|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
$130.00 Shipping Condition: New – Open box Location: Ukraine Low frequency signal generator G3-120 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better characteristics. ... moreThis device can be used for wide measurement range. Low frequency signal generator G3-120 is sinusoidal(main mode) and rectangular(optional mode) signals source and is designed for researching. Configuring and testing of systems and devices used in electronics, communications, automation, computing and measurement technology, instrumentation in mobile repair and calibration systems. Ability to work with KOP(public channel) and AMS(Automated Measurement System) is not provided. General technical characteristic: Ambient temperature- of 243K to 323K(from-30 º C to +50 ° C) Relative humidity- up to 98% at a temperature of 298K(25 ° C) Atmospheric pressure- 60kPa to 107kPa(450mm.Hg. 800mm.Hg. Frequency range of device low-frequency signal generator G3-120- from 5 Hz to 500 kHz is covered by five subranges continuously tunable within the subranges: I subrange(x1) 5Hz-50Hz; II subrange(x10) 50Hz-500Hz; III subrange(x10 2) 500Hz- 5kHz; IV subrange(x10 3) 5 kHz. 50 kHz; V subrange(x10 4) 50kHz-500kHz; Edges range reserve. And overlap between the subranges is at least of frequency setting basic error; Basic frequency error of device low frequency signal generator G3-120- does not exceed ±(3 +30/ ƒ) in frequency range from10Hz to 300kHz and ± 5% in the rest frequency range. Where ƒ- the nominal value of fixed frequency, Hz; Additional frequency error from ambient temperature changes for every 10 ° C in operating temperature range does not exceed: 5 ∙ 10-3 ƒ in frequency range from 50Hz to 300kHz(II-V subranges) 1 ∙ 10-2 ƒ in frequency range from 5Hz to 50Hz(I subrange) Over 300 kHz to 500 kHz(V subrange) Frequency instability of device low-frequency signal generator G3-120 at the end of time required to setup mode does not exceed: 2 ∙ 10-3 ƒ up to 200 kHz and ± 5 ∙ 10-3 ƒ up to 500kHz for a
Buy It Now
$235.00 Shipping Condition: New – Open box Location: Ukraine High frequency signal generator G4-176 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better ... morecharacteristics. This device can be used for wide measurement range. High frequency signal generator G4-176 is designed to control. Regulate and test various electronic equipment operating in manual and automatic control mode via public channel(KOP) Generator provides various measurements of device’s amplitude- frequency characteristics. Actual sensitivity and curve receiver fidelity. Operating in unmodulated oscillation(HK) Amplitude modulation(AM) Frequency modulation( CM) and television modulation(TV) modes. High frequency signal generator G4-176 can serve as a un modulated and uncalibrated signals source. Used as a local frequency oscillator for various transformations. Generators are designed to be used in calibration agencies. Repair shops, laboratories and workshops. This device was also used in USSR and Russia army. So it has best quality. Longevity and permanence characteristic. Condition: NEW(not used. An old stock) Tested and 100% workable. If necessary. We can provide calibration certificate from Government standardization institute(+145-265usd) Also we can provide other resistance. Capacitance and inductance standards, decade box and other etalons. Also we can provide other resistance. Capacitance and inductance standards, decade box and other etalons. If you haven’t found the needed item in my listing. Please contact me. I’ll try to help you. Technical characteristics of devices high frequency signal generators G4-176: Frequency range- from 0.1 MHz to 1020MHz; Device high frequency signal generator G4-176 frequency discreteness change: In the range from 0.1 MHz to 160 MHz- 0.1 kHz; In the range from 160 MHz to 1020MHz- 1.0 kHz; Frequency setup acceptable basic error limit- is not more than ± 1.5• 10-5% Output voltage adjustment limits at load of 50 Ohm and 75 Ohm in"HK" and" CHM" modes: In the frequency ran
Buy It Now
$190.00 Shipping Condition: New – Open box Location: Ukraine Basic error set by harmonics coefficient CK6 -10 CK6 -10basic error does not exceed CK6 -10weight - ≤ 18 kg. Also we can provide other resistance, capacitance ... moreand inductance standards, decade box and other etalons.
