Buy It Now
$3.75 Shipping Condition: New Location: New Hampton, United States These are 3D printed in grey color. Replaces OEM wipers on Colchester Harrison 10AA Chipmaster, Colt and Bantam MK1 & MK2 and Bantam 2000. 12" x 24" Dominion. ... moreWe can make custom wipers for just about any lathe in a variety of materials including polyurethane rubber, plastic and felt or even a combination.
Buy It Now
Condition: Used Location: Pomona, United States Swing Over Gap: 23″. Distance Between Centers: 40″. Spindle Speeds (16): 33 – 2000. Bed Width: 11″. EQUIPPED WITH Electrical: 220/440V(Wired 220)/3PH. ... moreMotor HP: 7.5. Range of Cross Feeds (in. ).
Buy It Now
Condition: Used Location: Hugo, United States Clausing Colchester Triumph-VS Gap Bed Lathe 16" x 54". Swing: 16" (26" in gap). We'll do our best to get you the lowest rate possible. We also allow ... morelocal pick-up here at our facility in Hugo, MN 55038.
Buy It Now
Condition: Used Location: Bradenton, United States Gap Lathes. Gap Swing model: STANDARD MODERN 20/36-54 (1993). STANDARD MODERN. GENERATION MACHINE TOOLS, INC. Spindle Bore.
Buy It Now
Condition: Used Location: Holland, United States YODER MACHINERY SALES. DISTANCE BETWEEN CENTERS. 168". SWING IN GAP. . We load for free. SWING OVER WAYS. 27". STEADY REST 3 POINT. 17". SPINDLE SPEEDS. ... more. 40 TO 1500 RPM.
Buy It Now
Condition: Used Location: Warminster, United States Distance between centers- 40”. Swing over bed- 16”. Spindle speeds- 20 – 2000 R.P.M. F.O.B.: King of Prussia, PA – Disconnected, Prepped for. Machine ... moreas is. Cross feeds- 0.0008 – 0.011” in/rev. Longitudinal feeds- 0.002 – 0.03 in/rev.
Buy It Now
Condition: Used Location: Pomona, United States Swing Over Cross Slide: 8". Swing Over Bed: 14". Swing in Gap: 20". Distance Between Centers: 40". 10" 3-Jaw Chuck.
Buy It Now
$9.95 Shipping Condition: Used Location: Troy, United States It has a heavy cast iron bed with pyramidal rails 4 1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails. ... moreAbout 1 1/2". Wear and Tear dust and dirt rust and pitting but in good working condition.
Buy It Now
Condition: Used Location: Harrison, United States 15" X 40" BOLTON ENGINE LATHE. SPINDLE BORE. . 2". SPINDLE NOSE, CAMLOCK, SIZE. D1-5. SPINDLE SPEED RANGE(18). . 65 - 1,800 RPM. 8" 3-JAW CHUCK. 8" 4-JAW ... moreCHUCK.
Buy It Now
$10.95 Shipping Condition: Used Location: Troy, United States Marked on the inside P5476 WICO on the outside Part No. Y5479 WICO Electric Co. Springfield Mass. It has a heavy cast iron bed with pyramidal rails 4 ... more1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails.
Buy It Now
Condition: Used Location: Canada Distance between centers bed opened: 181". Distance between centers bed closed: 118". Swing over gap: 62". Maximum gap width bed open: 63". Swing over ... morebed: 33-1/16". Longitudinal feed range (60): 0.0007" – 0.0335".
Buy It Now
Condition: Used Location: Cincinnati, United States VICTOR GAP BED ENGINE LATHE. Swing Over Gap: 28-29/32". Swing Over Bed: 20". 10 HP Main Motor. Distance Between Centers: 40". Spindle Speeds: (12) 15 ... more- 1500 RPM. Hardened and Ground Bedways. Newall C-80 Two Axis Digital Readout.
