|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Free Shipping Condition: New Location: United States Function： It can use with annular cutters and solid drill bits. These solid twist drill bits can be used for smaller holes drilling applications. Material： ... moreIt can drill holes in steel or stainless steel with an accuracy of 0.001 mm to 0.005 mm.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Woodworking Hole Drill Bit Mortise Locator Tenoning Machine for Bench Drilling Specification: Material：steel Applicable machine tools: drilling machine ... moreSize: approx 45*35*20cm Note: 1. This product is used with a bench drill. 2. This product has size requirements for the bench drill used. 3. This product has a requirement for the distance between the drill chuck and the table when in use. 4. The diameter of the clamping part of the square hole drill used in this product is also required. Packing including： 1* Locator Set (excluding bench drill).
Buy It Now
Free Shipping Condition: New Location: Nixa, United States This manual has information on motor speeds as well as a diagram of the bearing setup on the spindle/quill. This manual covers many drill press models. ... moreThe following a few of the known model numbers covered in this drill press manual: 989, 999, 1289, 1300, 1302, 14-005, 14-006, 14-007, 14-008, 14-205, 14-206, 14-207, 14-208, 14-210, 14-211, 14-212, 14-213.
Buy It Now
$16.50 Shipping Condition: Used Location: Landenberg, United States The white oilstone is NEW.NOS.with a few stains. 3" Palmgren Drill Press Vise. Several nice chuck keys.New.NOS. Plenty of high resolution pictures are ... morefeatured.
Buy It Now
Free Shipping Condition: New – Open box Location: Goddard, United States The manual has about 20 pages. Delta 14" Drill Press. About this manual : This is a high quality reproduction manual which has been scanned with a high ... moreresolution scanner. Type of Manual:Instruction & Parts List.
Buy It Now
Free Shipping Condition: New Location: Alhambra, United States 4 in 1 Key. Fits popular small size chucks.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Specifications: Rated power: 480W Rated current: 0.55A Table size: 17*21.5cm The spindle is about 110MM away from the drill bit center Drilling diameter: ... more1-10mm Max Spindle travle: 40mm NO-load speed： I: 0-5000r/min II:0-11000r/min Drill capacity: Woods:φ25mm Iron：φ7mm Features: -Suitable for drilling, expanding, and reaming operations on metals and other materials. It can be widely used in single-piece or mass-produced instrument industry, machinery manufacturing and repair parts. -High-power 480W miniature portable bench drill Precision drilling machine motor copper -The motor has increased power, which is to increase the life of the motor.
Buy It Now
Free Shipping Condition: New Location: Alhambra, United States 4-in-1 Chuck Key Features: Convenient and Extra Strong Suitable for Most Chucks Sizes: 1/2" 9/16" 5/8" and 11/16" Includes: 1pc 4-in-1 ... moreChuck Key Packaging: Brand New Product with Retail Packaging
Buy It Now
Free Shipping Condition: New Location: Long Beach, United States Motor 100W. Spindle Stroke 1". Chuck Size: 1/4". No Load Speed 0 to 2000rpm. Table Size 170 x 170 mm. If you feel our S&H prices are too high, we can ... moreprovide you weight the item's weight so that you can confirm the prices for yourself.
Buy It Now
Free Shipping Condition: New Location: Vancouver, United States Brand New! For those that prefer traditional keyed drill chucks. These chucks offer precision and nearly unlimited mechanical advantage for tightening ... moreand loosening drill bits and tooling. These 1/32" 5/8" JT33 Taper drill chucks have fluted grips and the chuck key is included. Specifications: 1/32" 5/8" JT33 Fluted Grips Chuck Key Included ITEM D3455 Payment: You may pay instantly with PayPal by clicking the pay now button at the top. Return Policy 100% Satisfaction Guaranteed 100% Money back Guaranteed All product exchanges must be in 100% brand new condition Please contact us within 7 days upon damaged item is received We will file claim for all buyers on damaged or lost items Exchange. Refund, or replacement will be offered upon buyers request Please contact us for more information by using"ask a question" link at the bottom of the listing Customer satisfaction is our primary goal and we will resolve any problems such as damaged. Not as described, missing parts, and lost items. Please contact us before leaving a negative or neutral feedback. Our office hours are Monday to Friday 8:00am-6pm PST. All emails will be replied within 24 hours except Sat. Sun. and US holidays. Thank you for visiting our store! Terms: Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. Colors or packaging of items delivered may vary from those photographed Payment is expected within 7 days of auction close. We cannot guarantee availability of product if we do not receive payment within 7 days. Shipping: Free shipping to the all of USA unless otherwise stated. Shipping discounts for multiple items will be done on a case by case basis for international buyers. WE SHIP FASTER and SAFER THAN MOST SELLERS JUST CHECK OUT OUR FEEDBACK! We stock all available items. And we ship from our warehouse. Orders are shipped the same or next business day after payment received. We ship with Fedex ground or with the US Postal Service
Buy It Now
Free Shipping Condition: New Location: Vancouver, United States D3457 Keyless Drill Chuck 1/2" x JT33 Description: These Keyless Drill Chucks provide extreme accuracy. Reliability and ease of use. Large knurled ... moregrips allow plenty of tightening torque for no-slip operation. Precision made components make these drill chucks a pleasure to use. These 0" 1/2" JT33 Taper drill chucks have large knurled grips allowing plenty of torque for no-slip operation. Specifications: 0" 1/2" JT33 Keyless Knurled Grips SHIPS SAME DAY IF PAID FOR BY 4PM PST Payment: We prefer You may pay instantly with PayPal by clicking the pay now button at the top. Return Policy: NO QUESTIONS ASKED! You may return the product within 30 days of receipt. Item must be returned in new condition. As received with all accompanied accessories and literature, including the factory carton. Shipping, handling is not refundable unless item is returned because of defect. If item is found defective return shipping will be refunded to the buyers paypal account once the item is verified defective. Buyer is responsible for return shipping costs and logistics for all returned items that are not defective. You must contact us within 30 days of receipt, to request an RMA number. Items received without an RMA number, will be refused and returned to the sender. Terms: Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. Colors or packaging of items delivered may vary from those photographed Payment is expected within 7 days of auction close. We cannot guarantee availability of product if we do not receive payment within 7 days. Shipping: Free shipping to the all of USA unless otherwise stated. Shipping discounts for multiple items will be done on a case by case basis for international buyers. WE SHIP FASTER and SAFER THAN MOST SELLERS JUST CHECK OUT OUR FEEDBACK! We stock all available items. And we ship from our warehouse. Most orders are shipped the same or next business day after payment received. We ship with Fede
Buy It Now
Free Shipping Condition: New Location: Long Beach, United States 5 Speed Bench Drill Press Top Bench Mini Drill Press 1/2" Chuck Motor 1/2 HP Chuck Size: 1/2" Table Tilts From 0-45 Degree Quick Belt Tension ... moreRelease for Easy Speed Changes 1/2HP Motor 120v 60Hz No Load Speed 580 to 2650 rpm Spindle Stroke 2" Max Swing 9-1/2" FREE SHIPPING TO THE LOWER 48 STATES PAYPAL VERIFIED AS OF 2002 We only accept PayPal. If paying with PayPal please wait for your payment information to update. DO NOT CLICK'PAYMENT SENT' if you are paying with PayPal. This makes it difficult to find your payment information and will delay shipping time. Most items are eligible for a shipping combination. These items must be paid for together. And recieve a 20% discount off total shipping costs. Please wait to receive your combined invoice, do not go through checkout until your combined invoice has been sent! Please note that it is the buyer's responsibility to maintain their shipping address updated. Items will be shipped to the address registered as the shipping address with Ebay/and-or/Paypal at the time of payment. Any updates to the shipping address must be made prior to payment. WE DO NOT ALLOW PICKUPS. NO PICKUPS. NO EXCEPTIONS. We do not ship to unregistered addresses. Your address must be registered with both Ebay and Paypal. We DO offer shipping to PO Boxes. However all shipments to PO Boxes must be made through USPS. If you require shipping to a PO Box you must pay using the USPS shipping option. It is the buyer's responsibiity to receive the package. Or pick it up from the carrier's location. If a package is returned to us because the Buyer failed to pick it up, or receive it then they will be issued a refund for the Purchase Price of the item, not including Shipping And Handling Costs and minus both a 15% restocking fee and return shipping costs. Most of our shipments take place 1 business day after payment is received. Domestic shipments can take from between 1-3 Business days to process. International Shipments can take from 3-5 Business days to process.
