|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: New Location: China 5PCS A4988 StepStick Stepper Motor Driver Module for 3D Printer Reprap Heat sink Description Features: A4988 is a complete microstepping motor driver ... morewith built-in translator for easy operation. The product can be full. Half, 1/4, 1/8 and 1/16 step mode to operate bipolar stepper motor output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator. The regulator can slow or mixed decay mode. The converter is the key to the easy implementation of the A4988. In inputting one pulse on the STEP input drives the motor one microstep. No phase sequence tables, high frequency control lines, or complex interfaces to programming. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. Micro-step operation. The chopping control in the A4988 automatically selects the current decay mode(Slow or Mixed) In the mixed decay mode, the device is initially set to fast decay in the part of the fixed off-time, then a slow decay in the rest of the downtime. Mixed-decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry to improve the pulse-width modulation(PWM) power consumption when operating. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout(UVLO) and crossover current protection. Special power-Sort. A4988 surface mount QFN package(ES) The size of 5 mm × 5 mm nominal overall package height of 0.90 mm . And with exposed pad for enhanced thermal dissipation. The package is Pb(suffixes-T) with 100% matte tin leadframe plating. Specifications: Low RDS(ON) outputs· Automatic current decay mode detection/ selection· Internal UVLO· Mixed with slow current decay m odes· Synchronous rectification for low power dissipation· Crossover-current protection· Thermal shutdown circuitry· 3.3 and 5 V compatible logic supply· Thermal shutdown circuitry· Ground Fau
Buy It Now
$12.95 Shipping Condition: New Location: Hoffman Estates, United States 3 pcs 270 oz-in stepper motors, NEMA23.
Buy It Now
Free Shipping Condition: New Location: 金东区, China The DRV8825 stepper motor driver carrier is the breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. DRV8825 has adjustable current ... morelimit, overcurrent and overheat protection, and six microstep resolutions (down to 1/32 step).
Buy It Now
Free Shipping Condition: New Location: United States World Shipping. 7 Days Money Back. CNC 5 Axis Breakout Board For Stepper Driver Controller Mach3/ EMC2/ KCAM4 DB25 More. PCB Instructions& Specifications, ... moreThe latest 3rd generation breakout board has been upgraded to the intelligent. Professional and industrial-level interface board set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation breakout board set has two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the" computer G-code recording function" And another is the" manual programing function" Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will make the breakout board control the microstep drivers more smoothly with lower noise. With the embedded intelligent memory chip. The professional version of this 3rd generation 5 Axis breakout board can easily record MAXIMUM 4 Axis' X. Y, Z, A Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4, etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-code recording function is enough for all the four axis working without computer, to avoid repeated function, the manual programming function is mai
Buy It Now
Free Shipping Condition: New Location: 金东区, China The DRV8825 stepper motor driver carrier is the breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. DRV8825 has adjustable current ... morelimit, overcurrent and overheat protection, and six microstep resolutions (down to 1/32 step).
Buy It Now
$50.00 Shipping Condition: New Location: China Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM860A:(Nema34 stpper motor use this driver).
