|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Free Shipping Condition: New Location: Bothell, United States To get started with FreeSoc2 see this link. 32-bit ARM Cortex-M3 CPU, 32 interrupt inputs. 24-bit 64-tap fixed-point digital filter processor (DFB). Up ... moreto 256 KB program flash, with cache and security features.
Buy It Now
Free Shipping Condition: New Location: Dawsonville, United States Everything included in this ad is shown in the pictures unless otherwise stated. We will help to resolve any issues quickly and fairly. Everything included ... morein the ad is shown in the pictures and listed in the accessories line unless otherwise stated.
Buy It Now
Free Shipping Condition: New Location: Clinton, United States Features: Compatible with the SparkFun Qwiic and STEMMA QT connect system which is an ecosystem of I2C sensors, actuators, shields and cables that make ... moreprototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin connector.
Buy It Now
$3.80 Shipping Condition: New Location: San Ramon, United States In particular, we think this sensor set is ideal for AHRS-based orien tation calculation s: the gyro stability.
Buy It Now
$6.05 Shipping Condition: Used Location: Seattle, United States This board allows you to interface with your car's OBD-II bus. It provides you a serial interface using the ELM327 command set and supports all major ... moreOBD-II standards such as CAN and JBUS
Buy It Now
Free Shipping Condition: New Location: Farmington, United States Type - Interface. Item(s) described above and exactly what's pictured.
Buy It Now
$5.35 Shipping Condition: Used Location: Cincinnati, United States Please see photos as they are of actual item you will receive. Hobbyist circuit board.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The NAU7802 is an ADC with built in gain and I2C output to amplify and convert the readings from a standard load cell. A load cell is basically a device ... morethat translates pressure or force into electrical signals.
Buy It Now
Free Shipping Condition: New Location: Harrison City, United States SparkFun mbed Starter Kit KIT-14458.
Buy It Now
Free Shipping Condition: New Location: Farmington, United States Edison to mount a microSD card as an internal drive. The microSD block allows the. Item(s) described above and exactly what's pictured.
Buy It Now
$5.00 Shipping Condition: New Location: Alameda, United States Sparkfun Electronics Kit To Use With The Sparkfun Inventor’s Kit (Not Included). Condition is New. Shipped with USPS Ground Advantage.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The main components of the Bus Pirate are the PIC24FJ64 processor and a FT232RL USB-to-Serial chip. A Mini-B USB connector that has also been populated ... moreon the board, provides the power to the Bus Pirate and allows you to interact with via your PC.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. The Serial Basic uses the CH340G IC to quickly ... moreand easily convert serial signals to USB. Based on the CH340G IC from WCH.
Buy It Now
$9.99 Shipping Condition: New Location: Phoenix, United States Do you see what we see?. This kit includes a breakout as well as the Lepton® 2.5 longwave infrared (LWIR) imager. Includes: 1x FLIR Lepton 2.5 - Thermal ... moreImaging Module. 1x FLIR Lepton - Breakout Board v2.0.
Buy It Now
$11.60 Shipping Condition: For parts or not working Location: Queen Creek, United States This is a lot of new and used parts for various Arduino projects.
Buy It Now
Free Shipping Condition: New – Open box Location: Harker Heights, United States Brand new
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The MCP4728 is the answer to your wishes! All over I2C! STEMMA QT - SparkFun Qwiic connector compatible. Size: 1.0" x 0.7" x 0.2". Item Specifics.
Buy It Now
$4.75 Shipping Condition: New Location: Fitzwilliam, United States So that we can resolve the isssue.
Buy It Now
$3.80 Shipping Condition: New Location: San Ramon, United States These two sens ors combine to make a nice 9- DoF kit, that c an be used fo r motion and orientation sensing. In particular, we think this sensor set is ... moreideal for AHRS-based orien tation calculation s: the gyro stability.
Buy It Now
$7.52 Shipping Condition: New Location: Germany The Wii controllers use a standard I2C interface and there is code available for both Arduino (https://github.com/madhephaestus/WiiChuck) and CircuitPython ... more/ Python (https://github.com/adafruit/Adafruit_CircuitPython_Nunchuk ) for quick integration with an Arduino UNO, Feather or even a Raspberry Pi. We like to use this with the Wii Nunchuck, because you can accommodate an XY joystick, two buttons and an acceleration sensor in a handy housing. All data are transmitted via the I2C address 0x52, the address cannot be changed. To make it as easy to use as possible, we created this breakout in the Stemma QT form factor. You can either use a breadboard or the qwiic-compatible STEMMA QT connectors from SparkFun and are compatible with 5V voltage levels, as is common with Arduinos, as well as wit.
Buy It Now
$7.10 Shipping Condition: New – Open box Location: Chesapeake, United States Functional Condition: Untested. The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory ... moreagencies. Condition: New.
