|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
$5.35 Shipping Condition: New Location: Villa Park, United States Communication interface is a standard SPI interface. - Support Micro SD Card, Micro SDHC card (high-speed card). - Level conversion circuit: micro SD ... morecard into the direction of signals into 3.3V. - The level conversion circuit board that can interface level is 5V or 3.3V.
Buy It Now
Free Shipping Condition: New Location: China warmly welcome to our store.We do retail and wolesale,pls.shopping with confidence! any questons pls.contact us by ebay message. Warmly welcome to our ... morestore。 Description: TEA5767 ARDUINO radio module radio module Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Power: 5V Board size: 31 X 30 MM With a power reverse protection diode Board with a power output filter inductor Multiple filter capacitor combination Blue power indicator You can directly plug the antenna port I2C bus communication Philips company dedicated chip module TEA5767 FM FM Board adopts Philips headphone amplifier chip companies as audio amplifier TDA1308 Onboard 3.5MM audio interface can be directly connected to the headphone amplifier and so on. And single-chip communications as long as the power to pick and two I2C communication lines can be. Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off package included: 1pcTEA5767 FM Radio Modul
Buy It Now
Free Shipping Condition: New Location: United States 2.Multi-style, AM/FM hand tuner model and FM band stereo digital tuning model can be selected. DIY kit bulk contains a variety of electronic components, ... moreyou can learn electronic circuits, develop hands-on skills.
Buy It Now
Free Shipping Condition: New Location: China 1 Set For Arduino R3 Entry Level Learning Kit. Analog Input Pins:6. DC Current for 3.3V Pin:50mA. DC Current per I/O Pin:20mA.
Buy It Now
Free Shipping Condition: New Location: Matthews, United States warmly welcome to our store.We do retail and wolesale,pls.shopping with confidence! any questons pls.contact us by ebay message. Warmly welcome to our ... morestore。 Description: TEA5767 ARDUINO radio module radio module Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Power: 5V Board size: 31 X 30 MM With a power reverse protection diode Board with a power output filter inductor Multiple filter capacitor combination Blue power indicator You can directly plug the antenna port I2C bus communication Philips company dedicated chip module TEA5767 FM FM Board adopts Philips headphone amplifier chip companies as audio amplifier TDA1308 Onboard 3.5MM audio interface can be directly connected to the headphone amplifier and so on. And single-chip communications as long as the power to pick and two I2C communication lines can be. Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off package included: 1pcTEA5767 FM Radio Modul
Buy It Now
Free Shipping Condition: New Location: Fort Collins, United States Fully compatible with Arduino. HC-05 6-Pin Bluetooth Wireless RS-232 Master / Slave RF Transceiver Module. This HC-05 Bluetooth RF transceiver module ... morecan be set as a transmitter or receiver. It can easily transfer data wirelessly, without complex PCB layout or deep knowledge in the Bluetooth software stack.
Buy It Now
Free Shipping Condition: New Location: Indianapolis, United States It is pin compatible with enhanced stability and a better antenna. The ESP-12F module is a shielded breakout board that combines the ESP8266 with 4MB ... moreof flash and a PCB antenna. The ESP-12F is an improved version of the 12E.
Buy It Now
Free Shipping Condition: New Location: Indianapolis, United States Unsoldered pin headers for maximum versatility. The ESP32 is a low cost MCU with 802.11n WIFI and Bluetooth capability. Interfaces: UART, SPI, SDIO, I2C, ... moreLED PWM, Motor PWM, I2S, IR, pulse counter, GPIO, capacitive touch sensor, ADC, DAC, Two-Wire Automotive Interface (ISO-11898-1 compatible).
Buy It Now
Free Shipping Condition: New Location: China •Part of second-hand products will have obvious scratches on the surface. We promise try our best to help solve any problem.
Buy It Now
Free Shipping Condition: New Location: Englewood, United States 433Mhz Radio Link RF transmitter & Receiver Remote Module Kit. 1 x 433Mhz Transmitter. 1 x 433Mhz Receiver. Door bell sensor. Send and receive data from ... moreremote sensors. Receiver Frequency. Garage door sensor.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States FT232RL FTDI USB 3.3V 5.5V to TTL Serial Adapter Module for Arduino Mini Port Description Feature: 100% Brand new and high quality. Material: PCB + Electronic ... moreComponent Support 3.3V. 5V Main Color: Red Chipset: FT232RL USB power has over current protection. Using 500MA self-restore fuse RXD/TXD transceiver communication indicator Pin definition: DTR.RXD,TX,VCC,CTS,GND Pitch:2.54mm Module Size: About 36mm(length)17.5mm(width) Package Included: 1 x FT232RL USB to TTL Serial Adapter Module Shipping& Handing 1. All items will be shipped to buyer's ebay address. Before you pay. Please make sure your address in ebay matches the address you would like us to ship to. 2. We ship within 2 business days(weekends and public holidays are not cognized as business days) after full payment is received and cleared. Generally. Delivery time is 2-4 weeks. 3. As there are weight and cubage restrictions on international order. We are unable to offer you any discount or combined shipping for multiple items. All items are shipped separately. There is no local pickup service. No third party shipping carrier will be used. 4. Import duties. Taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Payment Policy 1. We only accept payment by Paypal. 2. Please make sure you PayPal account is valid prior bidding. 3. Great appreciate for prompt payment. Unpaid item will be filed without receiving payment in 7 days after listing ended. Return Policy 1. We are committed to give you the best customer service possible. If for any reason you are dissatisfied with a purchase. Please contact us and we'll assist you with a prompt solution. We'd like to settle any problem in a friendly manner. 2. We want to make sure you are happy with our item. If for any reason you wish to return the item. Contact us within 14 days from the delivery date and we
Buy It Now
Free Shipping Condition: New Location: China Description. Maximum operating speeds up to 2Mbps. GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control ... moreapplications. 125 Channels. Multi-point communication and frequency hopping to meet the communication needs Built-in hardware CRC error detection. Multipoint communication address control. Low-power 1.9 ~ 3.6V. Only 1uA on Power down mode Built-in 2.4Ghz antenna Available software to set the address. Only received local Address when output data(Provide interrupt instruction) can be directly connected to a variety of microcontrollers, Software programming is very convenient. Built-in voltage regulator Standard DIP Pitch Interface for embedded applications size: 34mm X 17mm X 1mm Package Included: 1 x Arduino NRF24L01+ 2.4GHz Wireless Transceiver Module New. Preview. Engineered for professional eBay sellers！ On Jan-03-15 at 00:11:01 PST. Seller added the following information:
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
$2.99 Shipping Condition: New Location: China Support USB download and Power. 1 pairs of TTL level serial transceiver ports RX / TX. 14 Digital input / output ports: TX, RX, D2 ~ D13. Note: it is ... moreDiy Kit!
Buy It Now
Free Shipping Condition: New Location: United States No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, ... moremouse, joystick, etc. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V.
Buy It Now
Free Shipping Condition: New Location: United States Support USB download and Power. 1 pairs of TTL level serial transceiver ports RX / TX. We will be happy to resolve any issues you may have in a cordial ... moreand friendly manner. 8 analog inputs ports: A0 ~ A7.
Buy It Now
Free Shipping Condition: New Location: China Item Description: New design with Best quality. Mini version.More convenient to use. 1. Chip board ENC28J60/SS. 2. The board 25MHZ crystal. 3. The network ... moreinterface board HR911105A. 4. 3.3V power supply pin. 5. Size: 48.8(mm) x 18.5(mm) Maybe you need it: ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC From Hong Kong. We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The arrival time is 5-20 business days to United States usually. We ensure dispatch the item within 1-2 business days. However. You bought the item from opposite side of the earth, so it needs a little longer time to deliver. Please place order only if you agree with the shipping time and all the terms below. Customs duty is obligation and liability of a citizen in your country. So buyer should be responsible for any tax and custom duty incurred. Generally, the delay or failure delivery is sometimes caused by the policy of different customs. For example, Laser Pointer is unacceptable in some countries. Therefore, please double check your local customs policy carefully before purchase. Or, we will NOT be responsible for any failure delivery related destination customs issue. We accept PayPal only. Payment must be received in 5 business days of auction closing. Please leave note for your special request(e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment. Because most of orders will be processed instantly and same day dispatched. If the item is defect when you receive it or you are not satisfied with it. Please return it within 14 days for a replacement or money back. But the items
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Support 14443A compatible transponder signals. The digital part handles ISO14443A framing and error detection. This module can be loaded directly into ... morea variety of readers molds. Chip: MFRC-522 RC522.
Buy It Now
Free Shipping Condition: New Location: Milner, United States Automation & Linear Motion. Light Sensor. Sound Sensor. Rain Sensor. 1605 Ballscrews, Ballnuts + Housings and Motor Couplings. 15mm Linear Rail + Bearings ... moreHGR15. Also potentially of interest.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
$3.40 Shipping Condition: New Location: China 4-Channel Optocoupler Isolation Module. 1 x PC817 8 Channel Optocoupler Photocoupler Phototransistor Module for Arduino. It uses the PC817 optoisolator. ... moreGreat for use in noisy circuits where signal lines require electrical isolation.
