|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Condition: Used Location: Israel RB 840-RB1300 Bag maker Hudson Sharp bag making line (2003), consisting of - Roll core size: 3" (76 mm). roll changes: 20-24. bag length: 17" (432 mm). ... morespeed: 650 feet/min (198 m/min) or 250 bag separations/min.
|
|
|
|
40555001 Used- Cast Film Line, 14" wide, consisting of: (1) Egan 2-1/2" single s
Used- Cast Film Line. 14" wide, consisting of: 1) Egan 2-1/2" single screw extruder, approximately 32 to 1 L/D ratio. 5 zone electrically heated, water cooled, non-vented barrel with closed loop system with tank, pump, and heat exchanger. Driven by a 60 hp, 500 volt, 1750/2100 rpm DC motor thru a gearbox, ratio 11.06 to 1. 1) Manual screen changer. 1) Control panel with West 2070 controllers, and a Reliance VS Maxpax III drive, extruder serial#901846-479939, built 1991. 1) A& A Associates quench tank, 304 stainless steel, 24" x 33" x 31" deep, 2) 4" diameter x 17" wide rubber pull rolls, driven by a 1 hp gearmotor. 1) A& A Associates cooling tank, 304 stainless steel, 24" wide x 96" long x 12" deep with(2) sets of pull rolls, 1) control panel with Digitrac panels. 1) Independent Machine ... moreCompany take up/slitter/winder, model 12SR, serial#6581-1290. 4) Slitter blades manually adjustable, 1) static eliminator, rubber/metal pull rolls, tension bar, two station winder, and a control panel. 3) Transformers, 15, 45, 75 kva. ref# 40555001 Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2Bf54%3E-13fac376b56-0xff-
|
|
|
45092001 Used- Berstorff Twin Screw Pelletizing Line Consisting Of: (1) Berstorf
Used- Berstorff Twin Screw Pelletizing Line Consisting Of: 1) Berstorff 25mm twin screw extruder. Model ZE25X330, serial#301-3792. Co-Rotating design, side by side screws. Approximate 33 to 1 L/D ratio. 6 barrel sections(3) top vented, 1 water cooled feed section with dosing feeder, and hopper. Electrically heated, air cooled. Approximate 43-1/2" centerline height. Driven by an approximate 7.5hp DC motor thru a reducer. 1) Sihi 3hp vacuum pump, 1) 2 Hole stand die, 1) operator control panel with Eurotherm 808 controllers, Fincor 3135 DC drive, and an Auto Mate 15 programmable controller. 1) Dual lip air knife with a 3hp blower, 1) Pelletizer, approximate 2” wide 8 blade rotor, with metal, and rubber pull rolls, driven by an approximate 3hp motor. ref# 45092001 Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. ... moreIl. 60106 Phone: 630-350-3021 Fax: 630-350-0780
|
|
|
44977001 Used- Wayne Machine Pelletizing Line consisting of: (1) Wayne Machine
Used- Wayne Machine Pelletizing Line consisting of: 1) Wayne Machine 1-1/2" single screw extruder. Approximately 24 to 1 L/D ratio. Electrically heated. Air cooled top vented barrel. Water cooled feed throat with hopper, approximately 40" centerline height. Driven by a 7.5 hp, 500 volt, 1750/2300 rpm DC motor thru a reducer, no ratio. Includes a control panel with Eurotherm 808 controllers, and a Melltrum drive, all mounted on a common base, serial#4839. 1) 4 Hole strand die. 1) Wayne stainless steel water bath. Approximately 48" long x 18" wide x 16" deep. Includes a 6" wide air knife, mounted on a carbon steel frame with casters. 1) Wayne pelletizer. 2" Wide(8) fixed blade rotor, 1) rubber, 1) metal pull roll, all driven by a 1-1/2 hp DC motor with a Dart speed controller. Mounted on casters. ref# 44977001 ... moreSteven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780
|
|
|
44941004 Used- Sterling Pelletizing Line consisting of: (1) Sterling 2.5" diame
Click To Enlarge- Used- Sterling Pelletizing Line consisting of: 1) Sterling 2.5" diameter single screw extruder. Approximately 30 to 1 L/D ratio. Electrically heated. Water cooled vented/plugged barrel with closed water loop system. Extruder is driven by a 50 hp DC motor with SCR control. Has free standing mounted temperature panel. 1) Beringer SL25 screen changer with pump. 1) Strand die, 1) 18" wide x 14" deep x 11'2" long stainless steel water bath with pump and heat exchanger. 1) Berlyn model HV1 air stripper, 6-5/8" slot opening, serial#071C617. 1) 4" Conair model 304 pelletizer, serial#6-041984, driven by 2 hp DC motor with controls. ref# 44941004. Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: ... moreUnited States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
