0
230V/460V 3phase 1 1/2 HP Motors- 1735rpm 2 Station 20” Height Capacity Stepped pulley heads for variable speed 1 Chuck included Overall table size of 76" x 30" This machine is owned and was used by a small prototype shop. Lack of use and need for space are reasons for sale. Unit on the right side has missing"head travle" crank but spindle up/down works fine. Besides that it was functioning properly when it was disconnected. Please feel free to ask any questions and I can also email more photos if needed. There is a $300.00 security deposit due within 72 hours of the close of the listing. This can be paid with paypal. Certified check, or cashiers check. The full balance is due upon pick-up in cash, certified check, or a cashiers check from your bank that must clear before pick-up or shipping. We do not accept full payment ... morewith Paypal. This machine is being sold AS-IS. This item must be shipped by freight. Buyer responsiable for all shipping cost(we do have fork lift) Please feel free to ask questions and I will do my best to answer them. I can also email more photos. Thank you a;06d2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28%3Ea%3B06d2-1440c67530b-0xd5-
|
|
|
Quill Clamp for a Delta 14" Super Hi-Speed Drill Press
Quill Clamp parts for 1940's Delta Hi-Speed drill press. Part Numbers: SP-604. SP-7, SP-27. DOES NOT INCLUDE SP-26 but this can be easily made on a lathe. SP-26 is just a 3/8"16 knurled nut. The important part is the SP-7 which is no-longer available and is more difficult to make. Find Schematics for this drill at:
|
|
|
15” Delta Floor Type ProductionTable Drill Press, Single Phase
15” Delta Floor Type ProductionTable Drill Press 24” x 30” Table 5” Quill Travel 6 Speeds Approx 1 HP 115 Volt Single Phase Motor Older Drill That Runs Well Inspect Under Power in Our Branchburg NJ warehouse Questions Call dave@ 908-399-8133
|
|
|
Delta Drill Press Pulley System HDP144
This is a Delta Pulley System HDP-144 used to convert an 11" Delta Drill Press and others with the same motor mount size rail mount openings for additional pulley speed gear ratios. The auction is for the adjustable chassis and motor mounts only. The unit will be disassembled and shipped in a Small Flat Rate USPS box at a cost of $5.35. Due to the age of the product the sale will be"As Is. No guarantee is offered or implied. Please look closely at the pictures and ask any questions you may have prior to bidding.
|
|
|
DELTA ROCKWELL DP600 17" DRILL PRESS HANDLE
FROM DRILL PRESS SHOWN IN PHOTO DP600 HEAD. 1 1/4" BORE CAST# DP631 4" OUTSIDE DIA. RETAINED BY 7/16" DIA. PIN 3 ARMS WITH 7/16-20 THREAD AND PHENOLIC BALLS. NO DAMAGE BUT NEEDS CLEAN WITH LITE RUST CHIPPED PAINT
|
|
|
Delta Woodworking Machinery 11-900 Corded 8" Drill Press - USED
Please view pictures and READ AD carefully before bidding on or asking questions about this item! Any further questions. Feel free to ask. Thank you! Hello and thank you for viewing our listing for. Delta Woodworking Machinery 11-900 Corded 8" Drill Press- USED M/N: 11-900 P/N: 1349475 S/N: W9915 This drill press is in good condition and works well. Power cord is attached and included but unfortunately NO bits. Table is adjustable. Great addition to have in your tool box or garage. INCLUDES ONLY WHAT IS SHOWN! There are NO returns on items that are sold for parts! These will ship as seen in the pictures unless otherwise stated! Bid Confidently& Good Luck. P12-19682-3 If you have any questions. Feel free to message me through eBay. Happy bidding! Thank you again for looking at this listing! With all our auctions we strive for a 5 ... morestar experience and would be more than happy to help our cus tomers with any problems they incur with any of our transactions. Please contact us with any problems prior to leaving feedback and we will try to solve any situation you do come across. If you have any questions about the item feel free to ask. Also feel free to look at the store for more merchandise. We also offer local pickup on all items that are listed here on eBay(see details for full info) We do not allow for local eBay customers to enter the establishment where items are held to test the items. We test all items prior to listing to assure that they operate properly and note any errors on the item. Thank you. Bid With Confidence! See Our Feedback! Check out Our Store For More Great Items! AUCTION TERMS AND INFORMATION*PLEASE READ BEFORE BIDDING* Terms: We are an honest seller and do our best to provide the most accurate information in all auctions. If you feel there is an error or need clarification please feel free to contact us. E-mails should be sent through eBay only; we can answer any e-mails outside of eBay as this violates eBay policy. In most cases we are a re-seller not the orig
|
|
|
DELTA DRILL PRESS MORTISE ATTACHMENT WITH CHISEL BIT SET
This auction is for a used. Vintage Delta mortise attachment(DP 300) This fits drill presses with a 1 3/4" quill. The attachment comes with what is shown in the pictures: one 3/8" mortise chisel and bet and the drill press depth stop rod. All parts are in good usable condition. Free expedited shipping to U.S. Thanks for looking.
