|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
$3.00 Shipping Condition: Seller refurbished Location: Northridge, United States 2-Phase Uni-Polar Stepper Motor. Made by Japan Servo. Included: 2 X Precision Stepper Motors with Wires. Pulley Pitch 2mm. Number of teeth 20.
Buy It Now
Free Shipping Condition: New Location: China Feature: 1. DMA860H is a low‑noise digital stepper motor driver with high efficiency. Item Type: Stepper Motor Driver. Motor Interface: A+ and A- are ... moreconnected to the positive and negative ends of the A-phase winding of the stepping motor; B+ and B- are connected to the positive and negative ends of the B-phase winding of the stepping motor.
Buy It Now
Free Shipping Condition: New Location: United States Model Number:DM556D. DM556D Stepper motor drive specification. 1x DM556DDigital Stepper Motor Driver ( 5.6A, 24-50V DC, 256 microstep ). Characteristic:Low ... morenoise, low vibration, low temperature rise. Driver current:5.6A;Driver microstep:256 microstep.
Buy It Now
$15.00 Shipping Condition: New Location: China HSS86 is 2 phase nema 34 series hybrid stepper servo driver. The torque reducing is much lower than open loop stepper motor when it is at higher speed. ... moreThe high speed performance and torque are enhanced in a great extent.
Buy It Now
Free Shipping Condition: New Location: China Model: TB6600. It is an updated version of TB6600 4A stepper motor driver. Feature: 1. Original stepper motor driver chip, the current is selected by ... moreDIP switch. Item Type: Stepper Motor Driver. Common anode single pulse interface standard;.
Buy It Now
Free Shipping Condition: New Location: China Stepper Motor Driver is a board for DRV8825 microstepping stepper motor driver. - DRV8825 driver board is widely used in 3D printers and small CNC machines. ... more5 UEETEK DRV8825 Stepper Motor Driver Module 4-Layer with Mini Heat Sink for 3D Printer.
Buy It Now
Free Shipping Condition: New Location: China The MACH3 interface board is connected to the computer through the USB port and the LPT port. At present, many computer hosts do not have LPT port output. ... moreIf your computer does not have an LPT output, you will need to use a PCI-to-port card.
Buy It Now
$227.00 Shipping Condition: New Location: China Stepper motor driver: DM2722A. 3 pcs Nema 42 stepper motor 4120 oz.in, 8.0A, 4 leads, bipolar 42HS6480. Nema 42 stepper motor. Stepper driver working ... morecurrent is set by DIP-1 switches. l Drive current is adjustable in 16 channels from 1.2A/phase to 7.0A/phase.
Buy It Now
Free Shipping Condition: New Location: Hainesport, United States GRBL 32-bit, stable performance, faster speed and higher accuracy. GRBL 32-bit chip technology Integrated 3 A4988/8825 drivers, directly connect to four ... morewire stepper motor. Support the xyz limit switch, probe interface.
Buy It Now
Free Shipping Condition: New Location: United States This item includes: 2 PCS Nema 23 Stepper Motor single shaft with 270 oz-in.3A holding torque,4 Leads 2 PCS Stepper Driver with 4.2A DQ542MA digital serial ... morereplacing M542, Email： MSN: Skype: happy_saron 1. Stepper Motor Technical Specifications Part No. 57BYGH627 single shaft Frame Size: NEMA23 Step Angle: 1.8 degree Voltage: 3.0VDC Current: 3.0 A/phase Resistance: 1.0 Ohm/phase Inductance: 3.5 mH/phase Holding torque: 19 Kg-cm 270 oz-in Rotor inertia: 480 g-cm2 Detent torque: 0.6 kg-cm Number of wire leads: 4 Weight: 2.20lb( 1.0 kg) Length: 76mm Shaft diamter: 6.35mm(1/4" Black A+ Green A- Red B+ Blue B- Please tell us if you need Double shaft or single shaft. We can manufacture both for you. If you need Double shaft, please tell us your requirements for length of front and rear shaft, as well as the diameter. So that we can offer you the quite good products, thanks! 2. Stepper Motor Driver DQ542MA with 4.2A Current, 128 Microstep DQ542MA is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 18VDC to 50VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver. What’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, Computer embroider machine, packing machines and so on. Features: l High performance. Low price l Average current control. 2-phase sinusoidal output current drive l Supply voltage from 18VDC to 50VDC l Opto-isolated signal I/O l Overvoltage. Under voltage, overcorrect, phase short circuit protection l 15 channels subdivision and automatic idle-current reduction l 8 channels output phase current setting l Offline command
Buy It Now
Free Shipping Condition: New Location: China Integrated 3 A4988 drivers, directly connect to four wire stepper motor. --Support Laser or Spindle. --Support 12V, 5V with TTL and without TTL laser. ... more1 USB Data line. --Support the xyz limit switch, probe interface.