Buy It Now
$3.80 Shipping Condition: New Location: San Ramon, United States In particular, we think this sensor set is ideal for AHRS-based orien tation calculation s: the gyro stability.
Buy It Now
$3.80 Shipping Condition: New Location: San Ramon, United States Performance i s superior to t he LSM9DS0, L SM9DS1, L3GD2 0H + LSM303, MP U-9250, and eve n the. In particular, we think this sensor set is ideal for ... moreAHRS-based orien tation calculation s: the gyro stability.
Buy It Now
$6.40 Shipping Condition: New Location: Columbiana, United States The Qwiic Switch simplifies all of those nasty worries away into an easy to use I2C device! With our Qwiic system using the switch is as simple as calling ... morebutton.isPressed(). If you need multiple switches for your project, fear not!
Buy It Now
$5.80 Shipping Condition: New Location: San Ramon, United States Performance i s superior to t he LSM9DS0, L SM9DS1, L3GD2 0H + LSM303, MP U-9250, and eve n the. In particular, we think this sensor set is ideal for ... moreAHRS-based orien tation calculation s: the gyro stability.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States With this small breakout board, that is not much bigger than your fingernail, adding mass storage to your project will never be easier. Breakout level ... moretranslates all of its outputs back to the level of the hardware it’s connected to.
Buy It Now
$7.00 Shipping Condition: New Location: Colorado Springs, United States 2012 Arduino Uno R3 | Atmega328p | Rev 3 | USB | UNO | 328 ~ International CATEGORIES. Sensors Motor Controllers Wireless Arm Platforms Android LCD Motors ... moreBatteries other RN-41- Bluetooth Module BOB- Roving Networks! Use with Arduino Pro Mini! Description: This is a breakout board for the RN-41 Bluetooth module from Roving Networks with built in regulator and level shifters! The module is directly compatible with the Arduino Pros. Arduino Pro Minis, and LilyPad Arduinos. The module from Roving Networks is powerful, small, and very easy to use. This Bluetooth module is designed to replace serial cables. The Bluetooth stack is completely encapsulated. The end user just sees serial characters being transmitted back and forth. Press the'A' character from a terminal program on your computer and an'A' will be pushed out the TX pin of the module. Payment Policy. PayPal is the only method of payment. PAYMENT MUST BE MADE WITHIN 24 HRS OF PURCHASING, Items ship within 72 hours upon receipt, Shipping& Return Policy. SHIPPING TERMS& CONDITIONS We appreciate your business and look forward to working with you on your projects. We'd like you to know that each order that we receive is treated like the only order we receive. We will do our best to respond to your inquiry immediately. Lead time: For orders before 2 PM we strive to ship packages same day. Customers can expect their orders to be shipped within one business day. What is the"status" or"location" of my order. Our answer is this.Please refer to your tracking number. IF it says this. The U.S. Postal Service was electronically notified by the shipper on[date] to expect your package for mailing. This does not indicate receipt by the USPS or the actual mailing date. Delivery status information will be provided if/ when available. Information. If available, is updated periodically throughout the day. Please check again later. It means we printed your label. But the package has not been picked up by USPS. IF it says this. Your
Buy It Now
$3.80 Shipping Condition: New Location: San Ramon, United States Performance i s superior to t he LSM9DS0, L SM9DS1, L3GD2 0H + LSM303, MP U-9250, and eve n the. In particular, we think this sensor set is ideal for ... moreAHRS-based orien tation calculation s: the gyro stability.
Buy It Now
$9.99 Shipping Condition: New Location: Phoenix, United States This makes it simple for developers to connect a diverse set of new sensors to enable a variety of AI applications. We at SparkFun see this as more than ... moreenough potential to be yelling "Stop this crazy thing" to your friends & family!
Buy It Now
$9.99 Shipping Condition: New Location: United States Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an electrical ... moreconnection. We like using these slip rings to specifically transfer power in our spinning projects because regardless of the wires position in its rotation the power remains consistent!
Buy It Now
$6.23 Shipping Condition: New – Open box Location: New Fairfield, United States This CanaKit SparkFun XBee Wireless Kit includes two XBee modules, one XBee Explorer, one XBee Shield, and a set of R3 headers. It is an ideal kit for ... moreanyone looking to explore wireless communication through the XBee platform.
