In 
 
Order by: 
Available to: 
Price: 
 - 
$
1000.00
1d 23h 1m 57s
0 bids
$60.00 Shipping
Condition: Used
Location: Belleville, United States
NO RESERVE! You're looking at a Stratasys Dimension SHDM1000 3D Printer which I think is more commonly known as the Dimension 768 BST. All parts are ... morepresent and 100% working except that the liquifier extruder nozzle clogs during printing. So it will require parts, potentially custom made parts, and expertise to get it running properly(also 1 rubber foot has been replaced with a block) Stratasys is the original company that began making FDM/FFF 3D Printers which extrude ABS plastic filament, which looks like to weed-eater line, to create 3D models. This 3D Printer uses a heated build chamber and has dual extruders, one for model material(ABS-type material) and one for break-away support material(HIPS-type material) It prints onto foam trays which are made to fit in this printer. Layer height is 0.010" or 0.013" for models. Maximum model size approx. 8" x 8" x 12" tall. When the models are finished, you would remove them from the tray and then snap off the support material, leaving you with your finished model. I have 5 other Stratasys 3D Printers; I find the models produced to be good quality and consistent, which is not always the case with the newer competing brands. I'm a mechanical engineer and I bought this machine about 2 years ago to produce models for parts I was designing. This 3D Printer has helped me tremendously and produced countless wonderful models. I have always kept the guides lubricated with the Krytox grease as recommended. At a certain point. I began experimenting with different third-party materials. The materials were of good quality ABS and HIPS resins but sometimes the filament was a bit undersized. Instead of being 1.75mm in diameter as intended, the material could be as small as 1.53mm. Apparently using undersized material can slowly damage the liquifier extruder block part over time. This is a small part inside the 3D print head, approximately 1.5" x 1" x 2" that contains a heater cartridge and little tubes that melt the plastic. I have hig
$
29900.00
Buy It Now
Condition: Used
Location: Woodinville, United States
Fuse1, SLS, SLA, FDM, 3D Printer, Powder Bed Printer, MJF, Multi-Jet Fusion, Multi Jet Fusion, Nylon 12, Nylon 11, Prototype Parts, Nylon Prototypes, ... moreSelective Laser Sintering, Stereolithography, Fused Deposition Modeling.
$
600.00
Buy It Now
$83.04 Shipping
Condition: New
Location: Venice, United States
MAKERBOT SKETCH CAT NO.: PAFW98. 1 Sketch 3D Desktop Printer. MODEL: Sketch. PRODUCT: 3D Desktop Printer. November 11 22.
$
0.99
Buy It Now
$3.00 Shipping
Condition: New
Location: China
Description Specification: Voltage: 12v Power: 40w Mater ia l: Stainless Steel Diameter: 6mm Len gth: 20mm Wire Length:1m Shipping Included: 1PCS*Cartridge ... moreHeater Recommended Products Payment We accept PayPal only. But w e only Accept your Ebay Address.Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request(e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment. Because most of orders will be processed instantly and same day dispatched. Shipping We only accept your Ebay Address.Please Make sure it's 100% right. The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The arrival time is 5-20 business days to United States usually. We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. We ensure dispatch the item within 1-2 business days. However. You bought the item from opposite side of the earth, so it needs a little longer time to deliver. Please place order only if you agree with the shipping time and all the terms below. Customs duty is obligation and liability of a citizen in your country. So buyer should be responsible for any tax and custom duty incurred. Generally. The delay or failure delivery is sometimes caused by the policy of different customs. For example, Laser Pointer is unacceptable in some countries. Therefore, please double check your local customs policy carefully before purchase. Or, we will NOT be responsible for any failure delivery related destination customs issue. Warranty and Guarantee All package need to wait 30 days.Please take care it.Less than 30 days,we can't take a refund. If the item is defect when you receive it or you are not satisfied with it. Please return it
$
175.00
2d 3h 18m 18s
0 bids
$41.82 Shipping
Condition: For parts or not working
Location: Burlington, United States
QU-BD Revolution RXL. It can print objects up to 228x216x228 mm in size. Retrofit Bowden Extruder for QU-BD Revolution 3D Printer - E3D extruder. Review:Machines ... moreon the Mind QU-BD Revolution XL Review Part 1-3.
$
14.99
Buy It Now
Free Shipping
Condition: New
Location: Andover, United States
This is Micro Swiss plated nozzle for LulzBot printers. It is made from a 360 brass base material and plated with TwinClad XT coating. TwinClad XT is ... morea nickel composite coating designed for very low friction.
$
37.99
Buy It Now
Free Shipping
Condition: New
Location: United States
Fits - Creality Ender 2/Ender 3/Ender 3Max/Ender 3 Pro/Ender 3 V2/Ender-5/Ender 5 6 7/CR-10 Series. High Speed Printing - Supports 250mm/s high speed ... moreprinting, compared with the normal hotend with a printing speed of 50mm/s, the printing speed can be significantly improved.