Buy It Now
Free Shipping Condition: New Location: United States CNC Router Single One Axis 3.5A TB6560 Stepper Motor Driver Controller Board SKU:A88# Description TB6560AHQ is the stepper motor driver chip. The chip ... moreis highly integrated, simple peripheral circuits. High reliability, and part of the motor 57 for driving stepping motor 86, when the largest segment range from 0 rpm to a speed of 300 rpm. Features* high integration and high reliability of the stepping motor driver* interface with ultra high speed optical isolators* High anti-jamming capability* The maximum drive current of 3.5A( peak) Main function* whole-step. 1/ 2, 1/ 8, 1/ 16 segments. step by step adjustable current 0.5-3A* Automatic overheat protection* Optional automatic semi- flow* Adjustable current decay fourth gear* LED indicates power and working status* Support for offline. Enable. Lock etc. Package list: 1* Single Axis 3A TB6560AHQ Stepper Motor Driver Board NOTE We try our best to make every transaction perfectly, just for winning your F ive-Star rating. If you have any dissatisfaction. Please contact us. We will give you the most satisfactory results. PLEASE don't leave a neutral or negative easily. Shipping Item will be shipped within 24 hours on payment received from Hong Kong using Airmail. Only shipped to buyer's PayPal address. Please confirm with your PayPal address before you bid. Delivery time depends on destination and other factors. It may takes up to 30 business days. Optionally. Express Shipments with tracking service via EMS/DHL/UPS with a quoted delivery time of 5 to 7 business days is also available. Here is the estimated time for your reference only: Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-25 30 Working Days + Saturday + Sunday 5-9 10-14 15-20 21-25 26-35 40 United States Rate(item arrived) 9% 50% 21% 13% 7% Refund or Resend United Kingdom Rate(item arrived) 10% 62% 20% 3.5% 4.5% Refund or Resend Australia Rate(item arrived) 23% 50% 13% 8% 6% Refund or Resend Europe(Exclude Russia) Rate(item arrived) 2.5% 2
Buy It Now
Free Shipping Condition: New Location: Navarre, United States Minimal pulse width of 2.5μs. Also swapping the connection of two wires of a coil (e.g. A+ and A-) to the drive will reverse motor direction. Enable signal: ... moreThis signal is used for enabling/disabling the drive.
Buy It Now
$3.78 Shipping Condition: New Location: China 1 x Adapter Breakout Board. The output port is P17 port. The output port is P1 port. Connectors: USB(Female)+25PIN(Male). 1 x USB Cable.
