|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
$3.50 Shipping Condition: New Location: China Description The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. The module has ... morea pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting. Overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) 1）Simple step and direction control interface 2）Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 3）Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 4）45 V maximum supply voltage 5）Built-in regulator(no external logic voltage supply needed) 6）Can interface directly with 3.3 V and 5 V systems 7）Over-temperature thermal shutdown. Over-current shutdown, and under-voltage lockout 8）Short-to-ground and shorted-load protection 9）4-layer. 2 oz copper PCB for improved heat dissipation 10）Exposed solderable ground pad below the driver IC on the bottom of the PCB 11）Module size. Pinout, and interface match those of our A4988 stepper motor driver carriers in most respects(see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet(1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil(see the Power Dissipation Considerations section below for more information) Here are some of the driver’s key features: Simple step and direction control i
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States The NANO Motor Shield is based on the L298P, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping ... moremotors. L298P, Drives 2 DC motors or 1 stepper motor.
Buy It Now
Free Shipping Condition: New Location: Plainville, United States This L298N Motor Driver Module is a high-power motor driver module for driving DC and Stepper Motors. This module consists of an L298 motor driver IC ... moreand a 78M05 5V regulator. Driver chip: L298N dual H-bridge driver chip.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China L298N Dual H Bridge DC stepper Motor Driver Controller module Board for Arduino. Principle diagram: Features: Driver: L298N Dual H Bridge DC Motor Driver ... moreIC The terminal supply area of driven part Vs: +5 V ~ +35 V; such as the need to take power within the board. The supply area Vs: 7V ~ 35V The peak current of driven part Io: 2A the terminal supply of area the logical part Vss: +5 V ~ +7 V(can take power within the board +5 V) the operating current range of the logical part: 0 ~ 36mA control signal input voltage range: Low:0.3V ≤ Vin ≤ 1.5V High: 2.3V ≤ Vin ≤ Vss enable signal input voltage range: Low: 0.3 ≤ Vin ≤ 1.5V(control signal is invalid) High: 2.3V ≤ Vin ≤ Vss(control signal active) Maximum power consumption: 20W(when the temperature T = 75 °C) Storage temperature: 25 °C ~ +130 °C Driver Board Size: 55mm* 49mm* 33mm(with fixed copper pillar and the heat sink height) Driver Board Weight: 33g Other Extensions: control of direction indicators. The logic part of the plate to take power interface. X-058. ● We only accept paypal payments. ● When we receive your payment. We will be help you arrange shipping in 2 working days. Weekends and holidays do not break) ● All our parcels are shipped via China Post.Can provide Following two Delivery mode： Airmail It takes about 15-25 days EMS(Express Mail Service) It takes about 7-14 days ● Buyer should expect to pay any amount charged by the government of bidder's country; this includes but not limited to duty& tax ● Shipping& handling fees are non-refundable. ● If you haven’t received the item in one month. We will refund to you.PLEASE INSPECT YOUR ITEMS WHEN THEY ARE RECEIVED） ● Once you receiving the item with satisfaction. Please leave us positive feedback, and 5 STAR DSR. Thank you! ● If you feel dissatisfied with the products receive. Please could you should first contact us using e-mail. Please do not impulsively give a Neutral or Negative feedback before giving us the opportunity to resolve you problem! Neutral and Negative feedback wi
Buy It Now
Free Shipping Condition: New Location: China Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: Stepper motor driver board with ULN2003. For 12V 5V Stepper motor A. B, C, D four-phase LED indicates the status of the stepper motor work. Stepper motor with a standard interface. When used directly pluggable. Drive Module Board Size:2.8cm x 2.8cm x 2cm Package: 1PCS X ULN2003 Stepper Motor Driver Board Module for Arduino We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The arrival time is 5-20 business days to United States usually. We ensure dispatch the item within 1-2 business days. However. You bought the item from opposite side of the earth, so it needs a little longer time to deliver. Please place order only if you agree with the shipping time and all the
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States 10x A4988 Stepper motor driver module. Link to online operation and programming Instructions. 10x Heatsink. Microstep resolutions: Full, 1/2, 1/4, 1/8 ... moreand 1/16. Load short-circuit protection.