|
|
|
Delta 32" Radial Drill Press with Stand Model 11-090
DANNY LITTLE BUCK DANNY LITTLE BUCK Delta 32" Radial Drill Press with Stand DELTA 32" RADIAL DRILL PRESS MOUNTED ON A STEEL STAND. Model 11-090 TABLE SWIVELS. LOCAL PICK UP ONLY" EVERETT WA) CAN HELP YOU LOAD IT. Have the manual on my computer. Can Print it out for you. Or email it. This item is in very good condition. And has been tested. PLEASE SCROLL DOWN FOR THE AUCTION DETAILS THIS ITEM IS USED. LOCAL PICK UP ONLY" SHIPPING INFO DOES NOT APPLY FOR THIS ITEM. Photo's are of actual item Please Ask Your Questions before you bid. DON'T LET SOMEONE ELSE STEAL THIS GREAT DEAL FROM YOU. BID NOW! WE ONLY ACCEPT PAYPAL. IF YOU ARE PAYING BY E-CHECK USING PAYPAL. THEN YOUR ORDER CANNOT BE PROCESSED UNTIL THE PAYMENT HAS CLEARED THROUGH PAYPAL. ALL PAYMENTS MUST BE RECEIVED WITHIN 5 DAYS AFTER CLOSE OF THE AUCTION. IF ... morePAYMENT IS NOT RECEIVED AFTER THE 5 DAYS. THEN A NON-PAYING BIDDER ALERT WILL BE FILED, AND THE ORDER WILL BE RE-LISTED. WE WOULD RATHER NOT DO THIS, SO PLEASE ONLY BID IF YOU ARE SERIOUS ABOUT BUYING. THANK YOU ALL SHIPPING COST ARE AS LOW AS POSSIBLE& ARE NON-NEGOTIABLE. WE USUALLY REQUIRE 1-3 BUSINESS DAYS TO PROCESS YOUR ORDER. SO YOU RECEIVE YOUR ITEM QUICKLY. WE SHIP MONDAY THROUGH SATURDAY ONLY. ITEMS WITH PAYMENTS RECEIVED ON SATURDAY OR SUNDAY WILL NOT SHIP UNTIL THE FOLLOWING MONDAY. OR TUESDAY. WE BELIEVE IN RECYCLING, AND RE-USE BOXES WHENEVER POSSIBLE. DOMESTIC SHIPPING UPS does not deliver to P.O. Boxes or FPO/APOs. No exceptions. Please supply a PHYSICAL ADDRESS for delivery. Shipment to Hawaii. Alaska& U.S. Territories are subject to increased costs. All items over $150 must be shipped via UPS including Signature Delivery Confirmation. ALL items shipped via U.S. Postal Service are shipped via First Class. Priority or Media Mail Services, each with Delivery Confirmation. Delivery time is 3-10 business day I USE USPS. UPS, FEDEX FOR SHIPPING, AND ALWAYS ADD A TRACKING NUMBER. THIS INSURES PROVEN RELIABILITY. AND SATISFACTION. ALL SHIPPING AND HANDLING CHAR
|
|
|
VARIETY OF DELTA MORTISING ATTACHMENTS VINTAGE DRILL PRESS ITEMS FROM ESTATE
I am helping my mom clean out my dad's workshop and these items are from there. I am not a tool person so when asked what these are was told DELT MORTISING ATTACHMENTS DRILL PRESS-ONE HAS DP330 ON IT. Please see my pictures of what I am selling. These are very very heavy and will be mailed flat rate.
