|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: Used Location: San Francisco, United States Applied Motion Products Step Motor Drive Model# PD5580 Features• Drives sizes 14(1.4" through 42(4.2" step motors• Built in 80 volt power supply(accepts ... more110 or 220 VAC power. 60 Hz only) MOSFET pulse width modulation switching amplifiers(3 state) Phase current from 0.5 to 5.5 amps/phase(switch selectable. 51 settings) Step. Direction, amplifier enable inputs, fault output, optically isolated• Microstepping from full step through 1/ 254(switch selectable. 16 settings) Overtemp and overcurrent(short circuit) and surge protection• Idle current reduction(50% Switch selectable) pluggable screw terminal connectors Applied Motion Products Step Motor Model# 5034-404 Features DC 1.O7V. 3.97A, 0.27OHM, 200S/R Removed from Functioning Equipment If you need more photos. I can send them to you. If you have any questions. I will do my best to answer them. Please be as specific as you can. International bidders please contact first to get shipping quote before bidding. Ship worldwide and use UPS or Canada Post. Please be aware that international shipments may be subject to duty and brokerage fees which are not included in shipping charges.
Buy It Now
Free Shipping Condition: New Location: United States 2, Stepper Motor Driver with 4.2A Current, 128 Microstep DQ542MA. It is designed for use with 2-phase hybrid stepper motor of all kinds with. 4.0A phase ... morecurrent. Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: China Stepper Motor Driver DQ542MA. Holding torque when DQ542MA runs under high speed, is also significantly higher than the other two-phase driver, what’s ... moremore. 3.0Nm(425oz. 4PCS Nema 23 Stepper Motors WT57STH115-4204A Single round Shaft4.2A 425oz-in. ).
Buy It Now
Free Shipping Condition: New Location: Chino, United States Bracket: Material: Aluminium Rod, Plastisol Propeller. Do You like Fishing on the River?. Do You Want to Go Boating with Your Family?. but Are You Worried ... moreAbout the Manual Boating Is Too Tired?. with Our Fishing Boat Engine, You Don't Have to Worry About This Problem.
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Specification: 1.Double H bridge drive 2.Chip L298N(ST NEW) 3.Logical voltage 5V 4.Drive voltage 5V-35V 5.Logical current 0mA-36mA 6.Drive current 2A(MAX single bridge) 7.Storage temperature-20 to +135 8.Max power 25W 9.Weight 30g 10.Size:43*43*27mm This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V, it can enable the onboard 5V logic power supply;afterthe power supply.Don't input voltage in the interface+5V power supply.But you can lead the 5V for external use. when ENA enable IN1 IN2 control OUT1 OUT2 wh
Buy It Now
$5.95 Shipping Condition: New Location: Saukville, United States This Stepper Drive Control Board with model number we19d6vc8g is exactly what you need to control your stepper motor with precision. It is compatible ... morewith a wide range of industrial automation and motion controls, making it ideal for businesses and industries that require reliable and efficient performance. The 3067-01-17R board is designed to deliver smooth and accurate control of your stepper motor, ensuring that it operates at its optimal speed and efficiency. Its compact and robust design makes it easy to install and maintain, and it is built to last with high-quality materials. Whether you are looking to improve the performance of your machinery or simply need a replacement board, this Stepper Drive Control Board is an excellent choice.
Buy It Now
Free Shipping Condition: New Location: United States Q1:why other supplier's TB6560 driver has 3.5A/3A current,but yours is 2.5A?. Supports a lot of stepper motors. 4-wire 0-3.5A normally 3A, the 3.5A is ... morethe peak currentcan be regulated rate current output, bipolar stepper motor driver.
Buy It Now
Free Shipping Condition: New Location: North Royalton, United States High-current 43A. Maximum current: 43A. 1BTS7960 43A High Power Motor Driver Module/ Smart Car Driver Module. R_IS: forward drive current alarm output. ... moreL_IS: Reverse drive current alarm output. 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board.
Buy It Now
Free Shipping Condition: New Location: Hainesport, United States X/Y/Z/A four-axis drive, Y-axis double drive. Support for rotary axis. --PWM/TTL software to adjust laser power. --A4988 driver support most Nema17 motor. ... more--It can be connected to a high-power driver.
Buy It Now
$39.85 Shipping Condition: New – Open box Location: Hawthorne, United States Drive Input: 95-132 VAC | 50/60 Hz. Drive Output. Part Number: ZETA6104-57-51. If you need a new/used item with a specific firmware, series.etc. or a ... morelarge quantity, we probably have it. Do not break the seal/security labels or your warranty will be void!
