|
|
Order by: Available to: This site contains affiliate links for which I may be compensated
|
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 521500 NEW Air Oil Filter Compressor IR GD Atlas Copco Comp Air 521500 GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 6241271900 NEW Air Oil Filter Compressor IR GD Atlas Copco Worthington GSI Industrial 621-721-1634 Questions Please Call In the compressor system. The ... moreoil itself must be filtered on a regular cycle so as to remove contaminants that may enter the compressor and damage the unit. This is accomplished through the installation of a lube oil filter, either in cartridge, or spin-on form, which then ensures that all of the oil is cleaned as it moves through the filter. Filtering in 5-25 micron range(depending upon application) it is again. The depositing of oil-borne contaminant over time(similar to the oil-separator) that causes the oil filter to continually increase in differential pressure to a point at which it must be replaced in order to continue proper filtration of the compressor oil. Like all of our products. GSI oil filters are built of the highest quality materials and workmanship. Specific filtration levels are obtained through the exclusive use of high grade filter media and consistent surface area control, obtained by a strict maintenance of pleat quantity and depth. Leakages are prevented by the positive seals obtained with both plastisol and epoxy encapsulation. Viton seals are used where applications of synthetic oil are typical. A B C Part No. Capacity(gallons/liters/min. Thread OD inches/ mm Length inches/ mm GS100 2.17/ 12.00 3/4- 16 3.15/ 80.00 3.66/ 93.00 GS200 5.00/ 20.00 3/4- 16 3.15/ 80.00 5.50/ 140.00 GS300 10.50/ 40.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS400 10.50/ 40.00 3/4- 16 3.78/ 96.00 5.50/ 140.00 GS500 10.50/ 40.00 1- 12 3.78/ 96.00 5.50/ 140.00 GS600 11.89/ 45.00 1- 12 3.78/ 96.00 6.77/ 172.00 GS700 18.50/ 70.00 1- 12 3.78/ 96.00 8.30/ 210.00 GS800 18.50/ 70.00 1- 12 4.33/ 110.00 8.94/ 227.00 GS900 47.50/ 180.00 1-1/2-16 5.50/ 140.00 11.69/ 302.00
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Gardner Denver air compressor. Model EAU 99P ( 296 mm shaft size). Evaluation and diagnosis ... moreof your airend condition during disassembly.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States R-28875 Separator Air Oil Filter Compressor GD R- 28875 Bauer IR Quincy GSI Industrial 621-721-1634 Questions: Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar, Pressure resistance(against collapse) 70 psi/ 5.0 bar, Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3, Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination, Bonding compound- polyurethane or epoxy, Body components- corrosion resistant steel, Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States QA 100/125/150, QA200, QA300, QMA 50/60, QMA 75/100, QMA 125/150, QMB 10/25, QMT 10/25, QSB 15-50, QSF 50/60, QSF 75/100, QSF 125/150, QSI 30, QSI 150, ... moreQSI 200/300, QSI 220/245/370, QSI 235/350, QSI 440/500/675/750, QSI 490/740, QSI 1000/1250/1500, QST 15-40, QST 25-40, QSVB 7.5-25, QSVI 20/40/50, QSVI 75/100, QSVI 200, QXB 7/15, QXT 7/15.
Buy It Now
$850.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 20HP VSD Rotary Screw Air Compressor Bundle Ingersoll Rand Filter 20 VARIABLE SPEED DRIVE VFD. The GS rotary screw compressor is designed for a ... morecontinuous duty operation. All units are fully enclosed with a cabinet for a low sound level.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 2236.1060-27 Separator Air Oil Compressor Screw CPT 2236106027 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential in ... moremany industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 2118520 Separator Air Oil Compressor Screw Co.Aire Champion 2118520 Co Air GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is ... moreessential in many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 2812476 Separator Air Oil Compressor Screw 2812476 C Reemers GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential in ... moremany industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We rebuild your existing SULLAIR VS 20 60-75 MODEL AIREND REBUILD FOR AIR COMPRESSOR (204 MM SHAFT SIZE). Evaluation and diagnosis of your airend condition ... moreduring disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States AS2451 Separator Air Oil Compressor Screw AS 2451 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential in many industries ... morefor its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. XGSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6100-6125 MODEL (178MM SHAFT). Evaluation and diagnosis of your airend ... morecondition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We rebuild your existing SULLAIR 20A 100-150L/H MODEL AIREND REBUILD FOR AIR COMPRESSOR (204 MM SHAFT SIZE). Evaluation and diagnosis of your airend condition ... moreduring disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We rebuild your existing LEROI AIR COMPRESSOR MODEL A50SS ( 175 MM SHAFT SIZE). Evaluation and diagnosis of your airend condition during disassembly. ... moreWe will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$625.00 Shipping Condition: New Location: Minneapolis, United States Up for sale is a good used Gast Model 2HBC-10-M200X oil-less twin piston 120 vac 1/4 hp air compressor pump. The pump is in good working condition. The ... morefan shrou d covering the fan blade has a portion of it broken off. The fan is intact and working good. Please view the pictures for the condition. Cable Pressurization Dry Sprinkler Fire Protection Tire Inflators Air Suspension Beverage Dispensing Pneumatic Temperature Controls Door Closures Power Spraying Spray Painting Medical/Dental Clinics
Buy It Now
$625.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 10HP Screw Air Compressor. The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet ... morefor a low sound level. GS COMPRESSOR. Fan is mounted on the cooler to allow operation of compressor with side panels off.
