|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: New Location: Chino, United States And your motor power should not be more than TWICE the power of this VFD. Suitable Motor Power: 1.5KW, Horsepower: 2HP. Rated Current: 7A. DC Cooling ... moreFan: The variable frequency drive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Suitable Motor Power: 2.2KW, Horsepower: 3HP. And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: The variable frequency ... moredrive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Package Included 1* Variable Frequency Drive 1* English Manual Notes Please avoid using the inverter in an environment where there is humidity, water ... moremist, and metal debris falling, it may cause a short circuit. And your motor power should not be more than TWICE the power of this VFD. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Package Included 1* Variable Frequency Drive 1* English Manual Notes Please avoid using the inverter in an environment where there is humidity, water ... moremist, and metal debris falling, it may cause a short circuit. And your motor power should not be more than TWICE the power of this VFD. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Package Included 1* Variable Frequency Drive 1* English Manual Notes Please avoid using the inverter in an environment where there is humidity, water ... moremist, and metal debris falling, it may cause a short circuit. And your motor power should not be more than TWICE the power of this VFD. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Model: YL568K. Suitable Motor Power: 0.75KW, Horsepower: 1HP. And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: ... moreThe variable frequency drive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Specification Model: YL568K Application Range: Universal Color: Black Material: ABS Input Voltage: 220V Output Voltage: 220V Rated Current: 10A Suitable ... moreMotor Power: 2.2KW, Horsepower: 3HP Power Supply Phase: Single Phase Output Phase: 3 Phase DC Power Supply: Voltage Type Gross Weight: 1.2kg/2.7lbs Net Weight: 1kg/2.2lbs Product Size:11*8.5*14.5cm/4.33*3.3*5.71in Package Size: 16.5*20*12.5cm/6.5*7.97*4.92in Package Included 1* Variable Frequency Drive 1* English Manual.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Package Included 1* Variable Frequency Drive 1* English Manual Notes Please avoid using the inverter in an environment where there is humidity, water ... moremist, and metal debris falling, it may cause a short circuit. And your motor power should not be more than TWICE the power of this VFD. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Package Included 1* Variable Frequency Drive 1* English Manual Notes Please avoid using the inverter in an environment where there is humidity, water ... moremist, and metal debris falling, it may cause a short circuit. And your motor power should not be more than TWICE the power of this VFD. Please read the operating manual completely before use. And pay particular attention to the safety instructions included. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Buy It Now
$5.00 Shipping Condition: New Location: Chino, United States And your motor power should not be more than TWICE the power of this VFD. Rated Current: 7A. DC Cooling Fan: The variable frequency drive is equipped ... morewith a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Chino, United States And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: The variable frequency drive is equipped with a fan to improve ... morethe stability of the inverter. The fan runs automatically when the temperature rises and switches off when the temperature stabilizes.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Suitable Motor Power: 2.2KW, Horsepower: 3HP. And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: The variable frequency ... moredrive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6560 Set Standard ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Box Standard ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China New CNC Standard 4Axis TB6560 Stepper Driver Full Kit + Motor/PSU/Keypad/Display The Latest 3rd Generation Revolutionary& Standard TB6560 4 Axis Stepper ... moreDriver Set( TB4CD-S) +4x Nema23 1.86Nm/263 Oz-in 57BYGH78-401A Stepper Motors +1x 360W 24V15A Switching Power Supply I: PCB Instructions& Specifications Descriptions: The latest 3rd generation TB6560 Stepper Driver has been upgraded to the intelligent. Professional and industrial-level drive set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation TB6560 Stepper Drivers have two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will avoid the TB6560 chip on the board being easily blown as the previous version. With the embedded intelligent memory chip. The professional version of this 3rd generation 4 Axis TB6560 Stepper Driver can easily record the G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-code recording
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Box Professional ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6560 Box Professional ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Set Standard ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. ™ 4 Axis TB6600 Box Professional ... moreDriver Board Kit for CNC DIY. This4 Axis TB6600 Box Professional Driver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6560 Standard ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Standard ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
$62.00 Shipping Condition: New Location: China 1 pc Nema 23 stepper motor with 425 oz.in, 3A,4 leads 23HS9430. Part No.: 23HS9430. Hording torque when DM542A run under high speed is also significantly ... morehigher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Chino, United States And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: The variable frequency drive is equipped with a fan to improve ... morethe stability of the inverter. The fan runs automatically when the temperature rises and switches off when the temperature stabilizes.
