|
Order by:
Available to:
eBay Affiliate Links
|
Buy It Now
$18.51 Shipping Condition: Used Location: Oxford, United States Resistive 278VA.
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: New Location: China Monitoring Circuit: L1, L2, L3. High-Capacity 2600mAh Drone Battery for E88 E525 E99 K3 RC Quadcopter. USB 1.44MB Floppy Drive Emulator for Music Keyboards ... moreKorg GoTek. 20Pcs 2mm Brass Banana Plug Male Connector Set Kit for Electronics DIY.
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED.
Buy It Now
Free Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Display mode: LCD displays eachActions status. The real color of the item may be slightly different from the pictures shown on website caused by many ... morefactors such as brightness of your monitor and light brightness.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED.
Buy It Now
Free Shipping Condition: Used Location: Bhavnagar Wadva S.O, India Id no.: 890220. phasenfolge/ phasenausfallrel/ phase sequence /phase failure relay. We are here to help and will do our best to resolve any issues. dc1: ... more24v 5,0a. dc13: 24 v 1,5a.
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.60 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.60 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$3.92 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.60 Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
$3.92 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
$0.67 Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
$0.61 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
$0.60 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
$3.92 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Your best online store electrical products, Description, It's brand new. Good qu ali t y& high perf ormance New TL 2238 Phase Failure Phase Sequence ... moreProtect Relay 220~380VAC 460-660VAC 50Hz/60Hz QUANTITY:1PCS A.Characteristics of protection: 1.Phase loss protection: It means that any phase occurs phase loss when the protected circuit is in running or stopping status. In this case. The red indicator light will be lighted and be priority. 2. Phase opposite protection: It is a safeguard acting immediately. Which protects L1, L2, and L3 three phase against wrong connection sequence. In this case, the yellow indicator light will be lighted. 3. Voltage imbalance protection: While a protection of voltage imbalance rate 8% The imbalance of three phase voltage will affect the safe running of the equipment. In this case that there is a phase losing, the red indicator light will be lighted and be priority. 4. Delay protection: When the fault happens. The monitor will delay 1~2 seconds to act and release. B. Characteristics of performance: 1. The protection functions of relay don’t be affected by current intensity of circuit or load. Impulse current, imbalance current and load characteristic. The relay could long term work under full capability and full climate. Power consumption is lower than 2W. C. Characteristics of working: 1.If the connection of L1. L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light of the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally. In this case that there occurs yellow light illuminated and relay unclosed after the protected equipment works normally, it should be a wrong connection of external circuit. The relay has a function of protection against wrong connection. 2. While any of these L1. L2 and L3 phases is Na phase, the red light is lighted with the unlighted green light and the released relay. While the voltage come back to normal, it will rec
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
$0.67 Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED. ... moreTemperature fluctuation error: 0.05%/°C, at=20°C.
Buy It Now
$0.71 Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
Free Shipping Condition: Brand New Location: China If the connection of L1, L2 and L3 phases are right, the green light of the relay illuminates and the relay closes. If they are wrong, the yellow light ... moreof the relay illuminates. Exchanging any two of them, the relay will accept the phase sequence and begin to work normally.
Buy It Now
Free Shipping Condition: New Location: 金东区, China 2 reset modes available: automatic reset, manual reset. Reset mode: automatic/manual. Reset delay: 0.1-999s. Power on delay function. Unbalanced delay: ... more0.1-999s. Power on delay: 0-999s. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
Buy It Now
Free Shipping Condition: New Location: 金东区, China 2 reset modes available: automatic reset, manual reset. Reset mode: automatic/manual. Reset delay: 0.1-999s. Display mode: LCD displays eachActions status. ... moreThe real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED.
Buy It Now
Free Shipping Condition: Brand New Location: China Phase sequence protection: Yes. Relay working status is indicated by LED indicators. Phase failure protection: Yes. Output relay indication: Red LED.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Power on delay function. The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness ... moreof your monitor and light brightness. Power on delay: 0-999s.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Display mode: LCD displays eachActions status. The real color of the item may be slightly different from the pictures shown on website caused by many ... morefactors such as brightness of your monitor and light brightness.
|
|
|