Buy It Now
Free Shipping Condition: New Location: United States 3 Axis TB6560 CNC Stepper Motor Driver Board 1.5A-3A*NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller Product Features: Toshiba TB6560AHQ chip- High ... morepower. Maximum 3.5A drive current chipset! 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step, Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors*Attention: This driver is 1.5A-3A version. Which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A. If the rated current your stepper motors is below 1.5A. You can choose the 0.5A-2.5A version. Please let us know which version(1.5A-3A version is default) you need immediately after placing an order. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Deta
Buy It Now
Free Shipping Condition: New Location: Kearny, United States Support XYZ axis, double Yaxis. --the chip internal resistance is smaller, lower heat, better heat dissipation. --4 layer PCB board, better heat dissipation ... moreperformance. --Integrated 3pcs A4988 drivers, directly connect to four wire stepper motor.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. EMA232-7630S4 Nema23 Stepper Motor. • Suitable for 2-phase and 4-phase Hybrid stepper motors. Hybrid Stepper ... moreMotor(EMA232-7630S4). ™ 4 Axis Kit for CNC DIY. 5 Axis Breakout Board.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: Rancho Cucamonga, United States Stepper Drive TB6600. In the user expects low cost, high current operation. Stepper Motor. Can drive 4, 6 and 8 Lead two-phase, four-phase stepper motor. ... moreSignal input: single ended, pulse / direction.
Buy It Now
$1.76 Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. Color: See pictures.
![]()
Buy It Now
Free Shipping Condition: New Location: United States 4 Axis CNC 3.5A TB6560 Stepper Motor Driver Board Controller F Engraving Machine. Click To Enlarge CNC stepper motor driver board 96560A V1 adopts the ... morenew chip TB6560AHQ of TOSHIBA. The max ouput current can reach to 3.5A, this driver board can drive the 2-phase or 4-phase stepper motor whose current is less than 3A. The advantages of the TB6560AHQ chip: The vibration of the motor is small and low noise: because of the 2/8/16 resolution can satisfy the different speed. Flush type low heat: The area of the chip can support itself to cool when the current is low Supports a lot of stepper motors The advantages in the high-speed running condition board might be made partly out of recycled parts. Because of the environmental protection Features: 4-wire 0-3.5A(normally 3A. The 3.5A is the peak current)can be regulated rate current output, bipolar stepper motor driver Standard parallel port. Supports Mach 2, KCAM 4 etc. Optical isolated(IO) and DCDC power isolated to protect the PC parallel port and other equipments Limit and emergency stop port( standard DB9 port) 4 working modes: mixed mode. Fast mode, slow mode, standard mode 4-resolution: 1 1/2 1/4 1/16 12-36V single power input uses the switch power chip as the 5V power supply. Stable and low heat Adopts RC + 7414 auto semi-flow The relay output can control the main axis 5th axis extension control port Packing list: 1* 4 Axis CNC TB6560 Stepper Motor Driver Board 1* DB25 Parallel Male- F emale Cable 4* Connect Terminal A997A NOTE We try our best to make every transaction perfectly, just for winning your F ive-Star rating. If you have any dissatisfaction. Please contact us. We will give you the most satisfactory results. PLEASE don't leave a neutral or negative easily. Shipping Item will be shipped within 24 hours on payment received from Hong Kong using Airmail. Only shipped to buyer's PayPal address. Please confirm with your PayPal address before you bid. Delivery time depends on destination and other factors. It may takes up to 30 business days. O
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States This system is built around the Gecko Drive G540 digital integrated micro stepping 4 axes driver system. I also include the required resistors for the ... moreG540. Gecko G251x Driver Myths.16ft Table Run With Gecko G540 Drivers.
Buy It Now
$3.59 Shipping Condition: New Location: China 1 x Adapter Breakout Board. The output port is P17 port. The output port is P1 port. Connectors: USB(Female)+25PIN(Male). 1 x USB Cable.
Buy It Now
Free Shipping Condition: New Location: Bordentown, United States The drive current: 2A (best to install the heat sink). 10 Heatsink.
Buy It Now
$11.60 Shipping Condition: New – Open box Location: Alma, United States Microstep Driver Stepper Motor CNC Controller 4A DC9-40V for for Nema 17/23/16.