81494 USED: Filmaster lab size blown film line consisting of (1) Filmaster 2" si
Click To Enlarge- USED: Filmaster lab size blown film line consisting of(1) Filmaster 2" single screw extruder. 24:1 L/D, electrically heated, air cooled 2 zone non-vented barrel. Water cooled feed with hopper. Driven by a 25 hp DC motor thru a reducer, ratio 10.286:1. 1) 2" manual screen changer, fixed die block, 3-1/2" blown film die, air ring with blower, 1) 24" wide x 36" tall collapsing frame with slats, 2) 5-1/2" diameter x 24" wide rubber nip rolls, driven by a 1 hp DC gearmotor, 1) Filmaster winder, 24" wide nip rolls, 24" wide winder and air knife. Includes a control panel with RKC C40 digital controllers, transformer, SSD DC drive panel. 5966 hours on meter. ref# 81494. Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact ... morethe seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex g.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bjw%60hquvg%3Eg-13faf55c8a3-0xfa-
|
|
|
80281 Used- Munchy Recycling Line Consisting Of: (1) Munchy single screw extrude
Click To Enlarge- Used- Munchy Recycling Line Consisting Of: 1) Munchy single screw extruder. Model P100, electrically heated, air cooled barrel, driven by a 69 kW DC motor thru a gearbox, with control panel, Eurotherm 94 digital controllers, Eurotherm 590 DC drive panel, manual screen changer, 180 hold strand die; 1) Munchy pelletizing system with 2 blade pelletizer, driven by a.75 kW motor, water slie, 3 kW spin dryer, holding tank with pump. ref# 80281. Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary ... moredepending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
79203 Used- Egan 40" Cast Film Line Consisting Of: (1) Egan 3.5" extruder, 20:1
Click To Enlarge- Used- Egan 40" Cast Film Line Consisting Of: 1) Egan 3.5" extruder. 20:1 L/D ratio, electrically heated, water cooled, 100 hp main drive motor with SCR controller, 16.94:1 gearbox ratio. 1) 11 zone digital temp control panel. 1) Foremost crammer feed unit. 1) 3.5" hydraulic slide plate screen changer. 1) Black Clawson 40" cast film die, size 300XL-40, serial#18111. 1) Egan two roll cast station having(1) 24" diameter x 40" face and(1) 16" x 40" face cooling rolls, air knife and idler rolls. 1) Egan single turret winder, 30" diameter finish having 6" cores. ref# 79203. Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All ... moreitems sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
44765001 Used- Dr. Collin Laboratory Pelletizing Line consisting of: (1) Collin
Used- Dr. Collin Laboratory Pelletizing Line consisting of: 1) Collin 25mm co-rotating twin screw extruder. Type Kneter 25 x 24 D, serial#525A-18-93, built 1993. Side by side screw design, approximately 24 to 1 L/D ratio. Electrically heated, air cooled, 3) barrel sections, 2) are vented, 1) water cooled feed section with hopper, approximately 39-1/2" centerline height. Driven by a 7.1 kw, 440 volt, 50/2500 rpm motor with gearbox. Includes(1) 3 mm(3) hole strand die, 1) operator control panel with Ero Electronic controllers, and a control panel. Frame mounted with casters. 1) Collin water bath, model 2000mm, stainless steel. 195 mm(7.6" Wide x 2000 mm(78.7" long x 114 mm(4.5" deep. Adjustable height from 800 mm to 1100 mm, water capacity approximately 32 liters. Includes a pump. Mounted on casters, serial#4330-12-99, built ... more1999. 1) Collin strand pelletizer, model CSG 171/2. 1) 30 mm(1.18" wide fixed blade rotor, maximum diameter of stand 5 mm, number of strands 1 to 3. 1) Metal, 1) rubber pull roll, driven by a 0.18 kw motor, pelletizer driven by a 1.5 kw, 360 volt, motor. Includes manual speed controls, and a control panel with a Nordac drive, base mounted on casters, serial#4130-12-99, built 1999. ref# 44765001 Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 260.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E260-13fb1c3eae2-0x106-
