|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China 1 5 Axis Standard Breakout Board + 4 EMA2-070D56 Microstep Motor Drivers. • Compatible with all the 2 phase, 3 phase and 4 phase microstep drivers in ... morethe market. •Automatic circuit protections function when the wirings between the breakout board and microstep drivers are incorrect.
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: China Support all versions of Mach3. Under Mach3 working state, USB cable unplugs and then plugs in, but also the normal connection. The indicator light indicates ... morevarious working status, such as USB connection, Mach3 connection and so on.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. The breakout board using high-performance three-state bus driver 74HC244 and Schmitt inverter 74HC14. The input ... moresignal is amplified, rectified, filtered to make the drive capability of the output signal more stable and stronger.
Buy It Now
$3.69 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
$2.39 Shipping Condition: New Location: China The output is P17. The output is P1. 9, can be connected to the common negative or common driver, the input level is 5V driver. Genuine For Dell Inspiron ... more15 3501 3505 3595 3585 3593 CPU Cooling Fan 7MCD0.
Buy It Now
$2.99 Shipping Condition: New Location: China Support connection with electronic handwheel. The maximum step pulse frequency is 100KHz, suitable for servo or stepper motors;. Unplug the USB cable! ... moreAs long as you unplug the USB cable, the machine will automatically stop.
Buy It Now
Free Shipping Condition: New Location: United States DIY CNC Kit 3 Axis With CNC Breakout Board + Cables + TB6600HG Stepper Drivers + 3 Pieces TB6600HG Stepper Driver Board Controller The latest upgraded ... moresalable 5 axis breakout board is specially designed for the CNC single axis stepper driver controller. Such as TB6600HG, M542, M542H, MA560, MA860H, 2M542, 2M982 etc single axis stepper driver controller. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover. The brand new design with BiCD0.13(45V) process technology on the chipset also ensures maximum 5.0A output current and 45V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps. All the 2 Phase or 4 Phase of Nema17. Nema23, Nema24 and Small-sized Nema34 stepper motors will work perfectly with this new-type TB6600HG Stepper Driver. Click here for In short. With this CNC Kit, you will get more benefits from the Kit on CNC work. Please purchase this kit with confidence. High performance. Cost-effective. Maximum support 5-axis stepper motor driver controller. Two types of ways to get power. 5V DC power supply or USB port to directly get power from PC. Two-stage signal processing. Smooth signal transmission, powerful anti-jamming. 5-input interface to define the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc. Relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. 5-axis work LED display. Visually display the working condition of the stepper driver controller. High performance. Cost-effective. Automatic idle-current reduction. Supply voltage up to 45V DC. Output current up to 5.0A. Suitable for 2-phase and 4-phase motors. High speed optoelectronic iso
Buy It Now
Free Shipping Condition: New Location: United States TB6600HG Stepper Motor Driver For Nema17/ 23/ 34+ 5 Axis Breakout Board Kit + 3 Pieces TB6600HG Stepper Driver Board Controller The latest 3rd generation ... morebreakout board has been upgraded to the intelligent. Professional and industrial-level interface board set by re-designing the PCB board, embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) The re-designing the PCB board will make the breakout board control the microstep drivers more smoothly with lower noise. Actually, the 3rd generation breakout board set has two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the" computer G-code recording function" And another is the" manual programing function" Except these two functions. These two types of versions have no other differences. With the embedded intelligent memory chip. The professional version of this 3rd generation 5 Axis breakout board can easily record MAXIMUM 4 Axis' X, Y, Z, A Axis) G-code running on the CNC software( e.g. Mach3. EMC2, KCAM4, etc. of the computer. And then rerun the recorded G-code to make the stepper motor work without the computer any more. The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover. The brand new design with BiCD0.13(45V) process technology on the chipset also ensures maximum 5.0A output current and 45V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps. All the 2 Phase or 4 Phase of Nema17. Nema23, Nema24 and Small-sized Nema34 stepper motors will work perfectly with this new-type TB6600HG Stepper Driver. Click here for In short. The qualities and functions of the ne
Buy It Now
Free Shipping Condition: New Location: China High Step-Pulse Frequency: Supports a maximum step-pulse frequency of 100KHz, suitable for both servo and stepper motors. Connection Status Indicator: ... moreA status LED on the board indicates the connection status for user convenience.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States Hording torque when DM542A run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is ... morealso higher. Stepper motor driver DM542A 3 pcs Nema 23 stepper motor 425 oz.in bipolar with single shaft, 3.0A.