Buy It Now
$10.00 Shipping Condition: New Location: Minneapolis, United States 2236105790 Separator Air Oil Compressor Screw CPT 2236.1057-90 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential in ... moremany industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 91108-012 Separator Air Oil Compressor Screw Flottman Fusheng 91108- 012 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$850.00 Shipping Condition: New Location: Minneapolis, United States Capacity 256@ 100 psi Sound Level DBA 65 DBA Cooling Air/Oil Weight 2336 LBS Dimensional(L-W-H) 59” x 38” x 56” Operating Pressure 60-175psi Controls ... moreOn/Off Dual Control Voltages 200– 575(Please specify) GSI Inc. 612-721-1635 Please call with any question. The GS-60 Series Air compressor is a single stage. Air cooled, oil injected rotary screw air compressor package. The compressor package includes the rotary screw compressor, main drive motor, air and oil system, filters, oil cooler, cooling fan and controls. The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. The Compact design requires a minimum amount of space with an extremely low noise level for.ease of placement in any facility. General Technical Information. All Voltages Available, Wye-Delta Start for low power consumption is standard, Air inlet and particle filters are standard, Integrated cooling system, Air and Oil Lines are copper and Stainless steel braided, Separation System. Multi-Stage Ail/Oil Air separator filter system. ASME and CRN approved safety valve. Air/Oil separator reservoir tank with oil level sight glass. Easy oil drain excess. Air Control. Certified with a CE listed electrical components. Drive System. Integrated V-Belt system plus easy tension system. AirEnd. German engineered high efficiency male and female rotor design, Oil injected during compression stage for lubrication and sealing, State of the art air/oil temperature sensor at discharge of compressor. Cooler. Plate fin air cooled aluminum oil cooler which is cooled by a dedicated cooling fan. Oversized cooling capacity allows for simple operation at high ambient temperatures. Fan. Fan is mounted on the cooler to allow operation of compressor with side panels off. Electric Motor. High efficiency motor meeting NEMA requirements. Foot/Flange mounted motor frame. TEFC(Totally enclosed fan cooled) to protect motor providing longer life. Special winding Coating for longer lif
Buy It Now
$625.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 10HP Rotary Screw Air Compressor Bundle Ingersoll Rand Filter 10. The GS rotary screw compressor is designed for a continuous duty operation. All ... moreunits are fully enclosed with a cabinet for a low sound level.
Buy It Now
$850.00 Shipping Condition: New Location: Minneapolis, United States The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. NEW GS ... more25HP Rotary Screw Air Compressor. Separation System.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 1039210030 Separator Air Oil Compressor Screw Termomeccanica 1039210030 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$950.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 50HP VSD Rotary Screw Air Compressor Bundle Ingersoll Rand Filter VARIABLE SPEED DRIVE VFD. The GS rotary screw compressor is designed for a continuous ... moreduty operation. All units are fully enclosed with a cabinet for a low sound level.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 6221347900 Separator Air Oil Compressor Screw Worthington 6221347900 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6200-6250C (CN6) MODEL. Evaluation and diagnosis of your airend condition ... moreduring disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 4101.5102.2 Separator Air Oil Compressor Screw Flottman 4101. 5102. 2 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States CK4076-335 Separator Air Oil Compressor Screw CompAir CK 4076- 335 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. XGSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Champion EW 75 (SHAFT SIZE 160). Evaluation and diagnosis of your airend condition during ... moredisassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor CRS 40-50E MODEL. Evaluation and diagnosis of your airend condition ... moreduring disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6150-6200 MODEL. Evaluation and diagnosis of your airend condition during ... moredisassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$850.00 Shipping Condition: New Location: Minneapolis, United States The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. GS COMPRESSOR. ... moreFan is mounted on the cooler to allow operation of compressor with side panels off.
Buy It Now
$950.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 50HP VSD Rotary Screw Air Compressor Bundle Ingersoll Rand Filter VARIABLE SPEED DRIVE VFD. The GS rotary screw compressor is designed for a continuous ... moreduty operation. All units are fully enclosed with a cabinet for a low sound level.