Buy It Now
Free Shipping Condition: New Location: China warmly welcome to our store.We do retail and wolesale,pls.shopping with confidence! any questons pls.contact us by ebay message. Warmly welcome to our ... morestore。 Description: TEA5767 ARDUINO radio module radio module Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off Frequency range from 76-108MHZ automatic digital tuning. High sensitivity. High stability. Low noise. Radio module. A low-power FM stereo radio tuner electrical circuit. The internal integration of the IF frequency selection and demodulation network. Can be completely free transfer. High sensitivity( using a low-noise RF input amplifier) Frequency range from 76-108MHZ High-level radioactive AGC(AGC) circuit LC tuned oscillator with low-cost fixed chip Select in-house FM IF. IF free transfer Power: 5V Board size: 31 X 30 MM With a power reverse protection diode Board with a power output filter inductor Multiple filter capacitor combination Blue power indicator You can directly plug the antenna port I2C bus communication Philips company dedicated chip module TEA5767 FM FM Board adopts Philips headphone amplifier chip companies as audio amplifier TDA1308 Onboard 3.5MM audio interface can be directly connected to the headphone amplifier and so on. And single-chip communications as long as the power to pick and two I2C communication lines can be. Phase-locked loop tuning system Soft mute. Stereo noise canceling(SNC) high cut(HCC) through the bus off package included: 1pcTEA5767 FM Radio Modul
Buy It Now
$5.35 Shipping Condition: New Location: Villa Park, United States Transmitter Speed: 4 KB/S. Transmitter Power: 10 mW. Antenna: 25 cm Single core wire or multi-core wire. Frequency: 433 Mz. Working mode: AM. Size: 19 ... more19 mm.
Buy It Now
Free Shipping Condition: New Location: Glen Burnie, United States Title : NRF24L01+ PA LNA SMA Antenna 2.4GHz Wireless Transceiver Module for Arduino. 2 x NRF24L01+ PA LNA SMA Antenna Wireless Transceiver Module. Orders ... moreare typically processed within 24 hours. Enhanced Performance : Features a built-in power amplifier (PA) and low noise amplifier (LNA) for improved transmission range and signal sensitivity.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States 1 x Mini MP3 Player Module U-disk TF SD with Simplified Output Speaker for Arduino. Fully support FAT16. FAT32 file system. the maximum support 32G TF ... morecard. support 32G U disk. 64M bytes of NORFLASH.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Design: 3x4 matrix(0-9, , # ). 12 buttons matrix. Main color: Black. Fit for professional prototype, hobby or university electronics projects.
Buy It Now
$3.50 Shipping Condition: New Location: China Raspberry Pi. ESP-WROOM-32 is a universal WiFi BT BLE MCU module, powerful and versatile. Product Introduction. 1/2/5/10 Pieces.
Buy It Now
$3.50 Shipping Condition: New Location: China Supported by Arduino IDE V1.0.1. Micro USB/ Type-C interface programming (optional). We will be happy to resolve any issues you may have in a cordial ... moreand friendly manner. Four 10-bit ADC pins. 12 digital I/Os (5 PWM capable).
Buy It Now
$3.50 Shipping Condition: New Location: China 1/2/5/10X River Table Module. The light strip needs to be equipped with a 5V light strip. 1/2/5/10X module. Easy to use, easy to operate, and ready to ... moreuse when connected and powered on;. The maximum load can be connected to any light strip within 5V 2A current;.
Buy It Now
Free Shipping Condition: New Location: United States Note:It's HC-06 Bluetooth module. Compatible with bluetooth master module"、slave module"or master-slave(whole) module. Allows your device to both send ... moreor receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
Buy It Now
Free Shipping Condition: New Location: Indianapolis, United States The ESP-12F module is a shielded breakout board that combines the ESP8266 with 4MB of flash and a PCB antenna. The ESP-12F is an improved version of the ... more12E. It is pin compatible, with more stable output and a better antenna.
Buy It Now
Free Shipping Condition: New Location: Fort Collins, United States The communication interface is a standard SPI interface. MISO, MOSI, SCK: SPI bus. Supports Micro SD and Micro SDHC cards (high speed card). The level ... moreconversion circuit board can interface with 5V or 3.3V levels.
Buy It Now
$2.99 Shipping Condition: New Location: China Are the I / O pins exhausted?. On board 3.3V level converter circuit, if you don't solder pad of VCC-VDD, the PCF8575 level is 3.3V. Open drain interrupt ... moreoutput pin for input change interruption.
Buy It Now
Free Shipping Condition: New Location: Fort Collins, United States RST output/push button reset debounce input. Clock accuracy: 0-40, accuracy 2ppm, annual error about 1 minute.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Design: 4x4 matrix(0-9, , #, A,B,C,D ). 16 buttons matrix. Main color: Black. Fit for professional prototype, hobby or university electronics projects.
Buy It Now
Free Shipping Condition: New Location: China 40PCS 2.54MM Dupont Wire Cable Female to Female Male to Female Male to Male, Description Description: 40pcs dupont cables. Durable and reusable. High ... morequality and in good working condition. Easy to install and use. A popular choice for construction or repair. Be used for Arduino breadboard. Features: Quantities: A row of 40 roots. Header:female to female. Male to female, Male to Male. Compatible with 2.54mm spacing pin headers. Length: Approx. 10cm. Package Included: 1* Row of 40pcs jump wire. Related Product. Please click the below link to buy: US $6.58 Free shipping US $8.49 Free shipping US $1.39 Free shipping US $4.38 Free shipping US $6.99 Free shipping US $19.98 Free shipping ++ Payment ++ ++ Shipping terms ++ ++ Return policy ++ ++ Feedback ++ ++ Contact us ++ We only accept payment through Paypal. we hope you can pay them within three days. Please kindly note that if. Within 7 working days, we have not received your payment. we will send a request to the eBay Solution Center(this may cause us to cancel this transaction) But also there are some reasons.Then please let us know. Item will be shipped by air mail. It will need about 11-23 Days to arrive because of some unexcept reasons on the long way. So if you have not receive the items within four weeks.Please feel free to cantact us at first. We will solve that ASAP. Thanks for your patience. Country. Delivery Time. Working Days. 5-7. 8-11. 12-14. 15-19. 20-22. 22. Calendar Days. 5-9. 10-15. 16-20. 21-25. 26-30. 31. United States. Rate of Delivery. 5.1% 50.1% 29.6% 10.5% 4.7% Refund. United Kingdom. Rate of Delivery. 9.9% 63.2% 19.1% 3.4% 4.4% Refund. Australia. Rate of Delivery. 21.4% 50.0% 14.3% 7.2% 7.1% Refund. France. Rate of Delivery. 10.5% 28.6% 43.8% 10.1% 7.0% Refund. Germany. Rate of Delivery. 11.1% 22.2% 30.3% 20.9% 15.5% Refund. Canada. Rate of Delivery. 0.0% 47.1% 31.4% 17.6% 3.9% Refund. If you are not satisfied with the item. Please contact with us. We will offer Full Refund to you when we receive your r
Buy It Now
Free Shipping Condition: New Location: Fort Collins, United States It featuresan SPI interface via the file system driver to read and write files. The communication interface is a standard SPI interface. MISO, MOSI, SCK: ... moreSPI bus. Supports Micro SD(
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States MAX485 chip is a low power consumption for RS-485 communication, limit the slow rate transceiver. Size: 46 (mm) x12(mm).
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: United States Note:It's HC-06 Bluetooth module. Compatible with bluetooth master module"、slave module"or master-slave(whole) module. Allows your device to both send ... moreor receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Communication interface is a standard SPI interface. Support Micro SD Card, Micro SDHC card (high-speed card). Micro SD card connector: yes, Since the ... morebomb deck for easy card insertion and removal.
Buy It Now
$2.99 Shipping Condition: New Location: China PCF8591 AD / DA Conversion of Analog to Digital /Digital-to-Analog Converter Module Temperature Illumination Acquisition. AOUT chip DA output interface. ... moreAINO chip analog input interface 0. AIN1 chip analog input interface 1.
Buy It Now
$3.99 Shipping Condition: New Location: Clementon, United States 1pcs Vishay TSOP4838 38kHz Carrier Frequency IR detector module.
Buy It Now
$5.45 Shipping Condition: New Location: Villa Park, United States You can start with various electronic projects by using the Arduino software (IDE). It has everything that Arduino/Genuino UNO has, even with more analog ... moreinput pins and onboard +5V AREF jumper. This board has 22 digital inputs and outputs, and 8 analog inputs - a module with many interfaces.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Supports 14443A compatible transponder signals. In addition, it supports the fast CRYPTO1 encryption algorithm and verifies the MIFARE series of products. ... more[Introduction to RC522 chip]. The MF522-MINI module uses the RC522 original chip to design the card reader circuit.
