|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
$3.00 Shipping Condition: New Location: China Description This module is blue PCB now.Please know it. The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping ... morebipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting. Overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) 1）Simple step and direction control interface 2）Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 3）Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 4）45 V maximum supply voltage 5）Built-in regulator(no external logic voltage supply needed) 6）Can interface directly with 3.3 V and 5 V systems 7）Over-temperature thermal shutdown. Over-current shutdown, and under-voltage lockout 8）Short-to-ground and shorted-load protection 9）4-layer. 2 oz copper PCB for improved heat dissipation 10）Exposed solderable ground pad below the driver IC on the bottom of the PCB 11）Module size. Pinout, and interface match those of our A4988 stepper motor driver carriers in most respects(see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet(1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil(see the Power Dissipation Considerations section below for more information) Here are some of the driver’s key
Buy It Now
Free Shipping Condition: Used Location: Boise, United States You can use the.
Buy It Now
$7.00 Shipping Condition: New Location: Colorado Springs, United States Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip.Can drive one 2-phase stepper motor, one 4-phase stepper ... moremotor or two DC motors. High working power to 35v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Buy It Now
Free Shipping Condition: New Location: Lakeland, United States This STMicrroelectronics X-NUCLEO-IHM06A1 Expansion Board Stepper Motor Driver is a powerful tool for industrial automation and motion control. It boasts ... morea brand of LIFE.AUGMENTED and is new and sealed. The R2V3 functional and cosmetic aspects are also top-notch, making it a highly reliable option for those in need of drives and motor controls. This expansion board is specifically designed for stepper motor drivers, making it an ideal choice for those looking for precise and efficient control in their automation and motion control systems. With its top-of-the-line features and exceptional performance, this board will surely meet the needs of any industrial application.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 3 Axis TB6560 CNC Stepper Motor Driver Board 1.5A-3A*NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller Product Features: Toshiba TB6560AHQ chip- High ... morepower. Maximum 3.5A drive current chipset! 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step, Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors*Attention: This driver is 1.5A-3A version. Which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A. If the rated current your stepper motors is below 1.5A. You can choose the 0.5A-2.5A version. Please let us know which version(1.5A-3A version is default) you need immediately after placing an order. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Deta
Buy It Now
$20.50 Shipping Condition: For parts or not working Location: Saint Paul, United States
Buy It Now
$3.20 Shipping Condition: New Location: China Dual DC Stepper Motor Drive Controller Board Module TB6612FNG Replace L298N Description: Description: The TB6612FNG motor driver can control up to two ... moreDC motors at a constant current of 1.2A(3.2A peak) Two input signals(IN1 and IN2) can be used to control the motor in one of four function modes- CW. CCW, short-brake, and stop. The two motor outputs(A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode.CJMCU. Logic supply voltage(VCC) can be in the range of 2.7-5.5VDC. While the motor supply(VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel(or up to 3.2A for a short. Single pulse) Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other. Features: Power supply voltage: VM=15V max. VCC=2.7-5.5V•Output current: Iout=1.2A(average) 3.2A(peak) Standby control to save power•CW/CCW/short brake/stop motor control modes•Built-in thermal shutdown circuit and low voltage detecting circuit•All pins of the TB6612FNG broken out to 0.1" spaced pins•Filtering capacitors on both supply lines Feedback: We will leave 5 Star psitive Feedback after receiving the payment.5 Star Feedback is our life. Please help do not leave a neutral or negative feedback and Low score. Please do contact us to get a better solution! Your understanding will be appriciated! We believe all the problems can be solved if buyer works with us I am a honest seller. Please 100% trust! Your sasifation is our final goal! Our best service will let you 100% satisfy! Hope also to receive your 5 star positive feedback! Note: The economy shipping will be no tracking number. Only have the recording number to prove it sent If you need the track