Buy It Now
$17.80 Shipping Condition: New – Open box Location: Fond Du Lac, United States 57BYGH Stepper Motor is a high-torque, low-inertia stepper motor that can rise quickly. It is an available option for drivers, wiring harnesses, flexible ... morecouplings and dampers. Step angle (°). Temperature Rise…………………………………………80℃ Max.
Buy It Now
$4.35 Shipping Condition: New Location: China CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board, Photo: Description: Features: Working voltage DC 10V-35V. Recommended ... moreto use a switching power supply DC24V power supply. 6N137 high-speed optical coupling. Guarantee high speed without losing step. using the Toshiba TB6560AHQ new original chip with low voltage shutdown. Overheating stop and overcurrent protection circuit to ensure optimal performance. Rated maximum output: ± 3A. Peak 3.5A. for two-phase within 42.57 stepping 3A/ four-phase/ of line four/ six-wire stepper motor, and is not suitable for more than 3A stepper motor. automatic half current function. subdivision: whole step. Half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions. Dimensions: width 50* 75* long high-35(MM) Features similar products: 1. Current grade-by-adjustable to meet your demand for a variety of applications. 2. Semi-automatic flow adjustable. 3 6N137 high-speed optical coupling. Guarantee high speed without losing step. 4. Plate printed setup instructions operation without manual also. 5. Thick teeth radiator, good heat dissipation. Absolutely use Toshiba TB6560AHQ. New original chip, a penalty at ten! Package Contents 100% Brand New 1x TB6560 3A driver board, Shipping: We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! Ship by Post Air-mail within 1 working days after full payment is received. The shipment usually takes 12-35 business days to Worldwide. We also provide international Expressed delivery such as EMS. DHL and UPS,extra shipping fees is needed. The shipping time may vary. Depends on receiver's location. Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-22 25 Working Days + Saturday + Sunday 5-9 10-14 15-20 21
Buy It Now
Free Shipping Condition: New Location: Castle Rock, United States Arduino compatible. 15 x Stepper Motor Drivers A4988T. 15 x A4988T Stepper Motor Driver. TTL Compatible. Raspberry Pi Compatible. Plug and play. A4988 ... moreDriver Shield. Upon the closing of an unpaid claim, the item will be relisted for sale and the existing sale will be cancelled.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China It can effectively solve the problem of air-assisted yellowing wood boards. Cutting/air assisted opening, engraving/air assisted closing can be realized. ... more1 × 32 bit auto air assist main board +installation box.
Buy It Now
Free Shipping Condition: New Location: China For 42, 57 3A stepper within two-phase / four-phase / four-wire / six-wire stepper motor is not suitable for more than 3A stepper motor. The maximum rated ... moreoutput: ± 3A, peak 3.5A. Using a fine-toothed thick radiator, good heat dissipation.
Buy It Now
$3.00 Shipping Condition: New Location: China It is suitable for driving 2-phase and 4-phase hybrid stepping motors. - 1 x Stepper Motor Driver. - Output current up to 7.2A. - Good high speed performance. ... more- Suitable for 2-phase and 4-phase motors.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 3 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. 3 pcs Stepper motor driver, peak 7.8A 24-80VDC. Nema 34 stepper motor Hording torque ... morewhen DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$2.99 Shipping Condition: New Location: China Applicable to all versions of mach3 software;. Current:＞500MA. 1x USB Cable. DC 5V-15V Frequency Square Wave Pulse Generator Oscillator Output Signal ... moreSource. 1hz-150Khz Signal Generator Module Square Wave PWM Pulse Frequency Duty Ratio.
Buy It Now
Free Shipping Condition: New Location: China 1 x DMA860S Stepper Motor Driver. DC18V—160V;. protection,motor phase open circuit detection and other functions;. function,which can be directly connected ... moreto the input signal,Instead of. ※ Optically isolated differential signal input, the maximum input pulse frequencyis 300KHz;.