Buy It Now
Free Shipping Condition: New Location: United States Supporting WT588D VoiceChip PC software, the interface is simple, easy to use. The play can greatly limit the functionality WT588D voice chip;. USB download ... moremode, support for online download / offline download; WT588D voice chip, even in the case of electricity, will also be able to download the data to the normal SPI-Flash;.
Buy It Now
$5.35 Shipping Condition: New Location: Villa Park, United States ESP-01S ESP8266 Serial Module. Wireless standard:802.11b/g/n. Wireless network mode: station/softAP/SoftAP+station. Safety mode: WPA/WPA2. A-MPDU & A-MSDU ... moreaggregation & 0.4ms guard interval. Integrated TCP/IP protocol stack.
Buy It Now
Free Shipping Condition: New Location: Prescott, United States This is a communication adapter designed to allow communication over USB to devices with RS485 serial interfaces. This communication adapter is compatible ... morewith Windows XP/7/(10?). NOTE: You may need to install drivers (available online) for this device to function with your computer.
Buy It Now
$3.11 Shipping Condition: New Location: China Are the I / O pins exhausted?. On board 3.3V level converter circuit, if you don't solder pad of VCC-VDD, the PCF8575 level is 3.3V. Open drain interrupt ... moreoutput pin for input change interruption. Quantity: 1 PC.
Buy It Now
$2.99 Shipping Condition: New Location: China Support MP3 and WAV decoding formats.
Buy It Now
$5.45 Shipping Condition: New Location: Addison, United States Working frequency: 315MHz. Transmission power: 25mW (315MHz at 12V). Bandwidth: 2MHz (315MHz, having result from testing at lowing the sensitivity 3dBm). ... moreThis product is DIY kit, NOT the end product!
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
$15.00 Shipping Condition: New Location: Woodland, United States (Note:This kit does NOT include batteries, users need to prepare 2Pcs 18650 batteries. ). KEYESTUDIO Robot -This product is suitable for users over 12 ... moreyears old with a theoretical basis for electronic programming.By assembling this robotic arm, it can help beginners have a deeper understanding of programming and electronics.
Buy It Now
Free Shipping Condition: New Location: United States Note:It's HC-06 Bluetooth module. Compatible with bluetooth master module"、slave module"or master-slave(whole) module. Allows your device to both send ... moreor receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
|
|
|
|
SEEED STUDIO Relay Shield Arduino 35VDC 70W 315/433MHz RF Module Interface
Use this module with an Arduino. Or add an xbee RF module to make your own robot!
|
|
|
Sieko L4044 STN ARDUINO LCD Display Module 5v 40 Char. 4 Lines
Sieko L4044 STN LCD Display Module 5v 40 Char. 4 Lines Please review all pictures before bidding. Shipping to greater 48 only. Images hosted by:
|
|
|
TELAIRE T6004 NDIR CO2 SENSOR controller MONITOR MODULE Carbon Dioxide ARDUINO
FROM A NEVER STARTED PROJECT OF MINE. Telaire has joined other GE high-technology sensing businesses under a new name–GE Industrial Sensing. This is a small. Compact CO2 Module Designed to Integrate Into Existing Controls and Equipment Features: An affordable gas sensing solution for OEMs. A reliable sensor design based on 15 years of engineering and manufacturing expertise. Flexible CO2 sensor platform designed to interact with other microprocessor devices. Eliminates the need for calibration in most applications with Telaire’s patented ABC Logic™ software. All units are factory calibrated and can be configured to measure CO2 concentration levels up to 5% By joining GE Sensing. Telaire® can now offer high-volume manufacturing capabilities, a global sales force, and additional engineering resources to support your sensing application ... moreneeds. Method: Non Dispersive Infrared(NDIR) Gold plated optics,b diffusion or flow through sampling(with Telaire’s Patented ABC Logic Self Calibrated Algorithm) Measurement Range configurable as 0 to 2000 ppm or 0 ton 5.000 ppm Dimensions 2 x 2.25 x 0.75 in(50.8 x 57.15 x 19.04 mm) Accuracy@ 72°F(22°C) when compared against a certified factory reference ± 40 ppm + 3% of reading Temperature Dependence 0.2% FS per °C Stability Non Linearity Pressure Dependence 0.135 of reading per mm Hg Calibration Interval Not required Response Time Signal update Every 2 seconds Warm up time Operating conditions• 32°F to 122°F(0°C to 50°C) 0 to 95% RH, non condensing Storage conditions-40°F to 158°F(40°C to 70°C) Outputs: Digital SPI/Microwire or UART@ 9600 Baud Analog 0 to 4 VDC Power Supply Requirements 5 VDC regulated(± 5% Power Consumption• 0.75 watts peak• 0.15 watts average Interface Connections Designed for 12 pin male header with 0.1 in(2.54 mm) Spacing. Flow Rates(via flow ports) Diffusion version 80– 120 cc/min Flow through version 40– 50 cc/min* Handling and OEM assembly may affect factory calibration. Specified accuracy
|
|
|
Digi International Xbee Pro S1 Arduino wireless Module 60mW XBP24-AWI
Digi International Xbee Pro Series 1 for arduino. 60mW output. XBP24-AWI can be found on Sparkfun website. Let me know if you have any questions. Thanks for looking.
|
|
|
Fastrax UP501 GPS Module, with components and breadboard. Ideal Arduino Robotics
Hi Folks, Here we have a Fastrax UP501 GPS Module. On a breadboard with the components you need to get it working. You can find an article about it at: http:www.babelduck.com/fastrax-up501-gps-module/ You can also find out more about interfacing it with an Arduino by just searching Google for'UP501 Arduino' Features: Low power consumption: 75mW@ 3.0V, Configurable fix rate. Up to 10Hz, Ultra High Sensitivity: 148dBm(Cold Start Acquisition) 165 dBm(Navigation) Tiny form factor– 22mm x 22mm x 8mm, Embedded patch antenna 18.4 x 18.4 x 4.2 mm, NMEA protocols(default speed: 9600bps) One serial port(default: CMOS level) 1PPS output, A-GPS with 14-day extended ephemeris, WAAS/EGNOS support, MediaTek MT3329. 66-channel receiver, Works with ArduPilot: http:code.google.com/p/ardupilot/ Easy to interface with Arduino. PIC& Raspberry Pi, ... moreGreat for UAVs. Helicopters& Quad rotors Embedded GPS antenna, Low power consumption, Ultra High Sensitivity of-165dBm, Configurable fix update rate up to 10Hz, I will do combined shipping if you are buying more than one lot from me. I've decide to sell of all my electronics and start from scratch: So keep an eye out for my other auctions. If you have any questions please do not hesitate to contact me. All the best. Richard.
|
|
|
Arduino WiFi Module - Header Pin Connection - ADRUINO - PIC - Pi - Wireless
Here we have a mini WiFi module that could be suitable for Arduino ect. use. Its connection is via a 8 pin header. Please take a moment to read All items are salvaged from working equipment. I tear down hi end test and medical equipment. Definition as tested in my listings: Individual components are pulled from working equipment and are tested. Boards, displays and IC's are fully working before removal. Static sensitive devices are pulled using the correct equipment and stored correctly. Items do not come with data sheets or any other information although I will try list most component ID's. Most items may require you to be a little creative to allow integration into your project but that's the fun of it all. Everything posted has tracking and requires a signature for your peace of mind. Postage is always combined so if you win ... moremore than one item please wait for an invoice. Overseas bidders are welcome but please ask for a quote before the item ends. Not after. Overseas items will require insurance and tracking, NO exceptions. Finally everything is posted quickly. Usually the next working day. Feedback is left once received, Good luck and happy bidding. IF YOU DON'T PAY WITHIN 3 DAYS I WILL OPEN A NON PAYING BIDDER CASE SORRY NO ZERO RATED BIDDERS. I KNOW WE ALL NEED TO START SOMEWHERE BUT I'M HAVING TOO MUCH HASSLE WITH NON PAYING ZERO RATED BIDDERS.
|
|
|
Arduino Ethernet Shield + PoE 802.11af module
The Arduino Ethernet Shield with PoE(power-over-Ethernet) Module allows an Arduino board to connect to the internet. It is based on the ethernet chip( The Wiznet W5100 provides a network(IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top. The R3 version brings to this shield the 1.0 standard pinout that consist in 4 additional pins: 2 of them placed near the AREF pin. That are used for TWI communication, and the other 2 are placed near the RESET pin. The IOREF pin is used to adapt the shield to the board on which is mounted. The last one ... moreis not connected and is reserved for future uses. The latest revision of the shield adds a micro-SD card slot. Which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega(using the Ethernet library) It also have a separate power-over-Ethernet(PoE) module that is soldered to the board to provide power from a conventional twisted pair Category 5 Ethernet cable. It is IEEE802.3af compliant, and works with all compliant PoE injectors currently available.