Buy It Now
$26.06 Shipping Condition: Used Location: Waterford, United States USED, DELTA MILWAUKEE DRILL PRESS TABLE. THE INDEX PIN IS MISSING. NO CRACKS OR REPAIRS. THE COLUMN BORE IS 2-3/4". THERE ARE DIVOTS, SCUFFS, SCRATCHES ... moreAND WEAR FROM USE. NO EXCEPTIONS; NO MATTER HOW CLOSE YOU THINK YOU LIVE TO MY LOCATION.
Buy It Now
Free Shipping Condition: New Location: Perth Amboy, United States Why Choose VEVOR?. VEVOR MD50 Magnetic Drill Press 1HSS Cutter Set Annular Cutter Kit Mag Drill. VEVOR HSS Annular Cutter Magnetic Drill Set 6 PCS 3/4" ... moreWeldon Shank 2" in Depth. VEVOR Magnetic Drill 1300W 2922lbf/13000N Portable Mag Drill Press 810RPM.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Handle Base Parts Tools &195mm Handle Bar Set For CNC Drill Press Machine Parts. Applicable bench drill models: Z512-2, Z516, Z512B, Z516B, Z4116, Z4120, ... moreZ4120, Z4125, Z512-2D, Z516-2D, Z512D, Z516D, Z4120D, Z4125D, Z4120B1, Z4125B1, ZX7025, etc.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Floor Drill Press Stand Table for Drill Workbench Repair Tool Clamp for Drilling Collet,drill Press Table. It can be put or fixed on the workbench, and ... morehold the electric drill firmly to ease your fatigue and add a whole new level of accuracy.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Specifications: Rated power: 480W Rated current: 0.55A Table size: 17*21.5cm The spindle is about 110MM away from the drill bit center Drilling diameter: ... more1-10mm Max Spindle travle: 40mm NO-load speed： I: 0-5000r/min II:0-11000r/min Drill capacity: Woods:φ25mm Iron：φ7mm Features: -Suitable for drilling, expanding, and reaming operations on metals and other materials. It can be widely used in single-piece or mass-produced instrument industry, machinery manufacturing and repair parts. -High-power 480W miniature portable bench drill Precision drilling machine motor copper -The motor has increased power, which is to increase the life of the motor.
Buy It Now
$28.27 Shipping Condition: Used Location: Waterford, United States USED, CAST BELT GUARD FOR THE SLO SPEED (BIG PULLEY) DELTA 14" DRILL PRESS WITH THE DP220 HEAD CASTING. THE MOUNT BRACKET HAS A CHIP OUT OF IT. IT STILL ... moreHOLDS ONTO THE FRONT PULLEY COVER. THERE ARE NO CRACKS OR REPAIRS ON THE BELT COVER SECTION.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Specifications: Rated power: 480W Rated current: 0.55A Table size: 17*21.5cm The spindle is about 110MM away from the drill bit center Drilling diameter: ... more1-10mm Max Spindle travle: 40mm NO-load speed： I: 0-5000r/min II:0-11000r/min Drill capacity: Woods:φ25mm Iron：φ7mm Features: -Suitable for drilling, expanding, and reaming operations on metals and other materials. It can be widely used in single-piece or mass-produced instrument industry, machinery manufacturing and repair parts. -High-power 480W miniature portable bench drill Precision drilling machine motor copper -The motor has increased power, which is to increase the life of the motor.
Buy It Now
Free Shipping Condition: New Location: Vancouver, United States D3458 Keyless Drill Chuck 5/8" x JT6 Description: These Keyless Drill Chucks provide extreme accuracy. Reliability and ease of use. Large knurled ... moregrips allow plenty of tightening torque for no-slip operation. Precision made components make these drill chucks a pleasure to use. These 1/32" 5/8" JT6 Taper drill chucks have large knurled grips allowing plenty of torque for no-slip operation. Specifications: 1/32" 5/8" JT6 Keyless Knurled Grips SHIPS SAME DAY IF PAID FOR BY 4PM PST Payment: We prefer You may pay instantly with PayPal by clicking the pay now button at the top. Return Policy: NO QUESTIONS ASKED! You may return the product within 30 days of receipt. Item must be returned in new condition. As received with all accompanied accessories and literature, including the factory carton. Shipping, handling is not refundable unless item is returned because of defect. If item is found defective return shipping will be refunded to the buyers paypal account once the item is verified defective. Buyer is responsible for return shipping costs and logistics for all returned items that are not defective. You must contact us within 30 days of receipt, to request an RMA number. Items received without an RMA number, will be refused and returned to the sender. Terms: Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. Colors or packaging of items delivered may vary from those photographed Payment is expected within 7 days of auction close. We cannot guarantee availability of product if we do not receive payment within 7 days. Shipping: Free shipping to the all of USA unless otherwise stated. Shipping discounts for multiple items will be done on a case by case basis for international buyers. WE SHIP FASTER and SAFER THAN MOST SELLERS JUST CHECK OUT OUR FEEDBACK! We stock all available items. And we ship from our warehouse. Most orders are shipped the same or next business day after payment received. We ship with F
Buy It Now
Free Shipping Condition: New Location: La Center, United States 1/32" - 5/8" B16 Taper Drill Chuck. Chuck Key Included.
Buy It Now
Free Shipping Condition: New Location: Vancouver, United States D3458 Keyless Drill Chuck 5/8" x JT6 Description: These Keyless Drill Chucks provide extreme accuracy. Reliability and ease of use. Large knurled ... moregrips allow plenty of tightening torque for no-slip operation. Precision made components make these drill chucks a pleasure to use. These 1/32" 5/8" JT6 Taper drill chucks have large knurled grips allowing plenty of torque for no-slip operation. Specifications: 1/32" 5/8" JT6 Keyless Knurled Grips SHIPS SAME DAY IF PAID FOR BY 4PM PST Payment: We prefer You may pay instantly with PayPal by clicking the pay now button at the top. Return Policy: NO QUESTIONS ASKED! You may return the product within 30 days of receipt. Item must be returned in new condition. As received with all accompanied accessories and literature, including the factory carton. Shipping, handling is not refundable unless item is returned because of defect. If item is found defective return shipping will be refunded to the buyers paypal account once the item is verified defective. Buyer is responsible for return shipping costs and logistics for all returned items that are not defective. You must contact us within 30 days of receipt, to request an RMA number. Items received without an RMA number, will be refused and returned to the sender. Terms: Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. Colors or packaging of items delivered may vary from those photographed Payment is expected within 7 days of auction close. We cannot guarantee availability of product if we do not receive payment within 7 days. Shipping: Free shipping to the all of USA unless otherwise stated. Shipping discounts for multiple items will be done on a case by case basis for international buyers. WE SHIP FASTER and SAFER THAN MOST SELLERS JUST CHECK OUT OUR FEEDBACK! We stock all available items. And we ship from our warehouse. Most orders are shipped the same or next business day after payment received. We ship with F
Buy It Now
Free Shipping Condition: New Location: Jacksonville, United States Here are the details Crank made from cast iron with PVC cushion revolving grip. A rugged & durable alternative to aluminum and plastic crank handles. ... moreRugged handle with cushion grip for raising & lowering drill press table.
Buy It Now
Free Shipping Condition: New Location: Ontario, United States 14 in Heavy Duty Floor Drill press - G7944. Volts 120V. Swing 14 in. Table and Base are Cast Iron. Table Swing 360 degrees. Drill Chuck 3/64 in - 5/8 ... morein. Precision Ground Cast Iron Table Yes. Number of Speeds 12 (140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 RPM).
Buy It Now
Condition: Used Location: Coffeyville, United States MODEL: 5Z146. 14" BENCHTOP. DRILL PRESS. 24 1/2" X 12 1/2" X 40". AMB.: 40 DEGREES CELCIUS. DATE CODE: D90 7. NO: S63HYA-7000. BRG: SLEEVE.
Buy It Now
Condition: Used Location: Lexington, United States As you can see from the pictures, it's very lightly used and is in excellent condition. The precision-ground cast-iron table is 11-3/8" by 11-3/8 and ... moretilts 90° left and right. It swivels 360° around the steel column and has four 5/8" T-slots, 3-7/8" on center.