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States 10x A4988 Stepper motor driver module. Thermal shutdown circuitry. Load short-circuit protection. Ground fault protection. Microstep resolutions: Full, ... more1/2, 1/4, 1/8 and 1/16. Maximum current per phase: 2A (with cooling).
Buy It Now
Free Shipping Condition: New Location: China Delivery Details 1.Standard shipping carrier is ePacket with tracking code for United States address.Delivery within 7-14 busienss days. 2.For outside ... moreUS address.Standard shipping carrier is Hong Kong Post without tracking code,delivery within 25-30 business days.We provide a free tracking for order above 45USD.Please contact us if you want to add a tracking code for small orders. 3.Express shipping like DHL.Fedex,UPS,TNT is also avaiable if you are willing to pay extra.DHL is our standard shipping carrier for Expedited shipping,please contact us if you want a different carrier. 4.Customs duties or taxes are buyer's resposibility for all of the listings.Please check with your local customs office if you have any doubts. 5.Please confirm you are putting a correct and complete shipping address here.You are resposible for extra charge if your package been returned because of wrong address. Description The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) Features Simple step and direction control interface Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates 45 V maximum supply voltage Built-in regulator(no external logic voltage supply needed) Can interface directly with 3.3 V and
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States 10x A4988 Stepper motor driver module. Thermal shutdown circuitry. Load short-circuit protection. Ground fault protection. Microstep resolutions: Full, ... more1/2, 1/4, 1/8 and 1/16. Maximum current per phase: 2A (with cooling).
Buy It Now
Free Shipping Condition: New Location: Lexington, United States 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino PI PIC Raspberry Pi 💎【28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board】:A, ... moreB, C, D four-phase LED indicates the status of the stepper motor work.
Buy It Now
$1.99 Shipping Condition: New Location: China Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: Brand new and high quality Voltage: 5V Diameter: 28mm Step angle: 5.625 x 1/ 64 Reduction ratio: 1/ 64 5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for. supporting the use of a direct plug and easy to use stepper motor used in the development board. Stepper motor driver board with ULN2003 A. B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface. When used directly pluggable Original box: NO Length: 274mm Net weight: 43g Package: 1 x Drive Module Board ULN2003 1 x Stepper motor 28BYJ-48 12V We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. Instead of using a latch ... moreand the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard.
Buy It Now
$3.50 Shipping Condition: New Location: China Description Brand new and high quality. The EasyDriver is a simple to use stepper motor driver. Compatible with anything that can output a digital 0 to ... more5V pulse(or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver) MS1 and MS2 pins broken out to change microstepping resolution to full. Half, quarter and eighth steps(defaults to eighth) Compatible with 4. 6, and 8 wire stepper motors of any voltage. Adjustable current control from 150mA/phase to 750mA/phase. Power supply range from 7V to 30V. The higher the voltage. The higher the torque at high speeds. Size: 4.8cm x 2cm. Note: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC. Package Included: 5PCS x A3967 Stepping Motor Shield Driver Shipping Terms, 1. WORLDWIDE Free SHIPPING. Except China) 2. Orders processed within 24 hours of payment verification. 3. We only ship to confirmed eBay addresses. Your eBay address MUST MATCH your Shipping address. 4. The images shown are not the actual item and are for your reference only. 5. SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary. Particularly during the holiday season. 6. If you have not received your shipment within 30 days from payment. Please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 7. Due to stock status and time differences. We will choose to ship your item from our first available warehouse for fast delivery. No Tracking Number The shipping cost is very low.We are not responsible for any loss in the mail if the item not insured(no-registered mail) Registered Post Shipping cost: Would better to Add 3 USD to Upgrade- Registered Post(Choose"Standard Int'l Shipping" for one item.And others choose free shipping.we can send all your items in one box with tracking number. Express Courier Need URGENT? We offer a varienty of shipping methods(Expedited Int'l Shipping) to meet your ne
Buy It Now
$13.88 Shipping Condition: Brand New Location: Cairns, Australia The module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor. 800mA continuous current output capability per channel. Specifications ... moreLow static work current. Each channel has 800mA continuous current output.
