Buy It Now
Condition: Used Location: Morris, United States Cherry Burrell 52 Gallon Jacketed Processor – Mixing Tank. - Lightnin Clamp On Mixer – Agitation, Model XJ-65. 65 HP. - Dish Bottom to a Center Outlet ... morewith Stainless Steel Ball Valve. - Stainless Steel Construction.
Buy It Now
Condition: Used Location: Bowling Green, United States Liquid Caustic Soda 50% - Corrosive. Sodium Hydroxide Solution. 304 Stainless Steel Vertical Tank. Tank OAH: 60", 90" w/legs. (1) Side Mounted Level Sight ... moreGlass. (2) Top SS Lifting Lugs.
Buy It Now
Condition: Used Location: Buford, United States Casters - 2 swivel casters, 2 rigid. Rarely used 80 gallon stainless steel tank. Made using 1 large, bent sheet of stainless steel and 2 end pieces to ... morecap off making this unit more durable and less likely to leak due to less welds being that the main body is 1 sheet.
Buy It Now
Condition: Used Location: Hiram, United States Martin Petersen Co. 33 Gallon Stainless Steel Jacketed Mix Tank Serial No.: MT 1266-03 Model No.: N/A -W/S.S. Flip Top Cover Manufacture Date: 2001 Discharge ... moreOutlet: Bottom Dual value discharges Total Capacity Liquid: 33 Gallon Tank Height: 62” // Tank on 14” legs Tank Interior Dimensions: 18” across x 30” deep Overall Dimensions: 67”H x 24”W Weight: Approx: 300lbs Seller Note: Unit is USED with no visible signs of wear on the tank (no dents/dings/dimples). Some of the white insulation is dented/creased but not affecting the functionality or the intended use of the unit. What you see in the pictures is what is included in sale. Unit is being sold AS-IS, WHERE-IS, AS-SHOWN. Pictures are of the actual unit being purchased. If the buyer has any questions, please feel free to ask.
Buy It Now
Condition: Used Location: Vandalia, United States 300 gallon capacity.
Buy It Now
Condition: Used Location: Edison, United States Above item has not been test run or inspected for completeness. It is being sold "as-is". Pick up from item location is free.
Buy It Now
Condition: Used Location: Morris, United States Cherry Burrell 25 Gallon Jacketed Processor – Mixing Tank. - Lightnin Clamp On Pneumatic Mixer – Agitation, Model XJA-33. - Dish Bottom to a Center Outlet ... morewith Stainless Steel Ball Valve. - Stainless Steel Construction.
Buy It Now
Condition: Used Location: Antioch, United States All Fill Auger Filler, Model B300. Semi Automatic. Cycling speeds up to 120 per minute. Fill range from milligrams to 50 lbs. Tooling driven by a 1-1/2hp, ... more3/60/230/460 volt, 1140 rpm motor. Has level detector.
Buy It Now
Condition: New Location: Santa Rosa, United States Plastic gauges up to 1/4" (.64cm).
Buy It Now
Condition: Used Location: Hammonton, United States Flat sloping bottom. Built 1993. Model 1373JOVS. Item 13933-001.
Buy It Now
Condition: Seller refurbished Location: Albion, United States Feel Free to reach out to us and discuss your plants needs. RS Automation 300 Gallon Single Tank CIP Skidded System. 1- Bank of 16 SMC Ethernet solenoids. ... moreThis unit is tested and operational and can be viewed running at our Facility in Albion NY.
Buy It Now
Condition: Used Location: Morris, United States IPEC 2-Tank Inline Blending System Skid. - IPEC Static Mixer, Inline Design. - Tank CIP Spray Balls. - Manufacturer: Integrated Process Engineers & Constructors ... moreInc., Fort Atkinson WI. - Year 2007. - Skidding and loading included.
Buy It Now
Condition: Used Location: Marcellus, United States The Guardian system recycles used coolants, reducing waste fluids by up to 90%, and eliminates concerns about wastewater haul-away liabilities. Everything ... moreyou need for centralized coolant recycling is included with the Guardian.
Buy It Now
Condition: Used Location: Carol Stream, United States 300 gallon, stainless steel liquid bulk storage bin. Has 23" OD top center manway (missing lid). Serial #: 4459. (4) 7" H legs, stackable to four high ... moreand forklift capable.
Buy It Now
Condition: Used Location: Hammonton, United States Used 360 liter stainless steel vertical tank. 32" dia x 28" straight height. Dished top and bottom heads. Internal rated 30 psi/ Full vacuum@ ... more300 degrees F. On castors with wheels. Built by Tolan. Item 10724-003 Unit sold as-is. Buyer is responsible for freight. We will load to truck. Crating and/or palletizing costs are extra. If you require assistance arranging freight. Please contact us at 856-287-2071. Payment is required prior to shipment. We buy and sell process equipment every day. Therefore. All items are subject to prior sale. We do our very best to immediately end the listing for any item that has been sold. For additional information or photos, please contact Scott at 856-287-2071 or via email at starzy@exllc.com. Please ask all questions prior to bidding.