Buy It Now
$12.65 Shipping Condition: Used Location: Nashville, United States As shown, in good used condition, for 2-3/4" o.d. column drill presses.
Buy It Now
Free Shipping Condition: New Location: Bellingham, United States Spring/ Summer Sale! Regular Price: $385.00 Sale Price: $355.00 This is a brand new machine in factory packaging with a 1 year warranty! This machine ... moreships via a common carrier. Buyer is responsible for making arrangements to accept delivery. See below for details. G7944 12 Speed Heavy-Duty 14" Floor Drill Press This heavy-duty floor model drill press is the mainstay in any shop with 12 speeds and powerful 3/4 HP motor. A very popular machine! Specifications: Motor: 3/4 H.P. Single-phase, 110V Overall height: 64" Spindle travel: 3-1/4" Number of speeds: 12 Drill chuck: 1/8"5/8" Spindle taper: MT#2 Range of speeds: 140. 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 RPM Swing: 14" Drilling capacity: 3/4" steel Table: Precision ground cast iron Table size: 11-3/8" sq. Table swing: 360° Table tilts: 90° in both directions Approx. shipping weight: 172 lbs. To view the manual for this item. Please click on the link below: http:cdn2.grizzly.com/manuals/g7944_m.pdf Item Location: Bellingham. WA/ Springfield, MO/ Muncy, PA How Quickly Do You Ship Orders? Orders received before 12 noon(Eastern time) Monday through Friday, are normally shipped the same day. Once shipped, orders take approximately three to five business days to arrive. How Are Items Shipped? Items under 70 lbs. are shipped via UPS Ground. Items over 70 lbs. are shipped via truck freight. The trucking company will call you to arrange for curbside delivery. Your delivery address must be accessible by tractor-trailer. Liftgate Service Truck drivers are subject to a number of regulations. One of which is that they are not required to assist with unloading. Freight deliveries are made at curbside, and your merchandise is moved to the back of the truck. You are responsible for unloading. With our optional liftgate service. Your merchandise will be moved to ground level at curbside. Please be prepared to move the item and place it in your shop. Liftgate service is available for an additional $34.00 char
Buy It Now
$4.00 Shipping Condition: New Location: Chino, United States Specifications Color: Black Style: Modern Shank Type: Round Tool Flute Type: Straight Assembly Required: Yes Material: Gray Iron, 45# Steel, High-carbon ... moreSteel, Plastic, etc Process: Heat Treatment, CNC Machining Max. Height of the Board: 10cm/4inch Max. Width of the Board: 6.5cm/2.5inch Positioning Fixing Hole Diameter: 19mm/ 3/4inch Applicable Drill Presses: 60mm/2.36inch, 58mm/2.28inch, 55mm/2.16inch, and 52.5mm/2.06inch Tenon Drills: 6.35mm/ 1/4inch, 15.8mm/ 5/8inch, 9.5mm/ 3/8inch, and 12.7mm/ 1/2inch Product Size: 35.5*12*28.5cm/13.98*4.72*11.22inch Package Size: 28*35*13cm/11.02*13.78*5.12inch Net Weight: 5.2kg/11.46 lbs Gross Weight: 4.5kg/9/9 lbs Package Included 1* Support Base 1* Fixed Seat 1* Locator 1* Press Block 2* Fixing Bolts 1* Connecting Rod 1*.
Buy It Now
Free Shipping Condition: New Location: United States | | | | Wilton 12800 Drill Press Vise. 2-1/2" Jaw, 1-1/2" Depth. International Customers: All electronic products are packaged for sale in the ... moreUS with US voltage. This item is brand-new. Factory sealed. features and benefits: precision grinding of sides and front side face, cross-patterned 90 degree v-groove stationary jaw with moveable jaw plate, versatile, stationary, recommended for general use, this versatile stationary drill press vise features precision grinding permitting additional mounting positions for your workpiece when drilling. Tapping or reaming. We only accept Paypal. Most orders placed prior to 11AM PST ship same business day. Some lightweight items ship Postal and can be shipped to a PO BOX. Most other orders will ship via UPS or FedEx. Please note we cannot ship UPS or FedEx to PO Box addresses. Expedited orders will ship 2nd Day Air. This item is eligible for return within 30 days of delivery. Returns of non-defective items will be charged a 15% restocking fee. Please visit our Returns Page for more information on Excluded Items. Damage Claims, and more details on requesting RA information. Founded in August 2002. Beach Audio´s mission is to provide the best experience on the Internet for buying Consumer Electronics. We focus on making purchasing online a pleasant experience. We offer flat rate Ground shipping on all items less than 75 pounds that can be shipped via common carrier. Our sales office is located in beautiful town of Redondo Beach, California, just a few miles South of Los Angeles International Airport. We do not stock any inventory at our sales office. Instead, we ship from several warehouses located throughout the country. Our sophisticated fulfillment system will automatically ship from the warehouse location that is closest to your shipping address! Why are our prices so low? It´s simple. We have modeled our business much like a wholesaler. We sell in huge volume and have streamlined our operations to provide you with the best combination of price and servi
Buy It Now
Free Shipping Condition: New Location: Chino, United States This 6" Vise Clamp Machine Will Easily Turn Your Drill Press into a Milling Machine! 1 Vise Clamp Machine. Jaw Width: 15.3cm/ 6in. Jaw Depth: 4cm/ 2in. ... moreApplicable Objects: Water Pump, Pipe, Steel Wire, Clamp Table.
Buy It Now
$12.45 Shipping Condition: Used Location: North Tonawanda, United States South Bend Drill Press.
Buy It Now
Free Shipping Condition: New Location: La Center, United States Drill Chuck 1/2" x JT6. Chuck Key Included.
Buy It Now
$19.20 Shipping Condition: Used Location: Nashville, United States
Buy It Now
$20.87 Shipping Condition: Used Location: Waterford, United States USED, FRONT PULLEY COVER CASTING. IT WILL WORK ON EITHER HIGH OR SLO-SPEED PRESSES. NO CRACKS OR REPAIRS. LOOK AT THE PICTURES.
Buy It Now
Free Shipping Condition: Used Location: Waterford, United States USED, DELTA SPIDER HANDLE. 2 OF THE 3 HANDLES ARE MISSING. THE HANDLE BORES ARE 3/8-24. THE MOUNT BORE IS 1-1/4". NO CRACKS OR REPAIRS.
Buy It Now
Free Shipping Condition: New Location: La Center, United States Drill Chuck 5/8" x JT33 Description: For those that prefer traditional keyed drill chucks. These chucks offer precision and nearly unlimited mechanical ... moreadvantage for tightening and loosening drill bits and tooling. These 1/32" 5/8" JT33 Taper drill chucks have fluted grips and the chuck key is included. Specifications: 1/32" 5/8" JT33 Fluted Grips Chuck Key Included SHIPS PRIORITY MAIL. SHIPS SAME DAY IF PAID FOR BY 4PM PST. THANKS. Payment: You may pay instantly with PayPal by clicking the pay now button at the top. Return Policy 100% Satisfaction Guaranteed 100% Money back Guaranteed All product exchanges must be in 100% brand new condition Please contact us within 7 days upon damaged item is received We will file claim for all buyers on damaged or lost items Exchange. Refund, or replacement will be offered upon buyers request Please contact us for more information by using"ask a question" link at the bottom of the listing Customer satisfaction is our primary goal and we will resolve any problems such as damaged. Not as described, missing parts, and lost items. Please contact us before leaving a negative or neutral feedback. Our office hours are Monday to Friday 8:00am-6pm PST. All emails will be replied within 24 hours except Sat. Sun. and US holidays. Thank you for visiting our store! Terms: Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. Colors or packaging of items delivered may vary from those photographed Payment is expected within 7 days of auction close. We cannot guarantee availability of product if we do not receive payment within 7 days. Shipping: Free shipping to the all of USA unless otherwise stated. Shipping discounts for multiple items will be done on a case by case basis for international buyers. WE SHIP FASTER and SAFER THAN MOST SELLERS JUST CHECK OUT OUR FEEDBACK! We stock all available items. And we ship from our warehouse. Orders are shipped the same or next busi
Buy It Now
$98.67 Shipping Condition: Used Location: North Tonawanda, United States South Bend Drill Press. If you know anything about SB drill presss they are the bets around. They are heavy and built to last. I have most of the parts ... moreto make your own from scratch. Before I found mine that’s what I was going to do and now that I have a parts machine I would love to see someone do the same
Buy It Now
Condition: Used Location: Middlebury, United States Prefer to pick it up yourself?. Country of Manufacture: N/A. Size: Length: 24 in. Width: 17 in. Height: 11 in. Will there be a dock or forklift. Unless ... moreotherwise specifically agreed to in writing by.