Buy It Now
Free Shipping Condition: New Location: Washington, United States The DM542 digital stepper motor driver adopts the latest 32-bit DSP technology, suitable for driving 57 and 86 series motors. Compared with other traditional ... morestepper motor drivers, it has less noise, less thermal power and smoother drive process.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 4 pcs Nema 34 stepper motor 1600 oz.in bipolar with single Shaft. Nema 34 stepper motor Stepper motor driver--DM860A Hording torque when DM860A run under ... morehigh speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. First Automation. Due to the difference between different monitors, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: New Location: Brentwood, United States This high subdivision driver is suitable for high subdivision motor. Suitable for stepper motor: 42,57,86 type 2-phase 4-phase (4-wire, 6-wire, 8-wire).
Buy It Now
Free Shipping Condition: New Location: China 1 x Stepper Motor Driver 1 x Heat Sink 1 x Screwdriver. Bike Brake Bleed Tool Kit Bicycle Oiler Bleeder Bikes Oiling. UEETEK 5 Pcs DRV8825 Stepper Motor ... moreDriver Module 4-Layer with Mini Heat Sink. - Material: PCB.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Digital Hybrid Microstepping Driver(EMA2-050D56). Digital Hybrid Microstep Motor DriverEMA2-050D56 for Stepper Motor. ™ digital hybrid stepper driver ... moreis a high performance Microstep Motor Driver adopting32-bit DSP, pure sine wave subdivision technology.
Buy It Now
Free Shipping Condition: Used Location: Carpinteria, United States Welcome to have a look at my store. We offer a variety of different RC parts and RC tools that you may interest in. APM V2.8.0 ArduPilot UAV Flight Controller ... morewith Power Module& Mini OSD(CNC Case) for FPV Multicopter Airplane description: This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version. And change it into DF13-4P I2C external compass interface. Put DF13-5P GPS interface with external compass interface. Convenient for the connection of GPS and externalcompass. V2.52 I2C interface changes to multifunctional MUX interface- Modified version added isolation resistor. When the OSD interface used with telemetry, the interfaces is effectively avoided- V2.52 version 3.5V power supply adopts IPS79133. 6V withstand voltage, output current 100mA, need to supply power for six IC, slightly inadequate power supply ability, easy to be burnt dwon. The new version adopts US LP2985-3.3. 16V withstand voltage, more reliable, redcucing the possibility of Bad Gyro health Flight Controller- Needle: staight- Power supply: LP2985-3.3- Max voltage: 16V- Add a 47uF tantalum capacitor- Port: MUX(UART0. UART2, mnnI2 and OSD are optional, OSD is the defaulted output) Description: PM function: used for detecting battery voltage and current. Flight control board receives these two signals, calculating battery remaining power, and remaining flying time- This module has BEC function. Can output 5.3V DC, max 3A continuous current, supply stable power for flight control board- The signal cable connector adopts Japan original connector. Making the connection reliable- The APM 2.5 Power Module is a simple way of providing your APM 2.5 with clean power from a LiPo battery as well as current consumption and battery voltage measurements. All through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with Deans connectors. And wrapped in shrink tubing for protection. Description: APM Minim OSD V1.