Buy It Now
Free Shipping Condition: New Location: China Stepper motor driver board with ULN2003. Stepper motor with a standard interface, when used directly pluggable. A, B, C, D four-phase LED indicates the ... morestatus of the stepper motor work. Drive Module Board Size:2.8cm x 2.8cm x 2cm.
Buy It Now
Free Shipping Condition: New Location: Matthews, United States Item Description: Onboard two the L9110S motor control chip(Original) the module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor, ... morethe module input voltage:2.5-12V, the 800mA continuous current output capability per channel, 1. Low static work current 2. Power supply voltage: DC2.5-12V 3. Each channel has 800mA continuous current output 4. Low saturation pressure drop 5. TTL/CMOS output level compatible. Can be connected directly to the CPU 6. Output built-in clamping diode. Apply to the perceptual load 7. Control and drive integrate in IC 8. Have pin high pressure protection function 9. Working temperature: 0-80 ℃ 10.Size:29.2(mm)x23(mm) test code: include sbit MOTOR_A_1 = P0 ^ 0; sbit MOTOR_A_2 = P0 ^ 1; sbit MOTOR_B_1 = P0 ^ 2; sbit MOTOR_B_2 = P0 ^ 3; void delay(unsigned long cnt) while(cnt- void forward(void) MOTOR_A_1 = 1; MOTOR_A_2 = 0; MOTOR_B_1 = 1; MOTOR_B_2 = 0; void backward(void) MOTOR_A_1 = 0; MOTOR_A_2 = 1; MOTOR_B_1 = 0; MOTOR_B_2 = 1; void main(void) EX0 = 1; EX1 = 1; EA = 1; while(1) forward( delay(30000) backward( delay(30000) Dear my friend. We also support wholesale if need more. Please give us message. We will give u more discount: Shipping: 1. Item will be shipped within 1- 2 business days. 2. Delivery Time: Via Express: Generally 3-15 working days. Need to pay more money if you need to express. Via Air Mail: Generally 15-30 working days. Sometimes, it will take 35~50 days. Usually we will send it to USA via USPS. It’ s need 8-15 days. Other country will be via Via Air Mail. 3. If you have not received your shipment within 30 days from payment. Please contact us. We will track the shipment and get back to you as soon as possible with a reply. 4. Buyer responses for(in case) all tax or VAT under any circumstances. We will do our best to minimum the risk.We are not responsible for any problems caused by the customs of buyer's country. Feedback& Dispute If any issue or troubles. Please contact us before you make negative feedback
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Can drive 4 DC motors, or two 4-wire 2-phase stepping motor. hope you could understand.
Buy It Now
Free Shipping Condition: New Location: Lincoln, United States Description: Step Motor: Diameter: 28mm Voltage: 5V Step angle: 5.625 x 1/64 Reduction ratio: 1/64 5 lines cable 4 phase stepper motor can be driven by ... moreuln2003 chip. It also can be connected as 2 phase to use. ULN2003 Step Motor Driver Board: A. B, C, D LED indication Four-phase stepper motor work status· Size: 31x35mm Package includes: 1. 1* Stepper Motor 2. 1* ULN2003 Driver Board
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States DRV8825 Driver Module. A4988 Driver Stepper Driver Carrier Board. Ground Fault Circuit. Load short-circuit protection. Synchronous rectification for low ... morepower dissipation. hope you could understand.
Buy It Now
$2.80 Shipping Condition: Neu: Sonstige (siehe Artikelbeschreibung) Location: China High-current 43A. Able to reverse the motor forward, two PWM input frequency up to 25kHZ;. Screw sheild. OLED LED&RGB. Double BTS7960 large current (43 ... moreA) H bridge driver;. Am 11.01.2023 hat der Verkäufer die folgenden Angaben hinzugefügt.