Buy It Now
Free Shipping Condition: New Location: Los Angeles, United States A very popular machine. 12-speed drill press works at a maximum speed of 3,050 RPM. Maximum Speed (RPM): 3050 RPM. Bench & Stationary Tool Type: Drill ... morePress. Swing Distance (In.). Minimum Speed (rpm): 140.
Buy It Now
$81.83 Shipping Condition: Used Location: Union Grove, United States Trough table (bench top). Delta Milwaukee.
Buy It Now
Free Shipping Condition: New Location: United States Bosch Gds18v-330Pcn Brushless Impact Wrench Pin Detent. Wera 05075831001 Torque Wrench Set,Cw And Ccw,Sae. Light Industrial. Zoro Select 793Nd2 Black ... moreNipple,Seamless,1/2X14. & Recepticles. Electrical Outlets.
Buy It Now
$125.00 Shipping Condition: For parts or not working Location: Groton, United States
Buy It Now
$5.85 Shipping Condition: Used Location: Nashville, United States As shown, in good used condition, for 2-3/4" o.d. column drill presses.
Buy It Now
Free Shipping Condition: New Location: Jacksonville, United States Here are the details Crank for raising & lowering drill press table. Crank made from cast iron. Drilled and tapped M8 x 1.25 for handle (handlenot included).
Buy It Now
Free Shipping Condition: New Location: Chino, United States PACKING LIST: 1*mini bench drill 1*96W Power adapter DESCRIPTION: Speed: 1000-3000rpm Bench drill size: 10*13*22cm Motor model: 795 pure copper motor ... moreSynchronous wheel 1:2 speed change Drilling stroke: 40mm Chuck specification: B12 (1.5-10mm) Voltage: 110-240V Plug: US plug Scope of application:cutting,grinding,polishing,home Spindle diameter:10 (mm) Condition: New.
Buy It Now
Free Shipping Condition: New Location: Ontario, United States 14 in Floor Drill Press with Laser and DRO - G0794. Swing 14 in. Table Swing 360 degrees. Adjustable laser sight. Drill Chuck 1/64 in - 5/8 in. Owner's ... moreManual. Motor 3/4 HP, Single Phase. Table Tilt 90 degrees left and right.
Buy It Now
$9.00 Shipping Condition: Used Location: North Tonawanda, United States South Bend Drill Press.
Buy It Now
Free Shipping Condition: New Location: El Monte, United States Untitled Document BEST PRICE'D TOOLS& SALES 4 way chuck key(small) Features: 4 way chuck key small: 1. 2, 3, 4, Dropped forged alloy steel. Chuck ... moresize: 1/2" 13mm) 1/4" 6mm) 3/8" 9mm) 5/8" 16mm) payment Paypal is the only form of payment accepted. Payment is expected within 7 days of purchase or wining bid. shipping. Shipping is available for the following: United States. Canada, Hawaii, Puerto Rico. International shipping is available. Shipping costs may vary. All orders are usually shipped the same day after purchase and payment is received Most likely 1 business day after purchase Mon-Fri. Shipping is also available on Saturdays. Payment must be received before 1:00 p.m. PST. Tracking number will be updated to the order after item has been shipped. terms. We stand behind every product we sell. If there's anything wrong with the item you received. Please contact us. No questions asked! You may return the product within 14 days of receipt for a complete refund. Return shipping is the responsibility of the buyer. Buyer is responsible for all return shipping costs. Item must be returned in new condition. As received with all accompanied accessories and literature. Buyer assumes all risk of liability with respect to the purchase and use of the product/item. All of our pictures are photos of actual items. help For help with your order or if you have any questions regarding our products. Please contact us through eBay's internal message system. All messages are answered within 24hrs. 7 days a week. Feedback will be posted right away after product has been shipped. Positive feedback is expected after item has been received. We pride ourselves on making sure each and every customer is satisfied after the sale is complete. If there are any issues or problems please send us a message and we will do our best to resolve the issue before leaving us any negative or neutral feedback. Were here to guarantee complete customer satisfaction.
Buy It Now
Condition: Used Location: Rochester, United States Electric :230/460V 3 Phase. Make: Buffalo Forge Co. Type: Drill Press, Floor Model. The drill press is exactly as pictured. Table Size: 31" x 14". Model: ... moreNO 18.
Buy It Now
$45.75 Shipping Condition: Used Location: Nashville, United States Original paint.
Buy It Now
$16.38 Shipping Condition: Used Location: Waterford, United States USED, DELTA SPIDER HANDLE. THE BORE IS 1-1/4". THERE IS A HOLE DRILLED IN ONE HANDLE. THERE ARE SCUFFS AND SCRATCHES FROM USE.
Buy It Now
Free Shipping Condition: Used Location: La Habra, United States South Bend Precision 14” Drill Press Quill Lock Clamp. Free shipping to the lower 48 United States first class mail
Buy It Now
Condition: Used Location: Louisville, United States MOREY HERCULES RADIAL DRILL PRESS. Column: 7". Power Down feed. 004.008.012. Spindle motor: 2.5 HP. Base table: 2' x 2'. Model: 2'/ 7-1/2". 14 Spindle ... morespeeds: 40 to 2000 rpm. Spindle travel.
Buy It Now
$47.87 Shipping Condition: Used Location: Phelan, United States Will come exactly as shown. Weighs around 40lbs. Does have a bit of rust, grime, and dirt.
Buy It Now
Free Shipping Condition: Used Location: La Habra, United States South Bend Precision 14” Drill Press Quill Pinion. Free shipping to the lower 48 United States
Buy It Now
Condition: Used Location: Coffeyville, United States SWING- 14". DRILLING CAPACITY: 1/2". FLOOR DRILL PRESS. SPINDLE TRAVEL: 3-3/8". SPINDLE DISTANCE TO BASE: 24-1/2". BASE SIZE: 10-5/8" X 14". SPINDLE SPEED: ... more5. SPINDLE DISTANCE TO TABLE: 17-1/2".
Buy It Now
Condition: Used Location: Lenapah, United States No 2 MT Spindle. (185) No 18 Buffalo Gang Drill Press Test - YouTube. All products are as is.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Woodworking Hole Drill Bit Mortise Locator Tenoning Machine for Bench Drilling Specification: Material：steel Applicable machine tools: drilling machine ... moreSize: approx 45*35*20cm Note: 1. This product is used with a bench drill. 2. This product has size requirements for the bench drill used. 3. This product has a requirement for the distance between the drill chuck and the table when in use. 4. The diameter of the clamping part of the square hole drill used in this product is also required. Packing including： 1* Locator Set (excluding bench drill).
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States Product Specification： Clamping Range: 3/16" - 3/4". MT3 Shank. Accuracy: 0.005" Product Description： Super Heavy duty design. Special quenching treated ... morekey parts increases durability. Suitable for drill presses or lathes spindle accepts MT3 shank Jaws are specially engineered to achieve balance. JT3 mounted. Chuck key and MT3-JT3 arbor are also included in the package. Package Including： 3/4" Heavy Duty Drill Chuck 3MT Shank in Prime Quality MT3 Drill Chuck Keyed As Picture Show, Contact Us If Receive With Missing Parts. Please Notice:.
|
|
|
|
Delta Depth Gauge 14" Drill Press w/ Knurled Nuts Stop Collar Clamp, Rod, Bolts
Delta drill press depth stop collar. Gauge, special nuts, washers, special bolts, set screw, etc. Comes off of a 14" drill press. Shop drawings show where part fits onto YOUR drill press. Good gently used condition. No mechanical defects or breaks that I can see. Paint is obviously chipped off in some places, dirt/grease/etc on rod but I do not see any rust. Nuts in good condition, knurling is fine. Special washer(DP-318) included. Only part that I can see that is marked is the Stop Collar(DP-296. See photo) But as near as I can tell, what you get includes the following: DP-273-X Stop Rod DP-295 Stop Collar SP-1005 Nut DP-221 Special Nut SP-622 Bolt DP-275 Special Nut(quantity 2) DP-318 Washer Caveat. Item will be shipped disassembled. I will separate the rod from the collar. You will have to reattach them. It is one nut you will have ... moreto tighten. Ask additional questions to make sure it fits your drill press. Shop drawings from. This is a great site and you ought to check it out if you haven't seen it yet. Also, stop by and visit at if you never have.