|
|
|
Delta Rockwell 15 in Drill Press model 15-000 Vintage Floor model Refurbished
Vintage Refurbished ROCKWELL DELTA DRILL PRESS Completely refurbished Model: 15-000 Serial: 1345452 motor model: NJ 62M650 CW HP: 1/2 Volts: 115/230 RPM: 1725 CY: 60 PH: 1 Type: 5CS Frame: 56-5 AMP: 7 0/ 3 5 Temp rise: 50*c CONT LOCAL(TAMPA. FL) PICK UP ONLY buyer is responsible for shipping but we can help load it. all sales are final. As is, no returns(unless item is not received as described. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B2d71f%2B4g7%3E-144b85016fb-0xf6-
|
|
|
VINTAGE DELTA MILWAUKEE 14" DRILL PRESS BELT GUARD
This is the cast iron front guard and cast aluminum rear guard. The front badge has been wiped clean so no logo can be seen. There is a small clip to post work orders on mounted on the side of the rear guard. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*4a24%60%3C%3E-144bd3db597-0xfe-
|
|
|
Motor Mounting Bracket for Delta Drill Press
Motor mounting plate for Delta drill press. Fits the old Delta drill presses. dhep.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishm%3Ed%7Fhep-144be672f5c-0x109-
|
|
|
COPYRIGHT 1937 PRINTED 1947 DELTA BOOK FOR DRILL PRESS
This is a pretty nice Manual. 48 pages with over 200 Pics. Showing how to use the Delta Drill Press. The Cover hsa some dirt and there is a water stain in about 10 pages.
|
|
|
Delta 15" vs drill press adjustable handle and pinion.
Came off a Delta Rockwell 1964-65 15" Variable Speed VS-650 drill press. may fit other models. All teeth are there with very little signs of wear. to lower 48 states only. No international shipping.
|
|
|
DELTA DP600 17" DRILL PRESS SPINDLE MACHINERY
FROM DP 600 HEAD SHOWN IN PHOTO#2 MORSE TAPER VERY GOOD INSIDE TAPER AWAS CLEANED AND INSPECTED VERY FEW MINOR SMALL RADIAL LINES LOCKS EXCELLENT EXTERNAL RUST ON O.D. OF TAPER BODY WILL CLEAN UP WITH SOME EFFORT. INCLUDES SPLINED DRIVE SHAFT IN VERY GOOD CONDITION.670 DIA. REF FOR SPINDLE PULLEY NEEDS CLEANED UP. DID NOT DIS-ASSEMBLE INTERNAL BEARING- SPINS FREELY- NO SLOP BUT I WOULD AT LEAST CLEAN-UP OR REPLACE. REF. SPINDLE BODY 2 1/4 O.D. BY 9 3/8" LONG AND 3 1/2" LONG MORSE SHAFT. GOOD RACK- NO WEAR. NICE CLEAN O.D. ONE MARK(SEE PHOTO) RED ARROW FROM DEPTH STOP. COLLAR(NO HARM) UPPER BEARINGS WERE DISCARDED"DIRTY + RASPY" FOR SPLINE DRIVE)
|
|
|
Delta 17" Drill Press High Speed Pulley Set (Spindle & Motor) 725 & 826, 5 Speed
This is set of original Delta pulleys for the 17" drill press. These fit the older model drill press. These two pulleys were discovered at an estate sale and were in a box of Delta machine parts. Both of the pulleys are original Delta equipment and fit a specific range of machines. Please make sure these are what you want before you bid. The motor pulley is#725 and shows very little wear. The original Delta finish is still present on the inside of the pulley grooves. This pulley is 6 1/2 inches in diameter at the bottom and 2 3/4 inches at the top. The bore is 3/4 inches with a key way. The spindle pulley is#826 and has similar wear to the other pulley. Very minimal. This pulley is 6 1/2 inches at the bottom and 2 3/4 inches at the top. The bore is 17mm(which is correct according to my research) and it's also keyed. Each pulley has ... more5 speeds. They are in outstanding original condition and ready for your drill press or other application. These were designed as the high speed set for a 17 inch drill press and I believe they fit the earliest models. Again, make sure this set is what you are looking for as I am not a expert as to which machines they will work with. The belt in image#1 is included. Feel free to provide any information I may have omitted in the listing. I appreciate any input. Also ask questions if you have any. I will ship worldwide and will ship this set to the USA priority mail in the medium flat rate box. International bidders. This set weighs about 7 pounds packed and I ship to your preference. I always combine shipping to save you money and charge no extra fees to ship your item. You pay only the actual shipping costs! Please view my other listings for early American items. Axes, and saws. g.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bjw%60hquvg%3Eg-144f29a2bb7-0x107-
|
|
|
*DELTA* 17" Drill Press ~the Complete Head Raising Mechanism~ Rockwell
Here are all the parts you'll need to add a Head Raising Mechanism to your DELTA 17" Drill Press These parts come from a table mounted Delta 17" drill press. This is every single part you'll need. Right down to the tapered pins, and set screws. I inspected. Cleaned, and oiled everything. All these parts are in Very Good Working condition! It's very easy to install, and I'll be happy to answer any technical questions you have; regarding the installation. ~* ~ Let me know if you've got any questions. Thanks!