Buy It Now
$3.99 Shipping Condition: New Location: Derry, United States The MicroView is the first chip-sized Arduino compatible that lets you see what your Arduino is thinking using a built-in OLED display. This is the MicroView ... morecontroller that I received from being a backer for the product on Kickstarter. This particular bundle went for $95 on Kickstarter. It has only been used once and everything is in very good condition. Includes all original accessories such as: MicroView, MicroView Programmer, Solderless Breadboaord, 74HC595 Shift Rergister, 2N2222 Transistors, 1N4148 Diodes, DC Motor with Gear, Small Servo, SPDT 5V Relay, TMO36 Temp Sensor, Softpot, USB Extension Cable, Jumper Wires, Photocell, Tri-color LED, Red and Yellow LEDs, 10K Trimpot, Piezo Buzzer, Big 12mm Buttons, 330 and 10K Resistors,
Buy It Now
$8.60 Shipping Condition: New Location: Athens, United States Unsold surplus from when I was a SparkFun distributor years ago.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The 'must have' IC for TTL/CMOS projects finally has its own breakout board! This is the RS232 converter IC that is capable of running at 3V and communicating ... morewith 5V logic. All the pins you need to setup your RS232 to TTL connection are broken out.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. Connects ... moreto Sparkfun MicroView OLED display. Use to interface with your computer, Raspberry Pi, or other USB device.
Buy It Now
Free Shipping Condition: New Location: Wichita, United States
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States Reset button. Item Specifics.
Buy It Now
Free Shipping Condition: Used Location: Atlanta, United States For Sale: Arduino Uno R3 custom kit supplied by Sparkfun. Condition is used but includes almost all of the components that were part of the kit, in working ... moreorder.
Buy It Now
$4.49 Shipping Condition: For parts or not working Location: Derry, United States
Buy It Now
Free Shipping Condition: Used Location: Orlando, United States
Buy It Now
$7.50 Shipping Condition: New Location: Berlin, Germany Make your own game or robot controller with this tiny gamepad breakout board. This design features a 2-axis thumb joystick and 6 buttons (4 large and ... more2 small). The board communicates with your host microcontroller via I2C, so it's easy to use and doesn't take up any of your valuable analog or digital pins. There is also an optional interrupt pin that can inform your board when a key has been pressed or released, freeing up processor time for other tasks. To give you a quick start, this board comes with a STEMMA QT connector. The STEMMA QT connector is compatible with the SparkFun Qwiic I2C connectors. This allows you to make solderless connections between your development board and the gamepad, or daisy-chain it to a variety of other sensors and accessories via a compatible cable and 'hub'.
Buy It Now
$4.99 Shipping Condition: New Location: New Braunfels, United States
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States RedBoard has all of the hardware peripherals you know and love: 14 Digital I/O pins with 6 PWM pins, 6 Analog Inputs, UART, SPI and external interrupts.The ... moreSDA, SCL and IOREF pins are broken out so the RedBoard will be compatible with future shields.
Buy It Now
$15.70 Shipping Condition: New Location: Gig Harbor, United States Brand new - several available.
Buy It Now
$7.13 Shipping Condition: Neu Location: Berlin, Germany Adafruit QT Py, SAMD21 Entwicklungsboard mit STEMMA QT. Das kleine Dev-Board kommt mit dem beliebten SAMD21. Natives USB, welches von jedem Betriebssystem ... more(OS) unterstützt wird - kann in Arduino oder CircuitPython als serielle USB-Konsole, MIDI, Keyboard / Mouse HID und sogar als kleines Festplattenlaufwerk zum Speichern von Python-Skripten genutzt werden.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States Is it power you seek?. Qwiic connector. USB interface for programming and power. UF2 bootloader. Up to 6 SERCOM interfaces. 256KB SRAM.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States It's blue! It's thin! It's the Arduino Pro Mini! SparkFun's minimal design approach to Arduino. This is a 3.3V Arduino running the 8MHz bootloader. It's ... morea great board that will get you up and running quickly.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States This compact sensor uses I2C to communicate, and it's very easy to use. If you'd like, you can also use SPI to receive data (we just happen to prefer ... moreI2C here). It's a great match for the LSM6DSOX from ST!
Buy It Now
$96.32 Shipping Condition: New: Never Used Location: Thornbury, Australia
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States To power the RedBoard Turbo, just plug it into a USB port on your computer via the micro-B port or directly into the wall with the 5V tolerant barrel ... morejack. Qwiic Connector. The RedBoard Turbo can even be flashed over the Mass Storage Class (MSC) just like a flash drive.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States What a cutie pie! Or is it. a QT Py?. Sensors a-plenty. Hardware I2C port with STEMMA QT plug-n-play connector. Use any SparkFun Qwiic boards! Seeed Grove ... moreI2C boards will also work with this adapter cable.
Buy It Now
Free Shipping Condition: New Location: Anoka, United States Brand new, genuine, sealed Arduino Uno R3Also comes with:Monoprice 6ft USB cable (Part Number: 5438)Sparkfun 10 Piece Alligator Clips (Part Number: PRT-12978)
Buy It Now
$7.13 Shipping Condition: Neu Location: Berlin, Germany Adafruit VCNL4040 Abstands-/Lichtsensor, STEMMA QT / Qwiic. Mit einem Spannungsregler ausgestattet, lässt sich das Board sowohl bei 3,3 V als auch bei ... more5,0 V betreiben und eignet sich daher für die Verwendung mit Arduino und Raspberry Pi.