Buy It Now
$1.50 Shipping Condition: New Location: China Module power consumption: 0.6W(excluding load motor)/static 0.1W. Response speed: K1, K2, 20ms, SW1, SW2, 50ms. Due to the light and screen difference, ... morethe item's color may be slightly different from the pictures.
Buy It Now
$20.00 Shipping Condition: New Location: Sacramento, United States Morphs to full step at higher speeds to maximize motor torque. Optoisolated STEP, DIRECTION, AND DISABLE inputs. 350 kHz maximum step pulse frequency. ... moreRecirculate mode while motor is stopped. Drive Specks.
Buy It Now
Free Shipping Condition: New Location: Plainville, United States New L298N DC Stepper Motor Driver Module Dual H Bridge Control Board for Arduino Description: 1.Using L298N made by ST company as the control chip.The ... moremodule has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Specification: 1.Double H bridge drive 2.Chip L298N(ST NEW) 3.Logical voltage 5V 4.Drive voltage 5V-35V 5.Logical current 0mA-36mA 6.Drive current 2A(MAX single bridge) 7.Storage temperature-20 to +135 8.Max power 25W 9.Weight 30g 10.Size:43*43*27mm Package included: 1x New L298N DC Stepper Motor Driver Module Dual H Bridge Control Board for Arduino(not include the screws) Shipping: Items will be shipped within one business day after payment received. Items are shipped from China using Airmail. Reach most of the countries within 10 to 25 business days. Delivery time depends on destination and other factors. It may takes up to 20 business days. Country Delivery Time Working Days(not including holiday) 5-7 8-11 12-14 15-19 20-22 22 Working Days + Saturday + Sunday 5-9 10-15 16-20 21-25 26-30 31 United States Rate(item arrived) 5.1% 50.1% 29.6% 10.5% 4.7% Refund United Kingdom Rate(item arrived) 9.9% 63.2% 19.1% 3.4% 4.4% Refund Australia Rate(item arrived) 21.4% 50.0% 14.3% 7.2% 7.1% Refund France Rate(item arrived) 10.5% 28.6% 43.8% 10.1% 7.0% Refund Germany Rate(item arrived) 11.1% 22.2% 30.3% 20.9% 15.5% Refund Canada Rate(item arrived) 0.0% 47.1% 31.4% 17.6% 3.9% Refund Spain Rate(item arrived) 3.5% 25.0% 47.9% 12.9% 10.7% Refund Payment: We accept PayPal only. All major credit cards are accepted through secure payment processor PayPal. Payment must be received within 7 days of auction closing. If you
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States Product parameters: Model: 4.0 horsepower jet pump Displacement: 55cc Transmission ratio: 2.08 (27:13) Number of cylinders: 1 Speed: 4500-5500 rpm Gear ... moreshift: clutch Packing volume: 95*42*29cm Ignition system: CDI Cooling system: wind cooling Control system: tiller control Start mode: manual start Refueling method: No. 92 unleaded gasoline is recommended Gross weight/net weight: 13/9.7kg Bore*Stroke: 44*33mm Recommended engine oil: four-stroke engine oil Tilt angle system: manual tilt Size: 855*365*220mm Standard fuel tank: built-in 1.4l Adapted stern board height: 440mm Precautions: 1. Use four-stroke special engine oil (automobile and motorcycle engine oil); 2. Add oil according to the scale indication on the oil dipstick (the rotating cover), do not.
Buy It Now
Free Shipping Condition: Used Location: Sacramento, United States The Newport UniDrive6000 Multi-Axis Universal Motor Driver is a rack-mountable six-axis universal motor driver. A single, universal motor driver card ... morecapable of driving both DC motors up to 200 Watts and stepper motors with up to 250x micro-step resolution is used.
Buy It Now
Free Shipping Condition: New Location: United States 3 PCS Wantai Nema 23 Stepper Motor Dual shaft ,57BYGH115-003B,3A, 428oz-in holding torque. The DQ542MA is an economical microstepping driver based on ... morepatented technology of Wantai Motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors.
Buy It Now
Free Shipping Condition: New Location: United States ♞【23HS8430 Nema23 Stepper Motor】Nema23 57 type;Step Angle: 1.8°; Current: 3.0A; Holding torque: 180N. 4× 23HS8430 Nema23 stepper motor 76mm 270oz-in 3A ... more1.8°. 23HS8430 Nema23 stepper motor. Suitable for Nema17 Nema23 two-phase/four-phase/four-wire/six-wire stepper motors which currently within 4.2A.
