|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
$227.00 Shipping Condition: New Location: China 3 pc Nema 42 stepper motor 4120 oz.in, 8.0A, 4 leads, bipolar,Dual Shaft 42HS6480B. Stepper motor driver: DM2722A. Nema 42 stepper motor. Stepper driver ... moreworking current is set by DIP-1 switches. l Drive current is adjustable in 16 channels from 1.2A/phase to 7.0A/phase.
Buy It Now
$139.00 Shipping Condition: New Location: Hong Kong SAR China 2x NEMA34 2 phase 4.5N.m Step Motor. IDEAL FOR CNC PARALLEL PORT SOFTWARE. From 200 or 12800 Pulse per Turn. 2x 5.6A Micro step INDUSTRIAL GRADE DRIVE. ... more1x PARALLEL PORT CABLE. 1x CNC SOFTWARE BREAKOUT BOARD.
Buy It Now
$78.00 Shipping Condition: New Location: China 1 pc Nema 34 stepper motor 1700 oz.in bipolar with single Shaft. 1 pc Breakout Board & 1 pc parallel cable 1. Stepper motor. Hording torque when DM860A ... morerun under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: China 3-36V 10A Peak 30A Dual Motor Driver Module board H-bridge DC MOSFET IRF3205 Description: The drive performance of these non-L298 motor driver chip can ... morebe compared. The driver focus on current and efficiency, effectively motor power and battery life. Can withstand high current overload, the maximum current up to 30A. This drive also has a brake function can be quickly stopped the motor. Brake quickly, braking obvious, easy to implement this feature The drive uses the full two half-bridge driver chip + low resistance N-channel MOSFET components. Complete two half-bridge driver chip reliable drive mode. The MOSFET switching losses to a minimum. Improve power utilization. MOSFET driver chip comes with hardware brake function and power feedback. This drive is superior integrated low power chip solution and the other half-bridge power margin in the coordinated combination of programs and complex issues and complementary drive problems N-channel MOSFET IRF3205 MOSFET. Use two dedicated half-bridge driver chip on the top tube using the bootstrap capacitor, so that the tube has enough drive voltage of the MOSFET channel can be opened quickly, improve motor acceleration curvature, but also quickly for the motor brake. This allows the trolley can quickly start can quickly kill the car. The driver can operate at 0% 99% of the duty cycle of the PWM modulation. The motor driving voltage can be obtained sufficiently. Features Motor forward: DIR = 1 PWM = PWM Motor reversal: DIR = 0 PWM = PWM Parking brake: DIR = X PWM = 0(X is an arbitrary state) Motor and power connections POWER connected to the positive power supply. GND power supply is negative. Two motors were connected MOTOR1, MOTOR2 Product performance parameters: Rated voltage: 3v-36v(can be customized according to the user) Rated Current: 10A Peak current: 30A Use: Freescale smart car contest Undergraduate Electronic Design Contest variety of DC motor control circuit Dimensions: length 108mm. Width 58mm Package 1pc 3-36V 10A Peak 30A Dual Motor Driver Module board
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. 4 pcs Stepper motor driver DM542A, 24-50VDC.
Buy It Now
Free Shipping Condition: New Location: China Dual motor interface, each rated output current 7A, peak current 50A, the motor interface must not short-circuit, the proposed series 10A fuse. For NEMA17 ... moreStepper Mounting Plate Suitable for NEMA 17 Stepper Linear-3D Printer.
Buy It Now
$110.00 Shipping Condition: New Location: China 4 pcs Nema 23 stepper motor 425 oz.in bipolar 23HS9430B Dual shaft. Nema 23 stepper motor Hording torque when DM542A run under high speed is also significantly ... morehigher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$89.00 Shipping Condition: New Location: China 1.3PCS Nema34HS1456B stepper motor 1232oz. in=8.4N.m 5.6A 116mm,4leads ,dual shaft. in=8.4N.m 5.6A 116mm,4leads ,Dual shaft. 2.3PCS Stepper motor driver ... moreHigh Perfermance Stepper Driver DM860A Up to7.8A, 24-80VDC.
