Buy It Now
$26.97 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is one of the most commonly used Low Carbon Content Steels. The steel has good hardening properties, fair machinability and is easy to ... moreweld. Good for applications that do not require high strength.
Buy It Now
$11.79 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$16.23 Shipping Condition: New Location: South Hackensack, United States O-1 Oil Hardening. Deep hardening characteristics and fine grain structure. Temperature of the quenching oil should be 120°-140°F for best results. Do ... morenot quench in water because this is an oil hardening steel.
Buy It Now
$60.82 Shipping Condition: New Location: Tolland, United States All available as standard or oversize. In house Blanchard Grinding to 60" and Surface grinding to 120". All sizes of 1018 Cold Finished Bar.
Buy It Now
$28.42 Shipping Condition: New Location: Tolland, United States Typical Analysis; Carbon. 38% -.43%, Manganese 0.75-1.00%, Chromium. 80%-1.10%, Molybdenum. 15%-.25% Typical applications include; Spindles, Rods, Shafts, ... moreStuds, Axles, Arbors, Gears, Machine Parts, Inexpensive Tooling, Short Run Stamping Dies.
Buy It Now
$23.67 Shipping Condition: New Location: Tolland, United States Used for shafting applications where a higher tensile is needed than low carbon steels and machining is required. For Sale:A Bundle Of 5 Pieces;. O-1, ... moreA-2, D-2, S-7, 4142PH, A-6, M-2, Low Carbon and other grades.
Buy It Now
Free Shipping Condition: New Location: Ferndale, United States Deep hardening characteristics and fine grain structure. Material Type: O-1 Standard. FREE Standard. Weight (lbs): 3.82.
Buy It Now
$14.91 Shipping Condition: New Location: STOCKPORT, United Kingdom DLC Diamond Like Carbon Coating can provide up to 100% increase in tool life, edge honed flutes decrease cutting forces and are excellent in finishing ... moreoperations. Can be used for dry cutting. High performance variable, unequal 38-42° helix with lapped flutes.
Buy It Now
$21.32 Shipping Condition: New Location: Tolland, United States Also available in a full range of other sizes - lengths & Surface Conditions INCLUDING 4140 CF Annealed / 4140 HR Annealed and 4140 TGP Heat Treated. ... moreIf you make tools, molds, gages, dies, shafts, or machine parts this is a good to have around.
Buy It Now
$12.80 Shipping Condition: New Location: Tolland, United States This piece was produced by Starrett and one side of piece was Line Marked by Starrett with Blue paint. O-1, A-2, D-2, S-7, 4140 Annealed / 4142PH, A-6, ... moreM-2, Low Carbon and other grades. All available as standard or oversize.
Buy It Now
Free Shipping Condition: New Location: Singapore Part Number: YY36HA20A. Item ID: 24765. If there are more than (1) quantity, do feel free to reach out to us for an actual image of each unit. We also ... moredo not price match against sites with on-going flash sales.
Buy It Now
$22.27 Shipping Condition: New Location: Tolland, United States Typical Chemistry Composition; Carbon. 43% -. 50%, Manganese. 60% -. 90%, Phosphorus. 040% Max, Sulfur. 050% Max.,1045 Is used by many industry sectors ... morefor a wide variety of applications including pins and rolls, studs, shafts, spindles etc.
Buy It Now
$36.47 Shipping Condition: New Location: Tolland, United States Typical Analysis; Carbon. 38% -.43%, Manganese 0.75-1.00%, Chromium. 80%-1.10%, Molybdenum. 15%-.25% Typical applications include; Spindles, Rods, Shafts, ... moreStuds, Axles, Arbors, Gears, Machine Parts, Inexpensive Tooling, Short Run Stamping Dies.
Buy It Now
$26.64 Shipping Condition: New Location: Tolland, United States 303 stainless steel turned, ground and polished to fit in standard bearings. Austenitic, non-magnetic stainless steel has good corrosion resistance, heat ... moreresistance and machinability. Conforms to ASTM A484 and A582.