|
|
|
44517001 Used- Davis Standard 7” Wide Sheet Line consisting of: (1) Davis Standa
Used- Davis Standard 7” Wide Sheet Line consisting of: 1) Davis Standard 1-1/4” pedestal mounted single screw rxtruder. Model DSPW-125V-H24, serial#V9991, SO#61592, built 1998. Approximate 24 to 1 L/D ratio. Electrically heated, water cooled 3 zone non-vented barrel with a closed loop water system, with pump, tank, and heat exchanger. Adjustable centerline height, water cooled feed throat with hopper. Driven by a 5 hp, 180 volt, 1750 rpm DC motor thru an Ex-Cell-O cone drive, ratio 15 to 1. Includes a control panel with Eurotherm controllers, Reliance FlexPak Plus VS drive, and a 6 kva transformer. 1) 7” Wide sheet die, 1) Davis Standard 3 roll sheet stack, with(2) 5” diameter x 10” wide chrome plated cored rolls, 1) 5” diameter x 10” wide cored rubber roll, 2) pull rolls, 1) chrome, 1) rubber, all driven by a 1 hp, 180 volt DC gear motor. ... moreIncludes a Mokon temperature controller, model MM4H04-01, serial#63036, rated 4 kw, maximum temperature 250 degrees F. Mounted on a cart. ref# 44517001 Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780
|
|
|
41817004 Used- Twin Screw Underwater Pelletizing Line consisting of: (1) Berstor
Click To Enlarge- Used- Twin Screw Underwater Pelletizing Line consisting of: 1) Berstorff 40mm twin screw extruder. Model ZE40/40A, serial#EO9454/91. Co-rotating design, no screws. Approximate 40 to 1 L/D ratio. 8 barrel sections, 1 feed section. Hot oil heated and cooled. Approximate 42" centerline height. Driven by a 50 hp, 500 volt, 2500 rpm DC motor thru a reducer. 1) Manual screen changer, 1) 4 hole strand die, 1) control panel with Eurotherm 808 controllers, Reliance VS drive, and an Allen-Bradley AC drive, 1) Berstorff operator panel, Includes(2) Budzar hot oil units. ref# 41817004. Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location ... moreunless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
43198004 Used- Brown Thermoforming Line Consisting Of: (1) used Brown continuous
Click To Enlarge- Used- Brown Thermoforming Line Consisting Of: 1) used Brown continuous thermo former. Model CS-2100, 25"635mm) wide x 26"660MM) long maximum mold size, 6" max draw depth, servo driven platen/index drives with Indramat drives, 40" wide x 108" long oven, Allen Bradley SLC-5/03 controllers, 480 volt, serial# 12566, new 1994 with(1) Brown horizontal trim press, model T130R, 15 ton max compression, 12.5" x 30"318mm x 762mm) stationary platen opening, 17.5" x 34" stamping platen size, 4.5"114mm) 13.5"343mm) stoke adjustment range, 33"838mm) max sheet width, with controls, 480 volt, serial# 12034. ref# 43198004 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: ... moreBensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
42905001 Used- Battenfeld Pelletizing Line Consisting Of: (1) 130 mm Battenfeld
Click To Enlarge- Used- Battenfeld Pelletizing Line Consisting Of: 1) 130 mm Battenfeld counter rotating twin screw extruder. Model BX2-130-25V, 25:1 L/D, electrically heated barrel with 5 barrel zones, 123 kw dc motor with SCR controller, Battenfeld model BMC compact controller, agitated feed hopper, 480 volt, serial# 9528-51. Also includes Reimelt stainless steel delumper, model R57ESP, stainless steel construction, jacketed for 1 bar at 50 C, AZO pellet air dry cooling unit, 5.5 KW, stainless steel construction, 24" diameter x 6' hopper cyclone, 480 volt with approximately 4' diameter x 5' conical discharge hopper. ref# 42905001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. ... moreServices available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
