|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 3 Axis TB6560 CNC Stepper Motor Driver Board 1.5A-3A*NEW* 3 Axis TB6560AHQ Stepper Motor Driver Controller Product Features: Toshiba TB6560AHQ chip- High ... morepower. Maximum 3.5A drive current chipset! 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step, Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors*Attention: This driver is 1.5A-3A version. Which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A. If the rated current your stepper motors is below 1.5A. You can choose the 0.5A-2.5A version. Please let us know which version(1.5A-3A version is default) you need immediately after placing an order. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Deta
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China This function is widely applied in RBI machine, Conveyor etc. EMA232-5615S4 Nema23 Stepper Motor. Stepper motors and drivers from ENGMATE. ™ 3 Axis Kit ... morefor CNC DIY. 5 Axis Professional Breakout Board.
Buy It Now
Free Shipping Condition: New Location: United States The DQ860MA is an economical microstepping driver based on patented technology of Wantai Motor. It is suitable for driving 2-phase 4-phase hybrid stepping ... moremotors. 3PCS Nema34 Stepper Motor WT86STH118-6004A with 1232oz-in holding torque,5.6A current,118mm motor body length,Single shaft.
Buy It Now
Free Shipping Condition: New Location: United States 1 PC Nema 34 stepper motor single shaft 85BYGH450C-060 with 12N. m 1700oz-in holding torque 6A. 2PCS Nema 23 Stepper Motor with Single shaft 425oz-in ... moreHolding torque. 1PC CNC Stepper Driver DQ860MA with 7.8A peak current, 256 Microstep, 24-80VDC;.
Buy It Now
Free Shipping Condition: New Location: China Install GRBL 1.1 firmware. --Integrated 3pcs A4988 drivers, directly connect to four wire stepper motor. for Laser Engraving machine, Drawer Machine, ... moreCNC Engraving Machine etc. support XYZ axis, double Yaxis.
Buy It Now
Free Shipping Condition: New Location: United States CNC Router Single One Axis 3.5A TB6560 Stepper Motor Driver Controller Board SKU:A88# Description TB6560AHQ is the stepper motor driver chip. The chip ... moreis highly integrated, simple peripheral circuits. High reliability, and part of the motor 57 for driving stepping motor 86, when the largest segment range from 0 rpm to a speed of 300 rpm. Features* high integration and high reliability of the stepping motor driver* interface with ultra high speed optical isolators* High anti-jamming capability* The maximum drive current of 3.5A( peak) Main function* whole-step. 1/ 2, 1/ 8, 1/ 16 segments. step by step adjustable current 0.5-3A* Automatic overheat protection* Optional automatic semi- flow* Adjustable current decay fourth gear* LED indicates power and working status* Support for offline. Enable. Lock etc. Package list: 1* Single Axis 3A TB6560AHQ Stepper Motor Driver Board NOTE We try our best to make every transaction perfectly, just for winning your F ive-Star rating. If you have any dissatisfaction. Please contact us. We will give you the most satisfactory results. PLEASE don't leave a neutral or negative easily. Shipping Item will be shipped within 24 hours on payment received from Hong Kong using Airmail. Only shipped to buyer's PayPal address. Please confirm with your PayPal address before you bid. Delivery time depends on destination and other factors. It may takes up to 30 business days. Optionally. Express Shipments with tracking service via EMS/DHL/UPS with a quoted delivery time of 5 to 7 business days is also available. Here is the estimated time for your reference only: Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-25 30 Working Days + Saturday + Sunday 5-9 10-14 15-20 21-25 26-35 40 United States Rate(item arrived) 9% 50% 21% 13% 7% Refund or Resend United Kingdom Rate(item arrived) 10% 62% 20% 3.5% 4.5% Refund or Resend Australia Rate(item arrived) 23% 50% 13% 8% 6% Refund or Resend Europe(Exclude Russia) Rate(item arrived) 2.5% 2
Buy It Now