|
|
|
5 Pcs 84*48 Nokia 5110 LCD Module Black on Blue backlight For Arduino 84X48
NY PLATFORM products MAINLY INCLUDE Regulated DC Power Supply. Switching Power supply, Power Inverter, Soldering/Rework Station, SMD Hot air rework station, SMD Antistatic Lead free soldering station& Accessories, Digital Storage Oscilloscopes, Testing meters and instruments& Accessories, Power Tool Battery& Accessory etc. NY PLATFORM SUPPLIES HIGH-quality products. PROVIDES specialty technical support and DELIVERS SERVICE GUARANTEES TO ENSURE CUSTOMER SATISFACTION. WITH THESE competitive advantages, WE NOT ONLY continue to broaden product CATEGORIES to LEAD in highly competitive marketS, BUT ALSO SUCCEED to STRENGTHEN OUR PARTNERSHIPS WITH VARIOUS CHANNELS IN emerging marketS. AS ALWAYS, We strive to OFFER our customers THE BEST integrated solutionS and BEST-IN-CLASS service. 84 X 48 DOTS LCD Display Module. These displays were ... moreused in old Nokia 5110/3310 cell phones. It is a 84x48 pixel monochrome LCD display. These displays are small. But very readable and come with backlight. This display is made of 84x48 individual pixels, so you can use it for graphics, text or bitmaps. These displays are inexpensive, easy to use, require only a few digital I/O pins and are fairly low power as well. THERE ARE SOME SCRATCHES ON THE METAL SHELL EVEN ON THE SCREEN LIKE THE PHOTO SHOWING. It's compatible with Nokia 3310. The code is the same for Nokia 3310 and 5110, so there is the ready-made arduino library for this LCD. Nokia 5110 LCD is a 84*48 pixels matrix LCD. Black text on Blue background. Nokia 5110 LCD is low-cost. Monochrome LCD with 84x48 display. It is popular for 8-bit AVR/PIC projects, search google for'Nokia 5510 LCD' and you will find lots of resources. Note:The Blue backlight LCM's pin compare with White backligt LCM's on the opposite. 84 X 48 DOTS LCD Display Module x5, To international buyer: Please note. We do fast shipping in one business day but sometimes the USPS international shipping take 25-30 days to finish the delivery as the package MAY BE INSPECTED BY BOTH CUSTOMS, s
|
|
|
5pcs DC 5V Stepper Motor + ULN2003 Driver Test Module Board 28BYJ-48 for Arduino
Store Category Description Motor Features: Rated Voltage: DC5V 4-phase Step angle: 5.625 x 1/64 DC Resistance: 200Ω±7% 25C) Insulation Resistance: 10MΩ(500V) Dielectric Strength: 600V AC/ 1mA/ 1s Insulation Grade: A No-load Pull in Frequency: 600Hz No-load Pull out Frequency: 1000Hz Pull in Torque: 34.3mN.m(120Hz) Detent Torque: 34.3mN.m Temperature Rise: Noise: Cable length:23.5CM ULN2003 Driver Board: A. B, C, D four-phase LED indicates the status of the stepper motor work. Stepper motor with a standard interface. When used directly pluggable. Drive Module Board Size:2.8cm x 2.8cm x 2cm. Package included 5pcs stepper motor 5pcs ULN2003 Driver board Hotsale Payment We accept payment via Paypal. Shipping Shipping to USA 11- 20 days, Refund time:25 days Shipping to Europe 15- 30 days, Refund time:35 days Shipping to Canada.Australia 15- ... more30 days, Refund time:35 days Shipping to Italy.Brazil,Israel 25- 40 days, Refund time:45 days Shipping to other countries 20- 30 days, Refund time:35 days About tracking number. Cause we sell the items at low price.So if you buy items less than 20usd,we have no tracking number,otherwise,if you buy items more than 20usd,we will send them with a free tracking number. If package not received.What you should do? We list all shipping time to the worldwide as above.Cause we are from china,it is international shipping,so packages take much time to arriveIf you don't receive the package in the time as we write,please contact us before you leave negative feedback and open the case.We are honest and professional seller,we will contact the post office in time after you contact us, if we confirm that the package are lost during the shipping,we will refund your full payment or send you another package at once.Hope your understanding and cooperation. Copyright © 2013 goldpart. All rights reserved
|
|
|
RFID Reader Module ID-12 Arduino Uno & Mega Compatible
Selling a ID-12 RFID Reader Module. Model No. ID-12 DESCRIPTION: This item is being sold as a completed board with mounting holes. All the components necessary for operation have been combined onto one PCB. You can either desolder the ID-12 module or find a matching connector for the board. I'm selling this board for the same price as just the ID-12 module. ADDITIONAL INFO: This is a very simple to use RFID reader module from ID Innovation.With a built in antenna. Power the module, hold up a card, and get a serial string output containing the unique ID of the card. 5V supply 125kHz read frequency EM4001 64-bit RFID tag compatible 9600bps TTL and RS232 output Magnetic stripe emulation output 100mm read range Will ship within 24 hours of receiving payment.
|
|
|
PCI PCIM 201 DOT MATRIX 2X16 LCD DYSPLAY MODULE HIGH CONTRAST 13 PINS ARDUINO
UP FOR SALE: Used-ORIGINAL-OBTAINED FROM GOVERNMENT SPARE SURPLUS(LANL) Note: This display never been used. Or mounted, selling used only just for minimal cosmetic ware. Display Was test it and working. Please look at the pictures May be good to interface with Arduino Controller PC-I PCIM 201 DOT MATRIX 2X16 LCD DYSPLAY MODULE HIGH CONTRAST 13 PINS ARDUINO PAYPAL FOR PAYMENT 30 DAYS RETURN BUY WITH CONFIDENCE $1.84 SHIPPING USPS BOXED PACKAGE TO THE CONTINENTAL US ONLY EMAIL FOR ANY QUESTION THANK YOU
|
|
|
Dual-H Bridge L293D 4 DC motor driver module for Arduino robot 4WD smart car BE
Dual-H Bridge L293D 4 DC motor driver module for Arduino robot 4WD smart car SKU: A1008 Item Description Features: Adopts L293D chip it can drive 4 DC motors 4 Channel Stepper motor port Max Current:1 A Driver: L293D Dual H Bridge DC Motor Driver IC Driven part of the input voltage Vs: +5 ~ 16V(or +7-35V depending on power supply needs) The logical part of the work current is: 0- 36mA Drive part of the operating current Io: 2A Maximum power dissipation: 20W(T = 75 degree Celsius) Control signal input level(IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8) High level: 2.3V ≤ Vin ≤ Vss Low:0.3V ≤ Vin ≤ 1.5V Operating temperature: 25 C ~ +130 C Drive Type: Dual high-power H-bridge driver Size: 90mm × 37mm Package Includes 1x L293D Drive module Note: We will repackage this item to reduce shipping weight paper and bag waste. We guaranty the item will be well ... moretreated and protected. Let's protect the environment together! Payment Policy We only accept payment through Paypal. Which is the most convenient and popular way for Ebay transaction. Shipping Policy We Ship to Worldwide. Except Italy. Nigeria, Hong Kong, and we do not ship to APO/FPO Items will be shipped within 1 business day on payment received. Items are shipped using Airmail. Which reach most of the countries within 10 to 25 business days. Delivery time depends on destination and other factors. It may takes up to 25 business days. Country Delivery Time Working days 5-10 11-15 16-20 21-25 26-30 31 Calendar days 5-12 13-19 20-28 29-35 36-45 41 United States Rate of arrival 9% 50% 35% 5% 1% Resend or refund Canada. Australia Rate of arrival 4% 45% 43% 6% 2% Resend or refund United Kingdom Rate of arrival 7% 46% 44% 2% 1% Resend or refund Europe(Exclude UK) Rate of arrival 2% 38% 45% 11% 4% Resend or refund Others Rate of arrival 3% 38% 48% 8% 3 Resend or refund Guarantee Policy 12 months Warranty. Buy with confidence! Return Policy If you are not satisfied when you receive your item. Please return it within 14 days for a replacement or money back. Please contact me befo
|
|
|
"ARDUINO" SPARKFUN INVENTOR'S KIT free relay module, RGB cathode, and sensor..