Buy It Now
$3.99 Shipping Condition: New Location: China 1 x Adapter Breakout Board. The output port is P17 port. The output port is P1 port. Connectors: USB(Female)+25PIN(Male). 1 x USB Cable.
Buy It Now
$4.00 Shipping Condition: New Location: China Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. It is suitable for driving 2-phase and 4-phase hybrid stepping motors, the Nema 23, Nema 34 stepper motor with ... morea 2.4A-7.2A current will be suitable. ™ digital hybrid stepper driver is a high performance Microstep Motor Driver adopting32-bit DSP, pure sine wave subdivision technology.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Supports connection of electronic handwheel. The maximum step pulse frequency is 100KHz, suitable or stepper motors;. Supports 4 -axis linkage and can ... moreconnect 4 stepper motor drivers or drivers;. 1 status LED, indicating the connection status on the board.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip ... morePWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
Buy It Now
Free Shipping Condition: New Location: United States 5Axis CNC Router Mill Breakout Interface Board. LCD Display, KeyPad,Gcode Record Descriptions I. About the 3rd Generation Breakout Board Set This breakout ... moreboard has been upgraded to an intelligent and industrial-level interface board set. The redesigned PCB board enables smoother control of microstep drivers and stepper motors with lower noise. It has high compatibility with all the 2-phase. 3-phase and 4-phase microstep drivers and stepper motors. The equipped manual control tools bring more user friendly experience. It has standard version and professional version to meet different user needs. II. Standard Version VS Professional Version. Functions, Standard Version, Professional Version, Intelligent motor control via PC, Manual motor control via control panel, Intelligent switch between PC and control panel, Synchronous coordinates display on PC and display panel, Real-time tracking of motor moving path, Automatic G-code recording, Manual G-code programming, III. Two Unique Functions of Professional Version. Automatic G-code recording function With the embedded intelligent memory chip. This breakout board can easily record MAXIMUM 4 axis' X.Y,Z,A axis) G-code running on the CNC software(e.g. Mach3. EMC2, KCAM4. Etc. of the computer, after which you can control the microstep drivers and stepper motors via using the recorded G-code without computer. Manual G-code programing function. The upgraded built-in manual control tools(display panel and control panel) not only can be used for manual motor control. But also for manual G-code programming. Manually programmed G-code will be recorded onto the embedded intelligent memory chip. After which you also can easily control the microstep drivers and stepper motors with recorded G-code. This function is widely applied in RBI machine, Conveyor etc. This package is 5 Axis Professional Version(BCD-P) If you need the standard version. Please refer to our related item or simply contact us. PCB Instructions Features High performance. Cost-effective; Manual motor c
Buy It Now
$3.69 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
$3.99 Shipping Condition: New Location: China 1 x Handwheel. - 1 x USB CNC 9 Axis. - Model Number: usb cnc 9 axis. - Slave axes. - 7 digital outputs on board. - SD card support for running g-code ... morewithout computer. Basic connection diagram - Motor type: Stepper Motor.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip ... morePWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
Buy It Now
$2.09 Shipping Condition: New Location: China 1PCS MACH3 Engraving Machine 5 Axis CNC Breakout Board With Optical Coupler. 1x USB Cable. Dual Channel DC Motor Driver Module 160W 7A 12V 24V H-bridge ... moreL298. Due to the light and screen difference, the item's color may be slightly different from the pictures.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The breakout board using high-performance three-state bus driver 74HC244 and Schmitt inverter 74HC14. The input signal is amplified, rectified, filtered ... moreto make the drive capability of the output signal more stable and stronger.
Buy It Now
$3.00 Shipping Condition: New Location: China Handwheel interface: support. - Applicable software: Mach3. - Pulse rate: 200K max (per axis). - Number of axes: 5 axes (XYZ axes and two rotation axes). ... more- Data interface: Ethernet. - Its transmission distance is farther than that of USB motion card.