$
500.00
Buy It Now
Condition: Used
Location: West Covina, United States
For sale- a Stratasys Prodigy Plus ABS 3D Printer- Make Offer! We purchased this unit at the beginning of the year and used it for several projects. Recently ... morewe have had one issue with it and just do not have the time. Knowledge or drive to fix it. We are also downsizing and no longer have a use for it, so it needs to go. Everything on this unit works with only one exception: it has an issue with the support side clogging. Because of the problem we can no longer get it to print. Hopefully someone with more knowledge/experience can figure this out and will have a working printer. X. Y and Z work perfectly as do all heaters and feed systems. Unit boots, homes and heats up with no errors. Just has the clogging support issue. Keep in mind this unit was $70.000+ new. It is capable of a.007” layer height(same as the Dimension Elite) more precise then a 768sst or 1200sst. This is a commercial soluble support printer. Please excuse the lack of pictures, the unit is in a tight space in my office. Listing includes: Prodigy Plus printer(Serial#0021) 1 ABS Cartridge with about 87% left, 2 Support Cartridges(1 almost new, the other unknown) 12+ double-sided foam bases(most are new) Insight and Catalyst Software, all manuals(either in book or pdf form, some both) roller cart, etc. I can assist with freight shipping as this unit weighs about 300 pounds. I will strap and wrap onto a pallet for free. Here are some additional specs: Mechanical Dimensions: 864 x 686 x 1041 mm(34 x 27 x 41 in) Weight: 128 kg(282 lbs) Material: ABS Printing Build Size: 203 x 203 x 305 mm(8 x 8 x 12 in) Layer thickness: 013 or.010 or.007" Any questions just ask. Unit is being Sold As-Is* Check my feedback and buy with confidence. Payment required within 5 days. Paypal preferred. MO and cashier's check also accepted. Personal checks accepted but will have to clear first. Powered by The free listing tool. List your items fast and easy and manage your active items.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
3.49
Buy It Now
Condition: New
Location: Minneapolis, United States
(1) Red 6m. (1)Blue 6m. (1)Green 6m.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
1.88
Buy It Now
Free Shipping
Condition: New
Location: China
$
100.00
Buy It Now
$5.95 Shipping
Condition: New
Location: Fredericksburg, United States
It also fits the new Axiom printers. We use these in our own printers and they work very well on all of the materials we have tested. This alloy rivals ... moremild steel in strength.
$
2143.22
Buy It Now
Free Shipping
Condition: New
Location: Minooka, United States
3D Printer,120V,PC,Mac. Governing Law; Limitations. Diversion contrary to U.S. law is prohibited. Country of Importation and Anti-diversion. administered ... moreby BIS, and the International Traffic in Arms Regulations administered by DDTC.
$
21.84
Buy It Now
Free Shipping
Condition: New
Location: United States
Reel is suitable for most trendy printers, Comgrow, Geeetech, Longer, LABISTS, ANYCUBIC.etc. Spool size: Φ200mm/7.9" flange, Φ56mm/2.2" hub hole, 64mm/2.5" ... morewidth. Color: PLA black. without any exaggeration.
$
9.00
Buy It Now
$5.45 Shipping
Condition: New
Location: Magnolia, United States
Made for use with a Nema 17 motor.
$
12500.00
Buy It Now
Condition: Used
Location: South Lake Tahoe, United States
Price lowered $8.000 Here it is Folks. The real deal! Stratasys' production-grade FDM machine. This machine was commissioned in June'12 and has ... more1500 hrs logged on it. This machine comes with everything you need to get started. Here is a breakdown: 2) cartridges of soluble support(2) cartridges Black ABS plus(3) cartridges of Ivory ABS plus Tips. Wipers, loupe, wire brush, modelling bases, etc. I will purchase a new set of extrusion nozzles for the new owner. The material alone will cost you over $1700! The clean station is over $1200! All CD's and manuals. Clean station and chem's, and cables. You will need to network when plugged in. The software is MUCH more capable than the software on the"consumer-grade" machines. This is a professional machine that will cost you more than 50K to play! No stand with this machine. I couldn't justify the expense. It would, however, be cool to make a stand out of 80/20 extruded. I will have this machine and clean station crated at no expense. Shipping is up to the buyer. F.O.B Oshkosh. WI 54904(33x29x45: 450 lbs. Clean station is 2ft. cubed. approx. 80-90 lbs. These are approximates, actual shipping could vary.
$
15.00
Buy It Now
$5.95 Shipping
Condition: New
Location: Fredericksburg, United States
It also fits the new Axiom printers. We use these in our own printers and they work very well on all of the materials we have tested. These nozzles are ... moremade from 6061 Aluminum. It is used for High definition printing.
$
398.00
Buy It Now
Condition: Used
Location: Irvine, United States
Add your own mother boards and you’re ready to roll. Just think of the projects these will be great for.
$
1.47
Buy It Now
Free Shipping
Condition: New
Location: China
$
21.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
24.99
Buy It Now
$12.99 Shipping
Condition: New
Location: McDonough, United States
This low color resin grade demonstrates the best performance in formulated systems designed to enhance toughness or heat-resistance.
$
30.00
Buy It Now
$5.95 Shipping
Condition: New
Location: Fredericksburg, United States
It also fits the new Axiom printers. We use these in our own printers and they work very well on all of the materials we have tested.
$
79.99
Buy It Now
$14.99 Shipping
Condition: New
Location: Beaverton, United States
Formlabs ceramic resin V1 3D printer cartridge new sealed, this product has 04/14/20 date on but i am sure that it is the manufactured date, it is not ... moreold or dry, the auction is for one piece only but i do have 4 more as seen on the photos if interested, one of them does not come in the box. thank you for looking.
$
21.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
1200.00
Buy It Now
Condition: Used
Location: Grosse Pointe, United States
Powers on and works good. Made in USA. filters are included but are used and may or may not need to be changed.
$
27.19
Buy It Now
Free Shipping
Condition: New
Location: Independence, United States
These nozzles are 4mm inlet x. 4mm outlet and are typical of the updated style Flashforge Creator and others. IMPORTANT: If you have the Flashforge Creator ... moreor Creator Pro, check the pictures to see if you have the "ORIGINAL" version or the "UPDATED" version.