very good offer used 3X only. With free relay module
|
|
|
IMS-1(50A Single-channel H-Bridge Motor Driver Module, Arduino,Intelligent Car)
50A Single H Bridge Motor Driver Module PID for Arduino Intelligent Car Description: 50A Single H Bridge Motor Driver Module PID for Arduino Intelligent Car Descriptions: Designed for Arduino intelligent car. The whole bridge DC brush motor drive,for hollow cup motor is very good,PID program source send by email. This drive brake quickly. And easy to operation. The customers evaluation that its better than the MC33886 etc. The driver use the whole bridge drive chip + extremely low impedance MOSFET.make the MOSFET switching losses to lowest. Improve power utilization rate. MOSFET drive chip with hardware brake function and power feedback function. The current shock resistance MOSFET type. Resistance is 0.003 ohm, can quickly make MOSFET open channel, improve the speed of the motor curvature, also canrapid in electrical braking. This can make ... moreof car can quickly start also can quickly kill car. Drive can work at 0%98% of the PWM duty cycle. Because the drive is NMOS circuit,NMOS circuit features is not to 100% PWM, when PWM 100% of control circuit,long time carries out the operation can lead to drive damage Performance parameters: Rated voltage: 3 V-15 V- R1 short circuit. VCC and B + short circuit. VCC output voltage and drive the input voltage. R1 open circuit. VCC and B + disconnect. VCC input voltage 3-12 V. Rated current: 50 A- Current peak: 100 A- Switching frequency: 1 K to 200 kHz- Dimensions: 5.0 cm(long) 5.0 cm(wide) 3.1 cm(high) Pin Defination: V + Power Input +- GND Power Input- EN Driver Enable. High enable, low off- RPWM Forward PWM input. High active- LPWM Reverse PWM input. Active high- CT Current signal output.Analog signal- VT Voltage signal output. Analog signal Package include: 1x Driver module Shipping& Payment: Here Offer 100% Satifiation Service.Inlucde re-send item&refund payment; All items here offer 1 year warrenty It is not my Duty for Custom Tax All item(s) will be shipped via int'l register air mail or EMS. The time normally takes 7-15 busi
|
|
|
New 1pcs DIY TTP223B Arduino Digital Touch Sensor Capacitive Touch Switch Module
Product images, Description: 100% brand new and high quality The module is based on a touch-sensing IC(TTP223B) capacitive touch switch module. In the normal state. The module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Jog type: the initial state is low. High touch, do not touch is low( similar touch of a button feature) Module can be installed in such as surface plastic. Glass of non-metallic materials In addition to the thin paper( non-metallic) covering the surface of the module. As long as the correct location of the touch, you can make hidden in the walls, desktops and other parts of buttons Features: Low power consumption Power supply for 2 ~ 5.5V DC Can replace the traditional touch of a button Four M2 screws positioning ... moreholes for easy installation Specification: Item Min Typical Max Unit Power supply voltage VCC 2.0 3 5.5 V Output high VOH- 0.8VCC- V Output low VOL- 0.3VCC V Output Pin Sink Current( VCC = 3V. VOL = 0.6V) 8- mA Output pin pull-up current( VCC = 3V. VOH = 2.4V) 4- mA Response time(low power mode) 220 mS Response time(touch mode) 60 mS Size 24x24x7.2 mm Touch Sensor Interface:the last picture show) Control Interface: A total of three pins(GND. VCC, SIG) GND to ground, VCC is the power supply, SIG digital signal output pin; Power Indicator: Green LED. Power on the right that is shiny; Touch area: Similar to a fingerprint icon inside the area. You can touch the trigger finger. Positioning holes: 4 M2 screws positioning hole diameter is 2.2mm. The positioning of the module is easy to install, to achieve inter- module combination; Package: Touch Sensor x 1 Shipping, Item will be shipped within 24-48 hours after full payment is received. We ship worldwide with flat rate shipping by Hong Kong Air mail. this international order may take longer to arrive.Normally the shippment to worldwide is used to take 15 to 25 busines
|
|
|
Wago 787-912 24V 2A DC Power Supply Module Arduino Raspberry Pi LOK4601-2RC1
Please Read Carefully! This Wago 787-912 24V 2A DC Power Supply Module Arduino Raspberry Pi LOK4601-2RC1 is in fair physical condition with a few light scratches from previous use. Please see pictures for more detail and feel free to make us an offer. Sunnking ships exclusively with UPS and due to company policy we do not ship on other UPS accounts. We do not ship with any other carriers. Nor do we alter our shipping methods for any reason. International Bidders Please Note Shipping outside of the United States is expensive with UPS(our exclusive carrier) We do not use USPS under any circumstances. International bidders please be aware that UPS charges COD brokerage fees as well as import taxes and possible other fees based on the final value of the eBay item being imported. Charges vary from country to country and sometimes province to province. ... moreSo we are unable to estimate these fees ahead of time. These charges are the buyer’s responsibility and are not covered under the stated shipping/handling charge. Please contact UPS for more information about brokerage fees. Please Read Carefully! Hours of Operation: We are open Monday through Friday. 8:00am to 4:30pm EST. Payment: We must receive payment within 7 days of auction close. If we have not received your payment by the 6th day you will receive a final e-mail requesting payment. Payment Options: PayPal Only. Credit Cards: Buyers must process credit card payments through PayPal. Local Pickups: There is a $10.00 fee per local pickup appointment. All Sunnking local pickups require two(2) business days notice. Schedule A Local Pickup. Parts Removal: The item(s) shown above will not be dismantled or separated. NY Residents: Responsible for(8% for NY Sales Tax. ALL ITEMS ARE GUARANTEED TO BE"AS DESCRIBED" Return Process: Please complete our online RMA Form and be sure to fill out all fields(note: requests that do not contain all of the necessary information will not be processed) Please be aware that buyers are responsible for return shipping charges r
|
|
|
Matrix Orbital LK162-12-WB LCD DISPLAY MODULE; Arduino; LCDi2c Library
Matrix Orbital LK162-12-WB LCD DISPLAY MODULE 16 characters by 2 lines display Returnable if DOA(shipping is non-refundable) Product page: Display Appearance Character X Lines, Width x Height, 16 x 2 Module Size Width(mm) x Height(mm) x Thickness(mm) 80.00 x 36.00 x 28.82 Display Size Width(mm) x Height(mm) 64.50 x 15.50 Active Area, Width(mm) x Height(mm) 56.20 x 11.50 Character Size, Width x Height, 2.95 x 5.55 Character Pitch, Width x Height, 3.55 x 5.95 Pixel Size, Width x Height, 0.55 x 0.65 Pixel Pitch, Width x Height, 0.60 x 0.70 Text Color Red Background Color Black Features Interface Options, RS232TTL RS232 Keypad 12 Dallas One Wire N/A GPO 7 Buffer, 128 bytes, Environmental Conditions Operating Temp Min to Max, 0.00 o c to 50.00 o c Storage Temp, Min to Max, 20.00 o c to 70.00 o c Operating Temp(E) Min to Max, 20 o c to +70 o c ... moreStorage Temp(E) Min to Max, 30.00 o c to 80.00 o c Max Humidity 90% Power Requirements Supply Current 40 mA, Backlight Current 90 mA, Appears to be supported with ARDUINO/ LCDi2c Library: LCDi2c Library This is the home of the i2c character based LCD libraries Background: After looking at the display choices I decided I wanted to use a display that ran on the i2c buss. This takes up only two pins and is very fast. As there was no current library I decided to write one. And in turn am making it available to the Arduino community. API Compliance: I have also put together a recommended API for use when developing libraries for character based LCD displays. The character based documentation can be found here. Info on using with the library can be found here. Connecting your display Not done yet! Currently Supported displays: Display Compliant Library Connection F E, i2c, F E, i2c, F E, i2c, F E, i2c, F E, i2c, F E, i2c, F = Fully Supported P = Partially Supported D = Being Developed E = Extended Library Support Click on the library name to download the latest version of the library for your display Notes: The libraries as installed include the extended functions of e
|
|
|
Hyundai HG2450-4 LCD Display Module - TOSHIBA T6963C - Arduino - PIC - PI
Here we have a nice display module made by Hyundai. The display uses the Toshiba T6963C: http:forum.arduino.cc/index.php?topic=22624.0 This is a great board as there is room under the display to mount your project. Supplied in mint condition. Static bagged. I post my items quickly. The same day if possible if not the next working day. All items posted have tracking and this number is uploaded to PayPal. If applicable ESD precautions are observed and boards ect are pulled and stored correctly. If you buy more than one item that has free postage I will refund you the postage difference. Buy it now offers are accepted so please ask. Any and all questions please ask. Thank you for reading and happy ebaying. RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bfg2%3E-146e3cc28c3-0x10d-
|
|
|
Arduino and raspberry pi 5V and 3v 22 channels Logic Level Conversion Module
Overview: 1. Arduino Interface 22 channels Logic level conversion module 2. 3.3v convert to 5v or 5V convert to 3.3v 2. No Extra control PIN are needed. 3. 3.3v Aruino Interface convert to 5V Arduino Interface or 5V Arduino Interface convert to 3.3v Arduino Interface 4. SPI I2C UART GPIO. 3.3v to 5v or 5V to 3.3v Logic level conversion Support Interface: The Surface with 3.3v indicate that the interface is ready for 3.3v input or output The Surface with 5v indicate that the interface is ready for 5v input or output sketch map: Connect to Arduino UNO R3. 5V Arduino Interface convert to 3.3v Arduino Interface Connect to Raspberry Pi though ARPI500 expansion Board.Pi Interface convert to 5v Arduino Raspberry Pi communicates with Arduino UNO R3 though ARPI500 expasion Board and 22 channels Logic level conversion module Package Contains: 1.22-LOGIC ... morex 1 Shipping& Handling Policy· Generally. It always take 7-25 business days to ship to USA, United Kingdom, Australia,Canada,France and most other countries. And we always will ship our customers' parcel in seven business days.After we receive payment. If you haven’t received the item after 25 working days. Please contact us. We'll investigate and solve the problem together. International Buyers Note: Import duties. Taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. if your country have very strick policy on tax and meanwhile you don't want to pay the tax. Please tell us what's the value should we indicate on the parcel and we will mark the value as you required. We ship to worldwide. So if your country or place is very far away, please allow your parcel more time to arrive and we supply two kinds of shipping way: 1. C hina Post flat air mail(this way is default shipping way for free shipping mode) 2. Express Delivery Shipping Way: This shipping way contain DHL.UPS,Fedex, if you need our products urgently, please use this shipping way and you can contact us and ask us the to fi
|
|
|
LCD Display Module - Display area 50 x 40 mm - Header Pinned - Arduino - PIC
Here we have a nice LCD graphical display module. The display area measures 50 x 40 mm. The board measures 90 x 60 mm. This has an Hitachi Chipset with Sony ram. Header pinned ready to use. I post my items quickly. The same day if possible if not the next working day. All items posted have tracking and this number is uploaded to PayPal. If applicable ESD precautions are observed and boards ect are pulled and stored correctly. If you buy more than one item that has free postage I will refund you the postage difference. Buy it now offers are accepted so please ask. Any and all questions please ask. Thank you for reading and happy ebaying. Any and all questions please ask.