Buy It Now
$3.89 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
Free Shipping Condition: New Location: 金东区, China Supports connection of electronic handwheel. The maximum step pulse frequency is 100KHz, suitable or stepper motors;. Supports 4 -axis linkage and can ... moreconnect 4 stepper motor drivers or drivers;. 1 status LED, indicating the connection status on the board.
Buy It Now
$3.00 Shipping Condition: New Location: China When the Mach4 is working, unplug a USB cable and then plug it back in, the Mach4 can still be connected normally. - Its status indicators can indicate ... morevarious statuses, including USB connection status, Mach4 connection status and running.
Buy It Now
$5.00 Shipping Condition: New Location: China Model Number: USB CNC 4 Axis MDK2. - Motor type: Stepper Motor. - 1 x 4-Axis USB CNC Breakout Board. - Slave axes. - SD card support for running g-code ... morewithout computer. - 1 x USB cable. - USB connection.
Buy It Now
$1.99 Shipping Condition: New Location: China The output is P17. 9, can be connected to the common negative or common driver, the input level is 5V driver. The output is P1.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA232-7630S4 Nema23 Stepper Motor. Stepper motors and drivers from ENGMATE. ™ 5 Axis Kit for CNC DIY. 5 Axis Standard Breakout Board. • Suitable for ... more2-phase and 4-phase Hybrid stepper motors. • Compatible with all the 2 phase, 3 phase and 4 phase microstep drivers in the market.
Buy It Now
Free Shipping Condition: New Location: Rowland Heights, United States 1 pcs Nema 34 stepper motor 1700 oz.in 6A with single Shaft. Nema 34 stepper motor Hording torque when DM860A run under high speed is also significantly ... morehigher than the other two-phase driver, what’s more, the positioning accuracy is also higher.
Buy It Now
$3.00 Shipping Condition: New Location: China Output frequency:2000 KHZ (2MHz). Applications: MK4-V:4 axis motion card works with Mach3 CNC system under all windows platform. Mach3 Port Position: ... moreP1 Port. - Fully support all Mach3 version. - 16 general-purpose input,8 output has speed function,the spindle actural speed Mach3.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA232-5615S4 Nema23 Stepper Motor. Stepper motors and drivers from ENGMATE. • Suitable for 2-phase and 4-phase Hybrid stepper motors. ™ 4 Axis Kit for ... moreCNC DIY. Hybrid Stepper Motor(EMA232-5615S4). 5 Axis Breakout Board.
Buy It Now
$2.40 Shipping Condition: Brand New Location: China 5 Axis Breakout Board Item Description Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power ... moresupply and peripherals powered phase separation to protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 1X 5 Axis Breakout Board 1X USB cable Payment Description* We do only accept PayPal. We only ship to PayPal confirmed address. For international buyers. We only ship to PayPal verified users. So before bidding, please kindly verify your PayPal account. Shipping Description Note: We will repackage this item to reduce shipping weight and also paper. Bag waste. We guarantee the item will be treated well, and also protected well. Please help US reduce waste, Let us protect the environment together! Thanks. Some units may have minor scuffs/ scratches from being bulk shipped to warehouse. We guarantee the product is new. We ship this item from US We offer Best Price and Fast Shipping Domestic Shipping: We ship to United States including APO/FPO addresses. Puerto Rico, Hawaii, Virgin Islands, etc. with delivery confirmation numbers. We use USPS service or UPS Mail Innovation(USPS Services) Shipping time is estimated in 5- 9 Days. We are not responsible for service transit time. This information is provided b