$4.11 Shipping Condition: New Location: Metamora, United States The Cu truly exemplifies the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point ... moreinto the world of FPGAs and the heart of your next project.
Buy It Now
$7.52 Shipping Condition: New Location: Germany OLEDs, inertial measuring devices and sensors - all plug-and-play thanks to the innovative linkable design: SparkFun Qwicc-compatible STEMMA QT connectors ... morefor the I2C bus, so you don't even have to solder! Simply plug in a compatible cable, connect it to the MCU of your choice and you can load software and measure light, for example. Pin compatible with the Seeed Xiao. The honeycomb-shaped pads allow you to solder them flat on a circuit board. In addition, an RGB NeoPixel (with controllable power pin for ultra-low power use) and a reset button (ideal for restarting your program or entering the bootloader) have been added to the QT connection. Native USB, which is supported by every operating system (OS) - can be used in Arduino or CircuitPython as a serial USB console, MIDI, keyboard / mou.
Buy It Now
Free Shipping Condition: New Location: Lenexa, United States The SparkFun RFID Qwiic Reader is a simple I2C based RFID breakout board for the ID-3LA, ID-12LA, and ID-20LA readers. Utilizing our handy Qwiic system, ... moreno soldering is required to connect it to the rest of your system.
Buy It Now
$4.55 Shipping Condition: Seller refurbished Location: Red Bank, United States SparkFun Inverters Kit Arduino 4.0. Condition is Seller refurbished. Shipped with USPS Ground Advantage.
Buy It Now
$7.50 Shipping Condition: New Location: Germany Don't you smell that? No problem, you can build your own digital olfactory organ with the ENS160 Gas Sensor. The ENS160 is a fully integrated MOX gas ... moresensor from ScioSense that is controlled via I2C. It combines multiple metal oxide-based sensors and heating elements on one chip to provide more detailed air quality data. Another useful element of this sensor is the ability to set temperature and humidity compensation for better accuracy. This requires an external humidity sensor, the value of which is then written to the sensor over I2C so that it can better calibrate the MOX sensor reading and reduce drift due to humidity/temperature. Nice sensor, right? Therefore, Adafruit has made it easy for you to get started right away. STEMMA QT connectors on both sides are compatible with SparkFun.
Buy It Now
$35.32 Shipping Condition: Brand New Location: United Arab Emirates Digi xBee s1 Pro with explorer regulated
Buy It Now
$5.99 Shipping Condition: New Location: Upland, United States just the wedge, no cable.
|
|
|
|
Arduino Sparkfun Dangershield HACKED
Arduino Sparkfun Dangershield HACKED modified as shown in photos. not all functions work. please bid accordingly California residents will be charged California state sales tax. You may be interested in on eBay. Powered by
|
|
|
Lot of Sparkfun arcade buttons concave red green blue Microswitch
Lot of 28 Concave Arcade Buttons. 9 Red 9 Green 10 Blue Comes with Microswitch. So relieves worries on debouncing All the buttons function perfectly. And come with soldered wire lead attached. Equivalent to this product in Sparkfun: Description: This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button has a great tactile. clicky' feel. Features: Concave plunger design, Durable nylon material, Microswitch: max 3A@ 120 VAC, Microswitch reliability tested to 10.000,000 cycles, Includes 3 terminal microswitch, Net weight: 25g, Dimensions: Cap diameter: 35mm, Overall height: 65mm, Mounting hole: 1 1/8th inch paddle bit(1.125" 28mm)
|
|
|
SparkFun Inventor's Kit for Arduino with Retail Case (Revision 2 with 80 Page Bo
This product was only use a few times and remains in excellent condition. All of the components are included. This product has a 5 star rating on Amazon. ``d.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E%60%60d-13f6ce9c178-0xff-
|
|
|
Sparkfun Variable Temperature 50W Soldering Iron & Station
Unit includes 110V base station. Iron, iron holder, and brass sponge. The unit takes around 20 seconds to heat up. The station includes a brass sponge so you don't have to wet anything. Just wipe the tip across the brass sponge and you're good to go! The red LED on the front will be constantly on while the iron is heating up. Then the LED will start to pulse slowly(on for around three seconds. Off for around three seconds, repeat) This LED indicates that the iron has reached and is maintaining a constant temperature(also called a control loop or feedback loop) Features: Lead-free capable-Temperature adjustable from 220- 480 degrees C(428-896 degrees Fahrenheit) Includes 900M tip-50W iron Item was used only once and is still in fine working condition. Item was tested prior to this listing and will be tested once more once sold before ... moreshipping for quality assurance. Item will ship in its original box(with individual component boxes inside) and will be packed carefully to avoid damages in transit.