|
|
|
Vintage Delta Milwaukee DP220 14" floor model drill press 110V 1/3HP
Delta Milwaukee DP220 14" drill press Vintage 1949 High speed floor model 680-4500 RPM Tilt table 110v~1/3 HP motor Super duty Jacobs geared chuck. Key head. Original paint; other castings sandblasted. Repainted: primed, finish coat Excellent condition $455 Come see it or give us a call with any questions The Tool Consignment Store 560 New Park Ave West Hartford. CT 06110 860-263-7908 You can pick it up or you can get a quote from frieghtquote. com
|
|
|
Delta Milwaukee 14 inch drill press head casting
Main casting of older Delta Milwaukee 14 inch drill press. No structural issues. Heavy item.
|
|
|
Delta Milwaukee DP 220 14" drill press motor mount DP290
Delta part number DP290 motor mount plate. Removed from a DP220 drill press. Please contact me with any questions.
|
|
|
JET 14" Vertical Drill Press w/Portable Cart JDP-14M Jacobs Chuck
SKU: 2359797 A: 0013000000CXCfg O: 0065000000Mje9q PA: View Photo Gallery. Calculate Shipping. Location: Kent. WA 98032 Item Description. This is a no reserve auction for a JET 14" Vertical Drill Press w/Portable Cart JDP-14M Jacobs Chuck. This item is being offered by bidadoo auctions- The largest and most trusted online equipment and industrial auction service in the West. This item is currently owned by The Boeing Company. We have two great eBay stores to better serve you. View our construction and transportation equipment auctions for construction machinery. Fleet vehicles and heavy equipment. View our industrial. Tools and equipment auctions for industrial equipment and tooling. General rental tools, and small equipment. Overview: Make: JET Model: JDP-14M Type: Vertical Drill Press Serial No: 0051105 Features/Specifications: Swing: ... more14" Throat: 7.5" Table Size: 12" diameter Variable Speed: 200-3630 RPM JET Motor: 1/2 HP- 115/230V- 8.0/4.0A 1720 RPM- 60 Hz- 1 PH Jacobs 3-jaw chuck(M: JKP-130-J33) Power cabinet Shop-built portable cart Dimensions& Weight: Dimensions: L 30" x W 24" x H 72" Shipping Weight: 485 lbs Condition: Good- working at time of decommission Normal wear from previous use in working industrial environment Please Note: Due to export requirements set by the consignor of this item. This auction is restricted to bidders with a US-based eBay account only. Additionally, we are not able to ship this item internationally(including Canada& Mexico) if the winning bidder: 1) is not a US-citizen-or- 2) is not bidding from a US-based eBay account. Please Note: Inspections and condition report limited to sound. Sight, feel, and limited operational running/ testing. In addition, all conditions are cross-referenced with service personnel. Operators, and maintenance system records(when available) bidadoo. Inc. makes no guarantees to actual hours. Miles and/or operational condition. Photos and video take priority if there are discrepancies within this listing. Weights
|
|
|
Delta Milwaukee 14" dp 220 drill press return handle assembly
Up for bid is a delta Milwaukee return handle assembly off of a DP 220 14" drill press. Handle is in great condition and will shine up nicely. Please ask questions before bidding. Thank you.
|
|
|
JET JDP-14-J BENCH DRILL PRESS 1/2" DRILLING 1/2HP 2500RPM
BT# 14357 TJ-099.1Y You are looking for: JET JDP-14-J BENCH DRILL PRESS 1/2" DRILLING 1/2HP 2500RPM USED AND TESTED ITEM. IN EXCELLENT CONDITION! 30 DAYS WARRANTY! Manufactured by: JET. Additional info: BENCH DRILL PRESS Model: JDP-14-J Chuck Size 1/2" 14" Swing 1/2" Drilling Capacity 1/2 HP 2500 RPM Visit our eBay store: Check our Store Highlights In addition: Hablamos ESPAÑOL und DEUTSCH Domestic handling time(turnaround) 5 business days We ship with: Powered by
|
|
|
Delta 14-040 Drill Press + Drill Chuck + NO RESERVE
Manufacturer: Delta Model: 14-040- Drill Press Drill Chuck Included! Serial: R9116 Condition: We do not know the working condition of this machine. We do know it was being used at the school in which it's located until they stopped using it and declared it as surplus. There is an arm missing from this machine. Does not affect the operation of driving the drill head down. Note: Please view our other auctions as we are selling many assets at NO RESERVE! Note: All items being sold for this school district are being sold AS-IS and for LOCAL PICK-UP ONLY. NO SHIPPING. There is a forklift that will be on site to assist with the removal of your item(s) REMOVAL: ALL ITEMS MUST BE REMOVED BEFORE JUNE 24th. WE HAVE 3 DATES SET ASIDE FOR THE ASSETS TO BE REMOVED AND THEY ARE: JUNE 19th. JUNE 20th AND JUNE 21st. ALL DAYS WILL HAVE THE REMOVAL TIME ... moreOF 8-3. THIS SCHOOL IS BEING DEMOLISHED ON JUNE 24th AND ANYTHING LEFT IN THE BUILDING WILL BE DEMOLISHED WITH IT. NO OTHER PICKUP DAYS ARE ALLOWED. Note: At the end of the auction. We will give the winning bidder the contact information for the administrator at the school(Holland, MI) in which all the assets are located. Once this information is received, it is up to the winning bidder to make contact and set up an appointment for removal. Please keep in mind that these items are being sold for a school district. It is not always easy to make contact. It is necessary to be persistent until you get hold of the administrator in charge. HP: 1/2 R.P.M: 1720 Electrical: 115/ 230 V 1 PH*Item specs. were obtained from the internet and are checked for reasonability only. Please independently check all specs. to ensure accuracy. All items are being sold for Holland Public Schools are being sold As-Is. Powered by The free listing tool. List your items fast and easy and manage your active items. Powered by The free listing tool. List your items fast and easy and manage your active items.
|
|
|
Delta DP 220 14" drill press high speed and low speed pulleys
Up for bid is the high speed and low speed pullys off of a delta dp220 14" drill press. They are both in good shape but dirty. The high speed pully has a couple very minor bends in the fins but nothing that would mess with the functionality of the pulley. There are no cracks or breaks in the pulleys. These are just for the spindle. Not the motor. You would need to find the motor pulley. I am not sure if they used the same pulley for the motor for high and low speed. Please ask questions before bidding. Thank you.
|
|
|
Delta Milwaukee 14" DP220 drill press base for stand alone press
Up for bid is the cast iron base off of a Delta dp 220 drill press. This is the stand alone type. Not the smaller bench top type casting. Item is in good condition. There is one blemish I assume from the original casting. It is shown in the second picture. It is a small hole that goes through to the inside. There are no cracks around it or sign of damage so I am pretty sure this is from the original castin and could be filled easily. It weighs about 50 pounds, hence the shipping cost. Please ask questions before bidding. Thank you.
