|
|
Order by: Available to: eBay Affiliate Links
|
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New – Open box Location: Crescent City, United States Programmable motion controller for CNC etc
Buy It Now
Free Shipping Condition: New Location: China 8- The value of the inversion in place delay (i.e., the value of [P7]) in seconds. Feature: 1. This module has no programmable function, but built in ... morea variety of fixed operation mode, the user can quickly choose the appropriate trajectory.
Buy It Now
$3.50 Shipping Condition: New Location: China CNC Router Single 1 Axis Controller Stepper Motor Drivers TB6560 3A driver board, Photo: Description: Features: Working voltage DC 10V-35V. Recommended ... moreto use a switching power supply DC24V power supply. 6N137 high-speed optical coupling. Guarantee high speed without losing step. using the Toshiba TB6560AHQ new original chip with low voltage shutdown. Overheating stop and overcurrent protection circuit to ensure optimal performance. Rated maximum output: ± 3A. Peak 3.5A. for two-phase within 42.57 stepping 3A/ four-phase/ of line four/ six-wire stepper motor, and is not suitable for more than 3A stepper motor. automatic half current function. subdivision: whole step. Half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions. Dimensions: width 50* 75* long high-35(MM) Features similar products: 1. Current grade-by-adjustable to meet your demand for a variety of applications. 2. Semi-automatic flow adjustable. 3 6N137 high-speed optical coupling. Guarantee high speed without losing step. 4. Plate printed setup instructions operation without manual also. 5. Thick teeth radiator, good heat dissipation. Absolutely use Toshiba TB6560AHQ. New original chip, a penalty at ten! Package Contents 100% Brand New 1x TB6560 3A driver board, Shipping: We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback. So that we can satisfactorily address your concerns. It is impossible to address issues if we do not know about them! Ship by Post Air-mail within 1 working days after full payment is received. The shipment usually takes 12-35 business days to Worldwide. We also provide international Expressed delivery such as EMS. DHL and UPS,extra shipping fees is needed. The shipping time may vary. Depends on receiver's location. Country Delivery Time Working Days(not including holiday) 5-7 8-10 11-14 15-19 20-22 25 Working Days + Saturday + Sunday 5-9 10-14 15-20 21
Buy It Now
Free Shipping Condition: New Location: China Model Number: Driver Board. Motor Type: Driver Board.
Buy It Now
Free Shipping Condition: New Location: Springfield, United States
Buy It Now
$4.00 Shipping Condition: New Location: China 1 x USB Flash Drive.
Buy It Now
Free Shipping Condition: New Location: Hainesport, United States Product Specifications:4 Axis. --the chip internal resistance is smaller, lower heat, better heat dissipation. Support USB automatic identification. When ... moreplugged in USB and connected to the computer, it will automatically shield the offline interface to avoid offline interference with data.
Buy It Now
$9.80 Shipping Condition: New Location: Hoffman Estates, United States UCCNC Installation Video UCCNC software installation video. - Upto 400kHz operation. (selectable 25kHz, 50kHz, 100kHz, 200kHz, 400kHz with 20us, 10us, ... more5us, 2.5us and 1.25us pulse widths.). UC CNC software.
Buy It Now
Free Shipping Condition: New Location: Fontana, United States This motherboard is not compatible with Monport 40W Lightburn-ready CO2 Laser Engraver. Lightburn Compatible. This mother board is designed with cutting-edge ... morefeatures to create new possibilities to your 40W laser engraving machine.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States The Warp9 Ethernet Smooth Stepper (Turnkey System) - YouTube. 1-10ft Double Shielded CAT7 Ethernet Cable With Gold Plated Connectors For. 1-LPH 26-Pin ... moreto DB-25 Ribbon Cable With DB25 EMI Filter A nd Male DB25 Gender Changer To Attach To Your Breakout Board, G540, Or LeadShine Drive.
Buy It Now
Free Shipping Condition: New Location: United States 3 x23HS2430B Nema23 stepper motor (Dual Shaft) 112mm,425oz-in,2.8N.m,3.0A. The motor runs more quietly, with a high torque of 425oz in. rated current ... moreis 3A, allowing for a holding torque of 280Ncm(425oz. ).
Buy It Now
Free Shipping Condition: New Location: China 5，X/Y/Z/A four-axis drive, Y-axis dual drive, support rotary axis, stronger drive capability. 9，Support USB brush firmware, firmware upgrade is more convenient. ... more8，Reserved 24V, 12V, 5V power output port, which is convenient for expanding various functions.