$
25.99
Buy It Now
$12.99 Shipping
Condition: New
Location: McDonough, United States
$
1800.00
Buy It Now
$206.79 Shipping
Condition: New
Location: Palm Beach Gardens, United States
We were a Z Corporation 3D Printer Dealer since 2001. This is a great machine for either Educational, Hobbyist or Professional applications. The CubePro ... moreprinters are solid, well engineered systems.
$
25.48
Buy It Now
Free Shipping
Condition: New – Open box
Location: Perris, United States
$
1940.38
Buy It Now
Free Shipping
Condition: New
Location: United States
& Recepticles. Electrical Outlets. Light Industrial. and Enclosures. Electrical Boxes. General Purpose. & Industrial. Industrial Scientific 17124504 Water/Dust ... moreSensor Filter,Pk5.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
400.00
Buy It Now
$206.79 Shipping
Condition: Seller refurbished
Location: Palm Beach Gardens, United States
We were a Z Corporation 3D Printer Dealer since 2001. This was a little used system we got on a trade-in. It was well taken care of, but still re-furbished ... moreand tested at our office. This is a great machine for either Educational, Hobbyist or Professional applications.
$
60.00
Buy It Now
$5.95 Shipping
Condition: New
Location: Fredericksburg, United States
It also fits the new Axiom printers. We use these in our own printers and they work very well on all of the materials we have tested. These nozzles are ... moremade from 6061 Aluminum. It is used for High definition printing.
$
21.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
9.79
Buy It Now
Free Shipping
Condition: New
Location: China
Feature: 1. Lightweight deburring tool with one-handed operation allows operators to reduce fatigue, easy to use. Deburring tool is made of plastic + ... morealloy materials in high quality, which makes itself getting great popularity.
$
0.99
Buy It Now
$3.00 Shipping
Condition: New
Location: China
CNC 3D Printer Mech Endstop Switch For RepRap Makerbot Prusa Mendel RAMPS1.4 Product information Description: CNC 3D Printer Mech Endstop Switch For RepRap ... moreMakerbot Prusa Mendel RAMPS1.4 Package Include: 1PCS*CNC 3D Printer Mech Endstop Switch For RepRap Makerbot Prusa Mendel RAMPS1.4 3PCS*Free cables Payment. Payment. Payable To. Note. PayPal All payments are due within 7 days of the close of auction. Failing to do so. Non-paying bidders will be reported to eBay. Shipping Policy. Delivery Time. We ship to worldwide. It usually takes 10-30 Business Days to delivery. Shipping address. We ship to your PayPal address. Please. Make sure to provide us with correct, precise, and detailed shipping Address. Send Time. Items will be shipped within 1 to 3 business days upon payment received or cleared. Note. If you don't receive items over 30 business days. Please notify us via eBay message. Return Policy. We appreciate your business and offer an instant 7 days return policy.7 days after receive the item) The returned item has to be in its original condition. We are able to refund your money without shipping cost. Contact us. For anything about product. Price, shipping or order status, please contact us via eBay message. We love positive feedback and 5 scores DSR. We will leave it for everyone that leaves it for us.
$
16.99
Buy It Now
$0.49 Shipping
Condition: New
Location: China
Suitable for heating circuit board of reprap machine. Material:Toughened glass. When heated, the adhesive force is good, and. 1x Glass plate. there is ... moreno special plastic film with cohesive weakening problems.
$
68.89
Buy It Now
Free Shipping
Condition: Used
Location: Cleveland, United States
Functional Condition Removed from the functional item!
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
14.79
Buy It Now
Free Shipping
Condition: New
Location: Independence, United States
MK8 HIGH PERFORMANCE/LOW-FRICTION EXTRUDER NOZZLE.4mm MK8 nozzle style. Specially Engineered for Improved Lubricity and Low Friction. Eliminate plastic ... moreglobs stuck to nozzle. Also check out our Ultra-FLAT Glass Build Plate System ,Aluminum Arm Stiffeners, Rep 2 Thermocouples, and our Overhead Spool Holder.
$
21450.00
Buy It Now
Condition: Used
Location: Holly, United States
Related Ideal Reference Numbers: 119552. This piece is located at Ideal Machinery, Inc. on our showroom floor. FREIGHT POLICY. It does not include manuals ... moreor printed materials. Removing or tampering with our security seals will automatically void the warranty.
$
4.24
Buy It Now
$2.99 Shipping
Condition: New
Location: United States
You can follow below process to chontact us. Product Feature. Color: Black. Import Duties. Product Instructions.
$
7.05
Buy It Now
Free Shipping
Condition: New
Location: United States
Super elastic. Material: stainless steel.
$
14.75
Buy It Now
Free Shipping
Condition: New
Location: China
Feature: 1. Check the model! Wide Compatibility: This heater can also be used for other 3D printers. However, if the connector is not suitable for your ... moreprinter, replace the connector. Heating Range: Less than 350℃.
$
5.62
Buy It Now
Free Shipping
Condition: New
Location: China
It is made from PLA material which has low shrinkage rate and do perform well in testing. The standard size and and common working temperature make it ... morea necessary gadget for 3D lover. It is spooled well without contamination.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
24.89
Buy It Now
Free Shipping
Condition: New
Location: Independence, United States
These nozzles are 3mm inlet x. 4mm outlet and are typical of the Flashforge Creator, Wanhao Duplicator, and others. IMPORTANT: If you have the Flashforge ... moreCreator or Creator Pro, check the pictures to see if you have the "ORIGINAL" version or the "UPDATED" version.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
24.99
Buy It Now
Free Shipping
Condition: New
Location: Los Angeles, United States
3D Printer Parts. PLA, or Polylactic Acid, is a commonly used thermoplastic material that does not require the use of a heated print bed. Compatible with ... moremost 3D printers currently out on the market.