|
|
|
JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS - #JDP-14M
aims JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M read Terms& Conditions LOCAL PICKUP AVAILABLE! MONDAY THROUGH FRIDAY: FROM 1:00 PM TO 4:30 PM PST Made by Jet. This is a used Heavy Duty Multiple Speed Drill Press in working condition. Model# JDP-14M Serial# 9090066 Stock# 354069 Specifications: Tables: Production Table Size: 12-1/4" diameter Production Table Tilt: 45 degrees L/R Base Working Table Size: 8-1/4" x 8-1/4" Spindle: Throat: 7" Swing: 14" Taper: 2 Morse Taper Spindle Travel: 3-3/8" Spindle Speeds(16) 200 to 3.630 rpm. Column: Column Diameter: 2-7/8" Column Length: 24" General: Motor: 1/2 Horsepower. 1,720 rpm, 115/ 230 Volt, 8/ 4 Amps, 60 Hz Electrical: 115 Volt. Single Phase Overall Dimensions: 13" x 27" x 40" tall. Comes as shown in pictures. To go to The ... moreManufacturers Website: Check out the photos! if you have any other questions. Give us a call or email. Reliable Tool currently has a large selection of products listed, please check out our other auctions in this category by visiting our page for more Great Deals! Bidding starts at a dollar with no reserve. JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M JET 14" MULTIPLE SPEED BENCHTOP DRILL PRESS- JDP-14M Reliable Tool Inc. c 2011 | Powered by
|
|
|
Delta 14-070 14" Drill Press
For auction. A Delta 14-070 drill press, in good working order. Posted with
|
|
|
1945 Delta Rockwell 14" Drill Press
For sale is a nice 1945 vintage Delta 14" drill press. Catalog/model number 17-207. This is the slow speed model with 4 speeds of 470. 780, 1300 and 1950 RPM. The drill press has a single phase. 1/3 HP Delta Repulsion-Induction motor and is wired to run from a standard 120 volt wall plug. The motor has new bearings and has been repainted. The drill press has the original finish that is little tired. I.e. some rust is visable on the surface. The spindle bearings are in good condition. New cord. Switch and belt installed. The drill press has 0.002" run-out as measured on a pin 1.5" down from the Jacobs 6A chuck. The table has a few marks, but no drill bit thru holes. PS the cart is not included with the drill press. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*60c23f%60%3E-13f687b8257-0xd9-
|
|
|
Delta milwaukee 14 inch drill press depth marker
As shown. Came from a 14 inch Delta Milwaukee drill press
|
|
|
delta milwaukee 14 inch drill press return spring
Works fine. Came from a 14 inch delta milwaukee drill press
|
|
|
Delta Rockwell Milwaukee 14" Drill Press Depth Index Pointer DP-220 Head Casting
DEPTH INDEX POINTER FOR A DELTA ROCKWELL MILWAUKEE 14" DRILL PRESS WITH A DP-220 HEAD CASTING. I AM ALWAYS WILLING TO COMBINE SHIPPING WHEN POSSIBLE. Will be parting out a Vintage 14" Delta drill press including all parts. Retirement light and original motor. If you need any parts please message me. Using the"ask a question" function.
|
|
|
*DELTA Milwaukee* ~ 14" Drill Press Multi-Speed Attachment~ with Spindle Pulley~
Here's a Vintage DELTA Milwaukee Multi-Speed Attachment for 14" Drill Presses It's an optional attachment for drill presses which can be used with with either the Slow speed spindle pulley(the big one) or the High speed spindle pulley. The motor(drive) pulley is the same in either case. You would get this attachment with two V-belts. The only difference between the No.1028 model and the No.1029 model was the length of the belts. The V-belts are Not included in this listing. In the upper left of the diagram it says: Foot feed bracket may be cut off. If not used. Apparently the original owner did just that. Having that minor modification does not. However, affect the functionality of this part in any way. As you can see. In the diagram, adding this attachment to your 14" drill press gives you the option of 12 speeds versus ... more4. In this listing. In addition to the Multi-Speed attachment, I am including your choice of 1 of the Spindle pulleys. You can have EITHER the Slow speed. Or High speed pulley. you already have one on your drill press. So my suggestion is that you pick the pulley that you don't already have; but it's up to you. Just email me. And I'll include the one you request in the shipment. Thus outfitted, you will then have 24 optional speeds available to you with your 14" Delta drill press. see diagram for list of speeds) Both the Multi-Speed attachment and Spindle pulley are in Great Working Condition! Let me know if you've got any questions. 14-Day Return Free Shipping! Thanks!
|
|
|
DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD
aims DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD read Terms& Conditions LOCAL PICKUP AVAILABLE! MONDAY THROUGH FRIDAY: FROM 1:00 PM TO 4:30 PM PST Made by Delta Machinery. This is a Multiple Speed Pedestal Drill Press Head. Unit does not respond to power. Selling AS-IS for parts or repair. To the best of my knowledge. The specifications I've provided are correct but please verify or inspect machine first hand. The machine can be inspected by appointment. Unit is being sold as is and our normal return policy does not apply. Specifications: Throat: 7" Swing: 14" Quill Depth: 4" Column Diameter: 2-3/4" Column Height: 30" Overall Dimensions: 23" x 12" x 31" tall. Comes as shown in pictures. Check out the photos! if you have any other questions. Give us a call or email. Reliable Tool currently ... morehas a large selection of products listed, please check out our other auctions in this category by visiting our page for more Great Deals! Bidding starts at a dollar with no reserve. DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD DELTA 14" MULTIPLE SPEED DRILL PRESS HEAD Reliable Tool Inc. c 2011 | Powered by
|
|
|
Vintage DELTA MILWAUKEE 14" DRILL PRESS DP220 Spindle KEYLESS GRIP CHUCK
I will be listing an awesome 1946 DELTA MILWAUKEE ROCKWELL Floor Model Drill Press this evening as well as a nice variety of ACCESSORIES including SPINDLES. CHUCKS. PULLEYS. MORTISING ATTACHMENTS. And more so please see all of my Listings. I do offer combijned shipping! For your bidding consideration in this auction is the following Torque Tool or accessory: LOT# 7 ITEM: Delta Milwaukee Drill Press DP220 14" Spindle WITH A Keyless Chuck Attachment on it. DESCRIPTION: This item was found in a Box marked"Delta DP220 Drill Press Accessories" and is being sold as such. And as-is, so please view photos and ask questions. MEASUREMENTS: The spindle is 5/8" diameter and it measures 17" long overall. The Chuck measures 2" in diameter and 3 3/4" long. CONDITION: Used but in very nice cosmetic and working condition. ... morePlease note. I closed the chuck for the photo but have not been able to re-open it. I am not familiar with this vintage Chuck so if anyone knows the key to re-opening it please let me know and I will report the results. SELLERS TRADE PRACTICES: I want your Bidding and Purchasing experience with me to be a satisfactor y one in every way. I have provided a few thoughts below to help you understand my practices and what has proven to work successfully for me and over 5000 of my customers in ensuring an above satisfactory transaction here on Ebay. Please let me know if you have any questions or comments! FEEDBACK: I gladly provide POSTIVE FEEDBACK once our transaction has been completed to your satisfaction and I have recieved your Positive Feedback. PAYMENT: I accept Paypal payment and you should pay for your items within 4 days of the Auction close. I use Ebay's system for payment reminder and notification. LISTING/ ITEM DESCRIPTION: Please ask questions- I try and describe items as best I can. And add corresponding Photos, but I don't always know what may be important to you. RETURN POLICY: I accept returns for full refund within 7 days of the auction close date if your
|
|
|
VINTAGE WALKER TURNER 14" DRILL PRESS HEAD CASTING - NO CRACKS OR BROKEN PARTS
I will gladly ship multiple items together as long as it is safe to do so.
|
|
|
VINTAGE WALKER TURNER 14" DRILL PRESS HEAD LOCK
This secures the head to the column. I will gladly ship multiple items together as long as it is safe to do so.
|
|
|
VINTAGE WALKER TURNER 14" DRILL PRESS QUILL ASSEMBLY
Includes the quill assembly with the chuck and depth collar. No nuts. I will gladly ship multiple items together as long as it is safe to do so.
|
|
|
VINTAGE WALKER TURNER 14" DRILL PRESS BASE
Includes odd-ball top& bottom bearings. With sleeves. The bearing are dry and need grease. Please contact me for an accurate FedEx quote as the EBay calculator does not take over-sized packages into consideration.
|
|
|
Delta Milwaukee 14 inch drill press spindle pulley new bearing!
Spindle pulley for Delta 14 inch drill press with new bearing. good working order.
|
|
|
Delta Milwaukee 14 inch drill press motor pulley
4 speed motor pulley to match the spindle pulley of the DP 220 casting spindle. 1/2 bore. Good working order
|
|
|
Delta Milwaukee 14 inch Drill press spindle with new bearings
As shown. Good working order. Bearings are obsolete. So had adaptor sleeve made to recreate new bearing. The sleeve is held into the bearing with lock tight and the bearing has a slip fit on the shaft. The sleeve is then notched to lock onto the shaft. In the end, in functions just like the original. Paid $60 for these sleeves! Fits the DP 220 casting for 14 inch drill press
|
|
|
Delta Milwaukee 14 inch drill press multi speed pulley metal working extras!