Buy It Now
$205.00 Shipping Condition: New – Open box Location: Ukraine High frequency Signal generator G4-123 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better ... morecharacteristics. This device can be used for wide measurement range. High frequency signal generator G4- 123 is designed to configure, control and testing of various radio technical devices of centimeter wave range. Generator can be used as a source of uncalibrated in high-frequency signal terms to power measuring lines. Directional couplers. High-frequency bridges, antennas. Filters, input circuits receivers. Etc. Generator G4-123 is designed to used in laboratory. Factory and field conditions. Features of device high-frequency signal generator G4- 123: two identical high frequency output; ability to use both outputs; modulation CHM, IM. General technical characteristic: Frequencies range- from 3000MHz to 4500MHz; Basic frequency error is not more than ± 1.25% Output power at load is 50 Ohm: 40 mWatt- in the range from 3000MHz- 3400MHz; 15mWatt- in the range from 3400MHz- 4500MHz; A smooth output power variation of device high frequency signal generator G4- 123 at load 50 Ohm is at least 30 dB; Parameters of high frequency output im pulse with external modulation: rise time- 0.3 mks; cut duration- 0.5 mks; impulse irregularity- 10% Deviation of output impulse duration from modulation impulse duration- is not more than ± 0.5 mks; rise and fall instability- 0.5 mks; Im pulse repetition frequency of device high-frequency signal generator G4-123 with internal modulation meander- 1000 Hz ± 100 Hz; Asymmetry- 10% Output impedance- 50 Ohm; Power consumed by device high-frequency signal generator G4-123– is not more than 150V ∙ A; Dimensions– 390x300x280mm; Weight- is not more than 18kg; Normal operating conditions of device high-frequency signal generator G4-123: Ambient temperature- 20 º C ± 5 º C; Relative humidity at temperature 20 º C ± 5 º C- 65% ± 15% Atmospheric pressure- 100kPa ± 4kPa; Voltage su
Buy It Now
$200.00 Shipping Condition: New – Open box Location: Ukraine Low frequency signal generator G3-122 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better characteristics. ... moreThis device can be used for wide measurement range. Low frequency signal generator G3-122 is a source of electrical sinusoidal oscillations with high setting accuracy and frequency stability in range from 0.001 Hz to 1999999.999 Hz, with frequency setting discreteness of 0.001 Hz. Device low frequency signal generator G3-122 is designed for low frequency control and testing various purposes equipment, for integration into automated measuring systems(AIC) Features: Remote control of common channel(KOP) A wide frequencies range; High accuracy and stability of frequency setting; Direct readout of output level in voltage units; Internal self-control system. Technical characteristics of device low frequency signal generator G3-122: The device is a source of electrical sinusoidal oscillations with high setting accuracy and frequency stability in range from 0.001 Hz to 1999999.999 Hz, with frequency setting discreteness of 0.001 Hz and is designed for low frequency control and testing various purposes equipment, for integration into automated measuring systems(AIC) Operating using conditions: Ambient temperature from 5 ° C to 40 ° C; Relative humidity up to 98% at 25 ° C; Atmospheric pressure 450 mm.Hg. 800mm.Hg. Low frequency signal generator G3-122 frequency range– 0.001 Hz to 2 MHz with frequency setting discreteness of 0.001 Hz; Frequency setting basic error- ± 5 ∙ 10-7 fn in 12 months; Instability: ± 5 ∙ 10-9 fn– in 15 minutes; ± 3 ∙ 10-8 fn– in 16 hours; Device low frequency signal generator G3-122 output voltage range- 0.2 mV. 2500mV(50 Ohm) output voltage discreteness: 0.001 mV- 0.2 mV-1.999mV; 0.01 mV- 2 mV. 19.99mV; 0.1 mV- 20mV. 199.9mV; 1 mV- 200mV-2500mV; Additional output voltage level attenuation is provided in device low frequency signal generator G3-122 at 40 dB when connected to t
Buy It Now