Buy It Now
Free Shipping Condition: New Location: United States Side toggle switch EN: for the toggle switch, the white part is up and down, then down for the start; for the toggle switch, the white part is horizontal, ... morethen dial to start. The driver is based on advanced technology and be provided with high speed, high torque, low noise, low vibration, over current protection, overload protection, less phase line.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: China Eight currents and eight speeds can be seleted. It was widly used in the application of band carrier. Variable Speed Stepper Driver. Match for Nema 23, ... moreNema 24 and Nema 34 Stepper Motors. Cooling: Natural Cooling or Forced cooling.
Buy It Now
$3.99 Shipping Condition: New Location: China Axis: 1, 2, 3 or 4 (X, Y, Z, C). X, Y, Z, C axis can conduct linear interpolation, X, Y can do circular interpolation. Count: When this command is executed, ... morethe number on the main interface and manual interface will increase by 1 or decrease by 1.
Buy It Now
$18.00 Shipping Condition: New Location: Palatine, United States Description： Introduction: Compatible with most stepper drives and servo drives Simultaneously control 3 stepper motors With 24 programmable input interface. ... moreCan be configured to be"limit" E-stop" and other functions With 14 programmable output interface. Can work with water-cooling or mist-cooling spindle and other devices PWM/VSO（0-10V） spindle control mode USB interface. Support MACH3 software DCDC electrical isolation With maximum 200KHZ stepper motor pulse control output. Suitable for most machine system Dimensions：120*72*20mm Weight:180g Requirements of Computer: Basic Configuration： USB 2.0 CPU: 1GHz Memory: 512MB 500MB Available disk space Recommended configuration： USB 2.0 Memory: 2GB CPU: 2GHz Dual Core 1G Available disk space Product feature USB communication interface. And power supply for the board 10 IO input. Opto-isolated， It Can be configured to limit the emergency stop and other functions， all of them are 2edg port 14 IO input with no opto-isolated but with iso-IC. This port is set to IDC 2.54mm port 14 IO output with no opto-isolated but with iso-IC. This port is set to IDC 2.54mm port 2IO output with opto-isolated for spindle Up to 6 axes stepper-motor control port. Each port has up to 200KHz plus output COTEX-M3 of NXP-LPC is main control chip New design Aluminum shell make the system more stable This system is equipped with RS2332 manual control box. You can use manual control box with this port Spindle control port has PWM Mod（0%100% dutycycle with 12Vpp）and voltage Mod（0-10V） Spindle speed feed back port-INDEX There is a power autostability system. When USB port overvoltage or undervoltage or within other EMI. This system can make power of system stable There are High speed interface chips.Which make stepper driver signal more stable There is a USB protection chip,which can protect system within high voltage EMI Electrical parameters： Spindle Signal: 10V System input voltage: 5V Operating voltage of input interface with no opto-isolated: 5V Operating voltage of input interfa
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: United States Input: 1-5A Current, Select Drive Stepper Motor. ERR: Red Light, Power, Indicator Light, Power Indicator. Feature: 1. The half- function is a 200ms step ... morepulse, and the driver output current is automatically reduced to 50% of the rated output current to prevent motor heating.
Buy It Now
Free Shipping Condition: Used Location: Carpinteria, United States Welcome to have a look at my store. We offer a variety of different RC parts and RC tools that you may interest in. APM V2.8.0 ArduPilot UAV Flight Controller ... morewith Power Module& Mini OSD(CNC Case) for FPV Multicopter Airplane description: This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version. And change it into DF13-4P I2C external compass interface. Put DF13-5P GPS interface with external compass interface. Convenient for the connection of GPS and externalcompass. V2.52 I2C interface changes to multifunctional MUX interface- Modified version added isolation resistor. When the OSD interface used with telemetry, the interfaces is effectively avoided- V2.52 version 3.5V power supply adopts IPS79133. 6V withstand voltage, output current 100mA, need to supply power for six IC, slightly inadequate power supply ability, easy to be burnt dwon. The new version adopts US LP2985-3.3. 16V withstand voltage, more reliable, redcucing the possibility of Bad Gyro health Flight Controller- Needle: staight- Power supply: LP2985-3.3- Max voltage: 16V- Add a 47uF tantalum capacitor- Port: MUX(UART0. UART2, mnnI2 and OSD are optional, OSD is the defaulted output) Description: PM function: used for detecting battery voltage and current. Flight control board receives these two signals, calculating battery remaining power, and remaining flying time- This module has BEC function. Can output 5.3V DC, max 3A continuous current, supply stable power for flight control board- The signal cable connector adopts Japan original connector. Making the connection reliable- The APM 2.5 Power Module is a simple way of providing your APM 2.5 with clean power from a LiPo battery as well as current consumption and battery voltage measurements. All through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with Deans connectors. And wrapped in shrink tubing for protection. Description: APM Minim OSD V1.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States 12-3mm gold plated copper ring connectors.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China EMA342-7842S4 Nema34 Stepper Motor. This function is widely applied in RBI machine, Conveyor etc. Stepper motors and drivers from ENGMATE. ™ 5 Axis Kit ... morefor CNC DIY. 5 Axis Professional Breakout Board.