42691007 Used- Crown Single Screw Pelletizing Line Consisting Of: (1) Crown 4-1/
Click To Enlarge- Used- Crown Single Screw Pelletizing Line Consisting Of: 1) Crown 4-1/2" single screw extruder. Approximate 36:1 L/D ratio. Electrically heated, water cooled 6 zone side vented barrel with a closed loop system, with pump, tank, and heat exchanger. Water cooled feed throat, with hopper. Driven by a 150hp, 500 volt, 1750 rpm DC motor thru a NRM gearbox, no ratio. Approximate 44" centerline height. 1) 4-1/2" Hydraulicscreen changer with a 2hp power pack, 1) Beringer 1-1/2hp cutting head, 1) Beringer 3hp spin dryer with water slide, tank, pump, and heat exchanger, 1) control panel with temperature controllers, and a drive, and(1) 175 kva transformer. ref# 42691007 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item ... morelocation: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
42566001 Used- APV Sterling Sheet Line Consisting Of: 6" Sterling extruder, 32:1
Click To Enlarge- Used- APV Sterling Sheet Line Consisting Of: 6" Sterling extruder. 32:1L/D, electrically heated, water cooled barrel with circulation system, 500 hp dc motor, 17.2:1 gearbox ratio, 100 rpm screw speed, 6 barrel zones, 6adaptor, zones, 7 die zones, 4 roll zones, 30 hpgear pump, 6" Berringer hydraulic screen changer, model XR, 94" wide x 8" diameter(4) roll sheet stack, chromed top roll, textured bottom roll, EDI serial# 97-19337-01, Sterling serial# 60455. Process Control 4 material volumetric hopper loader with 25 hp pump. ref# 42566001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the ... moreseller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
42525001 Used- Welex 53" Wide Sheet Line Consisting of: (1) Welex 4-1/2" single
Click To Enlarge- Used- Welex 53" Wide Sheet Line Consisting of: 1) Welex 4-1/2" single screw extruder. Model 450 36:1RHDV, serial# 1269 10-79, approximate 36 to 1 L/D ratio, 6 zone side vented barrel, electrically heated, water cooled with tank, and heat exchanger. Water cooled feed throat, no hopper. Approximate 56" centerline height. Driven by an approximate 250 hp DC motor thru a Welex change gear Herringbone reducer, ratios 11.74/14.01/17.55/23.47 to 1. Includes a control panel with temperature controllers, and a Typact TI drive. 1) 4-1/2" Hydraulic screen changer, no power pack, 1) 44" Wide EDI sheet die, serial# RW-73-5148. 1) Welex 3 roll sheet stack, model 18X53SLRH, serial# 1270 11-79. 3) 18" Diameter x 53" wide chrome plated cored rolls, driven by a 3 hp gear motor. Includes pumps, heat exchangers, ... moreand control panel with a Baldor, and Safetronics drive. 1) 10' Long cooling section, 2) 8" diameter x 53" wide pull roll stand pneumatically adjustable, driven by an approximate 3 hp gear motor. 1) Brown Machine Thermoformer, Model 42P. Approximate forming area 36" x 30" Top and bottom platens. 4 Zone oven, top and bottom preheat oven. Includes a Brown Machine trim press. ref# 42525001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment
|
|
|
42396004 Used- 6" Sterling sheet line consisting of; 6"Sterling extruder, 32:1 L
Click To Enlarge- Used- 6" Sterling sheet line consisting of; 6"Sterling extruder. 32:1 L/D, electrically heated,water cooled barrel with circulation system, 400 hpdc motor, 1750 rpm motor, 17.2:1 gearbox ratio,6 barrel zones, extruder serial#60433, with 30 hp gear pump. 64" wide EDI sheet die, 64" wide x 30"diameter Sterling(3) roll sheet stack ref# 42396004 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale ... moreor other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
40578001 Used- Gloucester 54'' Wide Foam Line consisting of: (1) Glouster 6'' si