Buy It Now
$3.20 Shipping Condition: New Location: China Can drive 4 DC motors, or two 4-wire 2-phase stepping motor. hope you could understand. Product Details.
Buy It Now
$2.41 Shipping Condition: Brand New Location: China 1 x ULN2003 Stepper Motor Driver Board Module Arduino 5V 4-phase 5line 28BYJ48. DC Resistance: 200ω±7% (25℃). Insulation Resistance: >10Mω (500V). Noise:
Buy It Now
$4.00 Shipping Condition: New – Open box Location: Greenville, United States Chip L298N (ST NEW). 3D PRINTER CNC. Uses large capacity filter capacitor to protect diodes and improve the reliability. Board for CNC / Arduino. Double ... moreH bridge drive. Drive current 2A(MAX single bridge).
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States The drive current: 2A (best to install the heat sink).
Buy It Now
Free Shipping Condition: New Location: Katy, United States Features: L293D is a monolithic integrated. High voltage, high current, 4-channel driver.Basically this means using this chip you can use DC motors and ... morepower supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor. 2 interface for 5V Servo connected to the high-resolution dedicated timer- no jitter! Can drive 4 DC motors or 2 stepper motors or 2 Servo Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors(unipolar or bipolar) with single coil. Double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A(1.2A peak current) with thermal protection. Can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up reset button 2 external terminal power interface. For seperate logic/motor supplies Tested compatible for Mega. Diecimila& Duemilanove Package Included: 1 x Motor Drive Shield Expansion Board L293D Module Arduino Duemilanove Mega2560 UNO Payment Policy 1. We ONLY accept payment via PayPal. Other payment is not acceptable. 2. If you do not have PayPal account. Please registered through http:www.paypal.com/ before you bid our item. Please check the total price of the item before you bid the product. If you puy two. There is no discount for the combined shipping. 3. If you pay with e-check normally general takes 5 business days to clear. Once your eCheque payment clears. Your item will be dispatched within one working days. 4. All payments must be made within 7 days after you won the bid. Color information 1. We work very hard to provide the best representation of style and the color of the product through our photographs and descriptions. 2. As the Buyer it is your responsibility to read and understand the color description as that is color of the item you are pu
Buy It Now
$3.20 Shipping Condition: New Location: China The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder ... moreSJ2 closed on the EasyDriver). EasyDriver drives bi-polar motors, and motors wired as bi-polar.
Buy It Now
$3.40 Shipping Condition: New Location: China Chip L298N. Double H bridge drive. Drive current 2A(MAX single bridge). 5 x Double H bridge driver. Storage temperature -20℃ to +135℃.
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Adaptive motor: Stepper motor. The distance / speed / delay / number of cycles can be saved and set after power down. It can run independently as a module, ... moreor it can be used together with other systems.
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States The Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping ... moremotors. hope you could understand.
Buy It Now
Free Shipping Condition: New Location: China Cancel the drive module,use integrated imported stepper motor drive,with short circuit protection,and integrated heat dissipation aluminum alloy;. Add ... morethe fan port to force heat dissipation;. Improved USB interface: The original USB interface is patch soldering, transport collision and improper use, easy to drop, now changed to plug-in, very strong;.
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States The drive current: 2A (best to install the heat sink). 10 Heatsink.