Buy It Now
$189.00 Shipping Condition: New Location: China 4 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. Hording torque when DM860A run under high speed is also significantly higher than the ... moreother two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$2.29 Shipping Condition: New Location: China Stepper Motor Driver Current Adjustable 32 Subdivision 160W Optocoupler Isolation Interface Motor Drive for 42/57 Stepper Motor. Subdivision: 1-32 subdivision. ... moreTMC2209 V1.2 Stepper Motor Driver DC 4.75-28V 2A 3D Printer Parts for BTT SKR.
Buy It Now
$110.00 Shipping Condition: New Location: China 4 pcs Nema 23 stepper motor 435 oz.in bipolar 4.2A 23HS9442. Nema 23 stepper motor Stepper motor driver DM542A Hording torque when DM542A run under high ... morespeed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$230.00 Shipping Condition: New Location: China 1.1PC Nema34HS5435C-37B2 stepper motor 1600oz. in=10.5N.m 3.5A 151mm ,single shaft. 1 PC Nema34HS5435C-37B2 stepper motor 1600oz. in=10.5N.m 3.5A 151mm. ... more2.1 pc Stepper motor driver High Perfermance Stepper Driver DM860A Up to7.8A, 24-80VDC.
Buy It Now
$230.00 Shipping Condition: New Location: China Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. 4 PCS Nema 23 stepper motor 270 oz.in single SHAFT.
Buy It Now
$89.00 Shipping Condition: New Location: Denmark 3 pcs Nema 23 stepper motor 435 oz.in bipolar 23HS9442. Nema 23 stepper motor. Hording torque when DM542A run under high speed is also significantly higher ... morethan the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$72.00 Shipping Condition: New Location: China 1.1PCS Nema34HST9805-02B2 stepper motor 878oz. in=7.0N.m 2A 98mm ,dual shaft. 1.Nema34HST9805-02B2 stepper motor 878oz. in=7.0N.m 2A 98mm. 2.1PCS Stepper ... moremotor driver High Perfermance Stepper Driver DM860A Up to7.8A, 24-80VDC.
Buy It Now
$3.00 Shipping Condition: New Location: China It is the new 3-axis Mach3 motion card. - 1 x Mach3 Motion Card. Download the latest version of Mach3 - Axis Backlash: YES. - Axis output number: 4 Axis ... more(high-speed optocouplers). - Slave Axis(Dual X/Y/Z): NO.
Buy It Now
$89.00 Shipping Condition: New Location: Denmark 1 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. 1 pcs Stepper motor driver, peak 7.8A 24-80VDC. Nema 34 stepper motor Hording torque ... morewhen DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$3.00 Shipping Condition: New Location: China It could work under Mach4 software. The maximum step-pulse frequency is 2000 KHz. Now MK3-M4 is stronger, more stable and better performance than other ... moreversion. Support all versions of Mach4. Under Mach4 working state, USB cable unplugs and then plugs in, but also the normal connection.
Buy It Now
$3.00 Shipping Condition: New Location: China New Wireless MPG Pendant Handwheel Mach3 For CNC Mac.Mach 3. 4 axis Controller Click Photos to Enlarge Click to Enlarge Description The RF is Standard ... morewith 2.4G ISM.The Tx power is 0DB and the RX sensitivity is-98DB. The RF has 64 channels.The channel gap is 1Mhz. The protocol Designed with high performance; Low power consumption;Automatic learning ID Number. To jump frequency Adaptively when noised.Which can work with 2.4G wireless Mic,Wlan and Bluetooth etc. devices. has the function of the hand wheel. 100PPR the manual pulse generator output. Display. Real-time display of the machine the workpiece coordinates, mechanical coordinates. Coordinates X. Y, and Z three-axis with the screen display. Before using the hand wheel. Install the driver file, mode of operation is as follows: 2. XHC-ShuttlePro Installation. 2.1:When Mach3 is installed. There will be a folder created named“PlugIns” in the Mach3 folder. This folder is the location to put and Plugin files that you want Mach3 to know about. Place. XHC-ShuttlePro.dll” in the\Mach3\PlugIns folder. Check and make sure it is there. Setup diver for Probe Z surface function;M930.m1s copy the installation directory to the. MACH3.Mach3\macros\Mach3Mill. 2.2:Now that the XHC-ShuttlePro.dll file is in\Mach3\PlugIns. The next step is to connect the. HuttlePro. If you are certain that your ShuttlePro is working and your hardware is working thenyou can simply plug in the ShuttlePro to one of the USB ports. 2.3:Once the ShuttlePro is connected. Start Mach3 and go to the“Config” menu choice and select. ConfigPlugins” You should see the ShuttlePro choice with a green checkmark in front of it. If it. Is not checked. You can check it. The checkmark means that Mach3 found the ShuttlePro on. Tartup. Click the“CONFIG” in yellow and set the buttons as you wish. 2.4:Once you have the proper button selected in the Mach3 ShuttlePro Plugin CONFIG menu, Your Shuttle device should be working properly. Package included: 1x Wireless USB Receiver. 1x CNC Wireless Remote Ha
Buy It Now
$76.00 Shipping Condition: New Location: China 1PCS Stepper Driver DM860A with 7.8A. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s ... moremore, the positioning accuracy is also higher.