Click To Enlarge- Used- Gloucester 54' Wide Foam Line consisting of: 1) Glouster 6' single screw extruder. Model 267-001, approximately 30 to 1 L/D ratio. Electrically heated, water cooled barrel, approximate 42' center line height. Driven by a 200 hp, 500 volt, 1750 rpm DC motor thru a reducer, ratio 41.83 to 1. Includes a die clamp. 1) Glouster 4 1/2' single screw extruder, model 244-001, approximate 24 to 1 L/D ratio. Electrically heated, water cooled barrel, approximate 42' center line height. Requires a motor, reducer, ratio 15.16 to 1. Includes a screen changer. 1) Control panel(incomplete) 1) Safetronics drive panel, tensioning rolls, 225 kva transformer, 54' wide nip roll assembly with(2) 2 hp DC gear motors(missing drive rolls) 2) cooling station rolls with tensioning. ref# 40578001 Contact Information Steven ... moreCohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
40508006 Used- Battenfeld Tandem Foam Extrusion Line consisting of: (1) 4.5" Bat
Click To Enlarge- Used- Battenfeld Tandem Foam Extrusion Line consisting of: 1) 4.5" Battenfled Gloucester extruder. Model 244.001, 36:1 L/D, electrically heated, water cooled, jacketed feed section with 150 hp DC motor with SCR controller, serial#244.29812.01. 1) 4.5" Beringer hydraulic screen changer. 1) 6" Battenfeld Gloucester extruder, model 266.001, 30:1 L/D, electrically heated, water cooled, jacketed feed section, side feed with 150 hp DC motor with SCR control, serial#266.29812.10. 1) Maag melt pump, type 56/56 with 30 hp DC motor, serial#B1297518. 1) 9.5" diameter basket type pipe die. 6) Cooling mandrels, 3) 30" diameter x 40" face, 2) 30" diameter x 36" face, 1) 26" diameter x 12" face on stands. 1) Battenfeld Gloucester dual pull roll stand, model 352PR, with 62" wide pull ... morerolls, pneumatic adjustment with 3 hp DC motor, serial#29312-26. 2) Concept Measurex thickness gauges with panel. 2) Battenfeld Gloucester turret winders, model 160A-FN, single turret dual station, 72" wide, 6" core with 64" wide tension bar pneumatically adjusted, 3/4 hp turret drive, 5 hp winder drive, serial#s 29812-27A& 29812-27B, with SCR controllers and operation panel. ref# 40508006 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment term
|
|
|
40508004 Used- Battenfeld Laminating Line consisting of: (1) Battenfeld Gloucest
Click To Enlarge- Used- Battenfeld Laminating Line consisting of: 1) Battenfeld Gloucester 4 1/2' single screw extruder. Model 244-001, 24 to 1 L/D ratio, electrically heated, water cooled side vented 5 zone barrel. Water cooled feed throat with hopper. Approximate 43' centerline height. Driven by a 150 hp, 500 volt, 1750/2000 rpm DC motor thru a gearbox, ratio 12.45 to 1. Control panel with a Reliance Flexpak VS drive. 1) Beringer 4 1/2' hydraulic screen changer; 1) Maag type 56/56 gear pump, 30 hp DC motor; 1) 54' wide EDI model H-40 Autoflex die on cart; 1) Gloucester 2 roll sheet stack; 2) 16' diameter x 60' long chrome plated cored rolls; 1) 60' wide Magnetic Power Systems web tension control; 1) Ambrit unwinder; 1) Gloucester nip/haul off station; 1) Advantage model TSE-935-4JH6X temperature controller, 9 ... morekW, 70 to 250 deg F, miscellaneous control panels and transformers. ref# 40508004 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers
|
|
|
45119001 Used- Davis Standard Co-Extrusion Line Consisting of: (1) Davis Standar
Click To Enlarge- Used- Davis Standard Co-Extrusion Line Consisting of: 1) Davis Standard 6" single screw extruder. Model 60IN60TPIH, approximate 30:1 L/D ratio, electrically heated, water cooled, non-vented 6 zone barrel with pump, tank and heat exchanger. Water cooled feed, no hopper. Driven by a 250 hp, 500 volt, 1150/1800 rpm DC motor thru a gearbox, ratio 21.8 to 1, approximate 42" centerline height, includes a die clamp. Serial# M-3904, SO# 05568, built 1991. 1) Davis Standard 2.5" single screw extruder, model 25IN25F, approximate 32:1 L/D ratio, electrically heated, air cooled, non-vented 4 zone barrel. Water cooled feed, no hopper. Driven by a 40 hp, 500 volt, 1750/2100 rpm DC motor thru a gearbox, ratio 17.8 to 1, extruder mounted on top of 6" extruder on a swivel includes a die clamp. Serial# M-3908, SO# 05568, ... morebuilt 1991. 