$11.00 Shipping Condition: New Location: Hoffman Estates, United States Project Artois Crejz Project Artois Crejz MX3660- 3-Axis DSP Based Digital Stepper Drive Max 60 VDC/ 6.0A[gallery] Features Adopting latest DSP control ... moretechnology and Leadshine advanced stepper control algorithm complete control for 3 axes. Each axis can have its own configurations Step& direction control 20-60 VDC supply voltage Output current from 1.45 to 6.0A per axis 8 micro step settings: 1. 1/2, 1/4, 1/8, 1/10, 1/16, 1/32, 1/64 8 output current settings: 1.45. 2.08, 2.72, 3.37, 4.05, 4.72, 5.35, 6.0 A Built-in breakout board 5 digital inputs. 4 genral outputs, one 0-10 VDC analog output DIP switches for micro step and output current configurations Anti resonance for low and middle speed Excellent high speed performance Extra low motor heating& noise; smooth movement Able to drive NEMA 17. 23, 24, and 34 stepper motors Built-in breakout board with DB25 connector and IO's for easy setup with many CNC control systems such as Mach3 and EMC Easy to install and simple to implement Automatic idle current reduction to 50% More Details: Orders within the United States are shipped by UPS or Fedex Ground or the US Postal Service(Priority Mail) Which takes 1-5 business days depending on your location in the US. For international orders, please send us an email to quote the shipping fee first. We use USPS or UPS or Fedex to ship. Your order will usually ship within 2-5 business days after you receive an emailed order confirmation from Automation Technologies Inc. Automation Technologies Inc. does not ship to PO boxes. For security reasons we can only ship to your credit card billing address. If you would like us to ship to a different address you will need to call your credit card company and have them add an alternate address to your card. We will make all efforts possible to ship your order within 1-5 business days after receipt of payment. We do not ship on Saturdays or Sundays. All orders placed on Saturday and Sunday will be processed the following Monday. During the holidays and on Sundays. O
Buy It Now
Free Shipping Condition: New Location: China ▶Stepper Motor:X/Y1/Y2/Z. The positive and negative of the input power must not be reversed, and the reverse connection will burn. ▶Connection:USB Cable. ... more1 USB cable. Turn on the power after the electrical connection is completed.
Buy It Now
$4.99 Shipping Condition: New Location: China The factory default GRBL firmware supports 3-axis CNC and 2-axis laser engraving. Supports GRBL firmware and BenBox firmware. GRBL is a lot of compatible ... moresoftware for open source projects, which can be downloaded from the official website.
Buy It Now
$16.40 Shipping Condition: New – Open box Location: Westfield, United States The control board type is a 3-axis control board that is perfect for your industrial automation and motion control needs. The limit switch type is normally ... moreopen, and it has a number of axes of 3. The board is made in the United States and is brand Genmitsu. With this controller board, you can control your stepper drive form with ease.
Buy It Now
Free Shipping Condition: Used Location: New Paris, United States Call for better pricing!
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 3 pcs Nema 23 stepper motor 425 oz.in bipolar 23HS9430. Nema 23 stepper motor Stepper motor driver DM542A Hording torque when DM542A run under high speed ... moreis also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 1.3PCS Nema34HST9805-02B2 stepper motor 878oz. in=7.0N.m 2A 98mm ,dual shaft. 1.Nema34HST9805-02B2 stepper motor 878oz. 2.3PCS Stepper motor driver High ... morePerfermance Stepper Driver DM860A Up to7.8A, 24-80VDC.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Set Professional ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6560 Set Standard ... moreDriver Board is equipped with TB6560AHQ chip.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA242-8840S4 Nema24 Stepper Motor. This function is widely applied in RBI machine, Conveyor etc. Stepper motors and drivers from ENGMATE. ™ 3 Axis Kit ... morefor CNC DIY. 5 Axis Professional Breakout Board.