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China QUALITY-GADGETS eBay Item! Upgraded 5 Axis Cnc Breakout Board For Microstep Controller + Cables + Software 5 Axis USB Breakout Board For CNC Single Stepper ... moreMotor Driver Controller Descriptions: The latest upgraded salable 5 axis breakout board is speacilly designed for the CNC single axis stepper driver controller. Such as M542, M542H, MA560, MA860H, 2M542, 2M982, DM542(A) DM860(A) etc single axis stepper driver controller series. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. Key Features: Upgraded circuit. Work more peacefully and steady than the previous version Maximum support 5-axis stepper motor driver controllers Two ways to get power. 5V DC power supply or USB port to get power from PC directly Two-stage signal processing. Smooth signal transmission, powerful anti-jamming 5-input interface to define the Limit. Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc. Relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. 5-axis work LED display. Visually display the working condition of the stepper driver controller Wiring Diagram: Electrical properties(ambient temperature Tj = 25 ℃ pm) Input Power 5V DC power supply or USB port to directly get power from PC Compatible Stepper Motor Driver Max 5 single axis stepper motor driver controller Drive type Pulse + Direction + Enable Signal Control Net/Total Weight Approx 80g/300g Dimensions 90* 82* 15mm(L*W*H) 1 x 5 Axis Breakout Board 1 x DB25 Parallel Cable 1 x USB Power Cable 1 x CD Click here for the Mach3 software USD 193.69(Free P&P* USD 185.84(Free P&P* USD 276.69(Free P&P* USD 58.05(Free P&P* USD 60.99(Free P&P* USD 83.80(Free P&P* USD 86.99(Free P&P* USD 72.19(Free P&P* GBP 83.49(Free P&P* GBP 205.99(Free P&P* USD 64.40(Free P&P* USD 77.69(Free P&P* GBP 89.29(Free P&P* USD 63.79(Free P&P* USD 36.66(Free P&P* USD 31.59(Free P&P* USD 66.49(Free P&
Buy It Now
$4.00 Shipping Condition: New Location: China Can be connected to electronic handwheel. - 1 x Mach3 Board. - Maximum step-pulse frequency is 100KHz, which is suitable for servo and stepping motor. ... more- 1 status LED to indicate connection status on the board.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China 5 Axis Stepper Motor Driver Interface Breakout Board, Features: For stepper motor driver-Can most connection 5pcs driver and control 5pcs motor in the ... moresame time-With 4-wire limit switch to insure our safty movement-With relay port to contro the cnc spindle-Working voltage is 5VDC and support with MACH3.EMC2,KCAM4 software Db25 pin( pc pin) The pin of the interface board Comment(signal) 1 Step 5 Fifth axis pulse 2 Step x X pulse 3 Dir x X axis direction 4 Stepy Y pulse 5 Dir y Y axis direction 6 Step z Z axis pulse 7 Dir z Z axis direction 8 Step 4 Fourth axis pulse 9 Dir 4 Fourth axis direction 10 Limit-1 Limit input interface 1 11 Limit-2 Limit input interface 2 12 Limit-3 Limit input interface 3 13 Limit-4 Limit input interface 4 14 Dir 5 Fifth axis direction 15 Vacant 16 Rly Relay control 17 En All axis enable 18-25 Gnd Gnd Package 100% Brand New 1 x 5 Axis Stepper Motor Driver Interface Breakout Board Shipping 1. Items will be sent out within 48 hours(except weekend and holidays) after we receive the payment. All items are shipped by Singapore or HongKong Post air mail without tracking number.Unless buyers pay extra money. 2. It is estimated that package will arrive in 10-30working days. holidays and weekends are not included) to most countries! If you donot get the items after 30 working days please email us we will Refoud or Reship. 3. Since air mail will takes long time for delivery. If you want items urgently, you could contact us to ask shipping cost of Express mail.such as DHL or EMS or TNT or UPS) 4. We are not responsible for any custom duty or import thanks 5. We only ship the item to the address listed in your paypal payment. Please make sure your shipping address is correct. 6. If you have any request(e.g. change address) Please put a note on paypal. Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-30 30 Working Days + Saturday + Sunday 5-9 10-14 15-20 21-25 26-30 35 United States Rate(item arrived) 9% 50% 21% 13% 7% Refund or Resend United Kingdo
Buy It Now
Free Shipping Condition: New Location: 金东区, China New CNC MACH3 USB 6 Axis Interface Breakout Board Adapter For Stepper Motor Driver#A145A. Click To Enlarge MACH3. CNC software for mainframe computers ... moreand peripheral power control signal transfer and processing. Feature 1, all output and input models by Philips dedicated high-speed chip processing. The signal is an integer, amplification, eliminating unnecessary interference signal. The operation of the machine more stable. 2. USB and external power supply. The power supply isolation. Computer and data processing machines more secure 3, all of the input signal by the optical coupling isolation all of which P11. P12 port for high-speed optical coupling can be used to connect the spindle encoder, or hand- wheel A. B equal to demanding signal. 