$
7.23
Buy It Now
$3.39 Shipping
Condition: New
Location: China
1 set of 3d printer extruder(As the picture shows). Thermistor : 100K NTC B 3950 ±1%. We will try our best to save your problem ASAP. Type: Short-Distance.
$
8999.98
Buy It Now
$299.99 Shipping
Condition: Used
Location: Orlando, United States
Available now is this Envisiontec Perfactory 3 Standard SXGA+ high resolution DLP 3d printer.
$
1100.00
Buy It Now
Condition: For parts or not working
Location: Easton, United States
The printer does not work (It powers up to illuminate the front screen displays, but no characters are generated on the display, unit does not logically ... morepower up). Item has several motherboard light indicators indicating either a green or red condition, but otherwise, unit does not logically power up.
$
12.38
Buy It Now
Free Shipping
Condition: New
Location: United States
20 Pieces Yellow Heating Bed Spring Die Head Spring 3D Printer Compression Spring 0.31 in OD 0.78 in Length, Compatible with Creality CR-10 10S S4 Ender ... more3 Heating Bed Spring Bottom Connection Level. 20 Pieces yellow heating bed spring die head spring 3D printer compression spring 0.31 in OD 0.78 in length, compatible with Creality CR-10 10S S4 Ender 3 heating bed spring bottom connection level Compatible with: These yellow bed springs are compatible with most 3D printer heating beds, Ender 3, Ender 3 pro hot bed springs, flat top and hard springs.
$
9.05
Buy It Now
Free Shipping
Condition: New
Location: China
The hardened wear-resistant nozzle can prolong the service life. It can print PEEK PEI carbon fiber glass fiber material with excellent effect. Compared ... morewith the old model, this model adopts small pointed nozzle type silk printing to print more effectively and quickly.
$
14.00
Buy It Now
$5.99 Shipping
Condition: New
Location: Tulsa, United States
Heater Block Cotton(300C). This product is Designed for 3D printers, don't use it outdoor and shut off power before starting installation work. Important ... moreSafety Guide.
$
35.99
Buy It Now
Free Shipping
Condition: New
Location: Denver, United States
CREALITY CR10 EXTRUDER CAN WORK WITH DIFFERENT SIZE MK8 NOZZLE: 0.2MM 0.3MM 0.4MM 0.5MM 0.6MM 0.8MM 1.0MM NOZZLE. MK8 CR10 EXTRUDER HOT END KITS,WHITE ... moreWIRE WAS TEMPERATURE THERMISTOR, BLACK WIRE WAS HEATING TUBE 12V 40W.
$
50.00
Buy It Now
Free Shipping
Condition: New
Location: Magnolia, United States
Made for use with a Nema 17 motor.
$
10.99
Buy It Now
Free Shipping
Condition: New
Location: China
Product material: brass. Product caliber: 0.4mm. We aim to make our service as reasonably priced as possible. We will do our best for you!
1 2 3 4 5 6 7 8 9 10
 In 

Former Listings  
 
Printrbot LC, Reprap 3D printers, Assembled, MDF with upgrades, Heated Bed
Printrbot LC. Reprap 3D printers, Assembled, MDF with upgrades, Heated Bed This one of our testin units Printrbot LC Modified. It has all what original Printrbot LC. Modifications Included: Z-Axis 5/16" rods was replaced with 5mm* Used standard J-Head 0.5 mm for 3mm filament nozzle. Extruder mounting was modified to accept any extruders. Added LED Stripe under X-Axis(looks great in dark room) Electronics(Sanguinololu 1.3A) with case was mounted on a right site for easy access. Firmware Sprinter(can email all settings including firmware) Will include all what you see on first picture. Software can be downloaded from Repetier host website. Printer was tested with PLA and ABS- no problem found. Good luck and happy 3D printing! On May-31-13 at 09:27:50 PDT. Seller added the following information:
Set of 4 NEMA 17 stepper motors for CNC, 3D Printers. Mendel, RepRap.
Type 17PM-J034-P2VSMinebea Co. LTD. You get 4 motors Better performance! a removable damper. It is ideal for applications where motor noise and vibration need to be minimized, such as in security camera controls, simple movement systems in analytical instruments or in marking engraving machines, repraps, markerbots etc. DC 24 volts 1.2 amps. I run them at 12 volts.8 to 1 amp. I always start at the lowest settings and work my way up to find the best run. You should be able to go up to 1.2 amps. NEMA 171.8 deg/ step4 wire connectionwidth 42mm x 42mmtotal length of 34 mm5mm diameter shaftsshafts length 20 mmWeight 10 oz.Type of Laminated Stator(2 Phase Hybrid(Better Performance at high speed) Pulley 9.3mm x 10.4mm dia. Pitch on teeth is 2, 17 teeth, can be remover with a nut splitter, a small gear puller. PIN1= B-PIN2= B COMMONPIN3= BPIN4= APIN5= ... moreA COMMONPIN6= A- They’re in very good cosmetic condition. And were removed from working equipment.
Brass Pepsi Cola Printers Block Template Stencil 3D Embossed Sign Banner Chicago
Offering a vintage Pepsi Stencil. It is made of brass. Marked by maker Banner Chicago. It is about 5 1/4" long by 3" tall. I understand they are used to mark crates. Carriers, racks and boxes. In great condition. I have about 7 different ones so take a look. I bought quite of bit of other items on this trip so sit a spell and look at my other auctions. The legal stuff: I buy merchandise from estate sales, flea markets, auctions, and good old picking. So please look at photos and ask questions before you bid I want us both happy. I strive for 5 star performance. Payment due within 5 days. Unpaid case opened after 7 days. Good Luck.