Buy It Now
$9.95 Shipping Condition: Used Location: Troy, United States It has a heavy cast iron bed with pyramidal rails 4 1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails. ... moreWear and Tear dust and dirt rust and pitting paint loss but in good working condition.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Product parameters: Model: FZ102 Voltage: 110V Power: 180-200W Speed: 1400r/min Crushing chamber diameter: 102mm Screen aperture: 0.5, 1.0, 1.5mm (one ... moreinstalled on the machine) Crushing effect: 30-120 mesh Each crushing weight:
Buy It Now
Condition: Used Location: Waukesha, United States 16" 3 JAW CHUCK. MANUFACTURER.. VICTOR. SPINDLE SPEEDS. . (12) 21 TO 1500 RPM. CHUCK SIZE.. THREADS (ENGLISH). (24) 3.5 TO 26 TPI. MODEL. . 2040.
Buy It Now
Condition: New Location: Chatsworth, United States 13" x 40" Gap Bed Engine Lathe. Beautiful, new condition. Swing Over Gap. Swing Over Bed. Ask for Jerad. Length of Gap in Front of Face Plate, D1-4. Swing ... moreOver Cross Slide. Safety Foot Brake.
Buy It Now
Condition: Used Location: Hialeah, United States Thousands of Used Metalworking and Plastic Machines& New Machine Tools Photos, Full Descriptions and Prices- Fast& Easy About Us Shipping Payments& ... moreCheckout FAQs Our Inventory Home CNC Machines Manual Lathes. Mills, Drills, Saws Grinders. Hones, Finishing Fabricating Equipment Presses& Feeds Boring Mills Automatic Screw Machines EDMs Inspection Equipment Air Compressors Plastic Machinery Planers& Planer Mills Broaches& Keyseaters Shapers& Slotters Tooling& Accessories Welding Equipment Wire& Fastener Ovens. Furnaces& Environmental Misc Metalworking Gear Machinery Material Handling Misc Non-Metalworking 26" Swg 120" cc Summit 26-4 ENGINE LATHE. Inch/Metric, Taper, 4" Hole, 3-Jaw Ste Ref# 151984 iammdna XLATHE 26"39" x 120" SUMMIT GAP BED ENGINE LATHE MODEL: 26" S/N: K-02-07, NEW: 1998 SPECIFICATIONS: SWING OVER BED. 28" SWING OVER CROSS SLIDE. 19-1/2" SWING OVER GAP. 39" LENGTH OF GAP IN FRONT OF F.P. 19-1/4" DISTANCE BETWEEN CENTERS. 120" SPINDLE SPEEDS(16) 14- 1.010 RPM. SPINDLE NOSE CAMLOCK. D1-8" HOLE THRU SPINDLE. 4-1/8" THREADING- INCH(70) 1/2- 56 TPI. THREADING- METRIC(61) 5- 56. LONGITUDINAL FEED RANGE(70) 0014" 1664" CROSS FEED RANGE(70) 0007" 083" TAILSTOCK TAPER. 5MT. TAILSTOCK SPINDLE TRAVEL. 9-1/2" TAILSTOCK SPINDLE DIAMETER. 3-3/8" APPROX WEIGHT. 12.500 LBS. APPROX DIMENSIONS. 204"L x 5'W x 5'6"H. EQUIPPED WITH: INCH& METRIC THREADING. TAPER ATTACHMENT. 3-JAW CHUCK. RAPID TRAVERSE OF CARRIAGE. 2) STEADY RESTs. FOLLOW REST. FOUR WAY TOOLPOST. COOLANT SYSTEM. 15 HORSE POWER SPINDLE MOTOR. INSPECT UNDER POWER IN OUR NEW JERSEY WAREHOUSE CONDITION: EXCELLENT* Machine Location: HARRISON. NJ Click Her
Buy It Now
Free Shipping Condition: Seller refurbished Location: Winnetka, United States We Have Thousands Of Machine Manuals. Instruction Manuals. Machinery Maintenance Manuals. Parts list. Service Manuals. Machinery Brochures And Schematics ... moreFor Sale. We Are Proud To Provide Service To The Metalworking. Chip Making and Fabricating Machine Tool Manual Needs. We Take Great Pride In Getting You The Correct Manual For Your Machine. Let Us know Your Serial Number. And Model Number. We Guarantee That We Will Get You a Correct Manual or Your Money Back! Each Manual Is Comb Bound For Easy Reading On A Flat Surface Such As a Table or Workbench. We Have Collected These Manuals Over Many Years And Continue To Look For More Every Day. Our Customers Have Been Pleased With Our Manuals. Schematics, Parts List, Service Manuals, Maintenance Manuals, Instructions Manuals And Brochures. They Are Filled With Invaluable Information, Sometimes Not Even Available Direct From The Manufacturer. We Are Often The Last Resort. We Take Pride In This Fact. We Are Here To Fulfill Your Industrial Machinery Manual Needs Today. Email Us Today! Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false MicrosoftInternetExplorer4 Normal 0 false false false M
Buy It Now
Condition: Used Location: Dayton, United States Center distance - 60". Spindle speeds (16) - 30 to 1800 rpm. Swing over bed - 16". Weight, approx - 4400 lbs. Newall Digital Readout. Equipped with Swing ... moreover gap - 23 1/2". Swing over cross slide - 10 1/4".