4, there is a special off the total electric power supply of the relay, the computer shuts down automatically when carving machine with other equipment, turn off all power. 5, there is a special relay switch coolant supply, support MACH3. G code programming( parallel port P3. G code to open M8. M9 off) the relay switch on the lights. Easy to determine the power off. 6, there is a spindle-powered ad hoc relay support MACH3. G code programming( parallel port P2 I. G to open the code M3. M2 off) the relay switch on the lights. Easy to determine the power-off 7. On the spindle speed control: special high-speed optical coupling isolation, can output PWM signal output for the parallel port P1. 8, the interface board have a PWM to 0-10V digital-analog conversion circuit. Can output 0-10V level to control the market and control the speed of only analog converter. To control the spindle speed. Output for the parallel port P1. 9. The interface board can be connected common cathode or common anode output to the stepper drive or servo drive. Output for the 5V level. 10. Wide voltage power supply, 12V or 16-35V can choose a set of two power supply. Reversed with anti- power input design. 5 input port： Port description P10 X limit P11 on the knife P
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States 1-LPH 26-Pin to DB-25 Ribbon Cable With DB25 EMI Filter To Attach To Your Breakout Board, G540, Or LeadShine Drive. G540 Digital 4 Axis Driver Specs The ... moreWarp9 Ethernet Smooth Stepper (Turnkey System) - YouTube.
Buy It Now
Free Shipping Condition: New Location: China We promise try our best to help solve any problem. Part of second-hand products will have obvious scratches on the surface.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. This function is widely applied in RBI machine, Conveyor etc. This kit is suitable for driving 2-phase and 4-phase ... moreNema 17, Nema 23 hybrid stepping motors with a 1.0A-4.2A current.
Buy It Now
$8.00 Shipping Condition: New Location: China When the Mach4 is working, unplug a USB cable and then plug it back in, the Mach4 can still be connected normally. - Its status indicators can indicate ... morevarious statuses, including USB connection status, Mach4 connection status and running.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China DIY TB6600HG Stepper Driver CNC Kit 3 Axis Nema24 Stepper Motor Display& Handle +3x Nema24 4Nm/567 Oz-in GB24H2100-42-4A Stepper Motors +2x 360W 36V10A ... moreSwitching Power Supply +3x TB6600HG Microstep Drivers The latest 3rd generation breakout board has been upgraded to the intelligent. Professional and industrial-level interface board set by re-designing the PCB board, embedding intelligent memory chip(professional version) and upgrading the external manual control tools(control pad and display panel) The re-designing the PCB board will make the breakout board control the microstep drivers more smoothly with lower noise. Actually, the 3rd generation breakout board set has two types of versions, one is the standard version. And another is the professional version. Compare to the standard version. The professional version mainly has two more functions than the standard version, one is the" computer G-code recording function" And another is the" manual programing function" Except these two functions. These two types of versions have no other differences. With the embedded intelligent memory chip. The professional version of this 3rd generation 5 Axis breakout board can easily record MAXIMUM 4 Axis' X, Y, Z, A Axis) G-code running on the CNC software( e.g. Mach3. EMC2, KCAM4, etc. of the computer. And then rerun the recorded G-code to make the stepper motor work without the computer any more. The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover. The brand new design with BiCD0.13(45V) process technology on the chipset also ensures maximum 5.0A output current and 45V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps. All the 2 Phase or 4 Phase of Nema17. Nema23, Nema24 and Small-sized Nema34 stepper motors will work perfectly with this new-type TB660
Buy It Now
Free Shipping Condition: New Location: China ● Y-axis dual drive, stronger drive capability;. ● XY limit switch interface each. ● One-piece integrated drive.