Buy It Now
Free Shipping Condition: New Location: Raleigh, United States The output is P17. The output is P1. 9, can be connected to the common negative or common driver, the input level is 5V driver.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Description: Industrial Mach3 CNC engraving machine controller was designed for Mach system Do not need to install any software and driver, Spring can ... morebe stretched to 3 meters Waterproof design, very durable, anti-dirt, oil spray Power by USB port Dimensions: 22 x 8 x 3cm Please note: this item works with Mach 3 ONLY The usb self-check light, you can type the " scroll" on the keyboard to activate it. Directional motion control: X+, X-, Y+, Y-, Z+, Z-, A+, A- Feed rate control: F+, F- Jog rate: J+, J- Spindle speed: speed up, slow down Programming: E-stop, cycle start, spindle on/off, Redo, single step, original point Package Include 1 * Remote controller 1 * Cable.
Buy It Now
Free Shipping Condition: New Location: China ● Y-axis dual drive, stronger drive capability;. ● XY limit switch interface each. ● One-piece integrated drive.
Buy It Now
Free Shipping Condition: New Location: 金东区, China Stepper motor: 42 stepper motor (1.3A/0.3Nm/24V). Stepper motor driver: A4988. 1 775 cable. XYZ limit:Support. The real color of the item may be slightly ... moredifferent from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
Buy It Now
Free Shipping Condition: New Location: United States The TB1H is a high performance microstepping driver based on the latest original TOSHIBA high-efficiency TB6600HG IC. The TB6600HG adopts single-chip ... morePWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency.
Buy It Now
Free Shipping Condition: New Location: China TMC2209 is compatible with many traditional drivers and TMC2208 pin. The advanced chopper can ensure noise-free operation of the motor, achieving high ... moreefficiency and motor torque. TMC2209 is an ultra-quiet motor driver IC for two-phase stepper motors.
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States Description: Industrial engraving machine controller was designed for system Do not need to install any software and driver, Spring can be stretched to ... more3 meters Waterproof design, very durable, anti-dirt, oil spray Power by USB port Dimensions: 22 x 8 x 3cm The usb self-check light, you can type the " scroll" on the keyboard to activate it. Directional motion control: X+,X-,Y+,Y-,Z+,Z-,A+,A- Feed rate control: F+,F- Jog rate: J+,J- Spindle speed: speed up, slow down Programming: E-stop,cycle start,spindle on/off,Redo,single step,original point Package Include 1 * Remote controller 1 * Cable.
Buy It Now
Free Shipping Condition: New Location: Katy, United States 新建网页 1 新建网页 1 新建网页 1 新建网页 1 新建网页 1 新建网页 1 新建网页 2?|a€“a°?￥&a circ;ao?§a?a€&ti lde;a?aμ 6 CNC Shield A4988 Driver Expansion Board for ... moreArduino V3 Engraver 3D Printer Description: 100% brand new and high quality This expansion board as a driver expansion board. Can be used for engraving machines, 3D printers. It is a total of four slots. Can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use. UNO for Arduino module IO port correspondence introduction. IO corresponding figure above UNO for Arduino- expansion board 8- EN( stepper motor driver enable. Active low) 7- Z.DIR(Z-axis direction control) 6- Y.DIR(Y-axis direction control) 5- X.DIR(X-axis direction control) 4- Z.STEP(Z-axis stepper control) 3- Y.STEP(Y-axis stepper control) 2- X.STEP(X-axis stepper control) The following is a simple stepper motor control procedures, define EN 8/ stepper motor enable. Active low# define X_DIR 5/ X-axis stepper motor direction control# define Y_DIR 6/ y-axis stepper motor direction control# define Z_DIR 7/ z axis stepper motor direction control# define X_STP 2/ x-axis stepper control# define Y_STP 3/ y-axis stepper control# define Z_STP 4/ z-axis stepper control/ Function: step. function: to control the direction of the stepper motor. The number of steps. Parameters: dir direction control. DirPin corresponding stepper motor DIR pin, stepperPin corresponding stepper motor" step" pin, Step number of step of no return value. void step(boolean dir. Byte dirPin, byte stepperPin, int steps) digitalWrite(dirPin. Dir) delay(50) for(int i = 0; i digitalWrite(stepperPin. HIGH) delayMicroseconds(800) digitalWrite(stepperPin. LOW) delayMicro
Buy It Now
Free Shipping Condition: New Location: China Subdivision selection range 1-128 subdivision.