|
|
|
Arduino TinkerKit 16x2 Text Display LCD Module Shield T110061
Browse our Store. Sports& Outdoors Video Games Home& Garden Health& Beauty Clothing. Shoes& Accessories Electronics Musical Instruments/Gear Cameras& Photo Customer Service. Today's Hot Deals Arduino TinkerKit 16x2 Text Display LCD Module Shield T110061(64173) P1878172) PACKAGE CONDITION: Opened manufacturer's packaging FUNCTIONAL CONDITION: 100% Fully Functional COSMETIC CONDITION: Looks lightly used ITEMS INCLUDED: TinkerKit 16x2 Text LCD Shield ITEMS KNOWN TO BE MISSING: PLEASE SEE PHOTOS FOR WHAT IS INCLUDED. Please do NOT ASSUME an item is included if it is not in the photo. SPECIFICATIONS: With the TKLCD module you can write text on the module's screen in a few minutes. It has an LCD display on board and it requires a dedicated software library that is available on. COLOR: With the TKLCD module you can ... morewrite text on the module's screen in a few minutes. It has an LCD display on board and it requires a dedicated software library that is available on. Arkansas Buyers must pay a 6% Sales Tax. Click an Image to Enlarge Some images may be stock photos. Please read ITEM DESCRIPTION. ABOUT US bigdealonthehill has partnered with some of the Nation's largest retailers and distributors to aggressively liquidate consumer merchandise. This merchandise is generally customer returns. Overstock items, refurbished or even brand new unused retail shelf pulls. Please note: If the item is a known refurbished item, it will be stated in the listing as well as any other condition known. Also, we do offer BRAND NEW merchandise on some of our other listings. Please see auction condition for details. WHY BUY FROM US? WE WORK FOR YOU. ALL merchandise is tested prior to listing unless it is sealed in the factory package. This will include powering on the unit and checking all the major functions. You will find condition and testing notes in the item description. This helps our buyers know EXACTLY what they are getting. WE EARN YOUR BUSINESS. We have worked with thousands of ebay members to achi
|
|
|
MMA7361 Accelerometer Sensor Module for Arduino Raspberry Pi - US Seller
Hello, This was a test unit that was wired up just one day for testing. It's technically"used. but only for a few hours. I'm in Pensacola, Florida, so you won't need to wait for one month like I did to receive it from China. I'll ship same day for payment received by 4pm by USPS First Class mail. These are very inexpensive when ordered from China, but waiting forever for it to get here is a pain. This sells new from SparkFun for $12+shipping(~$6) so I'll go $10 with free shipping. I offer a 14-day return policy if you pay the return shipping. Thanks- DESCRIPTION 1. On-board MMA7361(replaces MMA7260) Low cost, micro-capacitive acceleration sensor. 2. Support 5V/3.3V voltage input. On-board RT9161, has much lower pressure drop and much faster load corresponding speed than 1117. Very suitable for high noise power environment. ... more3. Range is chosen by MCU IO or resistance. 4. Common pins have been drawn forth. Inserted pins are standard 100mil(2.54mm) convenient for dot matrix board. 5. Dormancy enable can be controlled by MCU IO. 6. PCB board is gold-plated both sides. Size: 27.9mm x 16.8mm.
|
|
|
Sainsmart 3.2" TFT LCD Display Module with SD slot for Arduino AS IS READ
This was new and unused when I noticed through the packaging that the screen was cracked. I opened it to check it out and it looks like only the glass panel is cracked. NOT the LCD.
|
|
|
Ublox GY-NEO6MV2 Flight Controller GPS Module For Arduino EEPROM MWC APM 2.5
Ublox GY-NEO6MV2 Flight Controller GPS Module For Arduino EEPROM MWC APM 2.5 Description: Ublox GY-NEO6MV2 Flight Controller GPS Module For Arduino EEPROM MWC APM 2.5 Features: Power: 3V-5V- Built-in ceramic antenna ensures strong signal- With data backup battery- With power-down data storing EEPROM- Antenna size: 12* 12mm Package includes: 1* Ublox NEO-6M GPS Module Shipping& Payment: Here Offer 100% Satifiation Service.Inlucde re-send item&refund payment; All items here offer 1 year warranty It is not my Duty for Custom Tax All items will be shipped via int'l air mail( no tracking number for items under $65) The time normally takes 7-15 business days. may be later arrivel if the item is checked by custom; We only accept paypal payment.
|
|
|
1PCS New V03 Module Wireless Control For Arduino ZigBee XBee Blue
This shield V03 can achieve a simple two crunodal ZigBee network，achieve wireless communication between Arduino， and allows the Arduino to wireless communicate over a modified ZigBee protocol using the popular XBee module. It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5. Standard and Pro versions. Package: 1 x v3 module. Item will be shipped within 24 hours after full payment is received. Normally the shippment to worldwide is used to take 20 to 25 business days. Exclude Sat& Sun, We accept PayPal only. Payment must be received in 7 business days of auction closing. Please leave note for your special request(e.g. Colors or Size) in ebay note when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be ... moreprocessed instantly and same day dispatched. If you have any questions. Please feel free to email our servicer，and we will reply you ASAP. If no response within 24 Hours, please check the spam of mail box or kindly re-send it to us. We greatly appreciate your POSITIVE feedback. Please do NOT leave negative or neutral feedback without any contact. If you haven't received item in 45 days. Please contact us and we will arrange refund or resend,
|
|
|
XBEE PRO Series 2 Module with Wire Antenna AND Breakout AND Arduino Shield!
I used this part once. But no longer need it. The Arduino Shield makes it easy to prototype. And the breakout board makes it easy to interface with a breadboard directly. This is the XBee XBP24-BZ7WIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers. Computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules. They are not compatible with the outdated Series 2.5 Modules. Note: If you are looking for a simple ... morepoint-to-point configuration. You might want to try the Series 1 instead. The Series 2 requires considerable setup and configuration. We highly recommend Building Wireless Sensor Networks as a guide for setting up mesh networks. Note: Series 1 and Series 2B XBee modules have the same pin-out. However. Series 1 modules cannot communicate with Series 2B modules. Note: If you are using these outside of the United States. Please check with your local laws regarding radio communication. Features: 3.3V@ 295mA, 250kbps Max data rate, 50mW output(+17dBm) 1 mile(1600m) range, Wire Antenna, Fully FCC certified, 6 10-bit ADC input pins, 8 digital IO pins, 128-bit encryption, Local or over-air configuration, AT or API command set, Documents:
|
|
|
Arduino Uno,GSM Shield,xbee Wifi Module And Programmer And sensor Shield/xbee
This auction is for a arduino uno a sim900 gsm shield with 2 antenee a xbee wifi module with the USB programmer and a xbee compatible sensor shield
|
|
|
New HC-06 Wireless Bluetooth Transeiver RF Module line for Raspberry Arduino
Condition;New. Package: 1 x HC-06 Module. Note: All communications are handled through Email. We strive to answer all emails as quickly as possible. But due to high email volume and different time zones,it may take times for us to reply(and we can not reply emails on Weekends and other public holidays, please wait with patience if you send us emails on/before these days) Thanks in advance for your patience. Shipping Item will be shipped within 24-48 hours after full payment is received. The Item will be shipped by air mail，Normally the shippment to worldwide is used to take 20 to 25 business days. Exclude Sat& Sun. Payment We only accept payment through Paypal. Payment must be received in 7 business days of auction closing. Any special request cannot be accepted after 24 hours of payment. Because most of orders will be processed instantly ... moreand same day dispatched. Warranty&Feedback If the item is defect when you receive it or you are not satisfied with it. Please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 3 months. You can return it to us. We will send you a new replacement after receiving the defective item. Contact Us We care about our valued buyers. If you have any questions, our Customer Service staffs will be very glad to help you. We try our best to reply your email as soon as possible, please kindly allow 24 hours(working day) for us to response. Thank you. We greatly appreciate your POSITIVE feedback. Please do NOT leave negative or neutral feedback without any contact.