Buy It Now
$57.00 Shipping Condition: New Location: China 1pc Nema 34 stepper motor 1232 oz.in bipolar,Dual Shaft 34HS1456B. Hording torque when DM860A run under high speed is also significantly higher than the ... moreother two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$5.00 Shipping Condition: New Location: China MK4-V: 4 axis motion card works with Mach3 CNC system for all windows platform. Mach3 Port Position: P1 Port. - Fully support all Mach3 version. - 16 ... moregeneral-purpose input, 8 output has speed function, the spindle actual speed Mach3.
Buy It Now
$89.00 Shipping Condition: New Location: Denmark 4PCS Nema34 Stepper Motor 34HST9805-37B2 with 878oz-in holding torque, 2.0A,98mm. 4PCS Stepper Driver DM860A with 7.8A replacing MD882. Hording torque ... morewhen DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$78.00 Shipping Condition: New Location: China Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. 1 pc Nema 23 stepper motor with 425 oz.in.
Buy It Now
$3.00 Shipping Condition: New Location: China Added parsing error prompt, DDCS V3.1 has not been there, and it will stop directly if there is parsing error. It also supports the universal FANUC compatible ... moreG instruction set. - 1 x Handwheel DDPMG.
Buy It Now
Free Shipping Condition: New Location: China TMC2209 V1.2 Stepper Motor Driver DC 4.75-28V 2A 3D Printer Parts for BTT SKR V1.4 SKR Mini E3 SKR 2 Ender3 V2 Voron 2.4. TMC2209 has a continuous driving ... morecurrent of 2A and a peak current of 2.8A, which is 0.6A- 0.8A higher than that of TMC2208.
Buy It Now
Free Shipping Condition: New Location: China The driver board can drive hard disk brushless motors ,CD-ROM brushless motor and so on, the micro 3-wire or 4-wire. Without hall brushless motor . Speed ... moreadjust :0%-100%. 12dbi WIFI Antenna 2.4G/5.8G Dual Band Pole Antenna SMA Male with Magnetic Base.
Buy It Now
$169.00 Shipping Condition: New Location: Hong Kong SAR China Cnc Mill 3 axis NEMA34 MOTOR 4.5 N.m(637oz-in) package Idea For Medium MILL Conversion to Cnc Control INCLUDING 3x NEMA34 2 phase 4.5N.m Step Motor Maximum ... moreHolding Torgue 637 OZ/ INCH Size: SQ 86mm X 85mm Long Shaft: Dia 1/2 Inch X 1-1/4 Inch Long 3x 5.6A Micro step INDUSTRIAL GRADE DRIVE From 200 or 12800 Pulse per Turn DC:24 to 50V 1x 48v 10A 480W Power supply AC Input: 90 to 240V Power Can Supply up to 3 Axis 1x CNC SOFTWARE BREAKOUT BOARD Build in 5v 1A Power Supply for Control Signal IDEAL FOR CNC PARALLEL PORT SOFTWARE TURBOCNC. KCAM, MACH3 etc MENU: http:www.ebay.com/itm/321000374694 1x PARALLEL PORT CABLE Weight About 15 KG Control NEMA 34(4.5 N.m) step motor Running at 3000rpm Option: Change 3x 8.5 N.m(1200oz-in) Step Motor Add US$139 Size: SQ 86mm X 118mm Long Option: For 8.5N.m Motor 3x 7.8A Mirco step Drive Add US$80 Mirco step form 200 to 12800 step per Revelution Control by Mach3 R unning at 3000 rpm Option: Change 48V 15A 720W 4Axis Power Supply Add US$88 Shipping By Fed Ex YOU CAN BUY CNC PARTS HERE http:shop.ebay.com/merchant/yuntat_W0QQ_nkwZQQ_armrsZ1QQ_fromZQQ_ipgZ25 THANK YOU.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d72f%2Bf7%60%3E-13f9d1e494c-0xfc-
Buy It Now