Buy It Now
$18.59 Shipping Condition: New Location: South Hackensack, United States O-1 Oil Hardening. Deep hardening characteristics and fine grain structure. Temperature of the quenching oil should be 120°-140°F for best results. Do ... morenot quench in water because this is an oil hardening steel.
Buy It Now
$12.80 Shipping Condition: New Location: Tolland, United States Used for shafting applications where a higher tensile is needed than low carbon steels and machining is required. O-1, A-2, D-2, S-7, 4142PH, A-6, M-2, ... moreLow Carbon and other grades. All available as standard or oversize.
Buy It Now
$11.79 Shipping Condition: New Location: Tolland, United States S-7 Tool Steel is an air-or oil-hardening tool steel with a nice combination of exceptional toughness and wear resistance properties. S-7 is an excellent ... morechoice for blanking and die forming applications, as well as applications needing shock and impact resistance tools.
Buy It Now
$11.79 Shipping Condition: New Location: Tolland, United States Width and Length are Saw Cut Nominally Oversize Approx +1/16" / +1/8". Thickness is either Ground OR Milled, Approx +.015" / +.045" Oversize. All available ... moreas standard or oversize. A-2 Tool Steel Decarb Free Annealed Plate; 1 Piece; 7/8" Thick X 1" Wide X 12" Length.
Buy It Now
$12.80 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$10.96 Shipping Condition: New Location: Tolland, United States Width and Length are Saw Cut Nominally Oversize Approx +1/16" / +1/8". Thickness is either Ground OR Milled, Approx +.015" / +.045" Oversize. All available ... moreas standard or oversize. A-2 Tool Steel Decarb Free Annealed Plate; 1 Piece; 1/4" Thick X 1-3/4" Wide X 12" Length.
Buy It Now
$10.96 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$15.48 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$12.80 Shipping Condition: New Location: Tolland, United States 4140 Decarb Free Heat Treated / Pre-Hard Plate; 1 Piece; 1/2" Thick X 2-1/4" Wide X 12" Length. 4140 Round Bar also available in a full range of other ... moreSizes, Lengths & Surface Conditions Including HR Annealed, HR Heat Treated and TGP Heat Treated.
Buy It Now
$27.52 Shipping Condition: New Location: Tolland, United States Used for shafting applications where a higher tensile is needed than low carbon steels and machining is required. O-1, A-2, D-2, S-7, 4142PH, A-6, M-2, ... moreLow Carbon and other grades. All available as standard or oversize.
Buy It Now
$12.80 Shipping Condition: New Location: Tolland, United States Typical Analysis; Carbon. 38% -.43%, Manganese 0.75-1.00%, Chromium. 80%-1.10%, Molybdenum. 15%-.25% Typical applications include; Spindles, Rods, Shafts, ... moreStuds, Axles, Arbors, Gears, Machine Parts, Inexpensive Tooling, Short Run Stamping Dies.
Buy It Now
$25.41 Shipping Condition: New Location: Tolland, United States Also available in a full range of other sizes - lengths & Surface Conditions INCLUDING 4140 CF Annealed / 4140 HR Annealed and 4140 TGP Heat Treated. ... moreIf you make tools, molds, gages, dies, shafts, or machine parts this is a good to have around.
Buy It Now
$46.60 Shipping Condition: New Location: Tolland, United States Carbon Steel Grade 12L14 Cold Finished Leaded, 1 Piece; 2" Hexagon X 36" Length. 12L14 gives a smooth, machined surface and because of its low friction ... morecomponent allows for increased tool life. As material has a Lead additive [.15/.35] it cannot be welded.
Buy It Now
$20.00 Shipping Condition: New Location: Tolland, United States Is a free machining quality which generally will result in a smooth, bright finish. Typical Chemistry Composition; Carbon. 09% Max, Manganese. 75% - 1.05%, ... morePhosphorus. 040% -. 090%, Sulfur. 26% -. 35% Due to it's free machining characteristics it is poor to weld.
Buy It Now
$28.42 Shipping Condition: New Location: Tolland, United States Also available in a full range of other sizes - lengths & Surface Conditions INCLUDING 4140 CF Annealed / 4140 HR Annealed and 4140 TGP Heat Treated. ... moreIf you make tools, molds, gages, dies, shafts, or machine parts this is a good to have around.