![]()
Buy It Now
Free Shipping Condition: New Location: United States 4 Axis CNC 3.5A TB6560 Stepper Motor Driver Board Controller F Engraving Machine. Click To Enlarge CNC stepper motor driver board 96560A V1 adopts the ... morenew chip TB6560AHQ of TOSHIBA. The max ouput current can reach to 3.5A, this driver board can drive the 2-phase or 4-phase stepper motor whose current is less than 3A. The advantages of the TB6560AHQ chip: The vibration of the motor is small and low noise: because of the 2/8/16 resolution can satisfy the different speed. Flush type low heat: The area of the chip can support itself to cool when the current is low Supports a lot of stepper motors The advantages in the high-speed running condition board might be made partly out of recycled parts. Because of the environmental protection Features: 4-wire 0-3.5A(normally 3A. The 3.5A is the peak current)can be regulated rate current output, bipolar stepper motor driver Standard parallel port. Supports Mach 2, KCAM 4 etc. Optical isolated(IO) and DCDC power isolated to protect the PC parallel port and other equipments Limit and emergency stop port( standard DB9 port) 4 working modes: mixed mode. Fast mode, slow mode, standard mode 4-resolution: 1 1/2 1/4 1/16 12-36V single power input uses the switch power chip as the 5V power supply. Stable and low heat Adopts RC + 7414 auto semi-flow The relay output can control the main axis 5th axis extension control port Packing list: 1* 4 Axis CNC TB6560 Stepper Motor Driver Board 1* DB25 Parallel Male- F emale Cable 4* Connect Terminal A997A NOTE We try our best to make every transaction perfectly, just for winning your F ive-Star rating. If you have any dissatisfaction. Please contact us. We will give you the most satisfactory results. PLEASE don't leave a neutral or negative easily. Shipping Item will be shipped within 24 hours on payment received from Hong Kong using Airmail. Only shipped to buyer's PayPal address. Please confirm with your PayPal address before you bid. Delivery time depends on destination and other factors. It may takes up to 30 business days. O
Buy It Now
Free Shipping Condition: New Location: China 1PC External Power Switching Motor Driver Adapter Module for MicrostepBoard Adapter Module External Power Switching Module for Microstep DriverFeatures:3D ... morePrinter Board External Large Motor Adapter Module, suitable for external currentEasy toMaterial: PlasticModule Size: 20x20x4mmCable length:50cm/19.68inchColor:BlackPackage includes: (Without retail package)1 External Power Switching Module * 1pc1 CablePackage includes: (Without retail package)Note: Please make sure the connecting direction is right.
Buy It Now
Free Shipping Condition: New Location: China Stepper Motor Driver is a board for DRV8825 microstepping bipolar stepper motor driver. - DRV8825 driver board is widely used in 3D printers and small ... moreCNC machines. 5 UEETEK DRV8825 Stepper Motor Driver Module 4-Layer with Mini Heat Sink for 3D Printer.
Buy It Now
Free Shipping Condition: New Location: China The DRV8825 stepper motor driver carrier is the breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. DRV8825 has adjustable current ... morelimit, overcurrent and overheat protection, and six microstep resolutions (down to 1/32 step).
Buy It Now
Free Shipping Condition: New Location: 金东区, China This driver is a DSP digital DM860H stepper motor driver. The subdivision is increased to 128 subdivisions, which is suitable for high subdivision applications. ... moreApplicable stepper motors: 57, 86 type 2-phase 4-phase (4 wires, 6 wires, 8 wires).
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China World Shipping. 7 Days Money Back. 5Axis Upgraded CNC Breakout Board Interface Set +Keypad +Display. Manual Control The Latest 3rd Generation Revolutionary ... more5 Axis Breakout Board Set( BCD-S) Make your microstep drivers powerful and outstanding I: PCB Instructions& Specifications Descriptions: The latest 3rd generation breakout board has been upgraded to the intelligent. Professional and industrial-level interface board set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation breakout board set has two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will make the breakout board control the microstep drivers more smoothly with lower noise. With the embedded intelligent memory chip. The professional version of this 3rd generation 5 Axis breakout board can easily record MAXIMUM 4 Axis’ X. Y, Z, A Axis) G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-code recordin
Buy It Now
Free Shipping Condition: New Location: China DM542 Stepper Motor Driver 2-Phase Digital Stepper Motor Driver for 57 86 Series. 3A T7128 128 High Subdivision Stepper Motor Driver THB7128 4257 Stepper ... moreDrives. B1206 Stepper Half Step Driver Two Phase Stepper Motor 120V Working Current 6A.
Buy It Now
$14.38 Shipping Condition: Seller refurbished Location: Long Beach, United States SERIAL NUMBER WILL VARY MANY AVAILABLE REMOVED FROM FUNCTIONING PANEL
Buy It Now
Free Shipping Condition: New Location: China Motor driver chip: HR8825. Standard for RaspberryPi 40PIN GPIO extension header, supports for RaspberryPi series boards. Integrates 5V regulator, allows ... moreproviding power for RaspberryPi.