Ready to go! Plus original paperwork. Pulley was glass bead blasted to clean up and bearing replaced. Bulletin for installation and drill press owner's manual. Hard to find!
|
|
|
VINTAGE 14" DELTA ROCKWELL DRILL PRESS QUILL PINION
FROM CAT#14000 FOR REF. 1 1/4" BODY DIA. 13 TOOTH PINION 1/2-20 STEP DIA. FOR SPRING DRILLED HOLE FOR 7/16 HANDLE(NOT PROVIDED) O/A LENGTH 8 5/8 WITH 3/8-24 HANDLE THUMB SCREW LOCK PINION SHOWS HARDENED GREASE WITH NO APPRECIABLE WEAR. FEW MARKS ON BODY O.D. FILED AND POLISHED NEEDS A GOOD CLEAN AND POLISH. GOOD USEABLE PART COMPLETE PART-OUT
|
|
|
BENCH MODEL BASE FOR 14" DELTA DRILL PRESS
Nothing cracked and nothing welded. Very nice base.
|
|
|
DELTA MILWAUKEE 14" BENCH TOP DRILL PRESS
RIMCO ROBERT IVENS MACHINERY COMPANY 613 W. Bruce St. Milwaukee WI 53204 414-272-6686 Welcome to Robert Ivens Machinery Company Our Mission: Productive and Satisfied Customers. Up for AUCTION: DELTA MILWAUKEE 14" BENCH TOP DRILL PRESS In good/used condition New bearings all around Runs well and will serve many happy years! Wood workers quill and table STD speed pulleys Original motor with new switch 1/3HP 1 phase 110/220v Serial no. unk. Check photos for details I SHIP ITEMS THIS HEAVY ALL THE TIME. ASK ME FOR A QUOTE! Email us with any questions! WE COMBINE SHIPPING! Check out my! Be sure to add me to your! Robert Ivens Machinery Company(RIMCO) is Wisconsin's largest dealer in used woodworking machinery A sole proprietorship in business for more than twenty-five years, RIMCO's business philosophy is based upon value and customer ... moresatisfaction. If you have an interest in woodworking machinery. You are welcome to call and ask about our extensive. Ever changing inventory. Your business will be most appreciated.
|
|
|
Old Style Delta 14" Drill Press Jacobs Chuck Spindle
Old Style Delta 14" Drill Press Jacobs Chuck Spindle. Cat. No. 972. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press 1/2" Router Spindle
Old Style Delta 14" Drill Press 1/2" Router Spindle. Cat. No. 974. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Quill Clamp for a Delta 14" Super Hi-Speed Drill Press
Quill Clamp parts for 1940's Delta Hi-Speed drill press. Part Numbers: SP-604. SP-7, SP-27. DOES NOT INCLUDE SP-26 but this can be easily made on a lathe. SP-26 is just a 3/8"16 knurled nut. The important part is the SP-7 which is no-longer available and is more difficult to make. Find Schematics for this drill at:
|
|
|
JET DRILL PRESS JDP-14MF 14' SWING 5/8" CAPACITY 3/4HP 1PH (7302)
AMP 12/6 115/230V KW: 0.55 4 POLE RPM 1720 CAN ARRANGE SHIPPING PICK UP LOCATION 4703 WEST ARTHINGTON STREET CHICAGO. IL, 60644 TEL: 773-626-3366 MON-FRI. 7AM-4PM.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-144b62b87c2-0xf4-
|
|
|
VINTAGE DELTA MILWAUKEE 14" DRILL PRESS BELT GUARD
This is the cast iron front guard and cast aluminum rear guard. The front badge has been wiped clean so no logo can be seen. There is a small clip to post work orders on mounted on the side of the rear guard. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp*4a24%60%3C%3E-144bd3db597-0xfe-
|
|
|
Powermatic 1150 14" 3/4HP Floor Drill Press, 115V, 1-Phase
Powermatic 1150 14" 3/4HP Floor Drill Press General Info: Stock# CB-141002-13 Machine Name: Powermatic 1150 3/4HP Floor Drill Press Condition: Used. Fair Tested: Yes. Working Condition Brand: Powermatic Model: 1150 Serial: 815V1241 Year: N/A Shipping Weight: 750 Lbs. Shipping Dimensions: 48" L x 40" W x 78" H Location: Stone Mountain. GA Specifications: Powermatic 1150 14" Floor Drill Press. 14" Swing. 3/4HP Motor, 115/230V(Wired 115) 1-Phase, 1/2" Jacobs Chuck Spindle Taper, Variable Speed 238 to 4800 RPM, 6" Spindle Travel, 3" Column Diameter, 14-1/4" x 10-1/4" Table Working surface, Cord& Plug. Additional Info: The Powermatic 1150 Floor Drill Press has been tested and is in working condition. Currently. Machine can be turned on/off by plugging or unplugging cord. Everything works ... moreon drill press, but there are a couple spots in the variable speed control that can be tough to turn pass. If you currently have surplus equipment you are not using, visit our to get a price quote on what we will buy or trade it for. Seller Contact Information: Mark Davis 404-272-1285 The Equipment Hub. LLC 1380-A Beverage Dr. Stone Mountain. GA 30083 Are you looking for a different machine than the one listed? Visit our to see other machinery options. It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week. Visit Us on the Web at
|
|
|
Boice-Crane Co. 14" 2HP Bench Type Drill Press, Vintage, Classic, 110V
Boice-Crane Co. 14" 2HP Bench Type Drill Press General Info: Stock# CB-141002-32 Machine Name: Boice-Crane Co. 14" 2HP Bench Type Drill Press Condition: Used. Good Tested: Yes. Good Working Condition Brand: Boice-Crane Model: 1600AF Serial: 114 Year: N/A Shipping Weight: 200 Lbs. Shipping Dimensions: 48" L x 40" W x 48" H Location: Stone Mountain. GA Specifications: Boice-Crane Co. 14" Bench Type Drill Press. 2HP Motor. 110V, 1-Phase, 1725 RPM, 14" Swing, 2-3/4" Column, 10" x 11" Table. Additional Info: The Drill Press has been tested and is in good working condition. A real nice heavy duty bench top drill press. If you currently have surplus equipment you are not using. Contact us to get a price quote on what we will buy or trade it for. Seller Contact Information: Mark Davis 404-272-1285 ... moreThe Equipment Hub. LLC 1380-A Beverage Dr. Stone Mountain. GA 30083 Are you looking for a different machine than the one listed? Visit our to see other machinery options. It is always recommend to come out and inspect the machinery listed before purchase. If you have any specific questions or would like to set up a time to view this piece of machinery feel free to contact the contact person for this listing 7 days a week.
|
|
|
DELTA ROCKWELL 14" - 15" DRILL PRESS MANUAL FOOT FEED ARM / BRACKET
Delta Rockwell arm for the manual food feed set up. I don't have any other parts for the system just the arm pictured. The arm is in good shape. 2-3/4" ID Bore. Returns accepted. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf%60%60%3E-1456935ee9b-0x10c-
|
|
|
Vintage Delta Rockwell Drill Press Return Spring Assembly 15" or DP225 14"
Up for auction is a Vintage Delta Rockwell Drill Press Return Spring Assembly 15" or DP225 14" It comes as pictured. Please review pics attached. Good luck bidding.
|
|
|
Old Style Delta 14" Drill Press Accessory Spindle
Old Style Delta 14" Drill Press Accessory Spindle. For buffing wheels, etc. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press #1 Morse Taper Spindle
Old Style Delta 14" Drill Press#1 Morse Taper Spindle. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Old Style Delta 14" Drill Press 5/16" Shaper Spindle
Old Style Delta 14" Drill Press 5/16" shaper cutter Spindle. Used, scratched, a little light rust etc. from sitting around the shop for years.