Buy It Now
Free Shipping Condition: New – Open box Location: Ontario, United States
Buy It Now
$20.10 Shipping Condition: New Location: Bryan, United States Mach3 (demo). Nema 17 Stepper Motor Driver CNC Kit. Nema 17 stepper motor, Model 42BYGH404. Step Angle: 1.8 deg. Resistance per phase: 30 ohm. Holding ... moreTorque: 3.4 Kg-cm (47.2 oz-in).
Buy It Now
Free Shipping Condition: New Location: Monroe Township, United States UART mode: TMC2209 support UART mode. With UART mode you can set current, microstep easily via software. - Compared with TMC2100, the resistance of TMC2209 ... moreoutput driver (RDSon) is slightly lower, thereby reducing power consumption.
Buy It Now
Free Shipping Condition: New Location: China ✹✹ 【 Excellent Performance 】: DM556S Digital stepper motor driver, Using 32 -bit DSP technology, is suitable for driving 57 and 86 series motors, with ... moreexcellent mid -speed and low -speed performance.
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: United States Support for connecting electronic handwheel. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;. 4 general-purpose ... moreinputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
Buy It Now
Free Shipping Condition: New Location: China 1 x 4-Axis TB6560 Stepper Motor Driver Kit. - Universal architecture: Supports most parallel software MACH3, KCAM4, EMC2 etc! - Adjustable drive current ... moresettings for each axis: 25%,50%,75%,100% of full current can be set for different stepper motors.
Buy It Now
Free Shipping Condition: New Location: Denver, United States This high subdivision driver is suitable for high subdivision motor. Suitable for stepper motor: 57,60,86 type 2-phase (4-wire, 6-wire, 8-wire). Output ... morePeak Current: 1.4~5.6A. Anti-Resonance for optimal torque, extra smooth motion, low motor heating and noise.
Buy It Now
Free Shipping Condition: New Location: Chino, United States Description: Industrial Mach3 CNC engraving machine controller was designed for Mach system Do not need to install any software and driver, Spring can ... morebe stretched to 3 meters Waterproof design, very durable, anti-dirt, oil spray Power by USB port Dimensions: 22 x 8 x 3cm Please note: this item works with Mach 3 ONLY The usb self-check light, you can type the " scroll" on the keyboard to activate it. Directional motion control: X+, X-, Y+, Y-, Z+, Z-, A+, A- Feed rate control: F+, F- Jog rate: J+, J- Spindle speed: speed up, slow down Programming: E-stop, cycle start, spindle on/off, Redo, single step, original point Package Include 1 * Remote controller 1 * Cable.
Buy It Now
Free Shipping Condition: New Location: United States Users can set microstep within 25600 and multi-range current value within rated current. Built-in microstep technolog greatly improves stability and reduces ... morenoise under low microstep. 2-256 microstep setting range.
Buy It Now
Free Shipping Condition: New Location: United States Cnc Router 5 Axis Breakout Board For Microstep Controller& 0-10V Analog Output More. The latest upgraded 5 axis breakout board is specially designed ... morefor the CNC single axis 2-phase stepper driver controller. The breakout board using high-performance three-state bus driver 74HC244 and Schmitt inverter 74HC14. amplified. The input signal is amplified, rectified, filtered to make the drive capability of the output signal more stable and stronger. With this 5 axis breakout board, any 1-5 Microstepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. parallel-control CNC software. High performance. Cost-effective. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3. Linux CNC(EMC2) etc. parallel-control CNC software. USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security. 5-input interface to define the Limit. Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V. And with anti-reverse function. One relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc. Compatible with all the 2 phase microstep drivers in the market. Output 0-10V analog voltage for inverter to control the spindle speed. Shape Pulse and direction signals. Data transfer speeds of up to 10MBit/S. Amplification. Filtering, enhancement processing drivers enable signal. Suitable for a wide range of 2-phase microstep drivers in the market. Such as M542. M542H, MA860H, 2MA2278, 2M542, 2M860 etc. For advising. Such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc.It can be used in various kinds of machines, such as X-Y tables, labeling machines, laser cutters, engraving machines, pick-place devices, and so on. This breakout board is just a interface board. NOT a stepper driver board, it must work together with the microstep drivers(eg. MA860H etc. to control
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States This system is built around the Gecko Drive G540 digital integrated micro stepping 4 axes driver system. I also include the required resistors for the ... moreG540. Gecko G251x Driver Myths.16ft Table Run With Gecko G540 Drivers.