|
|
|
HC-06 Wireless Bluetooth Transeiver Module Serial+4p for Raspberry pi Arduino
Product images, Description: Condition;New. Package: 1 x HC-06 Module. Shipping, Item will be shipped within 24-48 hours after full payment is received. We ship worldwide with flat rate shipping by Hong Kong Air mail. this international order may take longer to arrive.Normally the shippment to worldwide is used to take 15 to 25 business days, exclude Sat& Sun. Payment, We accept PayPal only. Payment must be received in 7 business days of auction closing. Please leave note for your special request(e.g. Colors or Size) in ebay note when you pay the order. Any special request cannot be accepted after 24 hours of payment. Because most of orders will be processed instantly and same day dispatched. Warranty, If the item is defect when you receive it or you are not satisfied with it. Please return it within 14 days for a replacement or money ... moreback. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 3 months. You can return it to us. We will send you a new replacement after receiving the defective item. Contact Us, If you have any questions. Please feel free to email our service specialists 24 Hours a Day, 7 Days a Week, and we will reply you ASAP. If no response within 24 Hours, please check the spam of mail box or kindly re-send it to us. We greatly appreciate your POSITIVE feedback. Please do NOT leave negative or neutral feedback without any contact. If you haven't received item in 30 days. Please contact us and we will arrange refund. On 08-Oct-14 at 04:32:16 EDT. Seller added the following information:
|
|
|
Arduino Arduino Uno Ultimate Starter Kit + LCD Module -- Used
All original parts are still in the box and it works like new. I'm including three spools of wire(that didn't originally come with the kit)
|
|
|
LCD Touch Module Resistive Arduino Raspberry PI
LCD touch module arduino raspberry Pi. Salvaged from an old printer.
|
|
|
Lot of 2 Linx RF Wireless Module 433Mhz For Arduino
These items came from a lot which had development boards. Arduinos, and lots of robotics. Theses unit are untested. The items are used and are being sold as-is. Shipping is to the lower 48 United States only.
|
|
|
LCD Display Module with backlight for Arduino or other DIY projects
Good Display. There is stuff on the display in the photo. Display doesn't have any scratches.
|
|
|
DS18B20 Temperature Sensor Measurement Module Board For Arduino
DS18B20 Temperature Sensor Measurement Module Board For Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Board DS18B20 chip left 3P hole seat easily accessible DS18B20 chip. Pin chip has all the leads. Built-in pull-up resistor. Onboard power indicator. Main Color, Blue. Black, Brand, Assisi, Net Weight, 2g, Country of Manufacture, CHINA, Package Content, 1 x DS18B20 Module Board, Model, DS18B20, Material, Electronic Parts, Size, 21 x 10mm(L*W) Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will ... morebe prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you would like to return your product(s) for repair/ replacement/ refund. Please kindly contact our customer service representatives via email for an authorized? RMA number. Your returned product(s) will not be processed without a completed RMA. Buyers are responsible for the returning shipping costs under any circumstances. The photos are just for illustration purposes only. No sales tax is required. If. For any reason you are not satis
|
|
|
L7805+L7905 5V Output Dual Power Supply Voltage Regulator Module for Arduino
L7805+L7905 5V Output Dual Power Supply Voltage Regulator Module for Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Description: L7805+L7905 Chip. 2x(6V-18V) Input. Output:5V/+5V. 1.5A Max. L7805+L7905 three-terminal voltage regulator IC. Filter Capacitor with 2200uf/50V capacitor Board output interface reserved pin beside some output port. Easy to connect. On three integrated voltage stabilizing.Install the heatsink can improve the voltage stability. Following is Only for your reference. Net Weight, 52g, Country of Manufacture, CHINA, Package Content, 1 x Dual Voltage Regulator Module, Output Voltage, DC +/5V, Output Max.Current, 1.5A, Fixing Hole Diameter, 3mm, Material, ... moreElectronic Part, Input Voltage, AC 2x(6V-18V) Total Size, 88 x 30 x 33mm/3.4" x 1.2" x 1.3"L*W*H) Chip, L7805+L7905, Fixing Hole Center Distance, 55 x 24mm/2.2" x 0.94"L*W) Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you would lik
|
|
|
3Pcs L7805 7.5V-20V to 5V Step Down Voltage Converter Module for Arduino
3Pcs L7805 7.5V-20V to 5V Step Down Voltage Converter Module for Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Description: L7805 Chip. Composed of two electrolytic capacitor filter circuit. Input is no polarity. Both AC and DC. Input:AC/DC 7.5-20V Output: 5V 1.2A L7805 three-terminal voltage regulator IC of regulated power supply circuit needs few peripheral components.On three integrated voltage stabilizing.Install the heatsink can improve the voltage stability. The Two electrolytic capacitor is in order to the input and output voltage filter. Net Weight, 43g, Country of Manufacture, CHINA, Package Content, 3Pcs x Step Down Voltage Converter Module, Output Voltage, ... more5V, Fixing Hole Diameter, 3mm, Max. Output Current, 1.2A, Material, Electronic Part, Input Voltage, AC/DC 7.5V-20V, Total Size, 50 x 21 x 23mm/2" x 0.83" x 0.91"L*W*H) Fixing Hole Center Distance, 43 x 15mm/1.7" x 0.6"L*W) Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer
|
|
|
L7812+L7912 DC 12V Output Dual Power Supply Voltage Regulator Module for Arduino
L7812+L7912 DC 12V Output Dual Power Supply Voltage Regulator Module for Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Description: L7812+L7912 Chip. AC 2x(10V-18V) Output:DC +/12V. 1.5A Max. L7812 + L7912 three-terminal voltage regulator IC. Filter Capacitor with 2200uf/50V capacitor Board output interface reserved pin beside some output port. Easy to connect. On three integrated voltage stabilizing.Install the heatsink can improve the voltage stability. Following is Only for your reference. Net Weight, 51g, Country of Manufacture, CHINA, Package Content, 1 x Dual Voltage Regulator Module, Output Voltage, DC-+12V, Output Max.Current, 1.5A, Fixing Hole Center Distanc, ... more55 x 24mm/2.2" x 0.94"L*W) Fixing Hole Diameter, 3mm, Material, Electronic Part, Input Voltage, AC 2x(10V-18V) Total Size, 88 x 30 x 33mm/3.4" x 1.2" x 1.3"L*W*H) Chip, L7812+L7912, Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you woul
|
|
|
HR911105A DC 25V Arduino AVR Interface Ethernet LAN Network Shield Module Board
HR911105A DC 25V Arduino AVR Interface Ethernet LAN Network Shield Module Board More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Descriptions: This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino OnlineIt is directly supported by Arduino official Ethernet Library, It supports up to four simultaneous socket connections use the ethernet library to write sketches which connect to the internet using the shield. Main Color, Blue. Silver Tone,Black, Brand, Assisi, Net Weight, 28g, Country of Manufacture, CHINA, Model, HR911105A, Package Content, 1 x Ethernet Shield, Power Supply, DC 25V, Material, Metal. Plastic, Electronic ... morePart, Total Size, 70 x 55 x 25mm/ 2.8" x 2.2" x 1"L*W*H) Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you would like to return your product(s) for repair/ replacement/ refund. Please kindly contact our customer service representatives via e
|
|
|
L7815+L7915 15V Output Dual Power Supply Voltage Regulator Module for Arduino
L7815+L7915 15V Output Dual Power Supply Voltage Regulator Module for Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Description: L7815+L7915 Chip. AC 2x(13V-18V) Output:+/ 15V. 1.5A Max. L7815+L7915 three-terminal voltage regulator IC. Filter Capacitor with 2200uf/50V capacitor Board output interface reserved pin beside some output port. Easy to connect. On three integrated voltage stabilizing.Install the heatsink can improve the voltage stability. Following is Only for your reference. Net Weight, 52g, Country of Manufacture, CHINA, Package Content, 1 x Dual Voltage Regulator Module, Output Max.Current, 1.5A, Output Voltage, DC +/15V, Fixing Hole Diameter, 3mm, Material, ... moreElectronic Part, Input Voltage, AC 2x(13V-18V) Total Size, 88 x 30 x 33mm/3.4" x 1.2" x 1.3"L*W*H) Chip, L7815+L7915, Fixing Hole Center Distance, 55 x 24mm/2.2" x 0.94"L*W) Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchange are permitted and must be initiated by the buyer within 30 days upon receipt. If you would lik
|
|
|
TCS230 TCS3200 Color Recognition Sensor Detector Module Board For MCU Arduino