Buy It Now
$20.10 Shipping Condition: New Location: Bryan, United States Mach3 (demo). Nema 17 Stepper Motor Driver CNC Kit. Nema 17 stepper motor, Model 42BYGH404. Step Angle: 1.8 deg. Resistance per phase: 30 ohm. Holding ... moreTorque: 3.4 Kg-cm (47.2 oz-in).
Buy It Now
Free Shipping Condition: New Location: United States 【USA】3 Axis Nema23 stepper motor 3A/425oz. 1 x CD include English user manual and usbcnc software. 4 Axis USBCNC breakout board. This interface board ... moreis based on USBCNC MK1 and just use in our provide softwareand function, can not support update the firmware and use other versions of the software and function.
Buy It Now
Free Shipping Condition: New Location: China The traditional engraving machine, you need work for engraving machine with computer, the worker need cooperate between engraving machine and computer. ... moreworking inefficiency and operation is not convenient.
Buy It Now
Free Shipping Condition: New Location: China CNC turntable support. Manual function, and support for machine tool input through machine input devices, such as handheld devices, and embedded support ... morefor manual operation through computer input devices such as keyboard and mouse.
$2.99 Shipping Condition: New Location: China Motor Type : Stepper Motor. Stepper Motor:X/Y1/Y2/Z. Connect Laser:2pin/3pin/2pin-2pin. Connection:USB Cable. 1 USB cable. Turn on the power after the ... moreelectrical connection is completed.
Buy It Now
$50.00 Shipping Condition: New Location: China Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM860A:(Nema34 stpper motor use this driver).
Buy It Now
Free Shipping Condition: Used Location: Osseo, United States Advantech PCL-839 Rev.A1 3-Axis Stepping Motor Control Card 16-Bit ISA with DB37 USED. WORKING | AUCTION TERMS: 30-day DOA ITEM DESCRIPTION: You are buying ... morea used. Working. Advantech PCL-839 Rev.A1 3-Axis Stepping Motor Control Card 16-Bit ISA wtih DB37 Cable and Wiring Board Main Features: Independent. Simultaneous control of three stepping motors Optically-isolated outputs Five isolated digital inputs per axis for limit switches Half-size PC add-on card Up to 200 kpps step rate 16 x DI/O. This item has been removed from a working environment and tested by a qualified technician. You will received this item as pictured. No cables or accessories other than those mentioned or pictured in the listing will be included. 30-Day Warranty! ITEM PICTURES: PAYMENT: WE ACCEPT PAYPAL. ALL CREDIT CARD PAYMENTS MUST BE MADE THROUGH PAYPAL! IF YOU NEED TO SEND US A NOTE OR A MESSAGE DURING CHECKOUT. PLEASE DO NOT US ADD NOTE IN THE CHECKOUT PART OR IN PAYPAL. INSTEAD SEND US A MESSAGE THROUGH EBAY OR EMAIL US DIRECTLY! WE RESERVE THE RIGHT TO DENY ANY PAYMENT THAT WE CONSIDER FRAUDELENT OR SUSPICIOUS! shipping: PLEASE NOTE THAT FREE SHIPPING OPTION IS NOT AVAILABLE TO ALASKA. HAWAII AND US TERRITORIES AND IN MOST CASES THERE IS GOING TO BE A SURCHARGE. BUYERS FROM ALASKA. HAWAII AND US TERRITORIES PLEASE CHOOSE USPS PRIORITY MAIL INSTEAD OF THE FREE SHIPPING OPTION. ALL PACKAGES WILL BE SHIPPED THE FOLLOWING BUSINESS DAY AFTER THE PAYMENT IS CLEARED VIA FEDEX GROUND. USPS PARCEL POST OR USPS FIRST CLASS WITH TRACKING INFORMATION UNLESS EXPEDITE OR INTERNATIONAL SHIPPING IS REQUESTED. PLEASE NOTE. ALL UPS QUOTED RATES WOULD BE SUBSTITUTED FOR EQUIVALENT FEDEX SERVICE UNLESS REQUESTED OTHERWISE. SHIPPING COST IS FIXED FEE. NON-NEGOTIABLE AND NON-REFUNDABLE. IT INCLUDES PACKING MATERIAL COSTS AND HANDLING EXPENSES. ANY MERCHANDISE SENT TO ANOTHER COUNTRY MAY BE SUBJECT TO DUTY UNDER THE CUSTOMS REGULATIONS OF THAT COUNTRY. TECHYPARTS. LLC. DOES NOT MAINTAIN OR PROVIDE INFORMATION CONCERNING THE ASSESSMENT OF CUSTOMS DUTY. CARRI
Buy It Now
Free Shipping Condition: New Location: Wichita, United States Control package off a CNC3020 CNC rout. We needed the table and spindle, but we did not need the control system.