Buy It Now
Free Shipping Condition: New Location: Sebastian, United States Item condition: Item condition: To find in the Item specifics(top of description MENU tap) and all above pictures. In the picture. You can find the defect, ... morescratch, and test if any. If pictures are not clear, please advise me. You can find the" Technical specification" in the Google.com and product WEB link. Thank you. Shipping Info: Usually Items send out within 1 working day after receiving cleared payment. Shipping time 18-26 Days for Economy international/ Free Shipping. Shipping time 7-10 Days for Expedited international Shipping. Varies for items shipped to an international location depend on local post. Shipping service and receipt of Delivery times may vary. Especially during peak periods. Track& Confirm: The registered and tracking number will be see in the eBay purchased history and PayPal after shipment. Could you please to enter your item tracking number at link following. http:track.thailandpost.co.th/trackinternet/Default.aspx?lang=en In the United States can track item at below. https:trkcnfrm2.smi.usps.com/PTSInternetWeb/index.jsp or https:tools.usps.com/go/TrackConfirmAction.action Question: If you have any question about the item. Feel free to email us at eBay messages. I will do my best to answer. Thank you for interesting and let me know. Feedback: The 5 star Positive feedback is very important to me. I need to high standards of excellence 100% customer satisfaction. Could you please contact me immediately to satisfactorily solve problem for best service. Would not give me unfair. Neutral or negative feedback. Thank you. Payment: We accept only Get PayPal buyer protection for your item when you pay with PayPal. Return: See in the returns policy at tab shipping and payments. We appreciate your business. On Jan-26-12 at 21:26:57 PST. Seller added the following information:
Buy It Now
$16.23 Shipping Condition: New Location: San Jose, United States
Buy It Now
Free Shipping Condition: New Location: United States
Buy It Now
Free Shipping Condition: New Location: Raleigh, United States For 42, 57 3A stepper within two-phase / four-phase / four-wire / six-wire stepper motor is not suitable for more than 3A stepper motor. The maximum rated ... moreoutput: ± 3A, peak 3.5A. 5, using a fine-toothed thick radiator, good heat dissipation.
Buy It Now
Free Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. Due to the difference between different monitors, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Supports connection of electronic handwheel. Supports 4 -axis linkage and can connect 4 stepper motor drivers or drivers;. 1 status LED, indicating the ... moreconnection status on the board. 1 x USB cable. Support limit switch.
Buy It Now
Free Shipping Condition: New Location: China High input speed of optoelectronic isolation signal. If you do not receive our reply within 48 hours, pls. If you are satisfied with our service, pls. ... moreSingle-chip PWM bipolar sine chopper ensures low vibration and high efficiency.
Buy It Now
Free Shipping Condition: New Location: Brentwood, United States Dual motor driver chip L9110S. 6 Dual L9110S DC Stepper Motor Driver Board. Double L9110S chip motor drive. Dual L9110S DC Stepper Motor Driver Board ... moreH-Bridge Motor drive. Can drive two DC motors, or a 4-wire 2 -phase stepper motor.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States This includes a custom built tinned braided copper shielded cable for the signal leads run to the G540 from the PROMA. (Review the video below). · Gecko ... moreG540 Rev8 latest 2020 edition 4 axis digital driver integrated system (. ).
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States 2pcs Angle Grinder Accessories Shield Cover Conversion Angle Grinding Tool. It can directly drive two 3-35V DC motor. This dual L298N driver module, using ... moreST's L298N chip, and high stability process, with high-quality electrolytic capacitors to make the circuit work stably.
Buy It Now
Free Shipping Condition: New Location: China The mode needs to be set in [F5-F8] function. Feature: 1. This module has no programmable function, but built in a variety of fixed operation mode, the ... moreuser can quickly choose the appropriate trajectory.
Buy It Now
Free Shipping Condition: New Location: China The DM870 stepper drive is designed to power 2 phase (1.8°) or 4-phase (0.9°) NEMA23, 24 and 34 hybrid stepper motors. Auto-tuning to match wide-range ... moreNEMA 23, 24, 34 stepper motors. Soft-start with no "jump" when powered on.
Buy It Now
Free Shipping Condition: New Location: Hainesport, United States ▶Stepper Motor:X/Y1/Y2/Z. The positive and negative of the input power must not be reversed, and the reverse connection will burn. ▶Connect Laser:2pin/3pin/2pin-2pin. ... moreConnect Spindle：. Connect Laser.