1) Davis Standard 1.5" single screw pedestal mounted extruder, model DS-15, approximate 24:1 L/D ratio, electrically heated, air cooled, non-vented 5 zone barrel. Water cooled feed, no hopper. Driven by a 10 hp, 240 volt, 1750 rpm DC motor thru a reducer, ratio 15 to 1. Serial# K5422, SO# 01045, built 1988. 3) Control panels with(1) Eurotherm 590 digital series drive, 1) SSD 590 drive, 1) Texas Instruments System 505 controller. 1) 275 kva transformer, 1) 51 kva transformer, 1) 20 kva transformer, 1) 60 kva transformer, and(1) Operator control panel box only, no controls. ref# 45119001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freig
|
|
|
41682001 Used- Welex 53'' Wide Sheet Line consisting of: (1) Welex 4-1/2'' singl
Click To Enlarge- Used- Welex 53' Wide Sheet Line consisting of: 1) Welex 4-1/2' single screw extruder. Model 450-30, serial#385, approximate 30:1 L/D ratio, approximate 8 zone side vented barrel, electrically heated, air cooled. Water cooled feed throat, no hopper. Approximate 57' centerline height. Driven by a 200 hp, 500 volt, 1750/200 rpm DC motor thru a Welex change gear reducer, ratios 11.74/ 14/ 17.55/ 23.47 to 1. Control panel with Watlow SD temperature controllers and a Safetronics drive. 1) 55" wide EDI sheet die, model UH-100, serial# 05-25154, all 3 mounted on a cart. 1) Welex 3 roll sheet stack. 3) 18" diameter x 53" wide chrome plated cored rolls with pumps, control panel, and 12' long cooling section. 1) Pull roll stand, 2) 8' diameter x 53' wide rubber rolls. 1) 72" wide winder. ... moreref# 41682001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
83113 USED: Baker Perkins 100mm compounding/pelletizing line consisting of: (1)
Click To Enlarge- USED: Baker Perkins 100mm compounding/pelletizing line consisting of: 1) Baker Perkins 100mm co-rotating twin screw continuous mixer. Model MPC/V. 55" long clamshell design barrel, oil heated. Driven by a 125 hp, 500 volt, 1750 rpm DC motor with reducer. 1) Approximately 6" extruder with approximately 100 hole strand die, driven by a 20 hp, 500 volt, 1750 rpm DC motor. 1) Underwater fly knife pelletizer, driven by a 10 hp motor, with water slide. 1) Gala spin dryer, driven by a 5 hp motor. 1) Accurate feeder, 1) Vibranetics model BD8 live bottom hopper and misc pumps. ref# 83113 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the ... moreitem description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
44953002 Used- Leistritz Pelletizing Line consisting of: (1) 34 mm Leistritz tw
Click To Enlarge- Used- Leistritz Pelletizing Line consisting of: 1) 34 mm Leistritz twin screw extruder. Co-rotating screws, 27:1 L/D, electrically heated, air cooled barrel, vented and plugged barrel section, 11 kw(15 hp) variable speed motor, 390 rpm max screw speed with on board temperature control panel, serial#330 168901, new 1989. 1) 3 hole strand die, Acrison gravimetric feeder, model LSM34GL, stainless steel hopper and screw, 2" diameter screw with control. 1) Conair strand pelletizer, model 304, 10 knife solid helical rotor, 2.5 hp, 240 volt motor, serial#6-04096, system includes spare extruder screws, elements, shafts and spare pelletizer rotor. ref# 44953002 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. ... moreIllinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
|
44774001 Used- Leistriz Twin Screw Extrusion Line consisting of: (1) Acrison fe