Buy It Now
Free Shipping Condition: New Location: Milner, United States CNC & 3D Printing. 4x8' Rail + Ballscrews Set (20mm). Automation & Linear Motion.
Buy It Now
Free Shipping Condition: New Location: China And integrated heat dissipation aluminum alloy. add the fan to force heat dissipation. The stepper motor drive increases the self-recovery fuse. Improved ... moreUSB interface: The USB interface is patch soldering, transport collision and improper use, easy to drop, now changed to plug-in, very strong.
Buy It Now
Free Shipping Condition: New Location: United States World Shipping. 7 Days Money Back. 3 Axis CNC Router TB6560 Stepper Driver + Display + Control Pad + Aluminium Box Descriptions I. About the 3rd Generation ... moreTB6560 Stepper Controller Box This stepper controller box has been upgraded to an intelligent and industrial-level driver board set. The redesigned PCB board enables smoother control of motors. The totally enclosed optical isolation and bipolar constant-current chopper ensure a low noise& low vibration operation environment. Helping to avoid creeping at a low speed. Internally built manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& C
Buy It Now
Free Shipping Condition: New Location: United States Part No.: 57BYGH627 single shaft. 3 PCS Stepper Driver with 4.2A DQ542MA replacing M542 . 2, Stepper Motor Driver with 4.2A Current, DQ542MA. It is designed ... morefor use with 2-phase hybrid stepper motor of all kinds with.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China World Shipping. 7 Days Money Back. 3 Axis CNC Router TB6560 Stepper Driver + Display + Control Pad + Aluminium Box Descriptions I. About the 3rd Generation ... moreTB6560 Stepper Controller Box This stepper controller box has been upgraded to an intelligent and industrial-level driver board set. The redesigned PCB board enables smoother control of motors. The totally enclosed optical isolation and bipolar constant-current chopper ensure a low noise& low vibration operation environment. Helping to avoid creeping at a low speed. Internally built manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& C
Buy It Now
Free Shipping Condition: New Location: United States 3PCS Wantai Stepper Motor Driver DQ860HA with 7.8A peak current ,24-80VDC ,256 Microstep，for Nema34 Wantai Stepper Motors. 1, Stepper Motor Driver DQ860HA. ... moreIt is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States Piece of 18AWG 4 leadDouble Shielded DS Flexion Robotics Grade Cable. DS Flexion 18awg Motor Retrofit Cable Kit. Here's an overview video of DS Flexion ... moreCable. DS Flexion Ultra Flex Double Shielded Robotics Cable Is Here!
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China For building a CNC machine, you need a lot of things. Such as Electronics Kit, Spindle Kit, Linear Motion Kit, and Gantry Kit. This3 Axis TB6600 Box Professional ... moreDriver Board is equipped with TB6600HG chip.
Buy It Now
$5.45 Shipping Condition: Used Location: San Jose, United States This is being sold AS IS with no accessories included unless specified or shown in the photos. Unless otherwise specifically agreed to in writing by the.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM542A 3 pcs Nema 23 stepper motor 425 oz.in bipolar with single shaft, 3.0A.