Buy It Now
Free Shipping Condition: New Location: Sacramento, United States Can be accessed by a total of Yang or common cathode, the input level of 5v, with optocoupler input stepper motor driver. Providing an electronic hand ... morewheel interface. [COMPATIBILITY] --- Support various versions of MACH3 software, support for the latest version.
Buy It Now
Free Shipping Condition: New Location: China Feature: 1. This module has no programmable function, but built in a variety of fixed operation mode, the user can quickly choose the appropriate trajectory. ... more8- The value of the inversion in place delay (i.e., the value of [P7]) in seconds.
Buy It Now
Free Shipping Condition: New Location: United States Product Name: 1pcs Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for arduino Basic Attributes Name Double H Bridge Motor Driver Module ... moreWorking mode Drived by H bridge(double lines) Control chip L298N? ST? Logical voltage 5V Driving voltage 5V? 35V Logical current 0mA-36mA Driving current 2A(MAX single bridge) Storage temperature? 20? +135? Maximum power 25W weight 30g Periphery dimension 43*43*27mm Product features: 1.Using L298N made by ST company as the control chip.The module has such characteristics as strong driving ability.Low calorific value and strong anti-interference ability. 2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip.Please use an external 5V logic supply when using more than 12V driving voltage. 3.Using large capacity filter capacitor.This module can follow current to protect diodes,and improve the reliability Real figure? L298N is a kind of high voltage.High current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V)large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well. Port function? Circuit principle diagram? This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V. It can enable the on
Buy It Now
$3.00 Shipping Condition: New Location: China Adafruit Arduino Motor/Stepper/Servo Shield Kit v2.3 Don't wait 30+ days to get a simular item China! Description Resistors Direct is a privately ... moreowned US business full of fun hard working people. We sell only products that we would personally use. Most items are shipped the next business day following receipt of payment. Shipments are sent using USPS. FedEx, and UPS and typically take 2 to 5 business days to arrive at most U.S. locations. At Resistors Direct your questions will be answered as quickly as possible and issues will be resolved promptly. Please call us if you need additional assistance at(402) 404-6972. If we miss you. Please leave us a message. Package Includes: 1- Adafruit Arduino Motor/Stepper/Servo Shield Kit v2.3 Details: The original Adafruit Motorshield kit is one of our most beloved kits. Which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver. We now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries. And there are built-in flyback diodes as well. Instead of using a latch and the Arduino's PWM pins. We have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Only two pins(SDA& SCL) are required to drive the multiple motors. And since it's I2C you can also connect any other I2C devices or shields to the same pins. This also makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but i
Buy It Now
Free Shipping Condition: New Location: China Axis: 1, 2, 3 or 4 (X, Y, Z, C). X, Y, Z, C axis can conduct linear interpolation, X, Y can do circular interpolation. Programming Function Introduction ... moreMachine Zero: Go back to machine zero. Output: Define on and off of output port, ex.
Buy It Now
$45.00 Shipping Condition: New Location: China 3DM3722 driver greatly improves stability and reduces noise under low subdivision. The drive current effective value from 1.2A /phase to 7.0A / phase. ... moreautodetect switch （ OFF=receive outside pulse, ON=The stepper motor drive rotate at 30RPM ）.
Buy It Now
Free Shipping Condition: New Location: China This product is a drive module developed for inductive BLDC motor. The drive master chip is SNR8503M, and the special circuit for inductive motor drive ... moreis integrated inside the chip, supporting the Hall electric Angle of 120 degrees or 60 degrees, and the default is 120 degrees.
Buy It Now
$3.00 Shipping Condition: New Location: China
Buy It Now
$11.67 Shipping Condition: New Location: China The DM556 stepper drive is designed to power 2 phase(1.8°) or 4-phase(0.9°) NEMA17, 23 and 24 hybrid stepper motors. Auto-tuning to match wide-range NEMA ... more17, 23, 24 stepper motors. Soft-start with no "jump" when powered on.
Buy It Now
Free Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. Due to the difference between different monitors, the picture may not reflect the actual color of the item.
Buy It Now
Free Shipping Condition: New Location: Wichita, United States Control package off a CNC3020 CNC rout. We needed the table and spindle, but we did not need the control system.