Click To Enlarge- Used- Leistriz Twin Screw Extrusion Line consisting of: 1) Acrison feeding system consisting of(1) Acison feeder. Type 407-1400-200-101-BB. Including stainless steel bunker, serial#02499-06. 1) Acrison feeder, type 407-500-150-101-DD. Including stainless steel bunker, serial#02499-05. 1) Acrison feeder, type 407-1400-200-101-BB. Including stainless steel bunker, serial#02499-04. 1) Acrison feeder type 407-20-40-101-DD. Including stainless steel bunker, serial#02499-03. 1) Acrison feeder type 407-400-12-101-DD. Including stainless steel bunker, serial#02499-02. New 2002. 1) Novetec vacuum pump, type VPU-10HO, 9.2 KVA, 14 amp. 380 Volt/50 cycle/3 ph motor. On 4 legs. Serial#14-305-2149. New 2002. 1) Extruder vacuum system frame mounted. 1) Leistriz twin screw extruder, type ZSE100-GL-BX. Co-rotating. 44:1L/D. Electrically ... moreheated, water cooled. Max screw speed 400 rpm via a gearbox 4.13:1 by a 660 hp(440 Kw) 420 volt/50 cycle/3 ph/1652 rpm motor. Serial#3048156, new 2002. 10955.9 Hours in service. 1) Leistriz side feeder including feeder. 1 x Melt pump. 1) Control panel, 4 door extruder. 1) Control panel, 4 door extruder. 1) Bag unit. 1 x Measure saw, type 2030. Including Honeywell CPU, type Proline 4625. Including control panel. 1) Cognex 3 x camera inspection unit. Including control panel. ref# 44774001 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and
|
|
|
43752048 Used- Cincinnati Milacron Extrusion Coating Line Consisting Of: (1) 30"
Click To Enlarge- Used- Cincinnati Milacron Extrusion Coating Line Consisting Of: 1) 30" 2) Shaft unwind stand able to handle up to 60" diameter rolls. Set up for approximately 12" ID cores, serial#2470A01/93-4; 1) Novatec model MCS-206 three component blender with receivers and controls, 115/1/60, serial#12-243-0177; 1) Novatec model UPU 3 hp pneumatic conveyor with inline filter with multi-station control panel, serial#12-343-0842; 1) Cincinnati Milacron 2.5" Apex extruder, 34:1 l/d, six zone electrically heated, closed loop water cooled barrel, side vented, Flenders gearbox 10.3:1 ratio, driven by a 75 hp motor with controls, vacuum pump, serial#2406A01/93-5, free standing control panel; 1) 2.5" Beringer SL-25 hydraulic slide plate screen changer; 1) Maag Extrex 45/45 melt pump with 5 hp AC drive system, new 1995, ... moreserial#50013306-10; 1) 32" EDI model H-75 sheet die mounted on a cart, serial# 93-1553; 1) Cincinnati Milacron sheet take-off with 34" face x nominal 18" diameter rolls mounted in a vertical arrangement with temperature control system and pull rolls. ref# 43752048 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description or contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise
|
|
|
45276004 Used-6" PELLETIZING LINE CONSISTING OF THE FOLLOWING: - 6" CROWN 30/1 L
Click To Enlarge- Used-6" PELLETIZING LINE CONSISTING OF THE FOLLOWING: 6" CROWN 30/1 L/D VENTED EXTRUDER INCLUDING 6" HYDRAULIC SLIDE PLATE SCREEN CHANGER. BUT NO HYDRAULIC PUMPING SYSTEM. EXTRUDE IS ELECTRICALLY HEATED AND WATER COOLED, HAS TOP CENTER VENT, INCLUDES TEMPERATURE CONTROL PANEL WITH 15, 1/8 DIN INSTRUMENTS. INCLUDES 500HP MOTOR DIRECT CONNECTED TO GEARBOX. INCLUDES SCR CONTROL. DOWNSTREAM INCLUDES BERINGER MODEL 35S WATER RING PELLETIZING SYSTEM. SYSTEM INCLUDES SLUSHWAY, 3HP AC MOTOR PELLETIZER, AND SPIN DRYER. INCLUDES OPERATOR CONTROL PANEL. ref# 45276004 Contact Information Steven Cohen Aaron Equipment Company 735 E. Green St. P.O. Box 80 Bensenville. Il. 60106 Phone: 630-350-3021 Fax: 630-350-0780 Item location: Bensenville. Illinois, United States. Services available: Freight- Check the item description ... moreor contact the seller for details. Ships to: United States. Seller's payment instructions All items sold are FOB Bensenville. Il. location unless otherwise noted. All items offered are subject to prior sale or other disposition. Base shipment costs $150.00. This cost may vary depending on shipment location and type of freight carrier selected. Prep for each item also will vary Please call for shipping estimates and payment terms. We accept Visa, Master Card, AMEX and wire transfers. Please advise for other payment terms. A 3% Convenience Fee will be charged if paying by credit card.All items sold are FOB Bensenville, Il. location unless otherwise noted. Return Policy: Items paid in full price have a 1 week right of return. 100% refundable, customer pays all freight– unless negociated differently. Payment Details: Company Checks. Wire Transfers, Purchase Orders, Visa/MasterCard, Amex
|
|
 |