Buy It Now
$15.00 Shipping Condition: Used Location: Santa Clara, United States You will receive only what is in the picture.
Buy It Now
Free Shipping Condition: New Location: United States Phase Inductance (mH). 3 pcs Nema 23 stepper motor 270 oz.in 23HS8430. Nema 23 stepper motor. Step angle ( ° ). Phase Resistance ( Ω ). Lead Wire (NO.). ... moreGreat News from Longs motor! Motor Length L(mm).
Buy It Now
Free Shipping Condition: New Location: 金东区, China Stepper motor: X/Y1/Y2/Z. Connection: USB cable. 1 x USB cable. After the electrical connection is completed, turn on the power. The real color of the ... moreitem may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
Buy It Now
Free Shipping Condition: Used Location: Sacramento, United States It is also subject to change during peak periods. We take joy in helping you get the gear you want at the price you need. Power cord NOT included. We ... morework hard to include a lot of pictures of each item.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China QUALITY-GADGETS eBay Item! 3 Axis CNC Stepper Motor Driver TB6560 Box Set + LCD Display + Handle Controller Descriptions I. About the 3rd Generation TB6560 ... moreStepper Controller Box This stepper controller box has been upgraded to an intelligent and industrial-level driver board set. The redesigned PCB board enables smoother control of motors. The totally enclosed optical isolation and bipolar constant-current chopper ensure a low noise& low vibration operation environment. Helping to avoid creeping at a low speed. Internally built manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& Contr
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States Piece of 18AWG 4 leadDouble Shielded DS Flexion Robotics Grade Cable. DS Flexion 18awg Motor Retrofit Cable Kit. Here's an overview video of DS Flexion ... moreCable. DS Flexion Ultra Flex Double Shielded Robotics Cable Is Here!
Buy It Now
$15.95 Shipping Condition: New Location: Hoffman Estates, United States 2: 1pcs Gecko G540 4 axis stepper motor driver, Current Version. 3: 3 pcs NEMA23 381oz/in 3.5A Dual Shaft Stepper Motor KL23H2100-35-4B High-torque Nema ... more23 381 oz-in stepper motors. These are optimized for the G540 at 3.5A current.
Buy It Now
$10.00 Shipping Condition: New Location: China Handwheel Trial Processing: With. It is a new generation multifunctional CNC system for engraving, milling, drilling and tapping. Support carving, milling, ... moredrilling and tapping. It features 0.001 mm interpolation accuracy, the highest speed of 30 m/min.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States This kit features 3 of Gecko Drives G251x micro stepping drives that include. These cables are wired straight through for a simple universal " Plug N ... morePlay " solution to be used with your G251x drives that utilize a 4 lead connections ( This is also known as Bipolar ).
Buy It Now
Free Shipping Condition: New Location: 金东区, China Support software: Candle (3-axis); La ser GRBL (la ser). The toggle switch can switch XYY/XYZ axis work. Can be used on la ser engraving machines, drawer ... moremachines, CNC engraving machines, etc. Toggle to switch XYY/XYZ axis work, toggle the power switch, safe and efficient.