Buy It Now
Condition: Used Location: Harrison, United States 20"/26" X 80" LION GAP BED ENGINE LATHE. QUILL TAPER BORE. 5MT. SWING IN GAP. . 26". SPINDLE NOSE CAMLOCK. SPINDLE SPEED RANGE (15). 19 - 2400 RPM. SPINDLE ... moreBORE. . 2-7/16".
Buy It Now
Free Shipping Condition: New Location: Durham, United States The way wipers are made from hard, die-cut felt which is precisely sized to fit the profile of the lathe bed V-ways or flats. The wipers serve two purposes. ... moreSince every size of South Bend Lathe had different sized ways, every lathe had its own specially designed wiper set that compressed tightly against the way.
Buy It Now
Condition: Used Location: Toledo, United States 2 AXIS FAGOR DRO.. SWING IN GAP.. SWING OVER BED.. 36". DISTANCE BETWEEN CENTERS. 120". YEAR NEW. 2011. SPINDLE SPEEDS.. (16) 30 - 1400 RPM.
Buy It Now
Condition: Used Location: Cincinnati, United States 40"/49.25" x 170" POREBA GAP-TYPE ENGINE LATHE #29356. Swing thru Gap 49.25". Distance Between Centers 170". Hole Thru Spindle 4.7". (21) Spindle Speeds, ... moreRange 5 to 500 RPM. (70) DP Threads, Range 1/2 to 60 TPI.
Buy It Now
Condition: Used Location: Louisville, United States Good running lathe, can be seen under power. Free loading. 12" Burnerd 3 Jaw Chuck (chuck has 4" Thru Hole). Spindle Bore 3". Coolant Tank (pump has not ... morebeen tested). Centers 60". Power 7.5 hp. RPM 1,600 RPM.
Buy It Now
Condition: Used Location: Millersburg, United States In Good Used Condition. Tested @480V. Swing Over Bed: 25" Swing in Removable Gap: 34" Swing Over Cross Slide: 11-1/2" Distance Between Centers: 118" Hole ... moreThru Spindle: 2-3/4" Slide Table Travel: 14" 16" 3-Jaw Chuck. 5-Pin Adapter. 4-Position Indexer. Angle slide attachment on side needs minor repair to be functional. Floor Space: 183"x 30" We don't have any rests for the lathe. .
Buy It Now
Free Shipping Condition: New Location: Durham, United States The way wipers are made from hard, die-cut felt which is precisely sized to fit the profile of the lathe bed V-ways or flats. The wipers serve two purposes. ... moreSince every size of South Bend Lathe had different sized ways, every lathe had its own specially designed wiper set that compressed tightly against the way.
Buy It Now
$16.85 Shipping Condition: Used Location: Rehoboth, United States Delta lathe steady rest In good working order, does need cleaning Fits bed 1 1/2" bed gap .
Buy It Now
Free Shipping Condition: New Location: Durham, United States The way wipers are made from hard, die-cut felt which is precisely sized to fit the profile of the lathe bed V-ways or flats. The wipers serve two purposes. ... moreSince every size of South Bend Lathe had different sized ways, every lathe had its own specially designed wiper set that compressed tightly against the way.
Buy It Now
Free Shipping Condition: New Location: United States This will reduce any smoke, soot or warpage of the workpiece you are working on. The beehive grid does reduce smoke and burning on the back of the workpiece ... morewhen cutting. When you hold it, it will not deform.