Buy It Now
Free Shipping Condition: New Location: China Maximum current: 25A. Generally, the motor with Hall has 8 wires (applicable), and the motor without hall has only 3 wires. Note: The drive module is ... morebare board, and it is not necessary to force heat dissipation to drive the motor with power below 100W, as long as normal ventilation is ensured.
Buy It Now
Free Shipping Condition: New Location: Edmond, United States 140Pcs U Shape Shield Solderless Breadboard Jumper Cable Wire Kit Arduino Shield. This is a pulse module, which can provide 2.52.5khz--6868 kHz frequency, ... morestepping drive power signal. If you want to change the frequency range, you can change the C46 capacitor.
Buy It Now
$129.95 Shipping Condition: New – Open box Location: Hawthorne, United States NEW OUT OF BOX! Motion Planner. Pocket Motion Planner. TM or Pocket Motion Planner. 6 programmable outputs, 2 D/A monitor outputs, 1 relay output. Two ... moreserial communication ports: one RS232 port (3 wire) and one RS232/RS485 port (4 wire).
Buy It Now
Free Shipping Condition: New Location: Glendora, United States L298N as main chip, ST corporation production. Chip: L298N (ST NEW). Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. ... moreMini Tap & Die Wrench Kit M1 M1.1 M1.2 M1.4 M1.6 M1.8 M2 M2.2 M2.5 30PCS/Set USA.
Buy It Now
Free Shipping Condition: New Location: United States 4, can produce pulse signal, can also produce PWM signal, can choose the jumper. PUL=PULS=CLK Pulse. EN=ENA=FREE Enable. DIR=CW=CWW Direction. DIR+ connect ... moreDIR. Product View.
Buy It Now
Free Shipping Condition: New Location: United States PWM REGULATION: This motor drive module adopts PWM speed regulation and is widely used in printers and robots with power indicator lights, etc. Product ... moreMaterial: Copper Clad Laminate. Feature: 1. Item Type: DC Motor Drive Module.
Buy It Now
Free Shipping Condition: New Location: Fort Collins, United States Want more than one A4988 module?. A4988 Stepper Motor Driver Module Specifications 1 x A4988 Stepper motor driver module. This driver moduleprovides five ... moredifferent step resolutions: Full-step, 1/2, 1/4, 1/8 and 1/16 step.
Buy It Now
$3.75 Shipping Condition: New Location: China If you only need the motor to start and stop, connect to high level to start and low level to stop. High level 2-9V is all right, low level is suspended ... moreor grounded. Powerful protection functions, over-current protection and over-heat protection, all achieve protection by limiting the drive current.
Buy It Now
$3.00 Shipping Condition: New Location: China When the drive motor, the module maximum rated current up to 100A, and conduction only 0.0015 ohm resistor. Large heat sink at high currents can effectively ... moredrive module for cooling, maintain good and stable performance of the module.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China 1 x 5Axis Mach3 Breakout Board & USB Cable. Stepper Motor & Driver. motor with VFD kits, servo motor and servo drive kits, stepper motor and stepper drive ... morekits, ball screw. CNC Spindle Motor & Tool Parts.
Buy It Now
$10.95 Shipping Condition: New Location: Spring Hill, United States Gecko G540 Overview Part 1 Users Manual Breakdown - YouTube. How To Change A Fuse, Or A Drive In A Gecko Drive G540 - YouTube. Here's an overview on the ... moredrive covered from Marcus application engineer at Gecko Drive.
Buy It Now
$17.46 Shipping Condition: Used Location: Sanford, United States The DM Series can be operated in either a position, velocity or torque mode. In the position mode the drive accepts step and direction input. DM Series ... more— Best Accuracy and Repeatability! • Brushless direct drive motor with 10 foot cable.
Buy It Now
$16.10 Shipping Condition: Used Location: Sanford, United States The DM Series can be operated in either a position, velocity or torque mode. In the position mode the drive. DM Series — Best Accuracy and Repeatability! ... more• Brushless direct drive motor with 10 foot cable.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Specification Bracket: Material: Aluminium Rod, Plastisol Propeller Color: Black and Silver Drive Rod Length: 56cm/22.05inch Small Bracket Size: 19*8cm/7.48*3.15inch ... moreControl Lever Length: 53cm/20.87inch Package Size: 94*19*16cm/37.01*7.48*6.30inch Net Weight: 4.7kg/10.