|
|
|
Sparkfun inventor's kit with Arduino Uno
This is the'retail' version of the SparkFun Inventor's Kit(SIK) This version comes with the carrying case seen in the pictures. Where the standard version does not. You can buy the case separately though if you wish. This kit has it all. It includes the Arduino Uno. The fabled baseplate, and all the sensors you can shake a stick at. This version includes a plastic carrying case to organize all the components. The SparkFun Inventor's Kit for Arduino is a box of goodies to get the very beginner started with programmable electronics. It includes all the bits you need to build 12 basic circuits, no soldering required! On top of that, we've joined forces with Oomlout to offer a small booklet to get you started. The SIK comes with everything pictured and a 36 page color printed'starter' guide. The guide will take a complete ... morenovice and get them: Blinking LEDs, Controlling a toy motor, Controlling a servo, Making(bad) music, Responding to buttons, Twisting a volume knob, Detecting ambient light, Reading temperature, Controlling big devices, Mixing LED colors, We believe these to be the building blocks of any electronics project. Once these concepts are mastered. Very impressive projects are possible using simple recombinations. Note: No soldering required. We recommend this kit for beginners ages 10 and up.
|
|
|
Sparkfun MP3 Player Shield for Arduino
This Item has been used about 5 times works great still and I will include a micro SD 2GB card with it.Description: This new revision of the MP3 player shield retains the awesome MP3 decoding abilities of the last version but adds the storage functionality of the SD card shield. Now you can pull MP3 files from an microSD card and play them using only one shield. Effectively turning any Arduino into a fully functional stand-alone MP3 player! The MP3 Shield still utilizes the VS1053B MP3 audio decoder IC to decode audio files. The VS1053 is also capable of decoding Ogg Vorbis/MP3/AAC/WMA/MIDI audio and encoding IMA ADPCM and user-loadable Ogg Vorbis.The VS1053 receives its input bitstream through a serial input bus(SPI) After the stream has been decoded by the IC, the audio is sent out to both a 3.5mm stereo headphone jack, as well as a 2-pin ... more0.1" pitch header.This shield comes populated with all components as shown in the images and schematic; but it does not come with headers installed. We recommend the 6 and 8-pin stackable headers.Features:3.5mm audio out jack0.1" spaced header for speaker outmicroSD card slot
|
|
|
Sparkfun Logomatic v2 Serial SD Datalogger with 1gb SD, Li-Ion Battery, More
This is a sparkfun Logomatic V2 datalogger. It was used for small project and then put away. Comes with 1gb Micro SD Card with adapter. 6600mAh Li-Ion battery, ACS712 Low Current Board. It all works well
|
|
|
3 stepper motors CNC Kit setup with sparkfun easy drivers NEMA 17
ROB-09238 Description: This is a simple. But very powerful stepper motor with a 4-wire cable attached. This is a Motor. Features: Step Angle(degrees) 1.8, 2 Phase, Rated Voltage: 12V, Rated Current: 0.33A, Holding Torque: 2.3kg*cm, 5mm Diameter Drive Shaft, Winding resistance: 32.6 Ω, Winding inductance: 48 mH, Max flux linkage: 1.8 Vs, Maximum Detent Torque: 0.016 N.M, Total inertia(kg.m.m) 3.5 Kg.m.m, Total friction(kg.m/s) 4 Kg.m/s, Three stepper motors with 3 easy driver motor drivers presoldered or easily removed ROB-10267 Description: The EasyDriver is a simple to use stepper motor driver. Compatible with anything that can output a digital 0 to 5V pulse(or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver) EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has ... morean on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. On this version(v4.4) we fixed the silk error on the min/max adjustment. This is the newest version of EasyDriver V4 co-designed with. It provides much more flexibility and control over your stepper motor. When compared to older versions. The microstep select(MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control. These three motors with the accompanying drivers are perfect for a DIY CNC machine or other such device. They are used but are fully working and show few signs of prior use.
|
|
|
5 sparkfun boards/ ardumoto/arduino.berlios
All have items soldered unto the boards. I have no idea what was being built
|
|
|
Barometric Pressure Sensor BMP085 board from Sparkfun for arduino and beaglebone
Works perfectly.