Buy It Now
$8.85 Shipping Condition: Used Location: Haverford, United States Advantech PCL-839 Rev.A1 3-Axis Stepping Motor Control Card 16-Bit ISA with DB37 USED. WORKING | AUCTION TERMS: 30-day DOA ITEM DESCRIPTION: You are buying ... morea used. Working. Advantech PCL-839 Rev.A1 3-Axis Stepping Motor Control Card 16-Bit ISA wtih DB37 Cable and Wiring Board Main Features: Independent. Simultaneous control of three stepping motors Optically-isolated outputs Five isolated digital inputs per axis for limit switches Half-size PC add-on card Up to 200 kpps step rate 16 x DI/O. This item has been removed from a working environment and tested by a qualified technician. You will received this item as pictured. No cables or accessories other than those mentioned or pictured in the listing will be included. 30-Day Warranty! ITEM PICTURES: PAYMENT: WE ACCEPT PAYPAL. ALL CREDIT CARD PAYMENTS MUST BE MADE THROUGH PAYPAL! IF YOU NEED TO SEND US A NOTE OR A MESSAGE DURING CHECKOUT. PLEASE DO NOT US ADD NOTE IN THE CHECKOUT PART OR IN PAYPAL. INSTEAD SEND US A MESSAGE THROUGH EBAY OR EMAIL US DIRECTLY! WE RESERVE THE RIGHT TO DENY ANY PAYMENT THAT WE CONSIDER FRAUDELENT OR SUSPICIOUS! shipping: PLEASE NOTE THAT FREE SHIPPING OPTION IS NOT AVAILABLE TO ALASKA. HAWAII AND US TERRITORIES AND IN MOST CASES THERE IS GOING TO BE A SURCHARGE. BUYERS FROM ALASKA. HAWAII AND US TERRITORIES PLEASE CHOOSE USPS PRIORITY MAIL INSTEAD OF THE FREE SHIPPING OPTION. ALL PACKAGES WILL BE SHIPPED THE FOLLOWING BUSINESS DAY AFTER THE PAYMENT IS CLEARED VIA FEDEX GROUND. USPS PARCEL POST OR USPS FIRST CLASS WITH TRACKING INFORMATION UNLESS EXPEDITE OR INTERNATIONAL SHIPPING IS REQUESTED. PLEASE NOTE. ALL UPS QUOTED RATES WOULD BE SUBSTITUTED FOR EQUIVALENT FEDEX SERVICE UNLESS REQUESTED OTHERWISE. SHIPPING COST IS FIXED FEE. NON-NEGOTIABLE AND NON-REFUNDABLE. IT INCLUDES PACKING MATERIAL COSTS AND HANDLING EXPENSES. ANY MERCHANDISE SENT TO ANOTHER COUNTRY MAY BE SUBJECT TO DUTY UNDER THE CUSTOMS REGULATIONS OF THAT COUNTRY. TECHYPARTS. LLC. DOES NOT MAINTAIN OR PROVIDE INFORMATION CONCERNING THE ASSESSMENT OF CUSTOMS DUTY. CARRI
Buy It Now
$5.00 Shipping Condition: New Location: China 1 x 3-Axis TB6560 Stepper Motor Driver. - Universal architecture: Supports most parallel software MACH3, KCAM4, EMC2 etc! - Adjustable drive current settings ... morefor each axis: 25%,50%,75%,100% of full current can be set for different stepper motors.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver--DM860A Stepper motor driver DM860A.
Buy It Now
$10.00 Shipping Condition: New Location: China (12) Support XHC series of wireless electronic mach3 MPG, such as WHB04 MPG. 1) Support all versions of Mach3 (can't work with Mach4). Under Mach3 working ... morestate, USB cable unplugs and then plugs in, but also the normal connection.
Buy It Now
$3.99 Shipping Condition: New Location: China Axis: 1, 2, 3 or 4 (X, Y, Z, C). X, Y, Z, C axis can conduct linear interpolation, X, Y can do circular interpolation. Count: When this command is executed, ... morethe number on the main interface and manual interface will increase by 1 or decrease by 1.