Buy It Now
$1.99 Shipping Condition: New Location: Los Angeles, United States Applicable stepper motor: 42,57,86 type 2. 3, eight output current optional, the maximum output. 9, provide energy-efficient semiautomatic current lock ... morefunction;. 1x Microstep Driver. phase 4-phase (4-wire 6 wire line 8).
Buy It Now
Free Shipping Condition: Used Location: Hannibal, United States We stand behind our products. Great item at a great price!
Buy It Now
Free Shipping Condition: New Location: China We promise try our best to help solve any problem.
Buy It Now
Free Shipping Condition: New Location: Joliet, United States Note: TMC2208 driver needs extra fan to cool it, otherwise the high temperature may destroy it. Compatible with existing 3D printer electronics, eliminating ... morethe expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market.
Buy It Now
$45.00 Shipping Condition: Used Location: San Jose, United States Nanosolutions Orsay Physics, Gilovs Main Board, P/N 3223001000.
Buy It Now
$2.99 Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. Color: See pictures.
Buy It Now
$6.05 Shipping Condition: New Location: Pleasant Hill, United States L298N Dual H Bridge DC Stepper Servo Motor Driver Controller Board Arduino
Buy It Now
$2.00 Shipping Condition: New Location: China It can drive 4-wire, 8-wire two-phase stepper motor. 1x Stepper Motor Driver. Due to the light and screen difference, the item's color may be slightly ... moredifferent from the pictures. Current output range: 0.2-2A.
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States 3 x Stepper Motor Driver 3 x Heat Sink 3 x Screwdriver. Baker's Canvas Cloth for French Loaves & Bread Proofing. - Compatible with existing 3D printer ... moreelectronics, with a standard step/ interface, it is easy to use.
Buy It Now
Free Shipping Condition: For parts or not working Location: Saint Paul, United States
Buy It Now
Free Shipping Condition: For parts or not working Location: Glen Flora, United States I was able to power this up and observe the green power light flash for several seconds then the power light shuts off altogether, all while the red alarm ... morelight stays on. Because of our inability to fully test this item it will be sold for parts or repair.
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: United States Adaptive motor: Stepper motor. The distance / speed / delay / number of cycles can be saved and set after power down. It can run independently as a module, ... moreor it can be used together with other systems.
Buy It Now
Free Shipping Condition: New Location: Jamaica, United States Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. Instead of using a latch ... moreand the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard.
Buy It Now
$0.23 Shipping Condition: New Location: China Features: The upgraded version of TB6600 is a driver suitable for 57/42 type two-phase hybrid-stepping motor with phase current under 4.0A. Model: TB6600. ... moreApplication: for 42/57 stepper motor. Set 7 kinds of subdivisions (1/2A/2B/4/8/16/32) through 3-bit DIP switches, and 8 gear output current (0.5A/1.0A/1.5A/2.0A/2.5A/2.8A/3.0A/3.5A).
Buy It Now
Free Shipping Condition: New Location: Navarre, United States Minimal pulse width of 2.5μs. Also swapping the connection of two wires of a coil (e.g. A+ and A-) to the drive will reverse motor direction. Enable signal: ... moreThis signal is used for enabling/disabling the drive.
Buy It Now
Free Shipping Condition: New Location: United States It has achieved a unique level of system smoothness, providing optimal torque and nulls mid-range instability that is suitable for Cnc drive. 16 selectable ... moremicrostep resolutions including 400, 800, 1600, 3200, 6400, 12800, 25600, 51200, 1000, 2000, 4000, 5000, 8000, 10000, 20000, 40000.
Buy It Now
Free Shipping Condition: New Location: China Maximum load current 12A(without heat dissipation), 15A(simple heat dissipation), 20A(thick large radiator); Instantaneous peak current 110A. PWM minimum ... moreeffective pulse width: 200ns. Maximum load current.
Buy It Now
Free Shipping Condition: New Location: United States Microstep:1~200. Fit within 5A, NEMA.23~42 stepper motor;. Current: 5A Max. Input VAC : 110~220V AC. Great News from Wantaimotor!