Buy It Now
Free Shipping Condition: New Location: Matthews, United States 2pcs Stepper Motor+ Driver Board ULN2003 5V 4-phase 5 line. Product information Brand new and high quality Voltage: 5V Diameter: 28mm Step angle: 5.625 ... morex 1/ 64 Reduction ratio: 1/ 64 5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for. supporting the use of a direct plug and easy to use stepper motor used in the development board. Stepper motor driver board with ULN2003 A. B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface. When used directly pluggable. Original box: NO Color: Black Length: 274mm Package Includes 2x Stepper motor 2x ULN2003 Driver board. Payment. Payment. Payable To. Note. PayPal All payments are due within 7 days of the close of auction. Failing to do so. Non-paying bidders will be reported to eBay. Shipping Policy. Delivery Time. We ship to worldwide. It usually takes 10-30 Business Days to delivery. Shipping address. We ship to your PayPal address. Please. Make sure to provide us with correct, precise, and detailed shipping Address. Send Time. Items will be shipped within 1 to 3 business days upon payment received or cleared. Note. If you don't receive items over 30 business days. Please notify us via eBay message. Return Policy. We appreciate your business and offer an instant 7 days return policy.7 days after receive the item) The returned item has to be in its original condition. We are able to refund your money without shipping cost. Contact us. For anything about product. Price, shipping or order status, please contact us via eBay message. We love positive feedback and 5 scores DSR. We will leave it for everyone that leaves it for us.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
$1.98 Shipping Condition: Brand New Location: China Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: Brand new and high quality Voltage: 5V Diameter: 28mm Step angle: 5.625 x 1/ 64 Reduction ratio: 1/ 64 5 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2 development board used for. supporting the use of a direct plug and easy to use stepper motor used in the development board. Stepper motor driver board with ULN2003 A. B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface. When used directly pluggable Original box: NO Length: 274mm Net weight: 43g Package: 1 x Drive Module Board ULN2003 1 x Stepper motor 28BYJ-48 12V We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States Able to reverse the motor forward, two PWM input frequency up to 25kHZ;. Double BTS7960 large current (43 A) H bridge driver;. Just need four lines from ... moreMCU to driver module (GND. two heat flow passing through an error signal output;. ).
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States Able to reverse the motor forward, two PWM input frequency up to 25kHZ;. can solder heat sink;. Double BTS7960 large current (43 A) H bridge driver;. ... more5V power indicator on board;.
Buy It Now
Free Shipping Condition: New Location: China And integrated heat dissipation aluminum alloy. add the fan to force heat dissipation. The stepper motor drive increases the self-recovery fuse. Improved ... moreUSB interface: The USB interface is patch soldering, transport collision and improper use, easy to drop, now changed to plug-in, very strong.
Buy It Now
$2.99 Shipping Condition: New Location: China Store Category Description Motor Features: Rated Voltage: DC5V 4-phase Step angle: 5.625 x 1/64 DC Resistance: 200Ω±7% 25C) Insulation Resistance: ... more10MΩ(500V) Dielectric Strength: 600V AC/ 1mA/ 1s Insulation Grade: A No-load Pull in Frequency: 600Hz No-load Pull out Frequency: 1000Hz Pull in Torque: 34.3mN.m(120Hz) Detent Torque: 34.3mN.m Temperature Rise: Noise: Cable length:23.5CM ULN2003 Driver Board: A. B, C, D four-phase LED indicates the status of the stepper motor work. Stepper motor with a standard interface. When used directly pluggable. Drive Module Board Size:2.8cm x 2.8cm x 2cm. Package included 5pcs stepper motor 5pcs ULN2003 Driver board Hotsale Payment We accept payment via Paypal. Shipping Shipping to USA 11- 20 days, Refund time:25 days Shipping to Europe 15- 30 days, Refund time:35 days Shipping to Canada.Australia 15- 30 days, Refund time:35 days Shipping to Italy.Brazil,Israel 25- 40 days, Refund time:45 days Shipping to other countries 20- 30 days, Refund time:35 days About tracking number. Cause we sell the items at low price.So if you buy items less than 20usd,we have no tracking number,otherwise,if you buy items more than 20usd,we will send them with a free tracking number. If package not received.What you should do? We list all shipping time to the worldwide as above.Cause we are from china,it is international shipping,so packages take much time to arriveIf you don't receive the package in the time as we write,please contact us before you leave negative feedback and open the case.We are honest and professional seller,we will contact the post office in time after you contact us, if we confirm that the package are lost during the shipping,we will refund your full payment or send you another package at once.Hope your understanding and cooperation. Copyright © 2013 goldpart. All rights reserved