Buy It Now
$5.00 Shipping Condition: New Location: China Press Z+ and Z-, the Z axis will move up and down. - Press X+ and X-, the X axis will move left and right. - Press Y+ and Y-, the Y axis will move Front ... moreand Back. We are the trustworthy supplier.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Ship from German warehouse! 3AXIS Nema34 Stepper Motor 1600oz-in 3.5A& driver CNC Router or Mill Great News for European customers! Our products are ... moreshipped from German warehouse directly. after payment. Within 3 ~5 business days for receiving products! Easy to custom clerance, no damage, better service, please don't hesitate! What's in Box? 3 PCS Nema 34 Stepper Motor with Single shaft 1600oz-in holding torque, 3 PCS Stepper Driver DM860A with 7.8A replacing MD882, 3PCS Power Supplies for 35 0W.60VDC, 1 PC Breakout Board, 1 PC DB25 Cable 1.Nema 34 stepper motor: Model Step angel( °) Motor Length L(mm) Rate Voltage(V) Rate Current(A) Phase Resistance( Ω) Phase Inductance(mH) Holding Torque(oz.in) Lead Wire(NO. Rotor Inertia(kg. c? Motor Weight(kg) 34HS5435C-37B2 1.8 151 5.7 3.5 1.9 22 1600 4 3.6 5 2.Stepper motor driver: Detailed pic: Technical Specification: 1. Stepper motor driver DM860A: Http:www.longs-motor.com/ProductsView.asp?id=273&pid=83 Introduction: DM860A is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 8.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: L High performance. Low price. L Average current control. 2-phase sinusoidal output current drive. L Supply voltage from 24VDC to 80VDC. L Opto-isolated signal I/O. L Overvoltage. Under voltage, overcorrect, phase short circuit protection. L 14 channels subdivision and automatic idle-current reduction. L 8 channel
Buy It Now
Free Shipping Condition: New Location: United States This item includes: 3 PCS Nema 17 with 4000g.cm. 1.7A current, 4-Leads, 40mm body length, 5mm shaft diameter, 2 phase, 3 PCS DQ420MA with 1.7A peak current. ... more12-36VDC, 128 Microstep 1 PC 200W.24VDC,8.3A Power Supply, 1 PC Breakout board Board& Cable 1. Stepper Mo tor Technical Specifications Part No. 42BYGHW609 Frame Size: NEMA17 Step Angle: 1.8 degree Voltage: 3.4 V Current: 1.7 A/phase Resistance: 2.0 Ohm/phase Inductance: 3.0 mH/phase Holding torque: 4000 g-cm 56 OZ-IN Rotor inertia: 54 g-cm2 Detent torque: 0.22 kg-cm Number of wire leads: 4 Weight: 0.24 kg Length: 40 mm Motor Shaft: 5mm Front Shaft length: 20mm We offer customer's designed service! If you need special size. Please offer us your size requirements, so that we can manufacturer the exact models for you, thanks: 2. Matching Stepper Motor Driver DQ420MA with 1.7A,12-36VDC/128Microstep. http:www.wantmotor.com/ProductsView.asp?id=273&pid=82 Introduction: DQ420MA is a type of two-phase hybrid stepping motor driver. The drive voltage of which is from 12VDC to 36VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 20mm to 42mm outside diameter and less than 2.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor to run smoothly almost without noise and vibration. Holding torque when DM420A rund at high speed is also significantly higher than the other two-phase drivers, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features: l High performance. Low price l Average current control. 2-phase sinusoidal output current drive l Supply voltage from 12VDC to 36VDC l Opto-isolated signal I/O l Overvoltage. Under voltage, overcurrect, phase short circuit protection l 8 channels subdivision and automatic idle-current reduction l 8 channels output phase current setting l Offline command input termina
Buy It Now