Buy It Now
Condition: Used Location: Los Angeles, United States
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States Product parameters: Model: FZ102 Voltage: 110V Power: 180-200W Speed: 1400r/min Crushing chamber diameter: 102mm Screen aperture: 0.5, 1.0, 1.5mm (one ... moreinstalled on the machine) Crushing effect: 30-120 mesh Each crushing weight:
Buy It Now
Free Shipping Condition: New Location: Chino, United States Product parameters: Model: FZ102 Voltage: 110V Power: 180-200W Speed: 1400r/min Crushing chamber diameter: 102mm Screen aperture: 0.5, 1.0, 1.5mm (one ... moreinstalled on the machine) Crushing effect: 30-120 mesh Each crushing weight:
Buy It Now
Free Shipping Condition: New Location: Durham, United States The way wipers are made from hard, die-cut felt which is precisely sized to fit the profile of the lathe bed V-ways or flats. The wipers serve two purposes. ... moreSince every size of South Bend Lathe had different sized ways, every lathe had its own specially designed wiper set that compressed tightly against the way.
Buy It Now
Condition: Used Location: Pomona, United States Mimik Tracer. Swing Over Bed: 17". Distance Between Centers: 40". Spindle Speeds: (12) 32-1800 RPM. Main Motor: 5 HP. Wheeler Machinery Sales, Inc. Spindle ... moreHole: 2-1/4". Pomona CA 91768.
Buy It Now
Condition: Used Location: Louisville, United States Webb 17Gx40 lathe. This gap bed engine lathe has a 40" bed and a 17" swing, 25" with the gap removed. Spindle bore is 2-1/16" with a spindle speed of ... more32-1800 RPM. Equipped with 5 HP, 220-440 VAC motor.
Buy It Now
$3.95 Shipping Condition: Used Location: Troy, United States Local Pick-up Available.
Buy It Now
$4.95 Shipping Condition: Used Location: Troy, United States Local Pick-up Available.
Buy It Now
$9.95 Shipping Condition: Used Location: Troy, United States It has a heavy cast iron bed with pyramidal rails 4 1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails. ... moreThere are 2 adapters one a #1 to #2 MT adapter the other a #2 to #3.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Product parameters: Model: FZ102 Voltage: 110V Power: 180-200W Speed: 1400r/min Crushing chamber diameter: 102mm Screen aperture: 0.5, 1.0, 1.5mm (one ... moreinstalled on the machine) Crushing effect: 30-120 mesh Each crushing weight:
Buy It Now
Free Shipping Condition: New Location: Chino, United States Mill Plant Machine FZ102 Grinder Micro Plant Grinding Machine110V 1400r/m TOP. The machine uses a high-speed rotating knife and fixed knife to form a ... morecutting surface for crushing, which generates little heat.
Buy It Now
Condition: Used Location: Hamilton, United States Centers 60". Power 10 hp. 3-Jaw Chuck. Equipped With.
Buy It Now
$3.95 Shipping Condition: Used Location: Troy, United States
Buy It Now
Condition: Used Location: Toledo, United States GEMINIS ENGINE LATHE. SWING IN THE GAP. LENGTH OF GAP. 12". SWING OVER BED. . 40". SPINDLE HOLE. . DISTANCE BETWEEN CENTERS. 72". (18) 16 TO 1250 RPM.
Buy It Now
$750.00 Shipping Condition: Used Location: Fairborn, United States This is a Millport Lathe, model 1540. It has a 15” swing and is 40” between centers. It is a gap bed lathe. It has a few accessories that go with it, ... moreas can be seen in the pictures. The buyer can pick it up or have it shipped. All shipping and packing and handling charges are the responsibility of the buyer. Any questions, feel free to message through Ebay.
Buy It Now
Condition: For parts or not working Location: Euclid, United States Model Number: ENTERPRISE 1550. Manufacturer: MK. (c) Truckload and Partial Truckload: HGR can assist you in setting up truckloads or partial truckload ... moreloads (flat bed, step deck, double drop, etc.). We will provide you with a competitive rate that is only valid if prepaid on our account.
Buy It Now
Condition: New Location: Ontario, United States Digital readout (DRO) unit with X- and Z-axis optical scales included for ease of operation. Digital readout (DRO). Main Motor 1-1/2HP, single-phase, ... more220V. Swing over Bed 13". Swing over Gap 19-1/4". Swing over Cross Slide 7- 5/8".