Brass Pepsi Cola Bottlers Printers Block Template Stencil 3D Embossed Soda Sign
Offering a vintage Pepsi Bottler Stencil. It is made of brass. It is about 10 1/2" long by 2 1/2" tall. I understand they are used to mark crates. Carriers, racks and boxes. In great condition. I have about 7 different ones so take a look. I bought quite of bit of other items on this trip so sit a spell and look at my other auctions. The legal stuff: I buy merchandise from estate sales, flea markets, auctions, and good old picking. So please look at photos and ask questions before you bid I want us both happy. I strive for 5 star performance. Payment due within 5 days. Unpaid case opened after 7 days. Good Luck. g.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bjw%60hquvg%3Eg-13f217eb64c-0xf6-
GE Voluson i Portable 3D/4D ultrasound Machine with 4 probes & 2 printers
GE VOLUSON I 3D/4D MACHINE WITH 3 1/2 MONTHS OF WARRANTY LEFT. USED LESS THAN 10 TIMES. MACHINE COMES WITH 4 PROBES. THREE OF THE FOUR PROBES ARE NEW FROM GE AND HAVE NEVER BEEN USED AFTER RECEIVED. AND ALL COME IN THEIR ORIGINAL BOXES, REFURBISHED PROBE(1) HAS CERTIFICATE OF COMPLIANCE DIRECTLY FROM GE. TRANSVAGINAL PROBE IS NEW AND BOX IS SEALED. INCLUDES CARRYING CASE, EXTERNAL DVD WRITER, 11 ROLLS OF HIGH GLOSS PRINTER BW PAPER, 1 DISINFECTANT TUB, AND 10 BOTTLES OF GEL. POWER SUPPLY AS WELL. MACHINE IS READY TO GO. GREAT FOR A 3D/4D ELECTIVE OR DIAGNOSTIC ULTRASOUND BUSINESS.
NIGERIA 1965/1966 -1D 2D 3D 4D 6D 9D 1/-- USED NO PRINTERS NAME WITH DESIG
NIGERIA 1965/1966- 1D 2D 3D 4D 6D 9D 1/ WITHOUT PRINTERS IMPRINT WITH DESIGNERS NAME- USED Check out my! POSTAGE& PACKING ON MULTIPLE PURCHASES 0.20 PENCE EACH ADDITIONAL LISTING International buyers welcome. Please payment by Paypal only. THANKS FOR LOOKING
Extrusionbot - 3mm Filament Extruder for 3D printers
I have for sale a used Extrusionbot filament extruder for 3D printers. The nozzle I will ship with allows for extrusion of 3mm diameter filament. Other filament diameters would require a different nozzle that you can purchase online. You can find the complete details of the product on the Extrusionbot website. The Extrusionbot is as fast as advertised but I have not used it as much as expected. So my loss is your gain. I am also including 3 lbs of ABS pellets for extruding along with a spool for winding the filament. Please let me know if you have any questions and don't miss your chance to get a lightly used extruder for much less than new. I am only shipping domestically so sorry for any inconvenience. Thanks for looking!
Lot of 5 stepper motors robot, CNC mill router, Makerbot, Reprap, 3D printers...
5 stepper motors made by Nidec Servo Corporation. In excellent working condition. Model KH39FM2-851 Bipolar steppers. 1.8 degrees per step. High Torque(1.3 times as high as conventional products) and low noise(7dB quieter than conventional products) Holding Torque 118mNm(17 oz-in) Operates with a 24V stepper driver. 37mm x 37mm. 27mm long. Shaft diameter 5mm, 16.5mm long Specifications and dimensions are shown in attached photos. Perfect for applications requiring precision motion control such as CNC mills or routers. Computer controlled manufacturing equipment, 3D printers, robotics, and test and measurement systems. Motors currently have pinion gears or timing belt pulleys on them. But these can be removed prior to shipment if the buyer requests. Connection wires will be provided.
NIGERIA 1969/72 -- 3D 6D - USED WITH PRINTERS NAME & WITH DESIGNER NAME
NIGERIA 1969/72- 3D 6D-USED- WITH PRINTERS IMPRINT& WITH DESIGNERS NAME- Check out my! POSTAGE& PACKING ON MULTIPLE PURCHASES 0.20 PENCE EACH ADDITIONAL LISTING International buyers welcome. Please payment by Paypal only. THANKS FOR LOOKING
AUSTRALIA SG148 3d GUTTER BLOCK OF 3 MARGINAL JOHN ASH PRINTERS INSCRIPTION
WELCOME TO TAYLOR'S COLLECTABLES BACK AFTER THREE YEARS REST- PLEASE NOTE ALL OF THESE BLOCKS COULD BE SENT FOR THE SAME COST AS ONE AUSTRALIA SG 148 GUTTER BLOCK OF THREE WITH INSCRIPTION UNMOUNTED MINT THE BLOCK HAS A LIGHT GUM CREASE ALONG THE CENTRE OF THE GUTTER SEE SCANS- MY STARTING PRICE IS ONLY £10.00 WITH NO FURTHER RESERVE 100% SATISFACTION GUARANTEE.IF YOU ARE UNHAPPY FOR ANY REASON JUST RETURN YOUR ITEM IN THE CONDITION RECEIVED WITHIN 14 DAYS OF RECEIPT FOR A COMPLETE REFUND INCLUDING POSTAGE BOTH WAYS.ITEMS ARE CAREFULLY PACKED AND POSTED PROMPTLY.POSTAL SAVINGS FOR MULTI-PURCHASES. POSTAGE AND PACKING COSTS SEE SEPARATE SECTION MAXIMUM SENDING IN ONE PARCEL IS 2 KILOS. Check out my other items! Be sure to add me to your favourites list! HAPPY AND SUCCESSFUL BIDDING.