Buy It Now
$89.00 Shipping Condition: New Location: Denmark • Built in DB25 male connector. • DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17. • DB25 Input Pin: P10,P11,P12,P13,P15. • DB25 GND Pin: P18-P25. ... more1PCS Breakout Board. Breakout Board. P4 P5 is set to Y-axis, Y axis pulse.
Buy It Now
$2.99 Shipping Condition: New Location: China 1PC MACH3 Interface Board. The output interface. The output interface is P1. Cable length:Approx.130 cm. 1PC USB Cable. Equiped with anti-reverse connection ... morefunction.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA342-10050S4 Nema34 Stepper Motor. Stepper motors and drivers from ENGMATE. • Suitable for 2-phase and 4-phase Hybrid stepper motors. Hybrid Stepper ... moreMotor(EMA342-10050S4). ™ 5 Axis Kit for CNC DIY.
Buy It Now
Free Shipping Condition: New Location: China MK6-V: 6 axis motion card works with Mach3 CNC system for all Windows platform. Output frequency: 2000 KHZ (2MHz). Mach3 Port Position: P1 Port. - Fully ... moresupport all Mach3 version. - 16 general-purpose input,8 output has speed function, the spindle actual speed Mach3.
Buy It Now
$9.95 Shipping Condition: New Location: Hoffman Estates, United States Project Artois Crejz Project Artois Crejz 3 Axis CNC USB Card Mach3 200KHz Breakout Board Interface Windows2000/XP/Vista The Features of the card: Support ... moreall the Mach3 version.Including the latest edition:Mach3 R3.042.040*Support all the Windows version.Including the latest edition:Windows7. No Driver needed for USB.All the Windows version can be used as soon you insert in it. Fully support USB hot swapping.To monitor USB attachment state any time. While Mach3 are working,if you uproot USB cable, then plug it also can make it work at once. Support four shaft linkage.Including inching. As well as four shaft linkage. To support the following functions: Automatic tool-setting.Electronic hand wheel, software limit, software backlash* Speed: 48M, so you don’t need to use PC. The Signal is independently processed by the Movement Control Cards. Ensuring that you get really real-time information and reliability. Get 200KHz output. Link to Stepping/Service. Have status indicator. Can indicate Mach3 attachment. And USB connectivity, when it is on, all kinds of state are clear for you at a glance. Have 16 input indicators.It Clearly indicates the status of signal-input. Have Speed-measurement function.The Spindle actual speed is displayed on the Mach3 interface in real time. And innovatively provide real-time speed graph, Making the speed variations clear and lively. Have on-board isolation power supply. NO external power supply Simplify the requirements of electric power supply. It’s convenient to connect external power supply can also be used, so you can have any choice you like. There are 10 super-speed 10 MHz light-couplers. 24General light-couplers, so the total amounts of light-couplers are up to 34. Isolate all the input/output. The High costs design provides a complete anti-jamming function and perfect security protection. The Product Information: 200KHz.4 axis output, frequency 200KHz. Use 10MHz high-speed optical coupling to isolate electric power. Support 16 input points. 16 input-isolation l
Buy It Now
$8.00 Shipping Condition: New Location: China Support all versions of Mach3, including the latest version. - The dual core ultra high speed CPU (single core maximum frequency 204MHz) has great redundancy ... morein computing power. And ensure the realization of the pulse output frequency of 1000KHz under the 3 axis linkage, the pulse output frequency of 750KHz under the 4 axis linkage, the output frequency of the 6 axis linkage pulse is up to 500KHz, and the servo / step can be connected.
Buy It Now
$2.99 Shipping Condition: New Location: China Applicable to all versions of mach3 software;. Current:＞500MA. 1x USB Cable. DC 5V-15V Frequency Square Wave Pulse Generator Oscillator Output Signal ... moreSource. 1hz-150Khz Signal Generator Module Square Wave PWM Pulse Frequency Duty Ratio.