Buy It Now
$18.59 Shipping Condition: New Location: South Hackensack, United States O-1 Oil Hardening. Deep hardening characteristics and fine grain structure. Temperature of the quenching oil should be 120°-140°F for best results. Do ... morenot quench in water because this is an oil hardening steel.
Buy It Now
$26.97 Shipping Condition: New Location: Tolland, United States Typical Analysis; Carbon. 38% -.43%, Manganese 0.75-1.00%, Chromium. 80%-1.10%, Molybdenum. 15%-.25% Typical applications include; Spindles, Rods, Shafts, ... moreStuds, Axles, Arbors, Gears, Machine Parts, Inexpensive Tooling, Short Run Stamping Dies.
Buy It Now
$20.81 Shipping Condition: New Location: Tolland, United States 420 Stainless Steel Decarb Free Annealed Plate; 1 Piece; 1" Thick X 3" Wide X 12" Length. All available as standard or oversize. In house Blanchard Grinding ... moreto 60" and Surface grinding to 120". Width and Length are Saw Cut Nominally Oversize Approx +1/16" / +1/8".
Buy It Now
$16.32 Shipping Condition: New Location: Tolland, United States In house Blanchard Grinding to 60" and Surface grinding to 120". All available as standard or oversize. All sizes of 1018 Cold Finished Bar. Also available ... morein a full range of other sizes and lengths.
Buy It Now
$9.99 Shipping Condition: New Location: Tolland, United States 4140 Decarb Free Heat Treated / Pre-Hard Plate; 1 Piece; 1/4" Thick X 1" Wide X 12" Length. 4140 Round Bar also available in a full range of other Sizes, ... moreLengths & Surface Conditions Including HR Annealed, HR Heat Treated and TGP Heat Treated.
Buy It Now
$30.59 Shipping Condition: New Location: Tolland, United States 12L14 gives a smooth, machined surface and because of its low friction component allows for increased tool life. As material has a Lead additive [.15/.35] ... moreit cannot be welded. O-1, A-2, D-2, S-7, 4142PH, A-6, M-2, Low Carbon and other grades.
Buy It Now
$20.00 Shipping Condition: New Location: Tolland, United States 1018 Bar --1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high ... morestrength. Used for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$57.93 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$32.78 Shipping Condition: New Location: Tolland, United States 12L14 gives a smooth, machined surface and because of its low friction component allows for increased tool life. As material has a Lead additive [.15/.35] ... moreit cannot be welded. O-1, A-2, D-2, S-7, 4142PH, A-6, M-2, Low Carbon and other grades.
Buy It Now
$16.32 Shipping Condition: New Location: Tolland, United States 4140 Decarb Free Heat Treated / Pre-Hard Plate; 1 Piece; 3/4" Thick X 3" Wide X 12" Length. 4140 Round Bar also available in a full range of other Sizes, ... moreLengths & Surface Conditions Including HR Annealed, HR Heat Treated and TGP Heat Treated.
Buy It Now
Free Shipping Condition: New Location: Ferndale, United States Deep hardening characteristics and fine grain structure. Material Type: O-1 Standard. FREE Standard. Weight (lbs): 3.82.
Buy It Now
Free Shipping Condition: New Location: Ferndale, United States Deep hardening characteristics and fine grain structure. Material Type: O-1 Standard. FREE Standard. Weight (lbs): 2.23.
Buy It Now
$80.11 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$25.75 Shipping Condition: New Location: Tolland, United States 303 stainless steel turned, ground and polished to fit in standard bearings. Austenitic, non-magnetic stainless steel has good corrosion resistance, heat ... moreresistance and machinability. Conforms to ASTM A484 and A582.
Buy It Now
$82.56 Shipping Condition: New Location: Tolland, United States All available as standard or oversize. Length is Saw Cut +1/8"-.000. The Picture does not necessarily represent the item that you will get but they are ... moresimilar. In house Blanchard Grinding to 60" and Surface grinding to 120".