3D Printers (2) ZCorp Spectrum z510
Normal 0 false false false EN-US JA X-NONE Rapid 3D printing means no more waiting for high-definition prototypes. The Spectrum Z510 3D Printer produces high-definition. Full-color prototypes quickly and affordably. Its remarkable inkjet technology creates parts with detailed features, precise accuracy, and 24-bit color, so you can print and evaluate physical models of your design concepts in a matter of hours in their nearly finished state. The Z510's unique color capability builds superior color models that effectively communicate your design ideas. While giving you a definite strategic advantage during product development. ● Build Speed: 2 layers per minute ● Build Size: 10" x 14" x 8" 254 x 356 x 203 mm) ● Layer Thickness: User selectable at the time of printing; 0.0035"0.008" 089-203 mm) ● Material Options: ... moreHigh performance composite. Elastomeric, direct casting ● Resolution: 600 x 540 dpi ● Number of Print Heads: 4 ● Equipment Dimensions: 42" x 31" x 50"107 x 79 x 127 cm) Equipment Weight: 450 lbs. 204 kg) Normal 0 false false false EN-US JA X-NONE Depowdering Stations(3) All three depowdering stations have working vacuum systems. But only one of the three has pressurized air working. Both others appear to have leaks that could be fixed. ZD-4(beige metal- also has a light. Vacuum power knob, and external switch) two ZD-5(gray plastic) ZW-4 Paraffin wax dip(1) Excellent condition. The simplest and most cost effective post-processing method. This paraffin wax dipper submerges the print in hot paraffin wax which bonds the plastic and brings out the color of the model. The machine is about ⅔ full of wax. xlaform- high strength thermoresin dip(1) The LCD on the computer is broken and requires either a new screen or a new computer. Sent to representative at xlaform. Roughly 1L of the thermoresin has been removed from the machine. The remaining resin in the machine has congealed and will need to be removed with acetone and elbow grease. Supplies Fluid We have ~1L of old
3D Printers ZCorp Spectrum z510 (total of 2)
Rapid 3D printing means no more waiting for high-definition prototypes. The Spectrum Z510 3D Printer produces high-definition. Full-color prototypes quickly and affordably. Its remarkable inkjet technology creates parts with detailed features, precise accuracy, and 24-bit color, so you can print and evaluate physical models of your design concepts in a matter of hours in their nearly finished state. The Z510's unique color capability builds superior color models that effectively communicate your design ideas. While giving you a definite strategic advantage during product development. Will sell separate email for price. ● Build Speed: 2 layers per minute ● Build Size: 10" x 14" x 8" 254 x 356 x 203 mm) ● Layer Thickness: User selectable at the time of printing; 0.0035"0.008" 089-203 mm) ● Material Options: High ... moreperformance composite. Elastomeric, direct casting ● Resolution: 600 x 540 dpi ● Number of Print Heads: 4 ● Equipment Dimensions: 42" x 31" x 50"107 x 79 x 127 cm) Equipment Weight: 450 lbs. 204 kg) Depowdering Stations(total of 3) All three depowdering stations have working vacuum systems. But only one of the three has pressurized air working. Both others appear to have leaks that could be fixed. ZD-4(beige metal- also has a light. Vacuum power knob, and external switch) two ZD-5(gray plastic) ZW-4 Paraffin wax dip(total of 1) Excellent condition. The simplest and most cost effective post-processing method. This paraffin wax dipper submerges the print in hot paraffin wax which bonds the plastic and brings out the color of the model. The machine is about ⅔ full of wax. Xlaform- high strength thermoresin dip(total of 1) The LCD on the computer is broken and requires either a new screen or a new computer. Sent to representative at xlaform. Roughly 1L of the thermoresin has been removed from the machine. The remaining resin in the machine has congealed and will need to be removed with acetone and elbow grease. Supplies Fluid We have ~1L of old fluid. Powder We have 6
10 lb of gears a Mix of of Materials for 3D printers or Robots or DIY projects
This auction is for over 10 lbs of gears There is a mix of Steel. Brass,aluminum, and plastic. Some big and some small. Please see the pictures. I have had these for awhile. But need to make room for new projects(see) dhep.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bishm%3Ed%7Fhep-14abbb3c3fb-0x102-
Afinia H480 3D Printer EE494180 Computer Printers