Buy It Now
Free Shipping Condition: New Location: China L9110S Dual DC motor Driver Controller Board. Description 1. Double L9110S chip motor driver chip 2. Power supply voltage: 2.5V- 12V 3. Suitable motor ... morescope: motor working voltage of 2.5 v to 12 v. 0.8 A maximum working current. 4. Can drive two DC motors at the same time. Or 1pcs Phase 4 line 2 type stepping motor. 5. PCB size: 2.8 cm* 2.1 cm super small volume. Suitable assembling. 6 Set fixed mounting holes. Diameter: 3 mm Interface specification: 6 p black bending row needles explain】 VCC— external 2.5 V to 12 V voltage GND— external GND IA1— external microcontroller IO port IB1— external microcontroller IO port IA2— external microcontroller IO port IB2— external microcontroller IO port. 4 p green terminal instructions】 OA1 OB1 connecting DC motor 2 pin. No direction OA2 OB2 connecting DC motor 2 pin. No direction. Directions for use Connecting VCC. GND module power indicator lighting IA1 input high level. IA1 input low level, OA1 OB1】 motor forward; IA1 input low level. IA1 input high level, OA1 OB1】 motor reverse; IA2 input high level. IA2 input low level, OA2 OB2】 motor forward; IA2 input low level. IA2 input high level, OA2 OB2】 motor reverse. Packing List: 2Pcs L9110S Dual DC motor Driver Controller Board Module Payment 1.We accept Paypal only. 2.Please confirm your ebay shipping address is exact after payment. 3.If your purchased is more than £30.00. Please offer your phone number with shipping address. Delivery details 1.All item will be shipped by Airmail post within 1 business days. It takes approximately 15-25 days(USA.CA,AU,UK,DE)other country 15-35 days. 2.Express by EMS.It must add 25 USD shipping fee, it takes 5-10 workdays for delivery.If you need other Epxress(DHL,Fedex.UPS etc.please contact us to talk about shipping fee. 3.Once you purchase. Please DONOT leave negative, neutral feedback or open any case if you have not received item in 30 days, because we have mentioned the shipping time repeatedly. Contact us 新建网页 2 1.We offer retail and wholesale servi
Buy It Now
Free Shipping Condition: New Location: United States Product Name: 1pcs Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino Basic Attributes Name Double H Bridge Motor Driver Module ... moreWorking mode Drived by H bridge(double lines) Control chip L298N? ST? Logical voltage 5V Driving voltage 5V? 35V Logical current 0mA-36mA Driving current 2A(MAX single bridge) Storage temperature? 20? +135? Maximum power 25W weight 30g Periphery dimension 43*43*27mm Product features: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Real figure? L298N is a kind of high voltage.High current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V)large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well. Port function? Circuit principle diagram? This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V. It can enable the on
Buy It Now
$3.00 Shipping Condition: New Location: China The module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor. Output built-in clamping diode, apply to the perceptual load. the ... more800mA continuous current output capability per channel.
Buy It Now
$3.00 Shipping Condition: New Location: China Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. Instead of using a latch ... moreand the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard.
Buy It Now
$5.45 Shipping Condition: New Location: Wayne, United States 5Pcs A4988 Stepper Motor Driver Module for 3D Printer RepRap StepStick Arduino. Condition is New. Shipped with USPS First Class Package.
Buy It Now
$2.88 Shipping Condition: New Location: China ULN2003 Driver Board A, B, C, D four-phase LED indicates the status of the stepper motor work. Stepper motor with a standard interface, when used directly ... morepluggable. Step angle: 5.625 x 1/64. Noise:
Buy It Now
$3.00 Shipping Condition: New Location: China Product Name: 10pcs DC Stepper Motor Drive Controller Board Module L298N Dual H Bridge Basic Attributes Name Double H Bridge Motor Driver Module Working ... moremode Drived by H bridge(double lines) Control chip L298N（ ST） Logical voltage 5V Driving voltage 5V— 35V Logical current 0mA-36mA Driving current 2A(MAX single bridge) Storage temperature（ 20 ℃） +135 ℃） Maximum power 25W weight 30g Periphery dimension 43*43*27mm Product features: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Real figure： L298N is a kind of high voltage.High current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V)large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well. Port function： Circuit principle diagram： This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V. It can enable the onboard 5V lo
Buy It Now
$3.00 Shipping Condition: New Location: China Stepper motor driver board with ULN2003. 2 x ULN2003 Drive Test Module Board. A, B, C, D four-phase LED indicates the status of the stepper motor work. ... moreStepper motor with a standard interface, when used directly pluggable.