$159.00 Shipping Condition: New Location: Hong Kong SAR China (Cnc Mill 3 axis NEMA34 MOTOR 30kg. 3x NEMA34 2ph 30kg. cm Step Motor. cm) step motor Running at 3000rpm. IDEAL FOR CNC PARALLEL PORT SOFTWARE. 1x PARALLEL ... morePORT CABLE. 1x CNC SOFTWARE BREAKOUT BOARD.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Standard ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Upgraded Revolutionary CNC Stepper Driver Box Kit. 4x Nema23 Motor 300 Oz-in,PSU The Latest 3rd Generation Revolutionary& Professional TB6560 4 Axis ... moreStepper Driver Box Set( TB4CD-P(Box) +4x Nema23 2.1Nm/300 Oz-in GB23H282-30-4A Stepper Motors +1x 360W 24V15A Switching Power Supply I: PCB Instructions& Specifications Descriptions: The latest 3rd generation TB6560 Stepper Driver has been upgraded to the intelligent. Professional and industrial-level drive set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation TB6560 Stepper Drivers have two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will avoid the TB6560 chip on the board being easily blown as the previous version. With the embedded intelligent memory chip. The professional version of this 3rd generation 4 Axis TB6560 Stepper Driver can easily record the G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-
Buy It Now
$70.00 Shipping Condition: Used Location: China Sales Policy. It is very important, we need it. You should receive item within 2-4 weeks.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Suitable Motor Power: 2.2KW, Horsepower: 3HP. And your motor power should not be more than TWICE the power of this VFD. DC Cooling Fan: The variable frequency ... moredrive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China QUALITY-GADGETS eBay Item! Latest 3rd Generation Breakout Board. Gcode Recoded, Manual Programming Function Descriptions I. About the 3rd Generation Breakout ... moreBoard Set This breakout board has been upgraded to an intelligent and industrial-level interface board set. The redesigned PCB board enables smoother control of microstep drivers and stepper motors with lower noise. It has high compatibility with all the 2-phase. 3-phase and 4-phase microstep drivers and stepper motors. The equipped manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This breakout board can easily record MAXIMUM 4 axis' X.Y,Z,A axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can control the microstep drivers and stepper motors via using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) not only can be used for manual motor control. But also for manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you also can easily control the microstep drivers and stepper motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 5 Axis Professional Version(BCD-P) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions Features High performance.
Buy It Now
$189.00 Shipping Condition: New Location: China 4PCS Nema34 Stepper Motor 34HS9456 with 965oz-in holding torque, 5.6A,98mm,4 leads. Inductance: 4.1 mH/phase. 4PCS Stepper Driver DM860A with 7.8A. Nema ... more34 stepper motor Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA342-7842S4 Nema34 Stepper Motor. This function is widely applied in RBI machine, Conveyor etc. Stepper motors and drivers from ENGMATE. Compared to ... morestandard version, professional version mainly has two more functions.
Buy It Now
Free Shipping Condition: New Location: Chino, United States And your motor power should not be more than TWICE the power of this VFD. Suitable Motor Power: 1.5KW, Horsepower: 2HP. DC Cooling Fan: The variable frequency ... moredrive is equipped with a fan to improve the stability of the inverter.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The M335 is a high performance microstepping driver with low price. The M335 adopts single-chip PWM bipolar sinusoidal chopper to ensure low vibration ... moreand high efficiency. It is suitable for driving 2-phase and 4-phase hybrid stepping motors, so the Nema16, Nema17, Nema23 stepper motors with a 0.5A-3.5A current will be suitable.
Buy It Now
Free Shipping Condition: New Location: China Maximum pulse output frequency: 50KHz (four axes can be 50KHZ simultaneously). Free choice of input function: limited input can achieve a variety of user ... moreneeds. Driver board MACH3 engraving machine 5 Axis CNC breakout board optical coupler.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China CNC Kit 3 Axis TB6560 Driver Board +3x Nema 17 Stepper Motor 60 Oz-in + Software You are watching a GREAT VALUE 3 AIXS CNC PC CONTROL COMPLETE KIT! Package ... moreincludes: 1 x New 3 Axis TB6560 Driver Controller Board 1/16Microstep. 12-36V, 1.5A-3A 3 x New 42BYGH47-401A Single-Shaft Stepper Motors 0.44 Nm/62 Oz-in/1.68A 1 x New 12V 10A power supply Product Features: Toshiba TB6560AHQ chip- High power. Maximum 3.5A drive current chipset. 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step. Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Details: Power supply DC 12-36V*This stepper motor directly gets the power from the stepper driving controller board. It doesn't require a separate power source. Volta
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6560 Box Professional ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: China For NEMA17 Stepper Mounting Plate Suitable for NEMA 17 Stepper Linear-3D Printer. DM542 Stepper Motor Driver For 57 86 Series 2-phase Digital Stepper ... moreMotor Driver. DM860H Digital Stepper Motor Driver 5.6A for 57 86 Stepper Motor NEMA23 34.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 1 5 Axis Professional Breakout Board + 3 EMA2-080A72 Microstep Motor Drivers. 5 Axis Professional Breakout Board. • Compatible with all the 2 phase, 3 ... morephase and 4 phase microstep drivers in the market.