Title: Afinia H480 3D Printer Photo: Stock Photo. Please see item notes for details. Format: Computer Printers ISBN/ UPC: 678621110028 Internal Product Sku: EE494180 Item Type: Computer Printers Location: XX25 Condition: Used: Acceptable Details about the item: Acceptable Condition AFINIA H480 3D Printer. Includes USB cable and power cable. Includes Nozzle Wrench. Wire Cutters, Putty Knife, Xacto Knife, Allen Wrenches, USB B Cable, Power Cable and Gloves. Our small business sells new and used items. We take great pride in our service and strive to make every shopping experience great. If you have any issues please contact us first. Product Information: Please do not assume an item has something included if it is not mentioned in the notes section. Most photos are stock photos and do not depict the actual item. So please take a moment to read ... morethe description that is in yellow. We will be happy to respond quickly via email to any questions you have about an item, so feel free to drop us a line. We classify items in these categories: Brand New items are unused and factory new. Refurbished items processed to ensure they meet original manufacturer specifications. Like New items have very minor wear. If any. Very Good items are well cared for but will have light wear and tear from normal use. Good items show wear from use. But remain fully functional. They maybe marked, or have identifying markings on it, or show other signs of previous use. Acceptable items are fairly worn but continue to work with fully. Signs of wear can include aesthetic issues such as scratches. And discoloration. Used Media items will not have DLC Add-On codes. We also do not sell any PAL items. Meaning our items will only work in NTSC video equipment. Payments: We accept PayPal for all payments. We are required by law to collect Ohio sales tax. Store Hours And Support: We are open Monday through Friday. 8:30AM-5:30PM EST. We are closed Saturday, Sunday, and all major holidays. If you contact us after store hours, we'll reply on the next busi
XYZ pro Resetter for davinci 3d printers, xyzprov1 from wctek
Made by wctek. If you have a xyz davinci 3D printer. This is for YOU. This will enable you to use any brand filament you like. And change bed and extruder temps. Check wctek website for more details. This version of the XYZPROv1! comes fully assembled and tested. This interface is designed for the one of you that wants maximum flexibility out of the XYZ Printer. It allows you to set the extruder and bed temps to just about any value(as long as it's supported by the current firmware) this goes for the filament length as well. Ever wanted to run PLA on your XYZ? Well. With this you can(make sure your PLA filament is the correct diameter as the XYZ's extruder is very picky when it comes to filament diameters) To communicate with the XYZPRO you need a simple serial terminal program(see wctek for information on how to use and install the ... moreArduino IDE which has a free Serial terminal built-in) NOTE: USE THE ARDUINO IDE VERSION 1.0.5-RC2 WHICH ALSO SUPPORTS WINDOWS8 XYZPRO allows you to import and export EEproms images and paste them as simple text in forums to share with your friends. Build your special settings for each type of imaginable filament and save the eeprom images in a text file for easy recall. What if your cartridge truly dies and/or the EEprom gets corrupted? Not a problem! Hit option 9 and restore the cartridge to a factory EEprom image(stored in the XYZPRO's memory) Package includes: 1 x XYZPRO(usb) 1 x USB Cable, Used but looks and works great! I no longer need it.
ONLINE COMPUTER STORE 4SALE - TABLETS, DESKTOPS, LAPTOPS, 3D PRINTERS & MORE! a
THE ULTIMATE COMPUTER AND ACCESSORIES STORE- AFFILIATE ONLINE BUSINESS WEBSITE FOR SALE! Click Here To View Our Demo Site. This offering is for a huge. Fully Stocked Computer And Accessories Business. The Entire Website Itself Is Loaded With Hundreds Of Thousands Of Products& Pays You Commissions of 4%75% of the actual sale price for each and every sale. Your visitors simply visit your website. And add the items they wish to buy to their shopping cart. The order is then automatically received, processed& shipped on your behalf by The World's#1 Online Retailer or other vendor. There Is No Inventory To Buy- No Orders To Place- And No Products To Ship- That's All Done For You Automatically! Bidding on the HTML code starts at just.01 Cent- This is for those who know how to read HTML and setup a custom affiliate website for themselves ... moreusing our layout. If you set it up yourself the entire process may take you anywhere from a few hours to a few days depending on how familiar you are with HTML and the complete setup process. If you're not exactly sure how to apply the HTML code or the affiliate setup process. I do hope you'll allow us to set it all up for you with our Optional Setup Package. OPTIONAL SETUP IS JUST $129& Includes Complete Setup. A Domain Name& Free Hosting For The Next 5 Years! END RESULT: A Fully Stocked. Automated Online Business That Pays You Commissions For Each& Every Sale. Since most people do purchase our optional setup. We'll go ahead and include the setup on your ebay invoice. We'll then have your site 100% ready to start making you money the instant you receive it. Usually within 4/5 days. If you choose not to have us setup your website. Please just let us know and we'll send you another invoice. It's our job to listen& our only mission is a happy. Satisfied customer! Start A New Business Or Expand Your Existing Business Today! If you're an eBay seller, we'll even link your eBay items directly to your new site. This is all included
Used Build Platform for FormLab Form1/Form1+ SLA 3D Printers
Used Build Platform for FormLab Form1/Form1+ SLA 3D Printers These build platforms were slightly used. They are working for both Form1 and Form1+.