Buy It Now
Free Shipping Condition: New Location: China Model: TB6600. It is an updated version of TB6600 4A stepper motor driver. Feature: 1. Original stepper motor driver chip, the current is selected by ... moreDIP switch. Item Type: Stepper Motor Driver. Powerful anti-high frequency interference ability, and overheating, overcurrent, short circuit protection.
Buy It Now
$72.00 Shipping Condition: New Location: China 3 Axis Driverbaord TB6560. Inductance: 3.5 mH/phase. 3 pcs Nema 23 stepper motor 270 oz.in,3A, 4 leads bioplar. Nema 23 stepper motor stepper motors. ... morewithout creep effect! • Adjustable drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different.
Buy It Now
$30.00 Shipping Condition: New Location: United States 4 x TB6560 MD430 single axis driver. TB6560 MD430 Low noise of stepper motor driver. MD430 is a compact single axis bipolar 3.0A/phase stepper motor microstepping ... moredriver with step and direction inputs, DIP switch settable step mode (full, half, eight and sixteenth--S3/S4), torque (100%, 75%, 50%, 20%--S5/S6) ,work current (0-3A--SW1/SW2/SW3) and decay mode (0%, 25%, 50% and 100%).
Buy It Now
Free Shipping Condition: New Location: China 1 PC Stepper Motor Driver DQ860HA with 7.8A/80VDC/256Microstep replacing DQ860MA. Stepper Motor Driver:DQ860HA. AC：24~80V DC:24~110V.
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States A4988 Is a complete microstepping motor driver, With built-in converter, Easy to operate. The product is available in the whole, half, 1/4.1/8 and 1/16. ... moreAs long as it is in" Stepping" Input a pulse in the input, Microstep can drive motor.
Buy It Now
$4.95 Shipping Condition: Used Location: Richardson, United States DRV8811 Evaluation Module. 38-V, 1.9-A bipolar stepper motor driver with current regulation and 1/8 microstepping. DRV8811EVM Evaluation Module. Vs (Max) ... more(V) 38. Number of full bridges 2.
Buy It Now
$115.00 Shipping Condition: New Location: China 3 pcs Nema 23 stepper motor 435 oz.in bipolar 23HS9442 Single shaft. Nema 23 stepper motor Stepper motor driver DM542A Hording torque when DM542A run ... moreunder high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: China (Excluded.).
Buy It Now
Free Shipping Condition: New Location: China Feature: 1. DMA860H is a low‑noise digital stepper motor driver with high efficiency. Item Type: Stepper Motor Driver. Motor Interface: A+ and A- are ... moreconnected to the positive and negative ends of the A-phase winding of the stepping motor; B+ and B- are connected to the positive and negative ends of the B-phase winding of the stepping motor.
Buy It Now
Free Shipping Condition: New Location: China DM556 Digital Stepper Motor Driver 2 Phase 5.6A for Nema23,34 Stepper Motor. DM542 Stepper Motor Driver 2-Phase Digital Stepper Motor Driver for 57 86 ... moreSeries. 3A T7128 128 High Subdivision Stepper Motor Driver THB7128 4257 Stepper Drives.
Buy It Now
$8.00 Shipping Condition: New Location: China 3P DM556S 24-50VDC 6A 256Microstep digital Stepper/Stepping motor Driver. 3 x DM556S Stepper Motor Driver. 【 Excellent Performance 】: DM556S Digital stepper ... moremotor driver, Using 32 -bit DSP technology, is suitable for driving 57 and 86 series motors, with excellent mid -speed and low -speed performance.
Buy It Now
$3.40 Shipping Condition: New Location: China The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder ... moreSJ2 closed on the EasyDriver). EasyDriver drives bi-polar motors, and motors wired as bi-polar.
Buy It Now
$2.99 Shipping Condition: New Location: China The A4988 is a DMOS microstepping driver with converter and overcurrent protection that operates bipolar stepper motors in full, half, 1/4, 1/8, and 1/16 ... morestepping modes, with output drive performance up to 35 V and ±2.