Buy It Now
$3.50 Shipping Condition: New Location: China Stepper motor driver board with ULN2003. 2 x ULN2003 Stepper Motor Drive Board Module For Arduino AVR ARM. A, B, C, D four-phase LED indicates the status ... moreof the stepper motor work. Stepper motor with a standard interface, when used directly pluggable.
Buy It Now
$3.50 Shipping Condition: New Location: China Chopping Frequency: 20KHZ. Max Drive Current: 4A. High-speed optocoupler signal isolation input. Electrical input signal is TTL compatible.
Buy It Now
$3.40 Shipping Condition: New Location: China Description This module is blue PCB now.Please know it. The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping ... morebipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting. Overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) 1）Simple step and direction control interface 2）Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 3）Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 4）45 V maximum supply voltage 5）Built-in regulator(no external logic voltage supply needed) 6）Can interface directly with 3.3 V and 5 V systems 7）Over-temperature thermal shutdown. Over-current shutdown, and under-voltage lockout 8）Short-to-ground and shorted-load protection 9）4-layer. 2 oz copper PCB for improved heat dissipation 10）Exposed solderable ground pad below the driver IC on the bottom of the PCB 11）Module size. Pinout, and interface match those of our A4988 stepper motor driver carriers in most respects(see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet(1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil(see the Power Dissipation Considerations section below for more information) Here are some of the driver’s key
Buy It Now
Free Shipping Condition: New Location: China Visit store: tinxi-clothes-shop- Import duties. Taxes and charges are not included in the item price or shipping charges. These charges are the buyer ... moreresponsibility. Please check with the local customs office to determine what these additional costs will be prior to bidding/buying. We are a company in CHINA. Delivery from China will cost approximately 20-30 working days. Please pay attention to the shipping and delivery time before you bid. Thank you. 5x High-power ULN2003 Stepper Motor Driver Board Test Module for Arduino AVR SMD. Article-Nr.5400772. Product Details: ULN2003 Stepper motor driver board Condition: New Size: approx. 31 x 35mm A. B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface. When used pluggable directly Color: show as pictures PLS NOTE that due to lighting effects. Monitor's brightness/ contrast settings etc, there could be some slight differences in the color tone of the pictures and the actual item! Package Included: 5 x Stepper motor driver board, Powered By Tinxi.
Buy It Now
$2.99 Shipping Condition: New Location: China DRV8825 Driver Module. A4988 Driver Stepper Driver Carrier Board. Ground Fault Circuit. Load short-circuit protection. Synchronous rectification for low ... morepower dissipation. Automatic current decay mode detection / selection.
Buy It Now
$2.41 Shipping Condition: Brand New Location: China 1 x ULN2003 Stepper Motor Driver Board Module Arduino 5V 4-phase 5line 28BYJ48. DC Resistance: 200ω±7% (25℃). Insulation Resistance: >10Mω (500V). Noise:
Buy It Now
Free Shipping Condition: New Location: Potsdam, United States NEW 28BYJ-48 5V ULN2003A JST Stepper Motor Driver Shield for Arduino Nano. Simple and easy to use stepper motor driver shield for 28BYJ-48 5V Unipolar ... morestepper motors. Drive up to three 28BYJ-48 5V stepper motors using powerful ULN2003A driver IC.