Buy It Now
Free Shipping Condition: New Location: China L298N Dual H Bridge DC stepper Motor Driver Controller module Board for Arduino. Principle diagram: Features: Driver: L298N Dual H Bridge DC Motor Driver ... moreIC The terminal supply area of driven part Vs: +5 V ~ +35 V; such as the need to take power within the board. The supply area Vs: 7V ~ 35V The peak current of driven part Io: 2A the terminal supply of area the logical part Vss: +5 V ~ +7 V(can take power within the board +5 V) the operating current range of the logical part: 0 ~ 36mA control signal input voltage range: Low:0.3V ≤ Vin ≤ 1.5V High: 2.3V ≤ Vin ≤ Vss enable signal input voltage range: Low: 0.3 ≤ Vin ≤ 1.5V(control signal is invalid) High: 2.3V ≤ Vin ≤ Vss(control signal active) Maximum power consumption: 20W(when the temperature T = 75 °C) Storage temperature: 25 °C ~ +130 °C Driver Board Size: 55mm* 49mm* 33mm(with fixed copper pillar and the heat sink height) Driver Board Weight: 33g Other Extensions: control of direction indicators. The logic part of the plate to take power interface. X-058. ● We only accept paypal payments. ● When we receive your payment. We will be help you arrange shipping in 2 working days. Weekends and holidays do not break) ● All our parcels are shipped via China Post.Can provide Following two Delivery mode： Airmail It takes about 15-25 days EMS(Express Mail Service) It takes about 7-14 days ● Buyer should expect to pay any amount charged by the government of bidder's country; this includes but not limited to duty& tax ● Shipping& handling fees are non-refundable. ● If you haven’t received the item in one month. We will refund to you.PLEASE INSPECT YOUR ITEMS WHEN THEY ARE RECEIVED） ● Once you receiving the item with satisfaction. Please leave us positive feedback, and 5 STAR DSR. Thank you! ● If you feel dissatisfied with the products receive. Please could you should first contact us using e-mail. Please do not impulsively give a Neutral or Negative feedback before giving us the opportunity to resolve you problem! Neutral and Negative feedback wi
Buy It Now
Free Shipping Condition: New Location: China 8- The value of the inversion in place delay (i.e., the value of [P7]) in seconds. Feature: 1. This module has no programmable function, but built in ... morea variety of fixed operation mode, the user can quickly choose the appropriate trajectory.
Buy It Now
Free Shipping Condition: New Location: China Stepper Driver – TB6600 4A 40V Features Support 8 kinds of current control Support 7 kinds of micro steps adjustable The interface adopts high-speed optocoupler ... moreisolation Automatic semi-flow to reduce heat Large area heat sink Anti-high-frequency interference ability Input anti-reverse protection Overheat, over current and short circuit protection Specifications Input Current: 0-5A Output Current: 0.5-4.0A Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Dimension: 96x56x33 mm Weight: 0.2 kg.
Buy It Now
$3.50 Shipping Condition: New Location: China Max Drive Current: 4A. High-speed optocoupler signal isolation input. Electrical input signal is TTL compatible. Otherwise deal is final. Bipolar constant ... morecurrent chopper. Stationary current is automatically reduced by half.
Buy It Now
Free Shipping Condition: New Location: China Support for connecting electronic handwheel;. 4 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero and ... moreother device. 1 x USB cable. 1 status LED, indicate connection status on the board.
Buy It Now
Free Shipping Condition: New Location: China Feature: 1. PUL = PULS = CLK pulse. If you do not receive our reply within 48 hours, pls. If you are satisfied with our service, pls.
Buy It Now
Free Shipping Condition: New Location: China Subdivision selection range 1-128 subdivision.
Buy It Now
Free Shipping Condition: New Location: China Application: Stepper Motor, DC Motor. Feature: 1. Adjustable Speed Range: 0.1~999 rpm.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Set Standard ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States Piece of 18AWG 4 leadDouble Shielded DS Flexion Robotics Grade Cable. DS Flexion 18awg Motor Retrofit Cable Kit. Here's an overview video of DS Flexion ... moreCable. DS Flexion Ultra Flex Double Shielded Robotics Cable Is Here!
|
|
|
 |