Buy It Now
$4.95 Shipping Condition: Used Location: Troy, United States
Buy It Now
Condition: For parts or not working Location: Euclid, United States Manufacturer: KBC. (c) Truckload and Partial Truckload: HGR can assist you in setting up truckloads or partial truckload loads (flat bed, step deck, double ... moredrop, etc.). We will provide you with a competitive rate that is only valid if prepaid on our account.
Buy It Now
$10.95 Shipping Condition: Used Location: Troy, United States It has a heavy cast iron bed with pyramidal rails 4 1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails. ... moreWear and Tear dust and dirt rust and pitting and paint loss in good working condition.
Buy It Now
Condition: Used Location: Pomona, United States Manufacturer: Poreba. Distance Between Centers: 120". Swing In Gap: 42". Swing Over Bed: 32". - 32" 4 Jaw Chuck. Cross Slide Travel: 16". Spindle Nose: ... moreA1- 11. - 2 Large Roller Type Steady Rest.
Buy It Now
Condition: Used Location: Holland, United States SWING IN GAP 28". SWING OVER BED 20". DISTANCE BETWEEN CENTERS 120". HOLE THROUGH SPINDLE 4". SPINDLE SPEEDS (12) 22 TO 1,500 RPM. STEADY REST 8" ROLLER. ... moreCHUCK 12" 3 JAW. MOTOR 10 HP.
Buy It Now
$59.05 Shipping Condition: Used Location: Troy, United States It has a heavy cast iron bed with pyramidal rails 4 1/4" apart center to center. The bed is 6" from front to back and has a 2 3/8" gap between bed rails. ... moreWear and Tear dust and dirt rust and pitting and paint loss in good working condition.
Buy It Now
Condition: Used Location: Holland, United States YODER MACHINERY SALES. SWING IN GAP. . 35-7/16". DISTANCE BETWEEN. . 72". We load for free. SPINDLE HOLE.. 4-1/16". May inspect under power. SPINDLE SPEEDS. ... more.
Buy It Now
Condition: For parts or not working Location: Euclid, United States Model Number: SN 40B. Manufacturer: TOS. (c) Truckload and Partial Truckload: HGR can assist you in setting up truckloads or partial truckload loads (flat ... morebed, step deck, double drop, etc.). We will provide you with a competitive rate that is only valid if prepaid on our account.
Buy It Now
Free Shipping Condition: New Location: Bellingham, United States G0776 13" x 40" Gunsmithing Lathe w/ DRO. G0776 13" x 40" Gunsmithing Lathe with DRO. Supplied with a 2 HP motor, the 8-speed gearhead of the G0776 produces ... morespindle speeds from 70-2000 RPM. The G0776 includes a two-axis digital readout, so accuracy and precision are ensured!
Buy It Now
Condition: Used Location: Harrison, United States 29"/37" x 60" ACER GAP BED ENGINE LATHE.5 - 14 mm. MODEL: DYNAMIC 29120G, S/N: N7010022, MFG: 2007. -SONY TWO AXIS DIGITAL READOUT. - THREAD CHASING DIAL. ... moreDISTANCE BETWEEN CENTERS. 60".
Buy It Now
Condition: Used Location: Holland, United States YODER MACHINERY SALES. DISTANCE BETWEEN CENTERS. 118". SWING IN GAP. . SWING OVER BED. 24". We load for free. STEADY REST. 7" ROLLER. CHUCK. 21" 4 JAW.
Buy It Now
Condition: Used Location: Orange City, United States Greenway Product Number: 10919. Maximum distance between centers.. 120”. 19” 4 jaw chuck. Floor space... 16’ 7” x 48”.
Buy It Now
$183.38 Shipping Condition: Used Location: Valencia, United States The Maestro 3 separates both small and large pre-scored PCBs. The circular and linear blades made from a special steel ensure a long service life. The ... morepre-scored grooves can be interrupted by any number of cut-outs.
Buy It Now
Free Shipping Condition: New Location: Minooka, United States Center Drill,Plain,#8. CLEVELAND C04416 Screw Machine Drill,#36,HSS. Grainger Part #:1DBK4. Diversion contrary to U.S. law is prohibited. administered ... moreby BIS, and the International Traffic in Arms Regulations administered by DDTC.
|