|
|
|
Sparkfun GE864 EVK v1 Telit GE864-QUAD
Sparkfun GE864 EVK v1 Telit GE864-QUAD Has been power recognize by the computer no further test has been made. Sold as is. See Pictures. What you see is what you get. CEL-09271 Replacement: None. There is no drop-in replacement for this part. But have a look at our cellular category for other modules and evaluation boards that may work in your application. This page is for reference only. Description: This is the SMD equivalent of the GM862. The GE864 module has all the quad-band functionality of the GM862 packed into a much smaller BGA machine placeable device. The low profile and small size of the unique BGA package for the GE864-QUAD enable the design of very compact applications. Since connectors are eliminated. The solution cost is significantly reduced compared to conventional mounting. With its ultra-compact design and extended temperature ... morerange. The Telit GE864 product line is the perfect platform for high-volume m2m applications and mobile data devices. Additional features such as integrated TCP/IP protocol stack and serial multiplexer extend functionality of the application at no additional cost. State-of-the-art ADC. DAC, GPIO, SPI and I2C interfaces provide connectivity to external peripherals such as sensors and displays. All Telit modules. Support Over-the-Air firmware update by means Premium FOTA Management. By embedding RedBend’s vCurrent® agent, a proven and battle-tested technology powering hundreds of millions of cellular handsets world-wide Telit is able to update its products by transmitting only a delta file, which represents the difference between one firmware version and another. This smaller SMD module requires an external SIM card socket and external Antenna Connection(50Ohm) This module interfaces through 3V CMOS logic levels. You must not use 5V levels. We recommend a simple voltage divider or equivalent logic level translation circuit. Features: GSM Quad-band, GPRS Class 10, Embedded TCP/IP, Full 99/5/CE Approvals, Extended Temperature Range, BGA Package, RoHS Compliant, Document
|
|
|
"ARDUINO" SPARKFUN INVENTOR'S KIT free relay module, RGB cathode, and sensor..
very good offer used 3X only. With free relay module
|
|
|
sparkfun Investor's Kit ( Plus Lots Of Components)
THE MUST COMPLE ARDUINO KIT ON EBAY THIS KIT IS COMPLETE FROM SPARKFUN. THE BOX KIT IS OPPEN BUT ALL THE COMPONENTS INSISDE ARE BRAND NEW(NEVER USED) I WILL LIST IT AS USED) I GOT IT AS A GIFT FOR MY KID WITH ALL THE EXTRA COMPONETS BUT HE DIDN’T LIKE IT. I OPENED THE BOX BUT I DIDN’T USE ANY OF THE COMPONENTS INSIDE SO EVERYTHING INSIDE THIS KIT IS BRAND NEW. I SPEND ABOUT $200 DOLLARS IN ALL OF THIS SO IM SPECTING TO GET SOME MONEY BACK. IF YOU ARE IN TO ARDUINO THIS IS YOUR CHANCE TO GET A COMPLETE KIT. ALL THE EXTRA COMPONENTS ARE BRAND NEW TOO AND THEY COME IN ITS ORIGINAL PACKAGE. HERE IS THE COMPLETE LIST OF ALL THE COMPONETS IN THIS KIT HAPPY BIDING Arduino Board Breadboard. User guide instructions. Sealed relay. Small servo. Yellow and red LEDs. Tricolored LED. Temperature Sensor. DC toy motor. 8 bit shift register. Push button switches. ... morePotentiometer. Miniature photocell. Transistors. Jumper wires. USB cable. Small signal diodes. 10K resistors. 330 ohm resistors. Buzzer. Flex Sensor. Soft potentiometer. Arduino/breadboard holder. Carrying case. I WILL INCLUDE THESE EXTRAS 16 x 2 LCD Display for Arduino Small Reduction Stepper Motor- 12VDC 32-Step 1/16 Gearing. PIR(motion) sensor Ultrasonic Sensor 3 RGB Led’s 433Mhz WL RF Transmitter + Receiver Module Link Kit for Arduino/ARM/MCU Wireless. 12 Key 4 x 4 Matrix Array Keyboard for Arduino/AVR/PIC Membrane Switch Keypad. 5V Voltage Regulator Board for Breadboard 9V to 12V Input. Battery Snap Connector Clip Adapter Plug w 2.1mm 9V. 9v Duracell Battery Relay board to be controlled with an arduino. HAPPY BIDING, YOU WILL GET EXACTLY WHAT YOU SEE IN THE PICTURE
|
|
|
SparkFun Pro Micro - 5V/16MHz DEV-12640 - ATmega32U4 Arduino compatible board!