TCS230 TCS3200 Color Recognition Sensor Detector Module Board For MCU Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Features High-Resolution Conversion of Light Intensity to Frequency Programmable Color and Full-Scale Output Frequency Communicates Directly With a Microcontroller Single-Supply Operation(2.7 V to 5.5 V) Power Down Feature Nonlinearity Error Typically 0.2% at 50 kHz Stable 200 ppm/°C Temperature Coefficient Compact size 31.6(mm)x24.4(mm) 2.54mm pitch connector pin-out This board uses the TCS230 sensor to detect the color of objects. The board outputs a 0-5V analog signal corresponding to the measured color and can be directly interfaced with a microcontroller. ... moreThe TCS230 programmable color light-to-frequency converter combines configurable silicon photodiodes and a current-to-frequency converter on single monolithic CMOS integrated circuit. The output is a square wave(50% duty cycle) with frequency directly proportional to light intensity(irradiance) The light-to-frequency converter reads an 8 x 8 array of photodiodes. Sixteen photodiodes have blue filters. 16 photodiodes have green filters, 16 photodiodes have red filters, and 16 photodiodes are clear with no filters. The four types(colors) of photodiodes are interdigitated to minimize the effect of non-uniformity of incident irradiance. All 16 photodiodes of the same color are connected in parallel and which type of photodiode the device uses during operation is pin-selectable. Pin definition Working Principle and Wiring Wiring for Arduino Main Color, Black. Silver Tone, Brand, Assisi, Net Weight, 5g, Country of Manufacture, CHINA, Package Content, 1 x TCS230 Color Recognition Sensor, Model, TCS230, Material, Electronic Parts, Size, 32 x 25 x 11mm/1.2" x 0.98" x 0.43"L*W*T) Import duties. Taxes and charges are not included in the item price or shipping ch
|
|
|
MAX6675 Module + K Type Thermocouple Sensor + 4-Pin Jumper Wire for Arduino
MAX6675 Module + K Type Thermocouple Sensor + 4-Pin Jumper Wire for Arduino More More More More More Add my Store to your Favourites and receive my email newsletters about new items and special promotions! General Interest Description Shipping& Payment Return Other Term& Attention Description: Chip: MAX6675, Working Voltage: DC 5V, Operature Current: 50mA, Temperature Measurement Range: 200C to-1300C(Predure test for 0-1023C) The Temperature Measurement Accuracy: +/1.5C, The Temperature Resolution:0.25C, The Output mode:SPI digital signal, With a Fixing hole for easy to fix and install. Storage temperature:50 to +150C, This module include 1x MAX6675 Module. 1x K type Thermocouple, 1 x 4Pin Jumper Wire, The follows are for your reference only! Working Current, 50mA, Net Weight, 16g, Thermocouple Type, K Type, Country of Manufacture, ... moreCHINA, Model, MAX6675, Package Content, 1 x MAX6675 Module, Material, Electric Parts, Thermocouple Lead Length, 51cm/20" 4-Pin Jumper Wire Length, 18cm/7" Module Size, 25 x 15 x 13mm/1" x 0.6" x 0.51"L*W*H) Working Voltage, DC 5V, Temperature Measurement Range, 200C-1300C, Import duties. Taxes and charges are not included in the item price or shipping charges. Buyers are responsible for these charges. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Note that delivery times may vary. Particularly during peak periods or inclimate weather conditions. All items will be dispatched from our warehouse in China or Hong Kong directly. Due to Custom restrictions. We do not ship lighters to US We cannot ship on weekends and we do not offer Saturday. Sunday or holiday delivery. All our items will be shipped to buyer's PayPal address. Please confirm your address on PayPal before you bid We ONLY accept Paypal. We appreciate prompt payment and look forward to your business in the future. Unpaid item will be filed without receiving payment in 7 days from listing ended. Returns for exchang
|
|
|
2pcs IR Infrared Flame Detection Sensor Module for Arduino Flame Sensor
Recommendations For You HC-SR501 Human Sensor Module Pyroelectric Infrared 650nm 6mm 5V 5mW mini Laser Dot Diode Module Head WL Red TEC1-12706 Thermoelectric Cooler Peltier 60W DS18B20 Waterproof Digital Thermal Probe Sensor 1pcs Digital Humidity& Temperature Sensor DHT11 good SHT11 SHT15 DHT22 AM2302 Temperature Humidity Sensor Visit my eBay Store: ChipWorld Product Name: NEW IR Infrared Flame Detection Sensor Module SKU: 2578*2 Parsts No. Package: Brand: Quantity: 2 Purpose: Various flame. Fire detection Module Features: 1. can detect the flame or the wavelength at 760 nm to 1100 nm range of the light source. The test flame lighters distance of 80cm, the larger the flame, the greater the distance test 2. the detection angle of 60 degrees. The flame spectrum particularly sensitive 3. sensitivity adjustable(shown in blue digital potentiometer ... moreadjustment) 4. the comparator output signal clean waveform is good. Driving ability, than 15mA 5. with a precision potentiometer adjustable sensitivity adjustment 6. Operating Voltage 3.3V-5V 7. the output in the form: DO digital switching outputs(0 and 1) and AO analog voltage output 8. a fixed bolt holes for easy installation 9. small plates PCB size: 3.2cmx1.4cm 10. using a wide voltage LM393 comparator Module for use: 1. the flame flame sensor most sensitive to ordinary light is also a reaction. Generally used as fire alarm and other purposes. 2. a small panel output interface can be directly connected with the microcontroller IO port 3. the sensor and the flame to maintain a certain distance. So as not to damage the sensor temperature of the test flame lighters distance 80cm, the larger the flame, the greater the distance test 4. small plates analog output mode and the AD conversion process. You can get higher accuracy More choices! High Recommendations! MSP430 MCU Servo Potentiometers Header For more quantity. Please contact me.My skype: ada-yu2013) The Standard shipping we provide is non-regiested mail without a tracking. We provide free shipping with tra
|
|
|
MB102 Breadboard Power Supply Module 3.3V 5V For Arduino Solderless JHXP
无标题文档 T1155A11 Specification: 1.Brand new and high quality. 2.Breadboard power supply module. Compatible with 5 V, 3.3 V Apply to MB102 breadboard 3.Input voltage: 6.5-12 V(DC) or USB power supply 4.Output voltage: 3.3V/5V can switch over 5.Maximum output current: 6.Fluctuation two road independent control. Can switch over to 0 V, 3.3 V, 5 V 7.On-board two groups of 3.3V. 5V DC output plug pin, convenient external lead use. 8.Size:5.3cm x 3.5cm Package Included: 1PCS MB102 Breadboard Power Supply Module 3.3V 5V For Arduino Solderless 1. The color difference is hard to avoid in the internet sales. Generally we will adjust the colors as the same as the items.But there might be a little color difference according to different light,different monitor. So if dear you can not accept this very little difference, be cautious before you making the ... moreorders. 2. No Instructions or tools are provided for this listing.This is NOT an easy job for someone who has no technical skills with Disassembling or Assembling Cellphones/mobile phones So only purchase this item if you know how to install it.We will not be held responsible for any damages to your cellphone/mobile phone that you may cause during the changing of replacement parts. 3. International Buyers_ Please Note: Import duties. Taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. 1. Usually. We ship via USPS regular shipping to USA, other countries will by HK-post/China post flat shipping. 2. Item will be shipped out within 1- 2business days upon your payment completed(Excluding Weekends and Public Holidays) 3. Delivery time lasts approx: A) United States: 8-22business days B) Australia. United Kingdom: 15- 25 business days. C) Spain. France, Germany, Canada: 15-30 business days. D) Other countries: not more than 35 business days. 4. Please contact us if your item had not been de
|
|
|
1Pc New Optocoupler Relay Module for Arduino 5V 1-Channel H/L Level Trigger NCYG
无标题文档 T1126031 Description: 100% brand new and high quality 1-Channel relay module. With photoelectric isolation The module can be high or low by a jumper setting trigger With power and relay action indicator The module Operating voltage 5V The module uses genuine quality relay. Normally open interfaces Maximum load: AC 250V/10A, DC 30V/10A Module interface: DC+: positive power supply(VCC)5V) DC- negative power supply(GND) IN: The control end. The driving current should be more than 4mA COM: The control of loop of earth wire Package includes: 1-Channel H/L Level Triger Optocoupler Relay Module 1. The color difference is hard to avoid in the internet sales. Generally we will adjust the colors as the same as the items.But there might be a little color difference according to different light,different monitor. So if dear you can not accept this ... morevery little difference, be cautious before you making the orders. 2. No Instructions or tools are provided for this listing.This is NOT an easy job for someone who has no technical skills with Disassembling or Assembling Cellphones/mobile phones So only purchase this item if you know how to install it.We will not be held responsible for any damages to your cellphone/mobile phone that you may cause during the changing of replacement parts. 3. International Buyers_ Please Note: Import duties. Taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. 1. Usually. We ship via USPS regular shipping to USA, other countries will by HK-post/China post flat shipping. 2. Item will be shipped out within 1- 2business days upon your payment completed(Excluding Weekends and Public Holidays) 3. Delivery time lasts approx: A) United States: 8-22business days B) Australia. United Kingdom: 15- 25 business days. C) Spain. France, Germany, Canada: 15-30 business days. D) Other countries: not more than 35
|
|
 |