Buy It Now
Free Shipping Condition: New Location: China Connector: USB. If you do not receive our reply within 48 hours, pls. If you are satisfied with our service, pls.
Buy It Now
$3.99 Shipping Condition: New Location: China ER11 collect: 3.175mm. - 1 400Wspindle motor with with ER11 3.175 collet. - Axis collet Length: 43mm. motor run clockwise when F/R is connecting +5V,otherwise ... moremotor will reverse. Motor is running When EN is floating.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China New 4axis CNC Stepping Driver TB6600HG Set. LCD Display Handle Controller 0.2-5A Description I. About the 3rd Generation TB6600HG Stepper Controller Set ... moreThis TB6600HG Stepper Controller Set has all the functions of TB6560AHQ Stepper Controller Set. And is specially developed for stepper motors with higher currents. All the 2 or 4 phase Nema17/23/24/34 stepper motors with current range of 0.2A~5.0A work perfectly with this TB6600HG Set. It has standard version and professional version to meet different user needs. For further information. Please click on the following links. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 4 Axis' X.Y,Z,A Axis) G-code running i n the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. on the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 4 Axis Professional Version(TB4H-CD-P) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& Control Panel Features High performance. Cost-effective; Manual motor control via control panel; support tool-settings on X.
Buy It Now
$76.00 Shipping Condition: New Location: China 1PCS Stepper Driver DM860A with 7.8A. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s ... moremore, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China World Shipping. 7 Days Money Back. 3 Axis CNC Router TB6560 Stepper Driver + Display + Control Pad + Aluminium Box Descriptions I. About the 3rd Generation ... moreTB6560 Stepper Controller Box This stepper controller box has been upgraded to an intelligent and industrial-level driver board set. The redesigned PCB board enables smoother control of motors. The totally enclosed optical isolation and bipolar constant-current chopper ensure a low noise& low vibration operation environment. Helping to avoid creeping at a low speed. Internally built manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& C
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip ... morePWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
Buy It Now
Free Shipping Condition: New Location: China The switching frequency is high, up to 60KIIZ, which effectively avoids the unpleasantness caused by the low frequency of debugging the motor. This module ... morecan be used for the general high-power DC motor drive, the maximum current can reach 100A, stable performance, is the general integrated motor drive can not be matched, therefore, very suitable for robot competition, tank competition and so on.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China QUALITY-GADGETS eBay Item! 3 Axis CNC Stepper Motor Driver TB6560 Box Set + LCD Display + Handle Controller Descriptions I. About the 3rd Generation TB6560 ... moreStepper Controller Box This stepper controller box has been upgraded to an intelligent and industrial-level driver board set. The redesigned PCB board enables smoother control of motors. The totally enclosed optical isolation and bipolar constant-current chopper ensure a low noise& low vibration operation environment. Helping to avoid creeping at a low speed. Internally built manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& Contr
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 4 Axis Upgraded CNC TB6560 Stepper Driver Set +Keypad +Display. Manual Control The Latest 3rd Generation Standard TB6560 4 Axis Stepper Driver Set( TB4CD-S) ... moreI: PCB Instructions& Specifications Descriptions: The latest 3rd generation TB6560 Stepper Driver has been upgraded to the intelligent. Professional and industrial-level drive set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation TB6560 Stepper Drivers have two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will avoid the TB6560 chip on the board being easily blown as the previous version. With the embedded intelligent memory chip. The professional version of this 3rd generation 4 Axis TB6560 Stepper Driver can easily record the G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-code recording function is enough for all the three axis working without computer, to avoid repeated function, the manual progra
Buy It Now
$3.00 Shipping Condition: New Location: China It could work under Mach4 software. The maximum step-pulse frequency is 2000 KHz. Now MK6-M4 is stronger, more stable and better performance than other ... moreversion. Support all versions of Mach4. Under Mach4 working state, USB cable unplugs and then plugs in, but also the normal connection.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Of the computer, and thenrerun the recorded G-code to make the stepper motor work without the computer any more. This function is widely used on working ... morewhich just need one Axis, such as RBI machine, Conveyor etc.