Buy It Now
$3.89 Shipping Condition: New Location: China 5 Axis Breakout Board Item Description Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power ... moresupply and peripherals powered phase separation to protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 1X 5 Axis Breakout Board 1X USB cable Payment Description* We do only accept PayPal. We only ship to PayPal confirmed address. For international buyers. We only ship to PayPal verified users. So before bidding, please kindly verify your PayPal account. Shipping Description Note: We will repackage this item to reduce shipping weight and also paper. Bag waste. We guarantee the item will be treated well, and also protected well. Please help US reduce waste, Let us protect the environment together! Thanks. Some units may have minor scuffs/ scratches from being bulk shipped to warehouse. We guarantee the product is new. We ship this item from US We offer Best Price and Fast Shipping Domestic Shipping: We ship to United States including APO/FPO addresses. Puerto Rico, Hawaii, Virgin Islands, etc. with delivery confirmation numbers. We use USPS service or UPS Mail Innovation(USPS Services) Shipping time is estimated in 5- 9 Days. We are not responsible for service transit time. This information is provided b
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China 1. Included: 1PC Mach3 Interface Board 1PC USB Cable 2. Specifications& Feature 1, fully support MACH3 and other computer software that supports parallel ... moreport control. 2, USB power supply and peripheral power supply are separated to ensure computer security. 3, the peripheral wide voltage input, 12-24V, and anti-reverse function. As shown in Figure 4, all input signals are isolated by optical diaphragm, which can be connected to emergency stop, tool setting, limit, etc. to ensure computer security. 5, one way relay output port, can control the spindle switch. The output port is P17 port. 6, one channel through the optocoupler isolation 0-10V analog voltage output, can control the inverter with the corresponding analog interface, control Spindle speed. The output port is the P1.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Upgrade 5 Axis Cnc Breakout Board For Microstepper Driver Controller + USB Cable The latest upgraded 5 axis breakout board is specially designed for the ... moreCNC single axis 2-phase stepper driver controller. The breakout board using high-performance three-state bus driver 74HC244 and Schmitt inverter 74HC14. amplified. The input signal is amplified, rectified, filtered to make the drive capability of the output signal more stable and stronger. With this 5 axis breakout board, any 1-5 Microstepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. parallel-control CNC software High performance. Cost-effective. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3. Linux CNC(EMC2) etc. parallel-control CNC software. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security. 5-input interface to define the Limit. Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V. And with anti-reverse function. One relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. Compatible with all the 2 phase microstep drivers in the market. Output 0-10V analog voltage for inverter to control the spindle speed. Shape Pulse and direction signals. Data transfer speeds of up to 10MBit/S. Amplification. Filtering, enhancement processing drivers enable signal. Suitable for a wide range of 2-phase microstep drivers in the market. Such as M542. M542H, MA860H, 2MA2278, 2M542, 2M860 etc. For advising. Such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc.It can be used in various kinds of machines, such as X-Y tables, labeling machines, laser cutters, engraving machines, pick-place devices, and so on. This breakout board is just a interface board. NOT a stepper driver board, it must work together with the microstep drivers(eg. MA860H etc. to control the st
Buy It Now
$2.00 Shipping Condition: New Location: China CNC turntable support. Single-step mode, the user can set the processing task to be executed to single-step mode, which provides good support for error ... morediagnosis and fault recovery. 1x Parallel Cable.