Buy It Now
Free Shipping Condition: Used Location: Boise, United States
Buy It Now
Free Shipping Condition: New Location: United States For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Box Professional ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States Self-Test: A push button is used on the GR214V to allow for quick in-the-field testing of the drive’s core functionality. If the onboard DIP switch is ... moreused to set phase current the user can adjust a trimpot for holding torque from 0% - 100% current in standby mode.
Buy It Now
$3.00 Shipping Condition: New Location: China The DM860A is a new generation of high performance digital stepper motor drivers. It can effectively reduce the noise and vibration during motor operation, ... moreand has the characteristics of low noise, low vibration and low temperature rise.
Buy It Now
Free Shipping Condition: New Location: 金东区, China This driver is a DSP digital DM860H stepper motor driver. The subdivision is increased to 128 subdivisions, which is suitable for high subdivision applications. ... moreApplicable stepper motors: 57, 86 type 2-phase 4-phase (4 wires, 6 wires, 8 wires).
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6560 Standard ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: China Model Number: 2DM860. Motor Type: Stepper Motor. 1 x Stepper Motor Driver. Users expect a small noise, high-speed device applications particularly good ... moreeffect. Pulse Frequency max :200K. Torque compensation in high speed.
Buy It Now
Free Shipping Condition: New Location: China It brings a unique level of system smoothness, providing optimum torque and nulls mid-range instability. Its unique features make the 3DM2283 an ideal ... moresolution for applications that require low-speed smoothness.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China TB6600 Stepper Motor Driver Controller 9-42VDC 4A Micro-Step for 57BYG250H Motor 1. Shipping list 1PC Stepper Drive TB6600 2. Specifications& Feature ... moreSignal input: single ended, pulse / direction Subdivision optional: 1/2/4/8/16/32 subdivision Output current: 0.5A-4.0A Input voltage: 9-42VDC (recommends 12-30V) The current is automatically halved at rest. Can drive 4, 6 and 8 Lead two-phase, four-phase stepper motor Optocoupler isolated signal input, strong anti-interference ability With overheating, overcurrent, undervoltage lockout, input voltage anti-reverse protection and other functions Small size, easy to install External signal 3.3-24V universal, no series resistor required Operating Temperature: -10 to 45 Degrees Celsius Storage temperature: -40 to 70 Degrees.
Buy It Now
Free Shipping Condition: New Location: Sterling Heights, United States The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 micro stepping bipolar stepper motor driver. The DRV8825 features adjustable ... morecurrent limiting, overcurrent and over temperature protection, and six micro step resolutions (down to 1/32-step).
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 3 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. 3 pcs Stepper motor driver, peak 7.8A 24-80VDC. Nema 34 stepper motor Hording torque ... morewhen DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$150.00 Shipping Condition: New Location: China 3PCS Nema34 Stepper Motor 34HS9840 with 1090oz-in holding torque, 4.0A,98mm. 3PCS Stepper Driver DM860A with 7.8A replacing MD882. Nema 34 stepper motor ... moreHolding torque: 1090 oz-in ( 7N. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. ).
Buy It Now
$36.00 Shipping Condition: New Location: China 2DM860 2phase NEMA23 NEMA34 stepper motor driver 32bit DSP DC30-80V 1.8-7.0A. JMC stepper driver 2DM860. 2DM860 driver greatly improves stability and ... morereduces noise under low subdivision. can drive two-phase 4,6,8 lines stepper motor.
Buy It Now
$0.89 Shipping Condition: New Location: China Can any 2.0A current 2-phase or 4-phase stepper motor. Motor noise optimization function. Output current:2.4A~7.2A,8 gears adjustable,Resolving power ... more0.5A. insulation resistance: Normal pressure and temperature >500M.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 3 pcs Nema 23 stepper motor 270 oz.in,3A, 4 leads bioplar. Nema 23 stepper motor without creep effect! • Driver output compatible with 2 or4 phase, 4,6 ... moreor 8 lead stepper motors, 3A max. stepper motors.