Buy It Now
$19.00 Shipping Condition: New Location: United States Bracket: Material: Aluminium Rod, Plastisol Propeller. Do You like Fishing on the River?. Do You Want to Go Boating with Your Family?. but Are You Worried ... moreAbout the Manual Boating Is Too Tired?. with Our Fishing Boat Engine, You Don't Have to Worry About This Problem.
Buy It Now
Free Shipping Condition: New – Open box Location: Ocala, United States Item Stepper drive. step and direction. Drive Features Self-test, anti-resonance (electronic damping) and command signal filtering. Tuning Mode Pre-tuned ... moreper motor. Command Signal(s). Technical Attributes.
Buy It Now
Free Shipping Condition: New Location: Charlotte, United States The driver board can drive hard disk brushless motors ,CD-ROM brushless motor and so on ， the micro 3-wire or 4-wire. without hall brushless motor . Speed ... moreadjust :0%-100%. Material: Plastic and Electrical components.
Buy It Now
$3.20 Shipping Condition: New Location: China Features: This driver is a low-power fan brushless drive, and can also be embedded in other systems. There is motor blocking protection during normal ... moreoperation. Matching use of three-phase DC brushless motors with equivalent current and power.
Buy It Now
Free Shipping Condition: New Location: Milner, United States 2pcs USA L298 L298N H-Bridge DC Motor Stepper Servo Drive Driver Arduino Raspberry Pi. These are motor driver boards - drive up to 2 DC motors or one ... morecommon stepper motor.
Buy It Now
Free Shipping Condition: New Location: Sallisaw, United States L293D motor drive shield expansion board is a commonly used DC motor drive module, using 293D chip small current DC motor driver chip. Up to 4 bi-directional ... moreDC motors with individual 8-bit speed selection (so, about 0.5% resolution).
Buy It Now
$2.99 Shipping Condition: New Location: China Dual DC Stepper Motor Drive Controller Board Module TB6612FNG Replace L298N Description: Description: The TB6612FNG motor driver can control up to two ... moreDC motors at a constant current of 1.2A(3.2A peak) Two input signals(IN1 and IN2) can be used to control the motor in one of four function modes- CW. CCW, short-brake, and stop. The two motor outputs(A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode.CJMCU. Logic supply voltage(VCC) can be in the range of 2.7-5.5VDC. While the motor supply(VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel(or up to 3.2A for a short. Single pulse) Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other. Features: Power supply voltage: VM=15V max. VCC=2.7-5.5V•Output current: Iout=1.2A(average) 3.2A(peak) Standby control to save power•CW/CCW/short brake/stop motor control modes•Built-in thermal shutdown circuit and low voltage detecting circuit•All pins of the TB6612FNG broken out to 0.1" spaced pins•Filtering capacitors on both supply lines Feedback: We will leave 5 Star psitive Feedback after receiving the payment.5 Star Feedback is our life. Please help do not leave a neutral or negative feedback and Low score. Please do contact us to get a better solution! Your understanding will be appriciated! We believe all the problems can be solved if buyer works with us I am a honest seller. Please 100% trust! Your sasifation is our final goal! Our best service will let you 100% satisfy! Hope also to receive your 5 star positive feedback! Note: The economy shipping will be no tracking number. Only have the recording number to prove it sent If you need the track
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China CNC 2012 Latest Advanced 3Axis TB6560 Stepper Drive Controller With Box 0.5-3.5A More. NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller With Aluminium ... moreBox(0.5A-3.5A) Product Features: Adopt Original Toshiba TB6560AHQ chip- High power. Maximum 3.5A drive current chipset! Adjustable"0.5A-3.5A(Peak Current) Drive Current Settings: the ouput current of actual operation on each axis can be set to"20% 50% 75% 100% of the Maximum Current. Adjustable Subdivision(Micro Step) Settings: 1. 1/2, 1/8, 1/16. Adjustable Decay Mode Settings(4 modes) I. 0% No Decay Mode; II. 25% Slow Decay Mode; III. 50% Mid Decay Mode; IV. 100% Fast Decay Mode. Automatic Semi-flow Control Function: adjustable semi-flow mode and adjustable semi-flow current. With multiple semi-flow model and semi-flow current settings. With New-type Bipolar constant current chopping technology: High working precision. Low vibration, Low noise. Professional design with super anti-jamming function for steadier running. Overload. Overheat Protection Function: Protect the Computer, Driver board and other equipments from being damaged. Cooling Aluminium box Design: Cooling function and Protect the driver board from being damaged by dirt. Dust or other liquids. Full closed-type optical isolation(Formal Photoelectric Coupler) to protect the user's computer and equipment Standard parallel interface. Supports software MACH2, MACH3( Default Software we recommend) EMC2, KCAM4 etc. For compatibility with other softwares. Please feel free to contact us! Application Field: For processing various pattern mould. For advising. Such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc. For carving portrait. Scenery, handwriting, sealing, etc. Suitable for any small-and-medium automatic equipment with CNC controller. Such as X-Y-Z tables, labeling machines, laser cutters, engraving machines, and pick-place devices. Dip settings: Current Settings S1 S2 S3 S4 Micro Step Settings S5 S6 Decay Mode S
Buy It Now
Free Shipping Condition: New Location: Fremont, United States ● Manufacture Part Number: DM2282. 1 x Digital Stepper Motor Driver. NEW HP EliteBook 840 850 820 845 855 G3 G4 Hard Drive Caddy Bracket Screws. We will ... moreprovide you the best products and service. Hard Drive Caddy Screw G1 G2 NO-G3 Fit for HP EliteBook 840 850 740 750 745 755.