Buy It Now
$3.00 Shipping Condition: New Location: China Features The Motor Shield is based on the L298. Which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and ... morestepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. Operating Voltage 5V to 12V Motor controller L298P. Drives 2 DC motors or 1 stepper motor Max current 2A per channel or 4A max(with external power supply) Current sensing 1.65V/A Free running stop and brake function Click me to konw more Package Included: 1PCS* L298P Shield R3 DC Motor Driver Module 2A H-Bridge 2 way For Arduino UNO 2560 NW Similar Products $14.98 Time left:5d 19h 55m. $2.60 Time left:1d 9h 32m. $42.11 Time left:5d 20h 47m. $14.98 Time left:16d 0h 48m. $3.19 Time left:29d 10h 0m. $3.77 Time left:6d 3h 57m. $7.54 Time left:6d 3h 57m. $1.17 Time left:29d 9h 59m. $5.68 Time left:29d 10h 1m. $4.48 Time left:9d 8h 11m. $14.79 Time left:6d 0h 38m. $2.26 Time left:14d 1h 13m. $3.33 Time left:5d 19h 43m. $1.30 Time left:2d 11h 40m. $18.78 Time left:6d 3h 57m. $3.75 Time left:24d 22h 0m. $6.55 Time left:14d 1h 13m. $3.33 Time left:16d 0h 48m. $2.38 Time left:2d 11h 52m. $34.89 Time left:5d 20h 2m. $8.99 Time left:5d 19h 55m. $37.66 Time left:6d 3h 57m. $34.99 Time left:5d 19h 55m. $3.13 Time left:11d 8h 39m. $4.88 Time left:18d 9h 34m. $3.50 Time left:13d 3h 38m. $6.60 Time left:13d 3h 38m. $19.50 Time left:13d 3h 38m. $13.44 Time left:14d 1h 13m. Shipping& Handling Shipping Time: The items you ordered will be shipped out in 1-2 business day by Hong Kong Post Air Mail when your payment is clear. Payment We accept PayPal only. We only ship item to your PayPal verified address. Payment must be received within 5 Days from the date of purchase. Return Policy All the products we are selling include factory warranty. Don’t cover items that have been abused, burned and damaged in any form. Please contact us via eBay Message if you have NOT received
Buy It Now
$3.59 Shipping Condition: New Location: China Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: The EasyDriver is a simple to use stepper motor driver. Compatible with anything that can output a digital 0 to 5V pulse(or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver) EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. On this version(v4.4) we fixed the silk error on the min/max adjustment. This is the newest version of EasyDriver V4 co-designed withBrian Schmalz. It provides much more flexibility and control over your stepper motor. When compared to older versions. The microstep select(MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control. Note: Do not connect or discon
Buy It Now
$9.96 Shipping Condition: New Location: Canada
Buy It Now
Free Shipping Condition: New Location: China Instead of using a latch and the for Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This also makes it drop-in compatible with ... moreany for Arduino.
Buy It Now
$3.59 Shipping Condition: New Location: China 5pcs EasyDriver Shield stepping Stepper Motor Driver V44 A3967 for Arduino Click to Enlarge Click to Enlarge Description: The EasyDriver is a simple to ... moreuse stepper motor driver. Compatible with anything that can output a digital 0 to 5V pulse(or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver) EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. On this version(v4.4) we fixed the silk error on the min/max adjustment. This is the newest version of EasyDriver V4 co-designed withBrian Schmalz. It provides much more flexibility and control over your stepper motor. When compared to older versions. The microstep select(MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control. Note: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC. Note: This product is a collaboration with Brian Schmalz. A portion of each sales goes back to them for product support and continued development. Features: A3967 microstepping driver MS1 and MS2 pins broken out to change microstepping resolution to full. Half, quarter and eighth steps(defaults to eighth) Compatible with 4. 6, and 8 wire stepper motors of any voltage Adjustable current control from 150mA/phase to 750mA/phase Power supply range from 7V to 30V. The higher the voltage. The higher the torque at high speeds What's in the package: 5Pcs* EasyDriver Shield stepping Stepper Motor Driver V44 A3967 For Arduino Feedback: 1. If you are satisfied with our goods and service. Please leave us a positive feedback and rate the details of the transaction(Detai
|
|
|
 |