|
|
|
DELTA ROCKWELL 17 INCH DRILL PRESS COLLAR DP 204 2 3/4" COLUMN
Up for Sale is a Delta rockwell 17 inch drill press column table collar. fits 2 3/4" column. This item is in good usable condition. Big Daddys vintage tools is a small individually ran company located in Baldwinville Massachusetts. I mostly sell vintage machine parts but you will also find various other items. I am a part time seller and sell from a store rather than auctions. I find it easier to manage store selling than bulk auctions. Starting in June 2012 I will be dropped from some searches. So please if you like what I sell save me in your favorites. I can not offer one day shipping or 14 day free return shipping. I sell vintage machine parts and various other items purchased at auctions.Estate sales and yard sales. I do my best to tell the truth and honor my mistakes. There have been no items were I refused a full refund including ... morereturn shipping when I have made a mistake. I find most all buyers just want what they bought. But for what I sell I am going to continue with my policy of 5 days. That is please contact me if there is a problem within 5 days. I give some slack because if you get a item on a Monday you might not get a chance to really check it out until Saturday if your working. Please then contact me so we can resolve the issue. Shipping please read: Shipping is a necessary evil nobody likes to pay it. However it is necessary and for what I sell. I must charge shipping! I try to keep the cost down and do not charge a packaging fee. Some time back the host started charging a finale value fee on shipping. This means they collect a percentage of the shipping cost besides the standard item cost. On a smaller USPS Priority mail item the cost is really not effected, any difference I absorb as the seller. However on larger items shipped UPS Ground or trucking, I must add weight or adjust to reflect the percentage the host takes. For ex sample if I'm sending a 100 pound item from Massachusetts to Oregon via UPS Ground I would be paying 10 dollars towards shipping. Heavier trucked items the amoun
|
|
|
WALKER TURNER DRILL PRESS TABLE VINTAGE - DELTA
Walker Turner Drill Press table. I believe this is from a 15" drill press. The table measures 10" x 9-1/2" With a 7/8" diameter mounting whole in the back of the table.The table is in fair to poor condition, with two chips on both the right and the left sides of the table. Both chips are old, and don't seem to effect the tables performance at all.
|
|
|
excellent *DELTA* 17" Drill Press ~Slow Speed Spindle Pulley~ Rockwell Milwaukee
This is the Spindle Pulley from a DELTA 17" Drill Press It's the larger Slow Speed version The part No. is: DP-825 It's in Great Condition! ~* ~ Let me know if you've got any questions! Thanks!
|
|
|
Delta Heavy Duty Drill Press 16 1/2 2 MT Model 17-900
Delta Heavy Duty Drill Press 16 1/2" 2 Morse Taper Spindle with 5/8" Chuck. Used Very Little
|
|
|
Delta Rockwell 17-600 17" Drill Press, Variable Speed, 115V, 1-Phase
Delta Rockwell 17-600 17" Drill Press General Info: Stock# CB-141002-34 Machine Name:Delta Rockwell 17-600 17" Drill Press Condition: Used. Needs work Tested: Yes. Partial working condition Brand: Delta Rockwell Model: 17-600 Serial: 1399889 Year: N/A Shipping Weight: 750 Lbs. Shipping Dimensions: 48" L x 40" W x 68" H Location: Stone Mountain. GA Specifications: Delta Rockwell 17-600 17" Drill Press. 17" Swing. 3/4HP Motor, 115/230V, 1-Phase, Variable Speed Range from 230 to 2830 RPM, 14" x 11" Working Table surface, 6" Spindle Travel, 1/2" Jacobs Chuck, Cord& Plug. Additional Info: The Delta Rockwell 17-600 has been tested and has some issues. When the switch is turn on. The motor will want to start turning on its own, but requires a little push to get going. The variable speed ... moredoes not work. Other than those issues, unit is in good shape. Machine can be shown under power for inspection. Seller Contact Information: Mark Davis 404-272-1285 The Equipment Hub. LLC 1380-A Beverage Dr. Stone Mountain. GA 30083 It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week
|
|
|
*ATLAS* Drill Press~Head Raising Mechanism~* 2- 3/4" Column* Walker-Turner*Delta
ATLAS 15" Drill Press Head Raising Mechanism or{Head Positioning System} circa 1945) fits on. And will work with, any: 2- 3/4" column has 17" of vertical travel and a screw with: 3/4- 8 acme thread( 1/8" of vertical travel for every full turn) ~* ~ weight: 12 lb's total length: 23"approx. ~* ~ Thoroughly cleaned of all paint. Oil, and grease residue ~* ~ Moving parts. And inside castings lightly oiled. Gears lightly greased. ~* ~ WW-2 era quality well maintained never abused ~* ~ Top Working Condition Unconditionally Guaranteed! ~* ~~ Let me know if you've got questions! Item is available for inspection in Providence, For shipping. Item will be sent via UPS, and packaged with the utmost care. Thanks!