Pre-soldered with header pins to pop right onto your breadboard! Guaranteed to be in full working order- I have run the Sparkfun test code on it and successfully with the Arduino IDE. That's all I've done with it(see below) As a novice Arduino hobbyist. I bought this 5v board and a bunch of 3.3v sensors and components. Thankfully I realized my mistake while researching how to wire up my components, but since I had already soldered the pins on to the board, I can't really return it to Sparkfun. I ordered a 3.3v board but now don't really have a project for this fellow. Features: ATmega32U4 running at 5V/16MHz Supported under Arduino IDE v1.0.1 On-Board micro-USB connector for programming 4 x 10-bit ADC pins 12 x Digital I/Os(5 are PWM capable) Rx and Tx Hardware Serial Connections Sparkfun's Smallest Arduino-Compatible ... moreBoard Yet! Full details. Datasheet, and other info can be found here: https:www.sparkfun.com/products/12640 Posted with
|
|
|
Two Bluetooth development boards from Sparkfun ("Purpletooth Jamboree" #11924)
Details: sparkfun.com product# 11924($65 per board) Purpletooth Jamboree" Bought two boards for a project. They both work fine. I can get them to talk to other Bluetooth devices and each other. I found there is an inherent delay of maybe 1/2 second in transmission of audio. My project could not tolerate that latency. So I need to sell them. On both boards I soldered on a 5 pin header to readily connect the serial cable(the Adafruit console cable works great for this) On one board I added a 4 X 2 header in the power supply section of the board(and realized I didn't need it after all)
|
|
|
Sparkfun 50W Analog Electronic Soldering Iron AT936B (Rebranded Atten 936) USED
Selling a used Sparkfun soldering iron. Iron still works perfectly fine. But the tip is oxidizing and needs to be replaced soon. The tip is a conical shape and is the one that originally came with the iron. Looks like a rebranded Atten 936B which is a clone of the Hakko 936. Comes in original box. Auction includes: 50W Iron Base Soldering iron with used tip Soldering Iron stand with sponge Specs: Lead-free capable Temperature adjustable from 220-480°C(428-896°F) 50W Iron US 120V Power Input
|
|
|
SparkFun Inventor's Kit for Arduino - V3.1
This kit is in perfect condition. And was barely used. There are a few additional items included that are not in the normal kit; like magnets and reed switches that I had purchased additionally for a project but never used. The kit alone is $99 new on Sparkfun's website. From Sparkfun's Website: The SparkFun Inventor’s Kit(SIK) is a great way to get started with programming and hardware interaction with the Arduino programming language. The SIK includes everything you need to complete 15 circuits that will teach you how to read sensors. Display information on an LCD, drive motors, and more. You don’t need any previous programming or electronics experience to use this kit. The full-color SIK Guidebook(included) contains step by step instructions of how to connect each circuit with the included parts. Full example code is provided and ... moreexplained and even includes troubleshooting tips if something goes wrong. The kit does not require any soldering and is recommended for beginners ages 10 and up. The new V3.1 version of the kit includes the SparkFun Mini Screwdriver to secure your RedBoard to its baseplate and replaces the translucent red breadboard with an opaque white breadboard(now you’ll be able to clearly see which socket you are inserting your hook-up wires into) Circuit Examples: Circuit 1: Blinking an LED, Circuit 2: Reading a Potentiometer, Circuit 3: Driving an RGB LED, Circuit 4: Driving Multiple LEDs, Circuit 5: Push Buttons, Circuit 6: Reading a Photo Resistor, Circuit 7: Reading a Temperature Sensor, Circuit 8: Driving a Servo Motor, Circuit 9: Using a Flex Sensor, Circuit 10: Reading a Soft Potentiometer, Circuit 11: Using a Buzzer, Circuit 12: Driving a Motor, Circuit 13: Using Relays, Circuit 14: Using a Shift Register, Circuit 15: Using an LCD, Kit includes: with headers) and Resistors,
|
|
|
SPARKFUN REDBOARD ARDUINO KIT & PROTOSCREWSHIELD, ARDUMOTO DRIVER LOTS OF EXTRAS
ARDUINO SPARKFUN KIT WITH MANY EXTRAS USED FOR ONE CLASS WHICH WAS DROPPED HALFWAY THROUGH COMES WITH A BUNCH OF ACCESSORIES. SENSORS, SHIELDS, DRIVERS, MICRO SERVO, IR SENSOR, USB CABLE, WALL WORT, JUMPER WIRES, SENSORS, EVERYTHING SHOWN IN PHOTS& SIK MANUAL WITH 15 EXPERIMENTS. $250+ RETAIL VALUE SHIPPING COST IS TO LOWER 48. AK, HI, OVERSEAS ACTUAL SHIPPING COST.
|
|
|
Sparkfun Inventor`s Kit, Complete w/ Case, Version 3. 1,Programmed with Arduino!