$238.00 Shipping Condition: New Location: China This item includes: 3 PCS Nema 34 Stepper Motor with 1600 oz-in holding torque.With single shaft, 3 PCS Stepper Driver with 7.8A replacing M860, 1 PC ... moreNema 23 Stepper Motor with 425 oz-in, 1 PC Stepper Driver with 4.2A replacing M542 1 PC Power Supplies for 2 00W.24VDC, 1 PC Power supply for 400W-48VDC 1 PC Breakout Board& 1 Cable for free offering The Breakout Board is offered to you for free to buy this item above. So that you can set this kit up, and work in better condition. 1. Stepper motor for Nema 34 1, Technical Specifications Model Step angel( °) Motor Length L(mm) Rate Voltage(V) Rate Current(A) Phase Resistance( Ω) Phase Inductance(mH) Holding Torque(oz.in) Lead Wire(NO. Rotor Inertia(kg. c? Motor Weight(kg) 34HS5435C-37B2 1.8 151 5.7 3.5 1.9 22 1600 4 3.6 5 2. Stepper Motor Driver Detailed pic: Stepper motor driver DM860A: Http:www.longs-motor.com/ProductsView.asp?id=273&pid=83 Introduction: DM860A is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: L High performance. Low price. L Average current control. 2-phase sinusoidal output current drive. L Supply voltage from 24VDC to 80VDC. L Opto-isolated signal I/O. L Overvoltage. Under voltage, overcorrect, phase short circuit protection. L 14 channels subdivision and automatic idle-current reduction. L 8 channels output phase current setting. L Offline command input te
Buy It Now
$89.00 Shipping Condition: New Location: China Stepper motor driver DM2722A. 1 pc Nema 42 stepper motor 3256 oz.in=23NM, 6.0A, 4 leads, bipolar. Holding torque: 3256 oz-in ( 23 N. Stepper motor. Step ... moreAngle: 1.8 degree. P4 P5 is set to Y-axis, Y axis pulse. ).
Buy It Now
$3.00 Shipping Condition: New Location: China It also supports the universal FANUC compatible G instruction set. - 1 x Handwheel DDPMG. - Support the centring operation of X and Y axis. - Support ... moresimulation operation and during simulation, you can adjust the magnification to carefully observe whether the programming path is in line with expectations, and perform software limit.
Buy It Now
$3.99 Shipping Condition: New Location: China MK3-V:3 axis motion card works with Mach3 CNC system for all Windows platform. Output frequency: 2000 KHZ (2MHz). Mach3 Port Position: P1 Port. - Fully ... moresupport all Mach3 version. - 16 general-purpose input,8 output has speed function, the spindle actual speed Mach3.
Buy It Now
$233.00 Shipping Condition: New Location: China 4pc Nema 34 stepper motor 1232 oz.in bipolar,Dual Shaft 34HS1456B. Hording torque when DM860A run under high speed is also significantly higher than the ... moreother two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$1.99 Shipping Condition: New Location: China Rated power: 1500W. Stepper Motor Driver Current Adjustable 32 Subdivision for 42/57 Stepper Motor. TMC2209 V1.2 Stepper Motor Driver DC 4.75-28V 2A 3D ... morePrinter Parts for BTT SKR. 1PCS MACH3 Engraving Machine 5 Axis CNC Breakout Board With Optical Coupler.
Buy It Now
Free Shipping Condition: New Location: China High quality with Surface-mount Tech. Function choice ( Using DIP pins to achieve this function). When VCC=24V, R=2K,＞1/8W. When VCC=12V, R=1K, ＞1/8W. ... moreNote: When VCC=5V, R=0. PC PNP output. PC open connector output.
Buy It Now
$220.00 Shipping Condition: New Location: China 1 pcs Stepper motor driver DM542A ,PEAK current 4.2A, for nema23. 3 pc Nema 34 stepper motor 1600 oz.in 34HS5435C-37B2 single shaft. 1 pcs Nema 23 stepper ... moremotor 425 oz.in 23HS9430 single shaft. Nema 34 stepper motor.