|
|
|
Vintage POWR KRAFT, made by Delta, 32" RADIAL ARM DRILL PRESS with stand
NICE old POWER KRAFT(Montgomery Wards) that was built by DELTA/ROCKWELL(confirmed by Delta/Rockwell web site) 32" RADIAL ARM DRILL PRESS. MODEL# TRT-2577, S/N 349 There is paint loss and rust but this thing is SWEET! The motor looks bad but is nice and quiet and strong! The drill press measures approx. 34 high. 31-3/4 deep with a base of 11-1/4 This comes with the stand(I think original. Can't confirm) that is heavy iron, approx. 30 x 16-1/4 wide x 31-3/4 high The Radial Arm Drill Press has a Jacobs Chuck that says 5/64- 1/2 capacity. Original key All the handles/levers work great and you could start work as soon as you get it. Or restore it to it's former glory! This is HEAVY and for local pick-up only in Gilbert. AZ.please bring help with loading! Please review the pictures as they are part of the description. If you like VINTAGE ... moreequipment- made to last. This one is for you! Please ask any questions. I'll do my best to answer them! Thank you for shopping at Sandie's Little Bit a little bit of everything.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-1454cef0bdd-0x112-
|
|
|
Delta SHOPMASTER 16-1/2" Floor Model Drill Press (Model DP400)
PICK UP ONLY. Southeast corner of 695 in Baltimore(Watersedge. Dundalk) Personal use only. Used very little and in good working condition.
|
|
|
DELTA/MILWAUKEE HOMECRAFT 11-120 11" VINTAGE DRILL PRESS, 1/4HP, 115V,
This Delta/Milwaukee Homecraft Drill Press is in great condition for its age. Has been inspected. Tested, and works with no problems. Manufactured probably between 1940-1952. This press is very clean for its age. Motor is a GE 1/4 HP, 1725 rmp, and operates at 115v 60Hz. Is mounted on a homemade stand but is sturdy. On/off switch as been replaced with a new cord. If you have any questions please message me for a prompt reply, or call me at 919 215 3886. This press is available for local pick-up or can be shipped at your expense. Please call to make arrangements prior to purchasing please. A good article that tells all about this press can be found at. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28e013%3F%3E%3A-14551b31cca-0x106-
|
|
|
Delta drill press 8 inch Model 11-950
Delta Bench Drill Press 8" Model 11-950. 1/4 Horse Power RPM 1720 2.5 Amps I think this is a good drill press. You can't get these now i don't think. o OK with the shipping. I can help with shipping. if you think that it is too much I'll pitch in. I'll send money to you via papal. Shipping is rediculous. I want everyone in the country to get about the same charge. No descrimination on where you live. As long as its in the USA. I will be very reasonable. Go Army!
|
|
|
DELTA ROCKWELL 14" - 15" DRILL PRESS MANUAL FOOT FEED ARM / BRACKET
Delta Rockwell arm for the manual food feed set up. I don't have any other parts for the system just the arm pictured. The arm is in good shape. 2-3/4" ID Bore. Returns accepted. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf%60%60%3E-1456935ee9b-0x10c-
|
|
|
Delta DP-250 Drill Press Variable speed Stop rod assembly and collar
Collar and stop rod assembly for a Delta DP-250 Variable speed drill press. You will receive exactly as pictured.
|
|
|
Delta DP-250 drill press Quill Spindle and chuck assembly Variable speed
Good used Quill. Spindle and Chuck assembly from a Delta DP-250 drill press in good usable condition. All are used. You will receive exactly as pictured.
|
|
|
Delta DP-250 drill press Power switch and cover Delta part# 904121
I have a power switch assembly for a Delta DP-250 Variable speed drill press. Good usable condition delta part# 904121
|
|
|
Delta DP-250 Drill Press Pinion assembly Part# 904152 Variable speed
I have good used Pinion Assembly for a Delta DP-250 Variable speed drill press. Delta part# 904152
|
|
|
Delta DP-250 drill press Quill Return Spring Assembly housing Part# 1310082
Delta DP-250 Quill return Spring in good usable condition. Delta part# 1310082. I do not know what other applications or machines this may or may not work with. 2p5ddv.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2B26rk%3E2p5ddv-1456935eef4-0x10d-
|
|
|
Delta drill press DP-250 Replacement Motor 1/3HP PN# 906785 May Fit others?