Buy It Now
$3.99 Shipping Condition: New Location: China Features: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation ... moreto protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Package included: 100% Brand New 1X 5 Axis Breakout Board 1X USB cable PayPal only. Only ship to PayPal confirmed address. All items are shipped via HK Air Mail Service within 48 Hours once payment's fulfilled. Buyers are responsible for any customs duties if applicable. Normally item will arrive in 10-20 days. Sometime a bit delayed. If item is defective upon receipt. Customer has up to 14 days from date of receipt for an exchange or refund. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. If you need to return. Please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. If you’re in any way dissatisfied with your purchase. Let me know through" MY MESSAGES" or"AskSeller Q"or our mailbox. We will solve it for you. We are committed to ensuring that you are completely satisfied with every transaction.100% Satisfaction guaranteed! We will reply your mail within 24 hours normally. sometimes have a little delay due to the weekends or ho
Buy It Now
$1.94 Shipping Condition: Brand New Location: China New CNC MACH3 USB 6 Axis Interface Breakout Board Adapter For Stepper Motor Driver#A145A. Click To Enlarge MACH3. CNC software for mainframe computers ... moreand peripheral power control signal transfer and processing. Feature 1, all output and input models by Philips dedicated high-speed chip processing. The signal is an integer, amplification, eliminating unnecessary interference signal. The operation of the machine more stable. 2. USB and external power supply. The power supply isolation. Computer and data processing machines more secure 3, all of the input signal by the optical coupling isolation all of which P11. P12 port for high-speed optical coupling can be used to connect the spindle encoder, or hand- wheel A. B equal to demanding signal. 4, there is a special off the total electric power supply of the relay, the computer shuts down automatically when carving machine with other equipment, turn off all power. 5, there is a special relay switch coolant supply, support MACH3. G code programming( parallel port P3. G code to open M8. M9 off) the relay switch on the lights. Easy to determine the power off. 6, there is a spindle-powered ad hoc relay support MACH3. G code programming( parallel port P2 I. G to open the code M3. M2 off) the relay switch on the lights. Easy to determine the power-off 7. On the spindle speed control: special high-speed optical coupling isolation, can output PWM signal output for the parallel port P1. 8, the interface board have a PWM to 0-10V digital-analog conversion circuit. Can output 0-10V level to control the market and control the speed of only analog converter. To control the spindle speed. Output for the parallel port P1. 9. The interface board can be connected common cathode or common anode output to the stepper drive or servo drive. Output for the 5V level. 10. Wide voltage power supply, 12V or 16-35V can choose a set of two power supply. Reversed with anti- power input design. 5 input port： Port description P10 X limit P11 on the knife P
Buy It Now
Free Shipping Condition: New Location: 金东区, China Support connection of electronic handwheel. The maximum step pulse frequency is 100KHz, suitable for servo or stepper motors;. 1 status LED to indicate ... morethe connection status on the board. 1 x USB cable.
Buy It Now
Free Shipping Condition: New Location: 龙岗区, China Maybe you also interested it: CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board From Hong Kong. Stepper Motor Drive Controller ... moreBoard Module L298N Dual H Bridge DC For Arduino From Hong Kong. Stepper Motor Drive Module L298N Dual H Bridge DC +28BYJ-48 5V Stepper Motor DC From Hong Kong. Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino From Hong Kong. ULN2003AN ULN2003 Stepper Motor Driver Board Module for Arduino AVR ARM SMD L9110S H-bridge Stepper Motor Dual DC motor Driver Controller Board for Arduino From Hong Kong. 28BYJ-48 Valve Gear Stepper Motor DC 5V 4 Phase Step Motor Reduction For Arduino From Hong Kong. 5V Stepper Motor 28BYJ-48 With Drive Test Module Board ULN2003 5 Line 4 Phase From Hong Kong. Motor Drive Shield Expansion Board L293D For Arduino Duemilanove Mega2560 UNO From Hong Kong. StepStick Stepper motor driver A4988 A4983 3D Printer driver module Reprap Prus From Hong Kong. Item Description: 1. Fully support of MACH3 and other computer software support for parallel port control. 2. USB power supply and peripherals powered phase separation to protect computer security. 3. Peripheral wide voltage input,12-24V, and anti-reverse function. 4. All of the input signal, all the light lotus isolated, which can be accessed emergency stop on the knife, the limit to protect computer security. 5. All the way to the relay output port, control spindle switch. Output port P17 mouth. 6. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port. 7. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled. 8. P1 as PWM outputs can be controlled with optocoupler input spindle governor. 9. Can be accessed by a common cathode or common anode input level to 5V drive. Downlo ad We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is ve
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. EMA232-5615S4 Nema23 Stepper Motor. 5 Axis Standard Breakout Board. •Automatic circuit protections function when ... morethe wirings between the breakout board and microstep drivers are incorrect.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China Stepper motors and drivers from ENGMATE. EMA112-4506S4 Nema11 Stepper Motor. The breakout board using high-performance three-state bus driver 74HC244 ... moreand Schmitt inverter 74HC14. The input signal is amplified, rectified, filtered to make the drive capability of the output signal more stable and stronger.
|
|
|
 |