Buy It Now
Free Shipping Condition: New Location: Brentwood, United States This module USES L298N as the main drive chip, with strong driving ability, low heat and strong anti-interference ability. This module USES a large capacity ... morefilter capacitance, a continuation protection diode, can improve reliability.
Buy It Now
$129.95 Shipping Condition: New – Open box Location: Hawthorne, United States NEW OUT OF BOX! Motion Planner. Pocket Motion Planner. TM or Pocket Motion Planner. 6 programmable outputs, 2 D/A monitor outputs, 1 relay output. Two ... moreserial communication ports: one RS232 port (3 wire) and one RS232/RS485 port (4 wire).
Buy It Now
Free Shipping Condition: New Location: United States L298N as main chip, ST corporation production. Chip: L298N (ST NEW). Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. ... moreNew M3-M8 T-Handle Ratchet Tap Wrench Machinist Tool +5Pcs Screw Thread Plug Tap.
Buy It Now
Free Shipping Condition: New Location: China Product Name: 1pcs Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino Basic Attributes Name Double H Bridge Motor Driver Module ... moreWorking mode Drived by H bridge(double lines) Control chip L298N? ST? Logical voltage 5V Driving voltage 5V? 35V Logical current 0mA-36mA Driving current 2A(MAX single bridge) Storage temperature? 20? +135? Maximum power 25W weight 30g Periphery dimension 43*43*27mm Product features: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Real figure? L298N is a kind of high voltage.High current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V)large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well. Port function? Circuit principle diagram? This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V. It can enable the on
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New – Open box Location: Santa Clara, United States Encoder input and 3 limit switch inputs per axis. axis, carrying out all motion in parallel. circle primitives. • One high speed differential quadrature ... moreencoder input, one single-ended. New open box - only took it out to power up, take pictures and update the FW to latest version.
Buy It Now
$2.00 Shipping Condition: New Location: Jamaica, United States Chip:LMD18200T motor driver chip. LMD18200T chip itself can overheat or overcurrent protection. Maximum output power: 75W. Maximum output current: 3A ... more(instantaneous peak current 6A). The chip used in this product is an H-bridge assembly dedicated to DC motor drive.
Buy It Now
$3.40 Shipping Condition: New Location: China Product Name: 1pcs Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino Basic Attributes Name Double H Bridge Motor Driver Module ... moreWorking mode Drived by H bridge(double lines) Control chip L298N? ST? Logical voltage 5V Driving voltage 5V? 35V Logical current 0mA-36mA Driving current 2A(MAX single bridge) Storage temperature? 20? +135? Maximum power 25W weight 30g Periphery dimension 43*43*27mm Product features: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Real figure? L298N is a kind of high voltage.High current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V)large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well. Port function? Circuit principle diagram? This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V. It can enable the on
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Stepper Motor Driver TB6600 4A DC9-40V for Nema17 Nema23 Nema34 42 / 57 / 86mm Specifications& Feature： Signal input: single ended, pulse / direction ... moreSubdivision optional: 1/2/4/8/16/32 subdivision Output current: 0.5A-4.0A Input voltage: 9-42VDC (recommends 12-30V) The current is automatically halved at rest. Can drive 4, 6 and 8 Lead two-phase, four-phase stepper motor Optocoupler isolated signal input, strong anti-interference ability With overheating, overcurrent, undervoltage lockout, input voltage anti-reverse protection and other functions Small size, easy to install External signal 3.3-24V universal, no series resistor required Operating Temperature: -10 to 45 Degrees Celsius Storage temperature: -40 to 70 Degrees Celsius Chopping Frequency: less than 50KHZ.