I have a good used Delta Motor from a DP-250 Variable speed drill press. I was using this press up till a few weeks ago but the Reaves Pulley disintegrated and I decided to get a new press. The Delta part number 906785. I do not know what if any other drill presses or machines it may or may not work with. Research and cross reference with the Delta number.
|
|
|
Vintage Delta Rockwell Drill Press Return Spring Assembly 15" or DP225 14"
Up for auction is a Vintage Delta Rockwell Drill Press Return Spring Assembly 15" or DP225 14" It comes as pictured. Please review pics attached. Good luck bidding.
|
|
|
Delta DP-250 Drill Press Belt Pulley guard housing shield # 906787
I have a belt guard from a Delta DP-250 Drill press it is in good condition but there is a minor bend on one side. I could not get it to show in a pic. Delta# 906787
|
|
|
Delta DP-250 Drill Press Instruction manual Original Shopmaster
Original Delta Shopmaster Instruction Manual for DP-250 Drill Press. Not a copy, also complete and good condition.
|
|
|
Delta DP-250 Drill Press Variable speed cast iron base # 1343751
I have a cast iron Base from a Delta DP-250 Drill press in good used condition. Delta part# 1343751
|
|
|
Delta DP-250 Drill Press Variable speed Adjusting cam Hub Knobs parts ASSEMBLY
I have for a Delta DP-250 Variable Speed Drill Press. The speed adjustment cam, hub and levers. There is no key stock included with it. dhep.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishm%3Ed%7Fhep-1456de5a392-0x112-
|
|
|
Delta DP-250 Drill Press Column Base Parts Variable speed
I have a column mount that attaches to the base of a Delta DP-250 Drill press in good used condition.
|
|
|
Delta DP-250 drill press parts pulley spring cap washer # 904162, 904161,
I have the spring. Cap and pulley washer from a Delta DP-250 Drill press in good used condition. di,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishhov%3C%3Edi-1456de5a3bc-0x105-
|
|
|
Vintage Belt Pulley Guard 4-step Delta Rockwell Drill Press mdl 220 Milwaukee
From a Delta Rockwell DP220 floor model drill press. No cracks or chips. And it has its three original attachment screws/bolts. a;06d2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28%3Ea%3B06d2-14582b795ca-0x10a-
|
|
|
Delta Rockwell Model: UA 66E320W Drill Press - 3 Phase.
InterSchola is retained by education institutions and local public agencies nationwide to bring valuable surplus inventory to the eBay marketplace. Items listed by InterSchola have been declared surplus by the appropriate education or public agency institution in accordance with state regulations regarding the sale of surplus assets and are listed for sale as a service to these organizations. Net proceeds from the sale of these items are returned to the school districts or local public agencies to support their budgets. See our page to learn more about InterSchola. Please also visit the InterSchola Store to see other assets for sale! Delta Rockwell Model: UA 66E320W Drill Press- 3 Phase. Item Description: This is a Delta Rockwell Drill Press Model: UA 66E320W Serial# 119-4077 Measures 20" x 27" x 37" Phase 3. 1/2 horsepower, ... moreVolts: 208/220/440 The items in this auction were not tested at inspection. Their operational status is unknown. NOTES: Buyer will be responsible for all equipment. Tools, personnel and transportation necessary for loading and removal from site. Please utilize our scheduled inspection time to view the item(s) first hand and up close. Please check the location of this listing. Many of our item(s) are for local pick up only. This listing is located in Daly City. CA, 94015 Item(s) are Sold As-Is. to view our current offerings of school district/public agency surplus items we have for sale on eBay. Click images for larger view(ISID: 39463) nbsp, nbsp, Model: Delta Rockwell , nbsp, Accessories: Only the accessories or parts described in this listing are included with this item. No other accessories. Including other items or accessories that may be pictured, are guaranteed to be included. nbsp, nbsp, Condition: This item is used and sold as-is. Due to the location. This item was NOT TESTED for operation. Item may need service and/or parts to make operational. nbsp, nbsp, Pickup Logistics and Handling: Forklift and loading dock may be available on site to assist in loading