Buy It Now
Condition: Used Location: Morris, United States Cherry-Burrell 130 Gallon Jacketed Stainless Steel Processor Tank - Mixing, Blending Tank. - Manufacturer: Cherry-Burrell, Cedar Rapids IA. - Dish Bottom ... moreto 2” TriClover TriClamp Center Outlet Connection.
Buy It Now
Condition: Used Location: Orlando, United States Large stainless steel food grade hopper with drain tube. Looks to hold 300-400 gallons.
Buy It Now
Condition: Used Location: Elkhart, United States One(1) Pre Owned Master Chemical XYBEX System1000 Coolant Recycling System for. Dirty Coolant Tank: 300 Gallons. Clean Coolant Tank: 450 Gallons. the ... moreMachinery Dealers National Association (MDNA). We have over 35,000 Sq Feet of Warehouse Space.
Buy It Now
Condition: Used Location: Hialeah, United States APV LIKWIFIER 330 gallon 316L S/S construction.
Buy It Now
Condition: Used Location: Hialeah, United States Uniloy Milacron Injection Stretch Blowmolding Machines mfg 2000 The total solution for cost effective versatile PET container production. Both machines ... moreinclude 10 cavity 48 oz cooking oil bottles. Blow Clamp Tonnage (US) 60.
Buy It Now
Condition: Used Location: San Dimas, United States JV Northwest 145-gallon stainless steel tank. Unit measures 36" diameter x 28" straight side with dome top and dish bottom. Unit is Teflon lined, has ... moresite tube, is rated for 35 PSI / Full Vacuum at 300 degrees Fahrenheit internal. Includes Tri-Clover top fittings (1) 8"; (3) 1-1/2" and (1) 2". Unit has 1-1/2" center bottom. Discharge Vessel is agitated with stainless steel enclosure for drive, 110-volt 175 RPM, 3/4" diameter x 32" long single prop with 3 blades, 10" diameter. Unit is portable on casters. Serial number 17246. Built in 2004. NB 727.
Buy It Now
Condition: New Location: Banning, United States Belovac C Class 24x48. size and cost by 40% of similar machines. Model BV C Class 24"x48" Vacuum Forming Machine. View Demo of a C Class forming a part ... moreFully adjustable material clamping. BV C Class 24"x48?.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 640608 NEW Air Oil Filter Compressor Screw IR GD Atlas Capco 640608 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-1432197aadf-0x100-
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6241271900 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6241271900 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
Condition: Used Location: Hiram, United States Groen 200G Double Motion Kettle Model SA F-200 SP Agitators: Full Sweep Agitator w/large Christmas Tree style center Agitator Agitator Electrical Specs: ... more5-HP/230V/3-P Manufacture Date: 1969 Kettle Dimension: Approx: 48”W x 34”deep Seller Note: Unit is USED with visible minor surface wear and some minor scratches none affecting the functionality or the intended use of the unit. Inside of the kettle is clean and free of any dried debris. What you see in the pictures is what is included in sale. Unit is being sold AS-IS, WHERE-IS, AS-SHOWN. Unit was tested at our facility with no mechanical issues noted during test. Pictures and are of the actual unit being purchased. If the buyer has any questions, please feel free to ask. Buyers are always welcome to come and personally inspect the unit.
Buy It Now
Condition: Used Location: Atlantic City, United States Above item has not been test run or inspected for completeness. It is being sold "as-is". Pick up from item location is free.
Buy It Now
Condition: Used Location: Atlantic City, United States Above item has not been test run or inspected for completeness. It is being sold "as-is". Pick up from item location is free.
Buy It Now
Condition: Used Location: Atlantic City, United States Above item has not been test run or inspected for completeness. It is being sold "as-is". Pick up from item location is free.
Buy It Now
Condition: Used Location: Albany, United States The tanks are designed for liquid and are approximately 300 gal.Tank dimensions are: TANK NO. 1--DIAMETER-48" X 60" X OVERALL HEIGHT 81" TANK NO. 2 -- ... moreHAS BEEN SOLD TANK NO. 3-DIAMETER-42" X 70" X OVERALL HEIGHT 90"Individually, the tanks are $2000 each. Two are available. All are cone bottom tanks. Buyer responsible for shipping cost and arranging pick up.
Buy It Now
Condition: Used Location: Mexico Above item has not been test run or inspected for completeness. It is being sold "as-is".