Buy It Now
$10.96 Shipping Condition: New Location: Tolland, United States Width and Length are Saw Cut Nominally Oversize Approx +1/16" / +1/8". Typical analysis; Carbon 1.50%, Silicon 0.3%, Manganese 0.50%, Chromium 12.00%, ... moreMolybdenum 0.80%, Vanadium 0.90%. D-2 Is used in applications requiring sharp cutting edges, wear and pressure resistance.
Buy It Now
$14.60 Shipping Condition: New Location: Tolland, United States S-7 Tool Steel is an air-or oil-hardening tool steel with a nice combination of exceptional toughness and wear resistance properties. S-7 is an excellent ... morechoice for blanking and die forming applications, as well as applications needing shock and impact resistance tools.
Buy It Now
$14.60 Shipping Condition: New Location: Tolland, United States Carbon Steel Grade S235 / 1018 Square Bar, Cold Finish Steel, 1 Piece 20MM Square (.7874") X 36" long. All sizes of 1018 Cold Finished Bar. Length is ... moreSaw Cut +1/8"-.00. S235/1018 Square Bar is a commonly used steel.
Buy It Now
$14.60 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is one of the most commonly used Low Carbon Content Steels. The steel has good hardening properties, fair machinability and is easy to ... moreweld. Good for applications that do not require high strength.
Buy It Now
$9.99 Shipping Condition: New Location: Tolland, United States Carbon Steel Grade 12L14 Cold Finished Leaded, 1 Piece; 5/8" Hexagon X 12" Length. 12L14 gives a smooth, machined surface and because of its low friction ... morecomponent allows for increased tool life. As material has a Lead additive [.15/.35] it cannot be welded.
Buy It Now
$15.48 Shipping Condition: New Location: Tolland, United States Approx weight is 8 lbs.Alloy Steel Grade 8620 is a widely used case hardening Alloy Steel. It's Nickel content imparts good toughness and ductility and ... morethe Chromium and Molybdenum content increases hardness penetration and wearability.Typical Chemistry; Carbon. 18/.23, Manganese 0.70/0.90, Phosphorus 0.035 Max, Sulfur 0.04 Max, Silicon 0.15/0.35, Nickel 0.40/0.70, Chromium 0.40/0.60, Molybdenum 0.15/0.25.
Buy It Now
$41.68 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$27.52 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$40.05 Shipping Condition: New Location: Tolland, United States Typical Analysis; Carbon. 38% -.43%, Manganese 0.75-1.00%, Chromium. 80%-1.10%, Molybdenum. 15%-.25% Typical applications include; Spindles, Rods, Shafts, ... moreStuds, Axles, Arbors, Gears, Machine Parts, Inexpensive Tooling, Short Run Stamping Dies.
Buy It Now
$23.67 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$27.52 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
Buy It Now
$20.81 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel alloy, this low carbon steels contains manganese. The steel has good hardening properties, fair machinability ... moreand is easy to weld. Good for applications that do not require high strength.
Buy It Now
$9.99 Shipping Condition: New Location: Tolland, United States Width and Length are Saw Cut Nominally Oversize Approx +1/16" / +1/8". Typical analysis; Carbon 1.50%, Silicon 0.3%, Manganese 0.50%, Chromium 12.00%, ... moreMolybdenum 0.80%, Vanadium 0.90%. D-2 Is used in applications requiring sharp cutting edges, wear and pressure resistance.
Buy It Now
$10.96 Shipping Condition: New Location: Tolland, United States 4140 Decarb Free Heat Treated / Pre-Hard Plate; 1 Piece; 3/8" Thick X 1" Wide X 12" Length. 4140 Round Bar also available in a full range of other Sizes, ... moreLengths & Surface Conditions Including HR Annealed, HR Heat Treated and TGP Heat Treated.
Buy It Now
$33.59 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.The picture does not necessarily represent the item you will get they they are similar.
Buy It Now
$33.59 Shipping Condition: New Location: Tolland, United States 1018 Bar--1018 is the most commonly used steel. The steel has fair machinability and is easy to weld. Good for applications that do not require high strength. ... moreUsed for bolts, machine parts, structural parts, gears, cams, worms and pinions.
|