|
|
|
Delta Drill Press 8 Inch Model 11-950 Type 2
Delta Drill Press 8 Inch Model 11-950 Type 2 Used works great now. Belt is still working but may need one soon Sell exactly as seen on picture No other accessories included thats not picture No return accepted di,RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishhov%3C%3Edi-145998f76fd-0x10d-
|
|
|
DELTA RAM RADIAL DRILL PRESS 15" INDUSTRIAL 15-127
DELTA INDUSTRIAL RADIAL DRILL PRESS CAT. NO. 15-127 PRESS WAS REMOVED FROM A WORKING ENVIROMENT. BUT WE HAVE NOT TESTED SO IT IS BEING SOLD AS IS AND ALL SALES ARE FINAL. BUYER IS RESPONSIBLE FOR ARRANGING FREIGHT AND PROVIDING AFS WITH PICKUP DATE AS WELL AS EMAILING OR FAXING(210-658-2244) A COPY OF THE BILL OF LADING AT LEAST 2 DAYS BEFORE PICKUP IS SCHEDULED. FORKLIFT IS AVAILABLE FOR LOAD OUT. A PALLETIZING FEE OF $40 WILL BE ADDED TO TOTAL INVOICE IF ITEM IS BEING FREIGHTED. THIS FEE INCLUDES BANDING ITEM TO SKID. THE INFO NEEDED TO GET A QUOTE FOR FREIGHT WILL INCLUDE THE ZIPCODE 78108. THE WEIGHT APPROX. 700 LBS. AND PALLET DIMENSIONS 48"X48"X48" ITEMS WILL BE CONSIDERED ABANDONED IF THEY ARE NOT PICKED UP WITHIN 30 DAYS OF AUCTION ENDING. Disclaimer- ALL ITEMS NEW OR USED ARE SOLD AS IS AND ALL SALES ARE FINAL. QUESTIONS? ... morePLEASE CALL 210-566-3300 or text us at 210-273-3394 Check out my other items! Be sure to add me to your favorites list! 2p5ddv.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2B26rk%3E2p5ddv-145ab847a5b-0x114-
|
|
|
Old Style Delta 14" Drill Press Accessory Spindle
Old Style Delta 14" Drill Press Accessory Spindle. For buffing wheels, etc. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press #1 Morse Taper Spindle
Old Style Delta 14" Drill Press#1 Morse Taper Spindle. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press 5/16" Shaper Spindle
Old Style Delta 14" Drill Press 5/16" shaper cutter Spindle. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Very nice *DELTA* 17" Drill Press~ Pulley Set (Slo-Speed) ~ Rockwell
This Pulley Set is for a DELTA 17" Drill Press This Set has the larger, Slo-Speed version of the Spindle Pulley(part# DP-825) The matching Motor Pulley has part# DP-645) Both of these pulleys are in Excellent condition. I couldn't find any cracks. Breaks, or signs of significant wear. Altogether. A really Nice Set! ~*~ ~Pulleys will be very well packaged for shipment.~ ~* ~ Let me know. If you've got questions. Thanks!
|
|
|
Delta Drill Press Depth Gage
This Depth Gage is in fine working condition. The broaching or lines on the jamb nuts are worn. This very heavy duty Depth Gage is in serviceable condition ready to be bolted up to your 17 inch or greater drill press. It could be used on a 15inch unit if the threaded rod were shortened by one inch. The winner of the auction will have the tool shipped in a USPS Small Flat Rate box for $5.35 in the 48 contiguous States. All other places will require additional postage.
|
|
|
delta drill press dp220 slo speed attachment 1028/1029 Very RARE
MUST BE USED WITH FOOT FEED BRACKET DP439. Or make a sleeve for it like atlas 1060 has. See Vintage Machinery. org for more information.Column cam diameters are 2.250 and 2.660. Thank you
|
|
|
Vintage Drill Press Pulley. Delta, Craftsman, Rockwell, Homecraft, Milwaukee ??