Buy It Now
$99.00 Shipping Condition: New Location: Hong Kong SAR China Cnc Mill 3 axis NEMA23 MOTOR 22kg.cm MIRCO STEPPER FOR 400 TO 25000 STEP PER TURN Idea For Mini MILL Conversion to Cnc Control INCLUDING 3x NEMA23 2ph ... more22kg.cm Step Motor Maximum Holding Torgue 308 OZ/ INCH Size: Dia 56mm X 80mm Long Double Shaft: Dia 1/4 Inch X 3/4 Inch Long 3x Turning Knob for Manual Control 3x 4.2A Industrial Grade Mirco step Drive Mirco step form 400 to 25000 step per Revelution DC:24 to 50V 1x 36v 10A Power supply AC Input: 90 to 240V Power Can Supply up to 4 Axis 1x CNC SOFTWARE BREAKOUT BOARD Build in 5v 1A Power Supply for Control Signal IDEAL FOR CNC PARALLEL PORT SOFTWARE TURBOCNC. KCAM, MACH3 etc MENU: 1x PARALLEL PORT CABLE 1x PANIC STOP BUTTON Weight About 6.5 KG Control by Mach3 Running at 2500 rpm Option:Change 48v 10A Power Supply to 5 Axis 36v 13.3A add US$29 Shipping By Fedex YOU CAN BUY CNC PARTS HERE http:shop.ebay.com/merchant/yuntat_W0QQ_nkwZQQ_armrsZ1QQ_fromZQQ_ipgZ25 THANK YOU
Buy It Now
$2.59 Shipping Condition: New Location: China Input power: 400W. Adaptive power: ≤600W With or without Hall DC brushless motor. Input current: 3A. There is no hall hall automatic recognition, easy ... moreto use, the use of frequency conversion technology to achieve low noise.
Buy It Now
Free Shipping Condition: New Location: China Low speed anti-shake, low temperature rise, square wave open loop output, stepless speed regulation. Input power: 400W. Adaptive power: ≤600W With or ... morewithout Hall DC brushless motor. Input current: 3A.
Buy It Now
$227.00 Shipping Condition: New Location: China 4 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar 34HS5435C-02B2. Hording torque when DM860A run under high speed is also significantly ... morehigher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$89.00 Shipping Condition: New Location: China 1.4 pcs Nema 23 stepper motor 435 oz.in bipolar with single shaft. Nema 23 stepper motor 435oz-in=3.0 N.m. Hording torque when DM542A run under high speed ... moreis also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$122.00 Shipping Condition: New Location: China Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM542A. 4 pcs Nema 23 stepper motor with 425 oz.in 23HS9430.
Buy It Now
$3.00 Shipping Condition: New Location: China Added parsing error prompt, DDCS V3.1 has not been there, and it will stop directly if there is parsing error. - 1 x Handwheel DDPMG. It also supports ... morethe universal FANUC compatible G instruction set.
Buy It Now
$1.95 Shipping Condition: Brand New Location: China 1 x Adapter Breakout Board. The output port is P17 port. The output port is P1 port. Connectors: USB(Female)+25PIN(Male). 1 x USB Cable.
Buy It Now
$3.59 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
$0.86 Shipping Condition: New Location: China 5 Axis Stepper Motor Driver Interface Breakout Board, Features: For stepper motor driver-Can most connection 5pcs driver and control 5pcs motor in the ... moresame time-With 4-wire limit switch to insure our safty movement-With relay port to contro the cnc spindle-Working voltage is 5VDC and support with MACH3.EMC2,KCAM4 software Db25 pin( pc pin) The pin of the interface board Comment(signal) 1 Step 5 Fifth axis pulse 2 Step x X pulse 3 Dir x X axis direction 4 Stepy Y pulse 5 Dir y Y axis direction 6 Step z Z axis pulse 7 Dir z Z axis direction 8 Step 4 Fourth axis pulse 9 Dir 4 Fourth axis direction 10 Limit-1 Limit input interface 1 11 Limit-2 Limit input interface 2 12 Limit-3 Limit input interface 3 13 Limit-4 Limit input interface 4 14 Dir 5 Fifth axis direction 15 Vacant 16 Rly Relay control 17 En All axis enable 18-25 Gnd Gnd Package 100% Brand New 1 x 5 Axis Stepper Motor Driver Interface Breakout Board Shipping 1. Items will be sent out within 48 hours(except weekend and holidays) after we receive the payment. All items are shipped by Singapore or HongKong Post air mail without tracking number.Unless buyers pay extra money. 2. It is estimated that package will arrive in 10-30working days. holidays and weekends are not included) to most countries! If you donot get the items after 30 working days please email us we will Refoud or Reship. 3. Since air mail will takes long time for delivery. If you want items urgently, you could contact us to ask shipping cost of Express mail.such as DHL or EMS or TNT or UPS) 4. We are not responsible for any custom duty or import thanks 5. We only ship the item to the address listed in your paypal payment. Please make sure your shipping address is correct. 6. If you have any request(e.g. change address) Please put a note on paypal. Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-30 30 Working Days + Saturday + Sunday 5-9 10-14 15-20 21-25 26-30 35 United States Rate(item arrived) 9% 50% 21% 13% 7% Refund or Resend United Kingdo
Buy It Now
$3.89 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
$1.99 Shipping Condition: New Location: China This product is a drive module developed for inductive BLDC motor. The drive master chip is SNR8503M, and the special circuit for inductive motor drive ... moreis integrated inside the chip, supporting the Hall electric Angle of 120 degrees or 60 degrees, and the default is 120 degrees.