|
|
|
Delta DP220 14" Vintage Drill Press, 1/3 HP, 115V, 1PH
Delta Approx. 15" Swing Vintage drill press, Cleaned and checked, Model DP 220, 1/3 HP motor. 115V, 1PH, 1750 RPM, Stock Number: B-1-110(w) Framing or crating will incur additional charges. If needed Please Email or call 1-800-793-4494 if interested in this machine. Many other new and used machines are stored in our warehouse and can be viewed. Shipping& Freight: Purchaser/Buyer/Winning Bidder pays all shipping/freight costs associated with getting this machine to your location if item is to be shipped and not picked up in person. DELIVERY: Varies upon warehouse workload and potentially the item. This item may be released immediately by the warehouse. But sometimes up to 7 business days are needed to prep and release said item. Subject to Prior Sale. This item may be withdrawn from sale at any time as it is listed on our website ... moreand in other advertising. PAYMENT TERMS: Full Payment or deposit required within 24 hours of order. NO EXCEPTIONS. Items not paid for or held via deposit after 7 days will immediately be reported to eBay as unpaid! Cash in person, M.O. Personal/Company Check or Visa/Mastercard/Discover accepted. Wisconsin Sales and Use tax of 5% required for all purchases by Wisconsin residents who do not have a tax ID or are not able to fill out an exemption claiming the machine for business/manufacturing use. Minimum $125.00 Crating Fee. If required. Used equipment is sold as is. Where is, unless otherwise specified. SELLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Freight. Rigging, and installation are not included unless otherwise specified, but arrangements can be made at an additional cost. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-14663017b11-0x135-
|
|
|
Delta Rockwell ?? 14" ? Drill Press 2 & 3/4" COLUMN TABLE BASE BRACKET FLANGE
DELTA ROCKWELL( Drill Press COLUMN MOUNT. BASE, BRACKET, FLANGE, STAND in GREAT MECHANICAL working condition and in VERY GOOD Shape! Takes a 2.75" column. Ask questions and check out the photos carefully as I don't offer refunds except when I make a huge error in the listing. Shipping is $9. You will need to specify if you wish insurance. I usually ship w/in two working days after the day payment is made. I greatly prefer payment via Paypal and within two days of auction close. Bid early and often! Please check out my other listings!
|
|
|
ND-88100 Spindle Bearing for 14” Delta Drill Press
ND-88100 Spindle bearing for Delta 14” drill presses. Also known as part C88100 and SP5342. Excellent condition. Used. These bearings are no longer available. Made in the USA. Worldwide shipping; if you are outside the United States. Please contact me for a quote unless the shipping cost is stated on the Shipping and Payments tab. See my other listed items. gsrx_vers_586(GS 6.8(586)
|
|
|
14" DELTA #14-070, SINGLE SPINDLE DRILL PRESS FLOOR TYPE
14" DELTA SINGLE SPINDLE DRILL PRESS MODEL 14-070 FLOOR TYPE RACO Stock Number R016780 COLUMN TO DRILL CENTER- 7" SWING- 14" SPINDLE- JACOBS#33 TABLE SIZE- 11" X 11" QUILL STROKE- 3.3" SPINDLE SPEEDS- 12) 250 TO 3000 RPM MOTOR- 1/2 HP 115/230/1/60 EQUIPPED WITH- DRILL CHUCK TILTING TABLE TABLE ELEVATING MECHANISM DIMENSIONS(IN. 12 X 26 X 65
|
|
|
14"Rockwell delta drill press quill and jacobs chuck
good condition. the return spring broke. I bought a nicer press, so parting this one out. numbers on tagr1124 and 1666162
|
|
|
Dayton 3Z917C 5-Speed 14" Floor Model Drill Press
Dayton 3Z917C 5-Speed 14" Floor Model Drill Press. Split Phase Motor Used Fully Functioning Ready For Work! g6.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2B%3Eg6%3E-14a1a651ae5-0x103-
|
|
|
Continental Floor Model Drill Press Model DPF-14-12
Page This is a Continental Floor Model Drill Press Model DPF-14-12 Brand/Model: DPF-14-12 Machine Type: Drill Press Motor: No Motor Elect.Voltage: Phase Dimensions: 12" Round Table Chuck 5/8" Comment: Unit has some surface rust. Please utilize our scheduled inspection time to view the item(s) first hand and up close. Please check the location of this listing. Many of our item(s) are for local pick up only. This item is used and sold as-is. Due to the location. This item was NOT TESTED for operation. IThis item was removed from an operating environment. Item may need service and/or parts to make operational. Forklift may be available on site to assist in loading on pickup day. However. NO loading dock is available at this location. Buyer will be responsible for all equipment. Tools, personnel and transportation necessary for loading ... moreand removal from site. Please contact us for additional information before bidding. PLEASE NOTE: If you pay immediately at the end of auction using the eBay payment method please include the 8.25% sales tax or wait for the InterSchola invoice. Which will include the sales tax and should arrive shortly after auction end. Failure to include tax on your payment. Unless you can provide a valid resale certificate or shipping out of state, can result in missing your pick up dates and additional fees. Please read the listing carefully for our policies. Thank you. Inspection Date: 10AM on Wednesday. January 15th, 2015. Inspections are by appointment only. Please use"Ask Seller Question" to request location. Local Pickup ONLY. This item is scheduled for pickup on the following date(s) ONLY: Thursday. January 22nd 2015 at 10:00 AM or Friday. January 23rd 2014 at 10:00 AM. In order to confirm pickup of your item on the earliest date provided in this listing, payment must be received by 12:00 Noon Pacific Time at least 1 business day prior to that date. Pickup information will NOT be provided until payment has been confirmed. If you are unable to pick up this item on one of the
|
|
|
Delta DP 220 Drill Press 14" inch DP220
Delta DP 220 Drill Press 14" inch Delta Drill press 14" inch DP 220 Double duty motor Model K214A HP 1/3 Volt 115/230 Type SR Frame 164 Amp 6.6/3.3 Used. Taken out of a working plant Email or call 920-684-9999 w/ questions Please read prior to bidding You are buying the above as is(If you are not sure what that means. Look it up AS IS) This means don't assume anything. If you have a question, ask. If it is not listed as NEW, then don't assume that it is. It is sold as seen, as is. Unless an item specifically states that is has been tested, it has not been tested. If you would an item to be tested and can tell us how to do so, please call/email us and we will make every attempt to do so. However, please understand that our business is rigging and we are not electrical engineers. Most items were removed from working machines ... morebut are still sold AS IS.Feedback will only be left if you leave positive feedback. EBAY has removed the sellers right to post anything other than positive feedback and we feel that positive feedback should be mutually reciprocated. Lastly, if you try to threaten use of negative feedback to get something that was not listed or a service that was not listed, we will forward the request to EBAY without notice. SHIPPING Buyer is responsible for all shipping/insurance costs. Shipping size and weight for the unit are as follows: 177 pounds with the pallet. Dimensions are 33"x32"x71" high. We will load for you at no additional charge from a commercial building with a loading dock and the driver does not need to come inside. We will provide your shipper with a bill of lading and any other paperwork you require to ship the unit. Please fax any additional paperwork to us after payment has been made. Note that Wisconsin residents are required to pay 5.5% sales tax unless exempt. We require payment within 4 days of purchase. Please call 920-684-9999 or email us via ebay with any questions.
|
|
|
Grizzly G-1200 12 Speed Heavy-Duty 14" Floor Drill Press In EXCELLENT CONDITION
Grizzly G-1200 12 Speed Heavy-Duty 14" Floor Drill Press EXCELLENT CONDITION MT-2 SPINDLE 12 SPEEDS FROM 50 RPM TO 3100 RPM SERIAL# 81432 90 DEGREE LEFT& RIGHT TILT TABLE 5/8" CHUCK CHUCK KEY 1/2 HP MOTOR RUNS@ 1725 RPM 9 AMP/ 110V 150 LBS I TAKE EXCEPTIONAL CARE OF MY TOOLS THIS HAS HAD MINIMAL LIGHT USE ONLY I PREFER LOCAL PICKUP BUT CAN BE SHIPPED FOR APPROX $74.00 DEPENDING ON LOCATION
|
|
|
INDUSTRIAL DRILL PRESS, 14", 16 SPEED, NORTHERN TOOL, RDM-100F
This Drill Press was purchased new on 6-21-1994. It was hardly used in a small machine shop. I have the original manual and Warranty Registration Card. Very Good Condition. Works great! 14" Drill Press 16 Speeds. Model# RDM-100F. Serial# 01743. Purchased Date: 6-21-1994.
|
|
|
Delta Foot Feed Attachment Fo 14" Drill Press Walker Turner Rockwell Atlas DP220
Store*Here we have another ULTRA RARE find for your vintage Delta DP. Here we have a Delta Foot Feed Attachment for 14" Drill Presses. As you can see from the pics. All is in excellent condition. All is complete, except the bolt for the upper bracket(pic 9) which you can pick up at the local hardware. While this is made for the DP220. It fits a 2 3/4" column, and may be adaptable to other vintage drill presses that use the same column. Feel free to ask any questions you need. The last three pics of paperwork are for reference only. I'll print them out for you. But I do not have the original paperwork. If you miss this opportunity. Good luck finding another another, especially one as complete, and in such great shape.
|
|
 |