Buy It Now
$16.90 Shipping Condition: New Location: Hong Kong SAR China NEW 2 phase Mirco stepper motor Driver High performance 5.6A 50V Industrial Grade Bipolar( A+. A- B+, B- stepping driver, Capable to drive up to 50V@ ... more5.6A Per phase Features Patented technology INDUSTRIAL GRADE for LONG TIME OPERATION Mirco step form 400 to 128000 step per Revelution High-speed torque Supply voltage up to DC24~50V current output up to 5.6A peak Optically isolated input signals, pulse frequency up to 100 KHz Automatic idle-current reduction State current control for less motor heating Suitable for 4.6,8 lead motors DIP switch current setting with 8 different value 1.4. 2.1, 2.7, 3.2, 3.8, 4.3, 4.9, 5.6A Over Voltage.Coil to Coil& Coil to Ground short circuit protection IDEA for NEMA 23& NEMA 34 stepper Motor Size: 120x90x36mm Weight: 300g Input Signal: 1: PLUSE(step pulse/Rising Edge) 2: DIR( direction) 3: ENA(enable) Combine shipping available The first is US$16.9 the another is US$9 per each Will send by register mail. Normally takes 7-10 days You can buy controller BOARD here You can buy Power Supply Here http:stores.shop.ebay.com.au/Easycnc_W0QQ_armrsZ1 You can buy motor here http:stores.shop.ebay.com.au/Easycnc_W0QQ_armrsZ1 Control by Mach3. Drive NEMA34 800oz.in motor turning at 3000rpm YOU CAN BUY CPU& CNC PARTS HERE THANK YOU
Buy It Now
Free Shipping Condition: New Location: Denver, United States Adopting user-friendly keyboard design, reasonable layout, intuitive and clear.
Buy It Now
Free Shipping Condition: New Location: China It could work under Mach4 software. The maximum step-pulse frequency is 2000 KHz. Now MK6-M4 is stronger, more stable and better performance than other ... moreversion. Support all versions of Mach4. Under Mach4 working state, USB cable unplugs and then plugs in, but also the normal connection.
Buy It Now
$189.00 Shipping Condition: New Location: China 4 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. Hording torque when DM860A run under high speed is also significantly higher than the ... moreother two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China This function is widely applied in RBI machine, Conveyor etc. EMA232-7630S4 Nema23 Stepper Motor. Stepper motors and drivers from ENGMATE. ™ 4 Axis Kit ... morefor CNC DIY. 5 Axis Professional Breakout Board.
Buy It Now
$23.75 Shipping Condition: New Location: Hoffman Estates, United States 3pcs NEMA23 570 oz/in 3.5A 1/4” Dual Shaft Stepper Motor. Mach3 set up for kit and machine, Download here. Mach3Tutorial (193486). Mach3setup (12954). ... moreMach3 Setup (Mach3Mill.xml file) (9226). KL-4030WithC10 (11913).
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Set Professional ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This4 Axis TB6600 Standard ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China CNC Standard 4Axis TB6560 Stepper Driver Set + Nema 23 Motor + PSU More Smoothly The Latest 3rd Generation Revolutionary& Standard TB6560 4 Axis Stepper ... moreDriver Set( TB4CD-S) +4x Nema23 1.24Nm/175 Oz-in 57BYGH56-401A Stepper Motors +1x 360W 24V15A Switching Power Supply I: PCB Instructions& Specifications Descriptions: The latest 3rd generation TB6560 Stepper Driver has been upgraded to the intelligent. Professional and industrial-level drive set by re-designing the PCB board. Embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) Actually. The 3rd generation TB6560 Stepper Drivers have two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the“ computer G-code recording function” And another is the“ manual programing function” Except these two functions. These two types of versions have no other differences. Firstly. Both of these two types of versions have upgraded their PCB boards, the re-designing the PCB board will avoid the TB6560 chip on the board being easily blown as the previous version. With the embedded intelligent memory chip. The professional version of this 3rd generation 4 Axis TB6560 Stepper Driver can easily record the G-code running on the CNC software(e.g. Mach3. EMC2. KCAM4. Etc. of the computer, and then rerun the recorded G-code to make the stepper motor work without the computer any more. Furthermore. The upgraded external manual control tools(display panel and control pad) on the professional version can be not only used for manually controlling the stepper motor, but also manually programming the G-code. All the manually Programmed G-code will also be recorded in to the embedded intelligent memory chip. And then we also can easily run the recorded G-code to control the stepper motor. Considering that the computer G-code recording
Buy It Now
$70.00 Shipping Condition: Used Location: China Sales Policy. It is very important, we need it. You should receive item within 2-4 weeks.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Box Professional ... moreDriver Board is equipped with TB6600HG chip.
|
|
|
 |