Mobile Double Scissor Lift 770 lb. Cap.w/Custom Table Top for Zcorp 3D Printers
Mobile Double Scissors Lift Table 770 lb. Capacity- Used 1 year old. In working order ● This lift was recently acquired from a 3D printing shop. It was used to gently transport 3D images to and from Zcorp printers. It has a custom made table top that can easily removed so that the stock top can be used. See pictures for condition. ● Perfect for use with Zcorp 3D printers and Zcorp Powder Recyclers Capacity: 770 lbs. Table size: 35-1/2" x 19-1/2" stock) Raised height: 51" Lowered height 14" Overall dimensions:19-1/2" W x 45-1/2" D x 37"H Fixed handleChrome plated handle and foot pedal Lever release handle Polyurethane locking swivel casters Foot operated pump
Zcorp - ZD5 Powder Recycling Station for 3D Printers
Zcorp Zd5 ● 1 year old ● last use 12/10/14 ● See pictures for condition ● only come with what is in pictures ● Contact seller for freight quote
Lot - (3) 3D Nail InkJet Printers and (1) Mulit-function InkJet Printer
This Aucion is for 4 Units- 3 nail printer(2 with fingernail/ toenail combo units) and 1 Multi-function 3D inkjet printer Regarding nail printers- Print Nails And Toenails Synchronously with combo unit! Can You Imagine If Clients Would Like To Print Her Fingernails With The Same Printer Which Has Printed Others Toenails? One Built-in PC Controls Two Printers. Upper One Is For Fingernails, Lower One Is For Toenails. Clean, Efficient And Practical! It Can Print Any Images On Natural Nails Or Artificial Nails 8.5 Inch LCD Liquid Crystal TOUCH SCREEN With Professional Touch Pen 3.000,000 High Resolution Camera For Snapshot Built-in PC Electric Power Is Reduced. Working Hundreds Hours Only Costs TWO Degrees! Comfortable Curved Mold Finger Nail Holder Exactly Printing Record For Control Renting Business Images Are Fast Dry And Water Proof Pre-stored ... moreMillion Images. Your Own Pictures Can Be Saved Through U-Disk Powerful Words/Images Editing Function Suitable For Salons. Malls, Supermarkets And Nail Art Room. Specification: Machine Dimension?475(L)X365(W)X915(H)mm Input voltage: 220V 50Hz or 110V 60Hz Net weight: 37kg. Regarding Multi-Function 3D Inkjet Printer- Candle printer can print any picture and words on Candles. Golf, Crystal, Fruit, chinaware, coffee mug, Card, flask and tiles etc. It is very sharp and easy to use. You won't need any professional skills. Specification: 1- Four ways for you choose pictures which are print on Candles and others A. Default Gallery. We will give you gallery where there are patterns for you. B. Customs Choose Patterns. You can print any patterns from your computer C. Present Prompt Photo-taking. You can print your photos on the nails. Flowers and others D. Strong Present Write and Edit. You can print the word you write and edit on the object at present. 2- Electronic Automatic flat holder Adjust System 3- It is made of metal mould. 4- The patterns it print are fast drying and waterproof 5- Size: 460mmx295mmx250mm 6- Input voltage: 220V 50Hz or 110V 60Hz 7- Volume Weigh
ONLINE COMPUTER STORE 4SALE - TABLETS, LAPTOPS, 3D PRINTERS, INK, DESKTOPS + a
COMPUTER AND ACCESSORIES STORE- AFFILIATE ONLINE BUSINESS WEBSITE FOR SALE! Click Here To View Our Demo Site. This offering is for a huge. Fully Stocked Computer And Accessories Business. The Entire Website Itself Is Loaded With Hundreds Of Thousands Of Products& Pays You Commissions of 4%75% of the actual sale price for each and every sale. Your visitors simply visit your website. And add the items they wish to buy to their shopping cart. The order is then automatically received, processed& shipped on your behalf by The World's#1 Online Retailer or other vendor. There Is No Inventory To Buy- No Orders To Place- And No Products To Ship- That's All Done For You Automatically! Bidding on the HTML code starts at just.01 Cent- This is for those who know how to read HTML and setup a custom affiliate website for themselves using ... moreour layout. If you set it up yourself the entire process may take you anywhere from a few hours to a few days depending on how familiar you are with HTML and the complete setup process. If you're not exactly sure how to apply the HTML code or the affiliate setup process. I do hope you'll allow us to set it all up for you with our Optional Setup Package. OPTIONAL SETUP IS JUST $129& Includes Complete Setup. A Domain Name& Free Hosting For The Next 5 Years! END RESULT: A Fully Stocked. Automated Online Business That Pays You Commissions For Each& Every Sale. Since most people do purchase our optional setup. We'll go ahead and include the setup on your ebay invoice. We'll then have your site 100% ready to start making you money the instant you receive it. Usually within 4/5 days. If you choose not to have us setup your website. Please just let us know and we'll send you another invoice. It's our job to listen& our only mission is a happy. Satisfied customer! Start A New Business Or Expand Your Existing Business Today! If you're an eBay seller, we'll even link your eBay items directly to your new site. This is all included with Our Opt
3D Systems - Instant-Load ABS Cartridge for Cube 3D Printers - White (Used)
Used ABS White Cartridge for Cube 3D printer Gen 3. The cartridge jet is jammed. But the material inside is still good at 92% left. It may still qualify for a new replacement under warranty if you contact 3D system.
2 Printrbot ABS Filament for 3D printers, 1.75mm Diameter, Black, 1Kg Spool
Lot of 2 Printrbot ABS Filament for 3D printers. 1.75mm Diameter, Black, 1Kg Spool: Specifications for this item: Brand Name Printrbot, Color Name Black, Material Type ABS(Acrylonitrile Butadiene Styrene) Number of Items 1, Outside Diameter 1.75 mm, Overall Height 3 inches, Overall Length 8.5 inches, Overall Width 8.5 inches, Part Number Printrbot-Black ABS Filament, UNSPSC Code 23260000 Product details: Spool of ABS plastic filament Diameter of 1.75 mm For use with 3D printers(sold separately) Print temperature range from 220 to 240 degrees C Black color Product Description: The Printrbot ABS filament is a 1 kg spool of black ABS(acrylonitrile butadiene styrene) plastic formed as a continuous. 1.75 mm diameter filament. The filament is used to fill the material reservoir of a 3D printer(sold separately) and has a print temperature range ... morefrom 220 to 240 degrees C. It is rolled on a spool for mounting onto a 3D printer's spool holder(sold separately) ABS plastic has good impact resistance, chemical resistance and heat stability. Retail open package items. If you have any questions regarding the item feel free to contact us. Thanks for looking! Posted with