Buy It Now
Free Shipping Condition: New Location: 中原区, China The DRV8825 features adjustable current limiting, over current and over temperature protection, and six microstep resolutions (down to 1/32 step). 5 x ... moreDRV8825 Stepper Motor Driver. Module Size, Pinout Interface Match Those Of The A4988 Stepper Driver Carriers In Most Respects.
Buy It Now
$17.43 Shipping Condition: New Location: Canada
Buy It Now
$3.00 Shipping Condition: New Location: China It is suitable for driving 2-phase and 4-phase hybrid stepping motors. - 1 x Stepper Motor Driver. - Output current up to 7.2A. - Good high speed performance. ... more- Suitable for 2-phase and 4-phase motors.
Buy It Now
$30.00 Shipping Condition: New Location: United States CW5045 high microstep stepper motor driver. 4 x23HS2430B Nema23 stepper motor (Dual Shaft) 112mm,425oz-in,2.8N.m,3.0A. 4 xCW5045 stepper motor driver ... more24-50V,4.5A,256microstep. 1 x5 Axis breakout board V5 type.
Buy It Now
$3.00 Shipping Condition: New Location: China Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. - 1 x DM542A stepping motor driver.
Buy It Now
$2.99 Shipping Condition: New Location: China Description This module is blue PCB now.Please know it. The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping ... morebipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting. Overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) 1）Simple step and direction control interface 2）Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 3）Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 4）45 V maximum supply voltage 5）Built-in regulator(no external logic voltage supply needed) 6）Can interface directly with 3.3 V and 5 V systems 7）Over-temperature thermal shutdown. Over-current shutdown, and under-voltage lockout 8）Short-to-ground and shorted-load protection 9）4-layer. 2 oz copper PCB for improved heat dissipation 10）Exposed solderable ground pad below the driver IC on the bottom of the PCB 11）Module size. Pinout, and interface match those of our A4988 stepper motor driver carriers in most respects(see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet(1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil(see the Power Dissipation Considerations section below for more information) Here are some of the driver’s key
Buy It Now
$6.95 Shipping Condition: New Location: Hoffman Estates, United States Pulse input frequency up to 200 KHz. Its unique features make theKL-4042D an ideal solution for applications that require low-speed smoothness. It can ... morebe used invarious kinds of machines, such as laser cutters, laser markers, high precision X-Y tables, labelingmachines, and so on.
Buy It Now
$3.40 Shipping Condition: New Location: China Description This module is blue PCB now.Please know it. The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping ... morebipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board. So it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting. Overcurrent and overtemperature protection, and six microstep resolutions(down to 1/32-step) It operates from 8.2– 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow(rated for up to 2.2 A per coil with sufficient additional cooling) 1）Simple step and direction control interface 2）Six different step resolutions: full-step. Half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 3）Adjustable current control lets you set the maximum current output with a potentiometer. Which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates 4）45 V maximum supply voltage 5）Built-in regulator(no external logic voltage supply needed) 6）Can interface directly with 3.3 V and 5 V systems 7）Over-temperature thermal shutdown. Over-current shutdown, and under-voltage lockout 8）Short-to-ground and shorted-load protection 9）4-layer. 2 oz copper PCB for improved heat dissipation 10）Exposed solderable ground pad below the driver IC on the bottom of the PCB 11）Module size. Pinout, and interface match those of our A4988 stepper motor driver carriers in most respects(see the bottom of this page for more information) This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet(1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil(see the Power Dissipation Considerations section below for more information) Here are some of the driver’s key
Buy It Now
$1.63 Shipping Condition: New Location: China Applicable stepper motor: 42.57, 86 Phase type phase (4 wire 6 wire 8 wire line). the maximum output current of 4.0A eight optional;. standard common ... moreanode single pulse interface;. Color: See pictures.