Free Shipping Condition: New Location: United States Cnc Kit 3 Axis Tb6560 Stepper Motor Driver Mill Router Nema 23 Motor 24V10A Psu Hi. You are bidding a GREAT VALUE 3 AIXS CNC PC CONTROL COMPLETE KIT! ... morePackage includes: 1 x New 3 Axis TB6560 Driver Controller Board 1/16Microstep. 12-36V, 1.5A-3A 3 x New 57BYGH56-401A Single-Shaft Stepper Motors 1.26Nm/175oz-in 2.8A 1 x New 24V 10A power supply Product Features: Toshiba TB6560AHQ chip- High power. Maximum 3.5A drive current chipset. 1-1/16 microstep setting- Higher accuracy and smoother operation than standard 1. 1/2 step. Adjustable 1.5A-3A drive current settings for each axis- 25%50%75%100% of full current can be set for different stepper motors. Overload. Over-current and over-temperature safety- Full protection for your computer and peripheral equipment. On board current switching- Power output can be set according to specific user requirement. Full closed-type optical isolation to protect the user's computer and equipment. Relay spindle interface- Outputs Max. 36V 7.5A for spindle motors or coolant pump(only one device can be powered by this output! 4 channel inputs interface- Can be used for XYZ limit and emergency stop. Professional design- Two stage signal processing with super anti-jamming. Bipolar constant current chopper drive with non-resonant region- Controls motors smoothly through range without creep effect. Four-input Control; Allow setting the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment. Universal architecture- Supports most parallel software MACH3.KCAM4 etc. For compatibility with other softwares. Please feel free to contact us. Dip settings: Current Setting 1 2 Decay Mode Settings 3 4 MicroStep Settings 5 6 100% ON, ON, FAST, ON, ON, 1, ON, ON, 75% ON, OFF, 25% ON, OFF, 1/2, ON, OFF, 50% OFF, ON, 50% OFF, ON, 1/8, OFF, ON, 25% OFF, OFF, SLOW, OFF, OFF, 1/16, OFF, OFF, Further Details: Power supply DC 12-36V*The stepper motor directly gets the power from the stepper driver. It doesn't require a separate power source. Voltage Selection: 12-16
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China For Windows: All Mach3 CNC. 1x 4 Axis Wireless Mach3 MPG Pendant CNC Handwheel. (batteries are NOT included). - Maximum axis: 4 axis. Wireless MPG,install ... more2AA batteries,turn on the power switch,you can mormally use.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China CNC Router Lathe 3Axis TB6600HG Stepping Motor Driver 0.2-5A Gcode Recorded&Box Description I. About the 3rd Generation TB6600HG Stepper Controller ... moreThis TB6600HG Stepper Controller has all the functions of TB6560AHQ Stepper Controller. And is specially developed for stepper motors with higher currents. All the 2 or 4 phase Nema17/23/24/34 stepper motors with current range of 0.2A~5.0A work perfectly with this TB6600HG Stepper Driver. It has standard version and professional version to meet different user needs. For further information. Please click on the following links. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Aluminum housing protection, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This stepper driver can easily record MAXIMUM 3 Axis' X.Y,Z Axis) G-code running i n the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. on the computer, after which you can run motors using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) can not only be used for manual motor control. But also manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you can easily run motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 3 Axis Professional Version(TB3H-CD-P(Box) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions& Specifications Display Panel& Control Panel Features High performance. Cost-effective; Manual motor control via control panel; s
Buy It Now
Free Shipping Condition: New Location: China 3 Axis Nema 34 stepper motor 1600 oz.in & Driver &Power. 3 pcs Nema 34 stepper motor 1600 oz.in bipolar with single Shaft. Nema 34 stepper motor Hording ... moretorque when DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 3 pcs Nema 34 stepper motor with dual shaft, 1600oz. in, biloar. 3 pcs Stepper motor driver, peak 7.8A 24-80VDC. Nema 34 stepper motor Hording torque ... morewhen DM860A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China • Compatible with the Mach2, Mach3(Default Software), LinuxCNC(EMC2), KCAM4 CNC Software, etc. This function is widely applied in RBI machine, Conveyor ... moreetc. EMA342-7842S4 Nema34 Stepper Motor. Stepper motors and drivers from ENGMATE.
Buy It Now
Free Shipping Condition: New Location: United States 3 PCS Wantai Stepper Driver DQ860MA with 80VDC,7.8A, 256 Microstep. The DQ860MA is an economical microstepping driver based on patented technology of ... moreWantai Motor. It is suitable for driving 2-phase 4-phase hybrid stepping motors.
|
|
|
 |