Buy It Now
$950.00 Shipping Condition: New Location: Minneapolis, United States The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. NEW GS ... more50HP Rotary Screw Air Compressor Pump A IR END 50 hp Industrial.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Champion EW 40-60 (SHAFT SIZE 160). Evaluation and diagnosis of your airend condition during ... moredisassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6060-6075 MODEL (127MM SHAFT). Evaluation and diagnosis of your airend ... morecondition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6100-6150C (CN5) MODEL (204 MM SHAFT). Evaluation and diagnosis of your ... moreairend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor CRS 100-125 MODEL. Evaluation and diagnosis of your airend condition ... moreduring disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We rebuild your existing LEROI AIR COMPRESSOR MODEL WE100SS ( 175 MM SHAFT SIZE). Evaluation and diagnosis of your airend condition during disassembly. ... moreWe will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$950.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 50HP Rotary Screw Air Compressor Pump A IR END 50 hp Industrial. The GS rotary screw compressor is designed for a continuous duty operation. All ... moreunits are fully enclosed with a cabinet for a low sound level.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Ingersoll Rand air compressor. PA 40-60, PA 75-100, PA 100-125, PA 125-150, PA 150-300, ... more50 HSP/HHSP/LSP, 60 HSP/HHSP/LSP, 75-100 HSP/HHSP/LSP, 100L-150HH, 200L-250H, 300L-500L, 500H-800L, 1000L-1500H, 1600L-3000L, EP/HXP/XP 5-10, EP 10-15ESP, EP15-25SE, EP25-50SE, EP/HP/XF 25-50, XFE 50, EP/HP/XF 60, EP/HP/XF 75-100, EP/HP/XF 125-200, EP/HP/XF 250-300, EPE/HPE/XFE 300, EP/HP/EF 350-450, EPE 100-200S2, EPE 250-450S2, U 10-25HSP, U 25-40HSP.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor CRS 50-75 MODEL. Evaluation and diagnosis of your airend condition during ... moredisassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$725.00 Shipping Condition: New Location: Minneapolis, United States The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. NEW GS ... more15HP Rotary Screw Air Compressor Pump A IR END 15 hp Industrial.
Buy It Now
$625.00 Shipping Condition: New Location: Minneapolis, United States NEW GS 10HP Rotary Screw Air Compressor. NO SERVICE CONTRACT.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6060-6100C (CN4) MODEL (160MM SHAFT). Evaluation and diagnosis of your ... moreairend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 7211960000 Separator Air Oil Compressor Screw Elgi Fiac 721196 0000 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$850.00 Shipping Condition: New Location: Minneapolis, United States The GS rotary screw compressor is designed for a continuous duty operation. All units are fully enclosed with a cabinet for a low sound level. Separation ... moreSystem. GS COMPRESSOR. Plate fin air cooled aluminum oil cooler which is cooled by a dedicated cooling fan.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 1311127500 Separator Air Oil Filter Compressor Screw IR Atlas Capco GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar, Pressure resistance(against collapse) 70 psi/ 5.0 bar, Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3, Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination, Bonding compound- polyurethane or epoxy, Body components- corrosion resistant steel, Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States We will Rebuild your rotary screw oil-flooded airend for your Comp-AIr Compressor 6015-6030C MODEL (112MM SHAFT). Evaluation and diagnosis of your airend ... morecondition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory specifications.
Buy It Now
$250.00 Shipping Condition: Seller refurbished Location: Minneapolis, United States Evaluation and diagnosis of your airend condition during disassembly. We will inform you if any machining is necessary to bring your Airend up to factory ... morespecifications. The Airend must be free moving and turnable.
Buy It Now
$15.00 Shipping Condition: New Location: Minneapolis, United States 72119630000 Separator Air Oil Compressor Screw Elgi Fiac 7211963 0000 GSI Industrial 621-721-1634 Questions Please Call Compressed air and gas is essential ... morein many industries for its use in equipment operation. Instrumentation, refrigeration and a variety of industrial processes. Clean, oil-free air or gas is a requirement to reduce maintenance and replacement costs. Unfortunately, even atmospheric air contains objectionable contaminants, in both solid and liquid forms, that must be removed prior to the use of the compressed gas. Additionally, in many compressor and vacuum packages, oil is intentionally introduced as a coolant and sealant which must also be taken out prior to air use. GSI manufactures a wide range of air-oil separators for air compressors and vacuum packages. As well as air inlet, oil and coalescing type filters, that when used together, provide the ultimate in system operation and protection. GSI oil separators operate on the familiar principles of fine liquid droplet coalescence in a flowing stream. These processes have been refined and tailored into packages that meet the special high performance and physical requirements of the air/gas compressor industry. Regardless of style(conventional. Pleated or deep) GSI oil separators will provide performance as shown here: Pressure drop(at load) 2-3 psi/ 20 bar Pressure resistance(against collapse) 70 psi/ 5.0 bar Efficiency(remaining oil in gas stream) 2-3 ppm/ 2-3 mg/m3 Operating Temperature: standard) 180° F/ 82° C to 230° F/ 110° C(higher temperature models available) Materials: Media- both wet laid and high loft solely or in combination Bonding compound- polyurethane or epoxy Body components- corrosion resistant steel Service life: Dependant mainly upon the cleanliness of the oil and gas being compressed as well as the initial amount of oil contained in the gas stream; several thousands of hours of operation are possible in a well-functioning compressor or vacuum system. 336.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B
|
|
|
|