Buy It Now
$60.90 Shipping Condition: Used Location: Rancho Cucamonga, United States
Buy It Now
Free Shipping Condition: New Location: China 1pcs x HBS57 Stepper Motor Drive. Drive Model: HBS57 (Nema 23, for 57 stepper motor). Details of Stepper Drive HBS57. 3pcs x 57 Integrated Servo Motor ... more180W 3000rpm. 57 Integrated Servo Motor 180W 3000rpm.
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Features: 1. 100% brand new and high quality. 2. Bipolar constant current chopper 3. High-speed optocoupler signal isolation input 4. Electrical input ... moresignal is TTL compatible 5. Stationary current is automatically reduced by half 6. Suitable for any small-and-medium automatic equipment with CNC controller, such as X-Y-Z tables, labeling machines, laser cutters, engraving machines, and pick-place devices. 1. 9V-42V DC power supply 2. H bridge bipolar constant phase flow drive 3. the maximum 4.0A of the eight kinds of output current 4. the largest 32 subdivision of the 6 models are optional 5. input signal high speed photoelectric isolation 6. common-anodestandard single pulse interface 7. offline to maintain the function 8. semi closed enclosure can be adapted to a more stringent environm.
Buy It Now
Free Shipping Condition: New Location: Suffern, United States Input: 1-5A Current, Select Drive Stepper Motor. ERR: Red Light, Power, Indicator Light, Power Indicator. The half-flow function is a 200ms step pulse, ... moreand the driver output current is automatically reduced to 50% of the rated output current to prevent motor heating.
Buy It Now
Free Shipping Condition: New Location: United States The mode needs to be set in [F5-F8] function. Feature: 1. This module has no programmable function, but built in a variety of fixed operation mode, the ... moreuser can quickly choose the appropriate trajectory.
Buy It Now
$19.95 Shipping Condition: New Location: Wheelersburg, United States They have the added filter capacitor on the sense lines. It has the trim pots located closer to the openings. The G540 is a complete 4-axis system which ... moreplugs directly into your computer via the parallel port and to your motors through DB9 connectors.
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Signal input: single ended, pulse / direction Subdivision optional: 1/2/4/8/16/32 subdivision Output current: 0.5A-4.0A Input voltage: 9-42VDC (recommends ... more12-30V) The current is automatically halved at rest. Can drive 4, 6 and 8 Lead two-phase, four-phase stepper motor Optocoupler isolated signal input, strong anti-interference ability With overheating, overcurrent, undervoltage lockout, input voltage anti-reverse protection and other functions Small size, easy to install External signal 3.3-24V universal, no series resistor required Operating Temperature: -10 to 45 Degrees Celsius Storage temperature: -40 to 70 Degrees Celsius Chopping Frequency: less than 50KHZ.
Buy It Now
$3.20 Shipping Condition: New Location: China L298N as main chip, ST corporation production. Chip: L298N (ST NEW). Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. ... moreHigh working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Stepper Drive TB6600. In the user expects low cost, high current operation. Stepper Motor Drive System. Can drive 4, 6 and 8 Lead two-phase, four-phase ... morestepper motor. CNC Machine Parts. 3D Printer. Servo Motor Drive System.
Buy It Now
$10.00 Shipping Condition: New Location: Chino, United States 🚤Specifications Material: Aluminum Alloy, Stainless Steel, Copper, Iron, Plastic Surface Treatment: Painting Color: Black, Silver Voltage: 12v Maximum ... morePower: 635w Speed: 1800rmp Maximum Load-bearing Capacity: 500-600kg/1102-1322.7lbs Operation Mode: Electric Battery Cables Length: 1.3m/4.3ft Net Weight: 10.5kg/23.15lbs Gross Weight: 12kg/26.45lbs Total Height: 1.15m/3.77ft Handle Size: 50cm/19.69inch Propeller Size: 28*9cm/11.02*3.54inch Package Size: 117*17*39cm/46.06*6.7*15.35inch 🚤Package Included 1* Electric Trolling Motor 1* Three-blade Propeller All Accessories for Assembly.
Buy It Now
$8.45 Shipping Condition: Used Location: Lebanon, United States
|
|
|
 |