For auction a complete SparkFun Inventors Kit v3.1 programmed with Arduino. This kit is complete with all original parts. Rugged case, and instruction manual. In a addition i'm throwing in over $50 in various arduino accessories and sensors from Element14! Newark Part No. Qty Ordered Mftr. Part No Manufacturer/ Description 1, 10, 10, 10, 10, 5, 8, 5, 5, 5, 1, 1, 1, 1, 1, CAPACITOR ALUM ELEC 22UF. 16V, 20% RADIAL 1, CAPACITOR ALUM ELEC 0.1UF. 35V, 20% RADIAL 1, CAPACITOR CERAMIC. 1UF, 50V, Y5V, 20% RADIAL 2, BIPOLAR TRANSISTOR. NPN, 40V, TO-92 1,
|
|
|
Bundle - LCD 16x2 + SerLCD serial backpack - Sparkfun
This is a really good offer. A bundle including SparkFun parallel-based LCD 16x2(blue on white) AND SparkFun SerLCD backpack that enables you to control the LCD over a single-wire serial interface. These components are AS NEW. Used for a computer engineering senior design process successfully. I also include three jumper wires ☺ Mind you. The benefit of this bundle kit is that you can always unsolder the backpack, so you are actually purchasing TWO items, not one. The price at which I am listing the bundle is exceptionally low because I need to sell some stuff in order to buy grad school textbooks ☺ I also consider reasonable"best offers" because I want the component to be in your hands and become useful. Rather than sitting in my desk. Last but not least.shipping from the USA ☺ not from across the world.
|
|
|
Sparkfun Bluetooth Modem BlueSMiRF Silver RN42
Bought two pieces this summer; This one is used， but cleaned. ag6 2.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk.rp73%28c%3Eag6%3E2-14995430ec1-0x115-
|
|
|
Arduino SparkFun Inventor Kit plus Extras!!! ***Free Shipping***
The SparkFun Inventor’s Kit(SIK) is a great way to get started with programming and hardware interaction with the Arduino programming language. The SIK includes everything you need to complete 15 circuits that will teach you how to read sensors. Display information on an LCD, drive motors, and more. You don’t need any previous programming or electronics experience to use this kit. The full-color SIK Guidebook(included) contains step by step instructions of how to connect each circuit with the included parts. Full example code is provided and explained and even includes troubleshooting tips if something goes wrong. The kit does not require any soldering and is recommended for beginners ages 10 and up. The new V3.1 version of the kit includes the SparkFun Mini Screwdriver to secure your RedBoard to its baseplate and replaces the translucent ... morered breadboard with an opaque white breadboard(now you’ll be able to clearly see which socket you are inserting your hook-up wires into) Circuit Examples: Circuit 1: Blinking an LED Circuit 2: Reading a Potentiometer Circuit 3: Driving an RGB LED Circuit 4: Driving Multiple LEDs Circuit 5: Push Buttons Circuit 6: Reading a Photo Resistor Circuit 7: Reading a Temperature Sensor Circuit 8: Driving a Servo Motor Circuit 9: Using a Flex Sensor Circuit 10: Reading a Soft Potentiometer Circuit 11: Using a Buzzer Circuit 12: Driving a Motor Circuit 13: Using Relays Circuit 14: Using a Shift Register Circuit 15: Using an LCD Kit includes: Arduino Uno and breadboard holder SparkFun Inventor's Kit Guidebook Solderless breadboard Carrying case Sealed Relay Small Servo Yellow and red LEDs Tricolored LED Temperature sensor DC toy motor 8-bit shift register Push button switches Potentiometer Miniature photocell Transistors Jumper wires USB cable Break away headers Small signal diode 10k Ohm resistors 330 Ohm resistors Buzzer Flex sensor Soft potentiometer In addition to the SparkFun kit. This item also includes a 2 line monochrome LCD and an Arduino SD card/Real Time Clock shield to exte
|
|
|
Geek Ammo Sparkfun MicroView Arduino with built-in OLED Display
The MicroView is the first chip-sized Arduino compatible that lets you see what your Arduino is thinking using a built-in OLED display. This is the MicroView controller that I received from being a backer for the product on Kickstarter. This particular bundle went for $95 on Kickstarter. It has only been used once and everything is in very good condition. Includes all original accessories such as: MicroView, MicroView Programmer, Solderless Breadboaord, 74HC595 Shift Rergister, 2N2222 Transistors, 1N4148 Diodes, DC Motor with Gear, Small Servo, SPDT 5V Relay, TMO36 Temp Sensor, Softpot, USB Extension Cable, Jumper Wires, Photocell, Tri-color LED, Red and Yellow LEDs, 10K Trimpot, Piezo Buzzer, Big 12mm Buttons, 330 and 10K Resistors,
|
|
|
SparkFun Breadboard Power Supply Stick 5V/3.3V
Used. But still in great working condition. No rework done or switching of original components. Features: 6-12V input voltage via barrel jack or 2-pin header, 3.3V or 5V regulated output voltage, ON/OFF switch, Output voltage select switch, Power status LED, PTC fuse protected power, 5.5x2.1mm center positive barrel jack,
|
|
 |