Buy It Now
$53.00 Shipping Condition: New Location: China Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM860A. 4 pcs Nema 34 stepper motor with dual shaft, 1600oz.
Buy It Now
$115.00 Shipping Condition: New Location: China 1 PCS Nema 42 Stepper Motor 42HS0460 With 1900oz-in 115mm 5.5A. 1 PCS Stepper Motor Driver DM2522A AC90~240V. Part No.: 42HS0460. Stepper motor driver ... moreDM2522A. Stepper motor. Application: Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters.
Buy It Now
$110.00 Shipping Condition: New Location: China 4 pcs Nema 23 stepper motor 425 oz.in bipolar 3A 23HS9430. Nema 23 stepper motor Stepper motor driver DM542A Hording torque when DM542A run under high ... morespeed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$89.00 Shipping Condition: New Location: Denmark 1pcs Stepper motor driver DM2522A AC90~240V. Stepper motor driver DM2522A. 1.1 pcs Nema 34 stepper motor 1700 oz.in bipolar Single shaft. Stepper motor. ... moreApplication: Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters.
Buy It Now
$3.00 Shipping Condition: New Location: China It is the new 3-axis Mach3 motion card. - 1 x Mach3 Motion Card. Download the latest version of Mach3 - Axis Backlash: YES. - Axis output number: 4 Axis ... more(high-speed optocouplers). - Slave Axis(Dual X/Y/Z): NO.
Buy It Now
$76.00 Shipping Condition: New Location: China 1PCS Stepper Driver DM860A with 7.8A replacing MD882. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase ... moredriver, what’s more, the positioning accuracy is also higher.
Buy It Now
$43.00 Shipping Condition: New Location: China 4 pc Nema 17 stepper motor with 48 oz. in,4 leads, 1.7A 17HS4401N. Hording torque when DM420A run under high speed is also significantly higher than the ... moreother two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$55.00 Shipping Condition: New Location: China 3 pcs Nema 34 stepper motor 878oz. in bipolar with dual shaft. 2.3 pc Stepper motor driver High Perfermance Stepper Driver DM860A Up to7.8A, 24-80VDC. ... moreStepper Driver DM860A Up to7.8A, 24-80VDC, DM860A.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China Mach3 Interface Board. The output port is P17 port. Spindle speed. The output port is the P1 port. A pplication area. 25Pin Cable.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China Stepper Motor. The output port is P17 port. Vibration Motor. Spindle speed. The output port is the P1 port. Rosin Heat Press Machine. Application area. ... moreSliding Table.
Buy It Now
Free Shipping Condition: New Location: China Support various versions of MACH3 software and support the latest version. Maximum 100KHZ output per axis,can be connected to common anode or common cathode,input ... morelevel is 5V,stepper or servo motor driver with optocoupler input (pulse + direction).
Buy It Now
Free Shipping Condition: New Location: China Maximum support 5 axis stepper motor driver. Step working axis: Maximum connect 5 axis independent drive. Five axis working indicator light, intuitively ... moredisplay working status. 1 Drive Board. If you do not receive our reply within 48 hours, pls.
|
|
|
 |