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Ship from German warehouse! 3AXIS Nema34 Stepper Motor 1600oz-in 3.5A& driver CNC Router or Mill Great News for European customers! Our products are ... moreshipped from German warehouse directly. after payment. Within 3 ~5 business days for receiving products! Easy to custom clerance, no damage, better service, please don't hesitate! What's in Box? 3 PCS Nema 34 Stepper Motor with Single shaft 1600oz-in holding torque, 3 PCS Stepper Driver DM860A with 7.8A replacing MD882, 3PCS Power Supplies for 35 0W.60VDC, 1 PC Breakout Board, 1 PC DB25 Cable 1.Nema 34 stepper motor: Model Step angel( °) Motor Length L(mm) Rate Voltage(V) Rate Current(A) Phase Resistance( Ω) Phase Inductance(mH) Holding Torque(oz.in) Lead Wire(NO. Rotor Inertia(kg. c? Motor Weight(kg) 34HS5435C-37B2 1.8 151 5.7 3.5 1.9 22 1600 4 3.6 5 2.Stepper motor driver: Detailed pic: Technical Specification: 1. Stepper motor driver DM860A: Http:www.longs-motor.com/ProductsView.asp?id=273&pid=83 Introduction: DM860A is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: L High performance. Low price. L Average current control. 2-phase sinusoidal output current drive. L Supply voltage from 24VDC to 80VDC. L Opto-isolated signal I/O. L Overvoltage. Under voltage, overcorrect, phase short circuit protection. L 14 channels subdivision and automatic idle-current reduction. L 8 channel
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Set Professional ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China 1 x 5Axis Mach3 Breakout Board & USB Cable & Parallel Cable. Stepper Motor. VFD kits, servo motor and servo drive kits, stepper motor and stepper drive ... morekits, ball screw, linear guide. The output port is P17 port.
Buy It Now
$2.99 Shipping Condition: New Location: China CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board, Photo: Description: Features: Working voltage DC 10V-35V. Recommended ... moreto use a switching power supply DC24V power supply. 6N137 high-speed optical coupling. Guarantee high speed without losing step. using the Toshiba TB6560AHQ new original chip with low voltage shutdown. Overheating stop and overcurrent protection circuit to ensure optimal performance. Rated maximum output: ± 3A. Peak 3.5A. for two-phase within 42.57 stepping 3A/ four-phase/ of line four/ six-wire stepper motor, and is not suitable for more than 3A stepper motor. automatic half current function. subdivision: whole step. Half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions. Dimensions: width 50* 75* long high-35(MM) Features similar products: 1. Current grade-by-adjustable to meet your demand for a variety of applications. 2. Semi-automatic flow adjustable. 3 6N137 high-speed optical coupling. Guarantee high speed without losing step. 4. Plate printed setup instructions operation without manual also. 5. Thick teeth radiator, good heat dissipation. Absolutely use Toshiba TB6560AHQ. New original chip, a penalty at ten! Package Contents 100% Brand New 1x TB6560 3A driver board, Shipping: We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! Ship by Post Air-mail within 1 working days after full payment is received. The shipment usually takes 12-35 business days to Worldwide. We also provide international Expressed delivery such as EMS. DHL and UPS,extra shipping fees is needed. The shipping time may vary. Depends on receiver's location. Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-22 25 Working Days + Saturday + Sunday 5-9 10-14 15-20 21
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Holding torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver. Great News from Longs motor!
Buy It Now
Free Shipping Condition: New Location: China Integrated 3pcs TMC2208 drivers, directly connect to four wire stepper motor. for Laser Engraving machine, Drawer Machine, CNC Engraving Machine etc. ... more--Support the x/y/z limit switch, probe interface.
Buy It Now
Free Shipping Condition: New Location: United States 3x Nema24 3.3Nm/467 Oz-in 60BYGH100-401A Stepper Motors. The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency ... moreTB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
Buy It Now
Free Shipping Condition: New Location: San Bernardino, United States Included Components 1 pcs TB6600. ✿The largest 32 subdivision of the 6 models are optional; Suitable for 4Wires, 6 wires and 8 wires stepper motor. The ... moremaximum 4.0A of the eight kinds of output current.
Buy It Now
Free Shipping Condition: New Location: United States 【USA】3 Axis Nema23 stepper motor 3A/425oz. 1 x CD include English user manual and usbcnc software. 4 Axis USBCNC breakout board. This interface board ... moreis based on USBCNC MK1 and just use in our provide softwareand function, can not support update the firmware and use other versions of the software and function.