Description" This has blue paint leading me to believe that it could be a dual. Or double pulley from a Dunlap or Craftsman drill press or lathe. But I've used other key words for your search terms in hopes you can identify it as the piece you need. Could be a lawnmower part for all I know but it looks to important to just chuck out. Important" Please wait to be invoiced if you purchase multiple items if you want shipping combined. And please c heck out my other auctions if ya have a moment! thanks for the visit.Tom. Shipping& Combined Shipping& Payment" Sorry. No international shipping. I only ship within the contiguous united states, Alaska& Hawaii. I combine shipping when sensible and applicable. Auction style has a two day grace period for payment else settings default to a nudge in which if ignored will ... morecancel auction after four days. Standard procedure please don't personalize it. Shipping is on the same day or the fallowing business day. I package with recycled materials and this saves us money. And usually my packaging will withstand a tumble down a mountainside when applicable. I've never had an item break in transit and that reflects in my rating. Also, These estate items will at times arrive with the scent of the previous owners surroundings so I will at times add pleasant fragrances. Philosophy" I hold myself accountable with making you comfortable with your purchase. I don't fluff things up with misleading information and I don't hide imperfections. I figure if you like the item then you have the sense to make an informed decision based on an honest description. I earned my 100% reputation through good communication and quality control. I strongly believe in old school business ethics and prefer a satisfied customer over the long term rather than the short term buck. So if you are ever unhappy with a purchase. Then I will refund your money without a problem. Feedback" As a seller. It's no inconvenience to me to leave you positive feedback a
|
|
|
HEAVY DUTY ROCKWELL DELTA DRILL PRESS VARIABLE SPEED
ROCKWELL DRILL PRESS JACOBS DRILL CHUCK 1/2' CAP HEAVY DUTY TABLE WITH VISE TABLE SIZE- 11 BY 14' 230/460- 3 PHASE CAME OUT OF A WORKING SHOP- I USED IT BUYER CAN ARRANGE SHIPPING I WILL BAND TO A PALLET AND LOAD
|
|
|
Delta DP220 14" Vintage Drill Press, 1/3 HP, 115V, 1PH
Delta Approx. 15" Swing Vintage drill press, Cleaned and checked, Model DP 220, 1/3 HP motor. 115V, 1PH, 1750 RPM, Stock Number: B-1-110(w) Framing or crating will incur additional charges. If needed Please Email or call 1-800-793-4494 if interested in this machine. Many other new and used machines are stored in our warehouse and can be viewed. Shipping& Freight: Purchaser/Buyer/Winning Bidder pays all shipping/freight costs associated with getting this machine to your location if item is to be shipped and not picked up in person. DELIVERY: Varies upon warehouse workload and potentially the item. This item may be released immediately by the warehouse. But sometimes up to 7 business days are needed to prep and release said item. Subject to Prior Sale. This item may be withdrawn from sale at any time as it is listed on our website ... moreand in other advertising. PAYMENT TERMS: Full Payment or deposit required within 24 hours of order. NO EXCEPTIONS. Items not paid for or held via deposit after 7 days will immediately be reported to eBay as unpaid! Cash in person, M.O. Personal/Company Check or Visa/Mastercard/Discover accepted. Wisconsin Sales and Use tax of 5% required for all purchases by Wisconsin residents who do not have a tax ID or are not able to fill out an exemption claiming the machine for business/manufacturing use. Minimum $125.00 Crating Fee. If required. Used equipment is sold as is. Where is, unless otherwise specified. SELLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Freight. Rigging, and installation are not included unless otherwise specified, but arrangements can be made at an additional cost. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-14663017b11-0x135-
|
|
|
Delta drill press, head clamping assembly
Clamp assembly for delta drill press. 1" diameter X 6-1/2 over all length(not including handle) Great condition. Works as it should. No rust 336.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E336-146a5883e0a-0x111-
|
|
|
Delta 16 1/2" Drill Press Reduced PRICE
Delta 16 ½” Drill Press ¾ Horse Delta International Machining Corp. USA Product Description: Condition: Used. In great working and overall condition, one owner and only used as a back-up drill press with very little time on it. Belts are in great condition. Unit is very clean and well taken care of. Includes chuck. Please refer to pictures Model No: 17-900 Serial# 8925 RPM: 1720 Motor: 3/4h Motor# 1312023 Phase: 1 Volts: 115/230v. 60hz Amps: 12/6 Shipping Information: Due to size and weight freight shipping or local pickup only*Contact for Freight Estimates Approximate Dimensions: Height: 70" x Width: 16" x Depth: 32" Approximate Shipping Weight: Approx. 120lbs Contact use directly for any shipping or other questions. Contact Information: Nathan Phone: 860)818-5259*More photos and information can be provided if requested(remit ... moreto the above contact information) Unit includes ONLY what is shown in picture(s) above unless otherwise noted.
|
|
|
Delta Shop Master Drill Press 10", 1/4 HP, 110V
1/4 HP. 110 V. H 14" W 10" L 29" SN 107586W4071.
|
|