$220.00 Shipping Condition: New – Open box Location: Ukraine High frequency signal generator G4-164 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better ... morecharacteristics. This device can be used for wide measurement range. High frequency signal generator G4- 164( G4164. G 4164. G-4- 164. G4 164) High frequency signal generator G4-164 is designed to control. Regulate and test various electronic equipment operating in manual and automatic control mode via public channel(KOP) Device can serve as a un modulated and uncalibrated signals source. Used as a local frequency oscillator for various transformations. Generator provides various measurements of device’s amplitude- frequency characteristics. Actual sensitivity and curve receiver fidelity. Operating in unmodulated oscillation(HK) Amplitude modulation(AM) Frequency modulation( FM) and impulse modulation(IM) modes. High frequency signal generator G4-164 is designed to be used in calibration agencies. Repair shops, laboratories and workshops. Devices is a high frequency signal source in frequency range from 0.1 MHz to 639.999 MHz working in HK. AM, CM and IM modes. Operation mode settup is provided by keyboard control located on generator front panel. Enter of required parameters such as frequency. Output voltage, amplitude modulation coefficient, frequency deviation shall be made either through keyboard or by means of kvazi parameters settings on generator front panel. Device high frequency signal generator G4-164 setup parameters can be saved and numbered in internal memory for assigned to subsequent call. You can save up to 63 sets of generator parameters. These operations are carried out under control of embedded micro-EBM computers H1830BE51 that can significantly reduce energy consumption and improve reliability and manufacturability in comparison with the generator base model. Modulation of device high-frequency signal generator G4-164 carrier frequency is carried out both from an modulating oscillation internal source as well as from ou
Buy It Now
$180.00 Shipping Condition: New – Open box Location: Ukraine Low frequency signal generator G3- 110 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better ... morecharacteristics. This device can be used for wide measurement range. Low frequency generator G3-110 is designed to use as electric sinusoidal oscillations source in the range from 0.01 Hz to 2 MHz with high accuracy and frequency stability. General technical characteristic: Frequency range from 0.01 Hz to 2 MHz(discrete 0.01 Hz) Main frequency error ± 3* 10-7 f Hz Frequency instability at discrete points. Hz: ± 5* 10-9 f(for 15 min) ± 1* 10-8 f(for 3 hours) ± 3* 10-8 f(for 16 hours) Technical characteristics of generator G3-110 Frequency range 0.01 Hz- 2 MHz(discrete 0.01 Hz) Frequency acceptable basic error limit ±3·10-7 f Hz Output voltage 1 V(50 Ohm) Voltage attenuation 0-85 dB(discrete 1 dB) Output voltage instability for 3 hours ±0.3% 100 Hz- 2 MHz) Harmonic distortion 0.5% 10 Hz- 2 MHz) Frequency instability at discrete points. Hz ±5·10-9 f(for 15 min) ±1·10-8 f(for 3 hours) ±3·10-8 f(for 16 hours) Level of side spectral components-66 dB Power consumption Generator 80 V·A Programator 50 V·A Voltage supply 220±22 V. 50±0,5 Hz or 220±11 V, 400+28-12 Hz Weight 16 kg Dimensions 488х135х40 mm Low frequency generator G3-110 is designed to use as electric sinusoidal oscillations source in the range from 0.01 Hz to 2 MHz with high accuracy and frequency stability. Generator’s G3-110 functionality is greatly enhanced if it is used in with the programmer 321. In such a combination. The measurements automation is provided, eliminated operator’s error during the generator output parameters installation, increases the intensive use operational reliability. Programmer 321 controls device’s generator G3-110 frequency and output voltage. By the program previously stored in memory. Number of words in program 1- 15. Number of frequency and voltage decimal places in one word is- 11. Program
Buy It Now
$235.00 Shipping Condition: New – Open box Location: Ukraine High frequency signal generator G4- 111 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better ... morecharacteristics. This device can be used for wide measurement range. High frequency signal generator G4- 111 is a microwave oscillations source with non-calibrated at power outputs. Provides calibration of power meters. Loss measurements, attenuation. KCBH, impedance. Etc. Can be used as interference simulators or signal transmitters, also for antennas and antenna circuits measurements. Device high-frequency signal generator G4-111 can be used at testing semiconductor devices such as mixer and multiplier diodes varaktors. Etc. General technical characteristic: Frequency range- 6GHz-17. 85GHz; Accuracy of frequency setting– is not more than ± 0.5% Frequency instability of device high-frequency signal generator G4-111 for 15 minutes- is not more than 1 ∙ 10-4; Parasitic frequency deviation- 1 ∙ 10-5 ƒ( 50Hz-20kHz) Output power of device high-frequency signal generator G4-111- 40mWatt( 6GHz-8. 9GHz) 20mWatt(8.9 GHz-12. 05GHz) 8mWatt( 12.05 GHz-16. 6GHz) 4mWatt(16.6 GHz-17. 44GHz) 2mWatt( 17.44 GHz-17. 