Buy It Now
$11.60 Shipping Condition: New – Open box Location: Broomfield, United States Designed to work well with the probing features in the new MSM (MachStdMill) screen set. This together with Jumbo mode makes it possible to drive up to ... more6 motors with one parallel port. New features of the PMDX-126 Rev C.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Latest News: Congratuation! Our company Longs Motor has an warehouse in US from September.2012. Great News! SHIP FROM USA WAREHOUSE! for 2nd Anniversary ... morePromotion for US warehouse just for USA BUYERS， Only 15 sets for Promotion! This item includes: 3pcs Dual shaft Nema 34 stepper motor.878oz. in,bipolar 3pcs Stepper motor driver DM860A. Peak 7.8A, 256 Micsteps 3pcs Power Supply 200Watts 60VDC 1 pc Breakout Board& Parallel cable( free offering when you buy all above) Detailed information. 1. Nema 34 stepper motor: Model Step angel( °) Motor Length L(mm) Rate Voltage(V) Rate Current(A) Phase Resistance( Ω) Phase Inductance(mH) Holding Torque(oz.in) Lead Wire(NO. Rotor Inertia(kg. c? Motor Weight(kg) 34HST9805-02B2 1.8 98 6.4 2 3.2 15 878 8 1.7 3 2.Stepper motor driver: Detailed pic: Technical Specification: 1. Stepper motor driver DM860A: Introduction: DM860A is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: L High performance. Low price. L Average current control. 2-phase sinusoidal output current drive. L Supply voltage from 24VDC to 80VDC. L Opto-isolated signal I/O. L Overvoltage. Under voltage, overcorrect, phase short circuit protection. L 14 channels subdivision and automatic idle-current reduction. L 8 channels output phase current setting. L Offline command input terminal. L Motor torque is related with speed.
Buy It Now
$25.00 Shipping Condition: New Location: United States Holding torque when DQ420MA driver runs at high speed is also significantly higher than other two-phase drivers, what’s more, the positioning accuracy ... moreis also higher. 2 PCS Nema 17 Stepper Motors with 4800g.
Buy It Now
$2.99 Shipping Condition: New Location: China Electrical input signal is TTL compatible. Max Drive Current : 4A. Bipolar constant current chopper. Stationary current is automatically reduced by half.
Buy It Now
Free Shipping Condition: New Location: Lincoln, United States Assembled CNC Shield with 4 A4988 (2A) Driver Modules. 4 - A4988 (2A) Driver Modules. 4 - Heat Sinks for A4988 Driver Modules. 1 - Assembeled CNC UNO ... moreShield. Our goal is to resolve any issue as quickly as possible.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 23HS8430 1.8 76 3 3 1.0 3.5 270 4 480 0.68 1. 3 Axis Driverbaord TB6560. Phase Inductance (mH) Holding Torque (oz.in) Lead Wire (NO.). Rotor Inertia (g.cm2) ... moreDetent Torque (kg.cm) Motor Weight (kg). 3 pcs Nema 23 stepper motor 270 oz.in,3A, bioplar, 4 leads.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: United States 1PC Nema 34 Stepper Motor with 1600oz-in holding torque for Dual shaft,3.5A. 1PC Stepper Driver with 7.8A DQ860HA. 1, Stepper Motor. 2, Stepper Motor ... moreDriver DQ860HA. Step Angle: 1.8 degree. The DQ860HA is an economical microstepping driver based on patented technology of Wantai Motor.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China Package Included : 3 x Integration Drive+Motor 1 x Power Supply S-400-36 1 x 5 Axis Mach3 interface board 1 x 25Pin Cable(White or Black) 1 x USB Cable ... moreApplications Area : ToAuto Integrated Closed Loop Motors can be adopted to upgrade performance of stepper systems, or replace many traditional brushless servo systems. Their unique features make them ideal solutions especially for applications requiring low costs, high torque, quick response & acceleration, quick settling time, closed loop control, small installation space, such as electronic dispensing machines, semiconductor equipments, CMM measuring, medical devices, high performance CNC routers / mills / laser engravers, scientific lab instruments.
|
|
|
 |