Buy It Now
Free Shipping Condition: New Location: United States DIY CNC Kit 3 Axis With CNC Breakout Board + Cables + TB6600HG Stepper Drivers + 3 Pieces TB6600HG Stepper Driver Board Controller The latest upgraded ... moresalable 5 axis breakout board is specially designed for the CNC single axis stepper driver controller. Such as TB6600HG, M542, M542H, MA560, MA860H, 2M542, 2M982 etc single axis stepper driver controller. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover. The brand new design with BiCD0.13(45V) process technology on the chipset also ensures maximum 5.0A output current and 45V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps. All the 2 Phase or 4 Phase of Nema17. Nema23, Nema24 and Small-sized Nema34 stepper motors will work perfectly with this new-type TB6600HG Stepper Driver. Click here for In short. With this CNC Kit, you will get more benefits from the Kit on CNC work. Please purchase this kit with confidence. High performance. Cost-effective. Maximum support 5-axis stepper motor driver controller. Two types of ways to get power. 5V DC power supply or USB port to directly get power from PC. Two-stage signal processing. Smooth signal transmission, powerful anti-jamming. 5-input interface to define the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc. Relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. 5-axis work LED display. Visually display the working condition of the stepper driver controller. High performance. Cost-effective. Automatic idle-current reduction. Supply voltage up to 45V DC. Output current up to 5.0A. Suitable for 2-phase and 4-phase motors. High speed optoelectronic iso
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 3 Axis TB6560 CNC Stepper Motor Driver Board 1.5A-3A*NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller Product Features: Toshiba TB6560AHQ chip- High ... morepower. Maximum 3.5A drive current chipset! 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step, Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors*Attention: This driver is 1.5A-3A version. Which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A. If the rated current your stepper motors is below 1.5A. You can choose the 0.5A-2.5A version. Please let us know which version(1.5A-3A version is default) you need immediately after placing an order. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Deta
Buy It Now
Free Shipping Condition: New Location: United States 3 Axis TB6560 CNC Stepper Motor Driver Board 1.5A-3A*NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller Product Features: Toshiba TB6560AHQ chip- High ... morepower. Maximum 3.5A drive current chipset! 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step, Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors*Attention: This driver is 1.5A-3A version. Which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A. If the rated current your stepper motors is below 1.5A. You can choose the 0.5A-2.5A version. Please let us know which version(1.5A-3A version is default) you need immediately after placing an order. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Deta
Buy It Now
Free Shipping Condition: New Location: China Stepper Driver. Hybrid Stepper Motor. Stepper Motor Driver. Linear Stepper Motor. Geared Stepper Motor. Closed Loop Stepper Motors. Nema 06 (14 x 14). ... moreNema 08 (20 x 20).
Buy It Now
$20.00 Shipping Condition: New Location: Sacramento, United States The G213V is Geckodrive's toughest drive with a step pulse multiplier, allowing it to run in full step, half step, 5 microstep and 10 microstep modes. ... morePower-on reset. Full step, half step, 5 microstep and 10 microstep selectable resolution.
Buy It Now
Free Shipping Condition: New Location: Brentwood, United States The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step).
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China High Integrated 4Axis CNC TB6600 Stepping Driver Nema23/Nema24/Nema34 0.2-5A Box The Latest 3rd Generation Revolutionary TB6600HG 4 Axis Stepper Driver ... moreBox Set( TB4H-CD-S(Box) I: PCB Instructions& Specifications Descriptions: Comparing with the previous 3rd generation TB6560AHQ Stepper Driver. Besides including all the functions that the 3rd generation TB6560AHQ Stepper Driver has, this newly released 3rd generation TB6600HG Stepper Driver was specially developed for bigger stepper motors which have higher current. As long as the current range of the stepper motors is within 0.2-5.0 amps. All the 2 Phase or 4 Phase of Nema17, Nema23, Nema24 and Nema34 stepper motors will work perfectly with this new TB6600HG Stepper Driver. Actually. The 3rd generation TB6600HG Stepper Drivers have two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will avoid the TB6600HG chip on the board being easily blown as the previous version. With the embedded intelligent memory chip. The professional version of this 3rd generation 4 Axis TB6600HG Stepper Driver can easily record the G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Standard ... moreDriver Board is equipped with TB6560AHQ chip.
|
|
|
 |