85GHz) Output power attenuation- 0dB-30dB; Output power level signal instability of device high-frequency signal generator G4-111 for 15 minutes- 0.1 dB; Signal power at output for connection ECCH(50 Ohm coax 7/3mm) 300mWatt(6GHz-9GHz) 500mkWatt(9GHz-12 7GHz) IM external mode: repeat frequency- 0.05 kHz. 10 kHz; amplitude- 9V-12V; impulse duration- 0.5 mks-50mks; duration of rise and fall- 0.2 mks and 0.3 mks; Meander" repeat rate: 1 kHz ± 10% on inside modulation; 0.4 kHz- 2 kHz- on external modulation; Electronic tuning line of device high-frequency signal generator G4-111- 3 MHz; Power supply of device high-frequency signal generator G4-111: 220V. 50Hz; 115V. 400Hz; Power consumption- 140V ∙ A; Dimensions– 490x175x355mm; Weight of generator G4-111- 24kg. This device also can be named as: G4
Buy It Now
$170.00 Shipping Condition: New – Open box Location: Ukraine Signal generator G3- 113 analog of NoiseCom, General Radio. Boonton, HP Agilent, Fluke and general Electric, but has the same or better characteristics. ... moreThis device can be used for wide measurement range. Generator G3-113 is designed for researching. Configuring and testing different systems and devices used in electronics, communications, automation, computing and measuring equipment. General technical characteristic: Frequency range 10Hz-99.9 kHz increments through 1Hz(10-999Hz) 10Hz(1-9.99 kHz) 100Hz(10-99.9 kHz) Basic frequency error does not exceed ±(0.5 +50/Fn) Where Fn- set frequency range in Hz. Low frequency signal generator G3-113 is used in electronics. Communications, automation, computing and measuring equipment. Generator G3-113 is source of sine signal precision wave form and increased stability of output voltage level with a remote control for frequency and amplitude in the code 8-4-2-1. Frequency accuracy class of device- 0.5. Voltage accuracy class- 2 in the frequency range from 100 Hz to 99.9 kHz and 6 in the frequency range from 10Hz to 99 Hz. Operating conditions G3-113: ambient temperature from 278 to 313 K(from 5 to 40 ° C) Relative humidity up to 95% at an ambient temperature 30 ° C and atmospheric pressure from 60 to 106 kPa(from 460 to 800 mm Hg) voltage supply 220 V ± 22 V with the industrial frequency of 50 Hz. Technical characteristics of generators G3-113 Output frequency is set in range from 10Hz to 99900Hz with increments of 1Hz in the subrange from 10Hz to 999Hz. 10 Hz in subrange from 1 Hz to 9.990kHz, 100Hz in subrange from 10 kHz to 99.900 kHz. Basic frequency error does not exceed ±(0.5 +50/ Fn, where Fn- set frequency range in Hz. Additional frequency error caused by changes in ambient air temperature for every 10 ° C in working temperature range does not exceed ± 10• 10-4 Fn. Additional frequency error caused by changes in load from idle value to its maximum value does not exceed ± 0.5• 10-4 Fn. Frequency instability of the generator a
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Midwest ATE Test Equipment Recyclers www.midwestate.com 708-420-4204 info@midwestate.com Noisecom NC6110 Noise Generator 30 day warranty. With fresh Calibration ... moreNoiseCom NC6110 Noise Generator. 100 Hz to 1.5 GHz Condition: Pre-Owned The NC6000 Series noise generating instruments are designed for applications on the test bench. Or in test stations in which an NC6000 Series unit is incorporated with other equipment that provides a wide variety of functions. Each instrument contains a Noise Com precision noise source that delivers repeatable, symmetrical white Gaussian noise. The noise source is integrated with an amplifier, 10 dB attenuator with 1 dB steps, and power supply.The instruments have a 50 ohm output impedance. Features: Output: White Gaussian noise Attenuator: 0 to 10 dB in 1 dB steps; other options available Impedance 50 ohms Typical VSWR 1.5:1 Standard: NC6000) 8.5 in. wide x 5 in. high x 12.25 in. deep Power 120 VAC. 60 Hz Operating-10°to +60°C temperature Applications: CATV testing Development testing HDTV field testing General purpose* Contact Midwest ATE E-mail: info@midwestate.com Phone: 708-420-4204* We carry a large supply of quality refurbished and used test equipment from all the major manufacturers. For multiple quantities please contact us, if we don't have it we'll be glad to find it for you! Product Condition Midwest ATE stands apart from other organizations that sell refurbished or used electronic test and measurement equipment. All test equipment products are 100% Refurbished by our in-house test lab engineers. Midwest ATE has developed rigorous re-certification procedures to ensure our products are shipped with the highest quality.