Buy It Now
Condition: Used Location: Mexico PETZHOLDT KM300 300 KG. THE INNER CONE HAS A SIDE AND BOTTOM SWEPT SURFACE AGITATOR, OUTER AREA HAS A SWEPT SURFACE AGITATOR, DRIVEN BY A 15-HP, 3 PHASE, ... more50 CYCLE, 380 VOLT MOTOR. Above item has not been test run or inspected for completeness.
Buy It Now
Condition: New Location: Banning, United States Belovac C Class 24x48. size and cost by 40% of similar machines. Model BV C Class 24"x48" Vacuum Forming Machine. Heater Panel: 12,000 watts infared radiant ... morepanel, with size-down option. industry tested machine.
Buy It Now
Condition: New Location: Banning, United States Belovac C Class 24x48. size and cost by 40% of similar machines. Model BV C Class 24"x48" Vacuum Forming Machine. View Demo of a C Class forming a part ... more12 months on all parts. BV C Class 24"x48” with upper tooling table option available.
Buy It Now
Condition: New Location: Banning, United States Belovac C Class 24x48. size and cost by 40% of similar machines. Model BV C Class 24"x48" Vacuum Forming Machine. View Demo of a C Class forming a part ... moreFully adjustable material clamping. BV C Class 24"x48?.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 5220925060 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6750558426 NEW Air Oil Filter Compressor IR GD Atlas Copco 67 505 58 426 MANN GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 521500 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air 521500 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 5081732 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air 5081732 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
Condition: New Location: Banning, United States Belovac LLC has been serving all industries for many decades and offers a time proven. Industry tested machine. With over 6000 satisfied customers world-wide. ... moreWe will provide you with an alternative to over built and over-priced equipment. Speak to a Belovac representative today! We offer a 24 hour hotline that is overseen by Mister J. Bell with over 30 years experience in machine design and product production development. You will be assisted and offered a very clear understanding of the process and the best options for your budget and production needs. Give us a call to discuss your needs! JB(951) 741-4822 Machine Featured: Model BV C Class 48"x96" Vacuum Forming Machine Model Features: Equipment is built to order. Lead time is 4 to 6 weeks. Depth of Draw: 17" female and 14" male tool Plastic clamping system: Full adjustable power strut easily adjusted to any size sheet. Featuring self-lifting frame. Heaters: Infrared radiant heater panel 63.000 watts with energy saving independent percentage control. Vacuum: 80 Gallon surge tank coupled with an industrial 15CFM high pressure vacuum pump Tooling table: Designed for heavy tools and optimum pressure 3 1/4 pneumatics; table offers adjustable L clamps for desired tool size Power: Standard 220 volts. Three phase 160 amps or 380 volts upgrade Tool vacuum box: Fitted with free vacuum box for demonstration. We fully test and operate your equipment prior to shipment Recommended for plastics: ABS-PVC-PETG-HIPS-HDPE-ACRYLIC(Recommended for most thermoplastics up to 1/4 inch) Air: requires 60 to 120 PSI air feed 1 CFM fitted with quick disconnect Controllers: Solid state programmable heater percentage control and heat time indicator Warranty Belovac equipment is fully covered under a 1 year guaranty of quality and workmanship. Any part's failure is covered by replacement, there are some exceptions to misuse or unauthorized alteration. Industries served: If it’s made from formed plastic. Belovac equipment probably made it. Universities Military bas e
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States C11158-1775 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 00771036 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air 0077 1036 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 2202260271 NEW Air Oil Filter Compressor Screw IR GD Atlas Capco 220 226 0271 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6750559236 NEW Air Oil Filter Compressor IR GD Atlas Copco 67 505 59 236 MANN GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States OC32 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air OC 32 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 4006.5104.2 NEW Air Oil Filter Compressor IR GD Atlas Copco 400651042 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 93568236 NEW Air Oil Filter Compressor IR GD Atlas Copco 9356 8236 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 92118678 NEW Air Oil Filter Compressor IR GD Atlas Copco 9211 8678 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00;1?RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2B%3E%3B1%3F-1432197aaa1-0xec-
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 93522720 NEW Air Oil Filter Compressor IR GD Atlas Copco 9352 2720 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6241271900 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6211412000 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6241271900 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6750558336 NEW Air Oil Filter Compressor IR GD Atlas Copco 67 505 58 336 MANN GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6750559016 NEW Air Oil Filter Compressor IR GD Atlas Copco 67 505 59 016 MANN GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 48221000 Fini NEW Air Oil Filter Compressor IR GD Atlas Copco 48221000 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 43552 NEW Air Oil Filter Compressor IR GD Atlas Copco 43 552 Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 4002.3102.2 NEW Air Oil Filter Compressor IR GD Atlas Copco Flottman 400231022 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 413 719 NEW Air Oil Filter Compressor IR GD Atlas Copco 413 719 Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 05500874 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air 0550 0874 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. ... moreThe oil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States C 16012-215 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The oil ... moreitself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
|