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Make: NoiseCom. Model: NC6110. Noise Generator, 100Hz to 1.5GHz. Options: 2, 4, 6, 8, 9. 8-BNC female output connector. rack mountable unit, 17 in. wide ... moreby 3.5 in. high by 13 in.
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Make: NoiseCom. Programmable Precision C/N Generator Dual Band. 3- 50ohm input and output impedance. Model: UFX-BER 892-1850-3.
Buy It Now
$120.00 Shipping Condition: For parts or not working Location: Singapore We look forward to receive your supports.
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Title: Nice NoiseCom Noise/Com NC6109 Noise Generator 100Hz-1GHz. 10 MW GUARANTEED! Description: This auction is for one NoiseCom NC6109 Noise Generator ... more100Hz- 1000MHz. 10 MW in great TESTED& GUARANTEED condition! Fully functional with a 30 day ROR. The Noisecom NC6109 contains a precision noise source that delivers repeatable. Symmetrical white Gaussian noise across a frequency range of 100 Hz to 1 GHz. The NC6109 noise source is integrated with an amplifier, a 10 dB 1 dB/step attenuator, and power supply. The NC6109 has a 50 ohm output impedance. Take a GOOD look at the pictures and good luck bidding! Please ask any and all questions before bidding. And I will do my best to answer them. ALL ITEMS ARE SOLD AS-IS. UNLESS NOTED OTHERWISE ABOVE! PLEASE READ: I strive to provide an accurate description and complete disclosure of my selling practices. If the item does not meet your expectations please contact me prior to leaving feedback so that I may address any issues. I make every effort to ship within 3 BUSINESS days of receiving payment. My shipping costs are based on the shipping weight of the item. Insurance and the cost of packaging. Most items are shipped via FedEx ground for the price quoted above. All international shipments are by USPS Priority mail international. International bidders are responsible for all customs fees. If there is not a"buy it now" price listed on the item, it means I intend to let the auction run to completion so please do not ask me to end the auction early, that is unfair to other bidders. All my"buy it now" items also have the best offer feature, so please feel free to use it. If an item is listed as no international shipping, I will not ship it outside of the US but will ship to a US address for international bidders. Ebay is very strict on allowing sellers to remain with ebay based on their feedback and detailed seller ratings numbers. I strive to have all my buyers 100% satisfied. If you have any questions or issues after receiving your item, PLEASE cont
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Model: UFX7110. Make: NoiseCom. Programmable Noise Generator, 100Hz-1.5GHz.
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Up for sale today is: NOISECOM NC6107 100Hz-100MHz NOISE GENERATOR 14 DAY RIGHT OF RETURN Normal 0 false false false MicrosoftInternetExplorer4 Disclaimers ... moreThe pictures include everything that you will get. Unless specifically noted in the description. If you do not see it in the photo or in the description block above. It is not included in the auction. Talented Technologies is not responsible for international customs fees. We do not ship to P.O. Boxes or unverified Paypal addresses. And we reserve the right not to sell to eBay buyers with excessive negative feedback. Product condition definitions and terms“x day money back” not valid if item has been. In any form, tampered with) Item guaranteed to be operational for x days from receipt. Should the item fail to be operational, it may be sent back at the expense of the buyer to be tested by our staff. Refund issued at our discretion based on those tests. Shipping costs cannot be refunded. Return policy applies only to buyers within the United States. x day Warranty" not valid if item has been. In any form, tampered with) Item guaranteed to be operational for x days from receipt. Should the item fail to be operational, it may be sent back at the expense of the buyer to be tested by our staff. Item repair or replacement issued at our discretion based on those tests. If item repair or replacement is not available, a refund will take place. Shipping costs cannot be refunded. Warranty applies only to buyers within the United States. Payment Payment must be made within 4 days of auction close. We reserve the right to cancel the transaction and file an Unpaid Item Claim after 4 days. Buyers in California please add 8.00% sales tax to all purchases. If you are a reseller and want to request a resellers' tax exemption. Please ask us for our BOE form which you will need to fill out, sign and fax it to us. We'll send you a new invoice with the sales tax removed. We accept: Paypal Confirmed addresses only. Bank Wire Transfer Payment upon pickup. No personal che
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Make: NoiseCom. Precision SNR Generator, 1080 MHz center frequency. Model: UFX-EBNO/1080.
Buy It Now
$113.42 Shipping Condition: Used Location: Farmingdale, United States Make: NoiseCom. Precision SNR Generator, 60 & 372 MHz MHz Center frequencies. Model: UFX-EBNO/60/372.
|
|
|
 |