Buy It Now
Free Shipping Condition: New Location: Milner, United States This is a benefit because this is also the version that fits nicely on a breadboard leaving space on the sides - but be aware that V3 boards will not ... moremate with the female headers on this board. Motor Driver Board with built-in L293D chip.
Buy It Now
Free Shipping Condition: New Location: Oakland, United States Adapted to Nema17, Nema23 and Nema34 stepper motors. The maximum subdivision is 128 subdivision, more accurate.
Buy It Now
Free Shipping Condition: New – Open box Location: San Antonio, United States ITEM DOES NOT INCLUDE WIRES OR BUTTONS. and wires.
Buy It Now
$8.60 Shipping Condition: Used Location: Gilbert, United States Introducing the SainSmart CNC Micro-Stepping Stepper Motor Driver ST-M5045. This top-of-the-line product is designed for professionals and hobbyists alike ... morewho are in need of a reliable and efficient motor driver for their CNC machines. With its advanced micro-stepping technology, it ensures smooth and precise movements of your stepper motor, resulting in higher accuracy and better quality of your work. This product is perfect for those in the industrial automation and motion control industry, as well as for businesses and individuals who are looking for a high-quality stepper motor driver. It is compatible with STM brand motors and the ST-M5045 model, making it easy to install and use.
Buy It Now
$18.59 Shipping Condition: Used Location: Merced, United States 3,000,000 pulses/sec. We can’t do it all. Outputs: TTL (0-5Volts) Power +5V: 0.75 Typical 1.0 Max. OEM and Compatible products. TECHNICAL SPECIFICATIONS.
Buy It Now
$3.00 Shipping Condition: New Location: China THIS is a 3-axis Mach3 USB interface board (NPN) worked with Mach3. - 16 general digital input points, corresponding to 16 LED indicators. - Support all ... moreversions of Mach3. Supports all versions (32-bit/64-bit).
Buy It Now
$9.00 Shipping Condition: New Location: United States Q1:why other supplier's TB6560 driver has 3.5A/3A current,but yours is 2.5A?. Supports a lot of stepper motors. 4-wire 0-3.5A normally 3A, the 3.5A is ... morethe peak currentcan be regulated rate current output, bipolar stepper motor driver.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States It connects to your G540's DB25 connector, or CNC breakout board's DB25 connector, and adds the ultimate in EMI filtration for the.
Buy It Now
$2.00 Shipping Condition: New Location: China Suitable for two phase/four phase/four wire/six wire stepper motors within 42,57 step 4A. Rated output current: 3A. Adopts thick and dense tooth radiator, ... moregood heat dissipation. Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
Buy It Now
$3.00 Shipping Condition: New Location: China Maximum 2000KHZ pulse output for each axis, supporting stepper motors and servo motors. - 4-channel differential signal output: pulse + direction. Usually ... moreit cost about 35USD-50USD.
Buy It Now
Free Shipping Condition: New Location: Spring Hill, United States
Buy It Now
$80.00 Shipping Condition: New Location: China Support servo driver alarm and inverter alarm etc. For CNC Linear Automatic Tool Change Machine. Advanced functions such as tool broken continue carving, ... morearray work, part work, find break number, power failure protect (get details from the user's manual).
Buy It Now
Free Shipping Condition: New Location: Fontana, United States Firmware: GRBL. This mother board is designed with cutting-edge features to create new possibilities to your 40W laser engraving machine. Compatible Software: ... moreLightBurn (Windows/Linux/MacOS). This motherboard is compatible withregular K40/ K40 with ribbon cable, which is not support lightburn function before.
Buy It Now
Free Shipping Condition: New Location: China
Buy It Now
Free Shipping Condition: New Location: United States 4.0A phase current. Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning ... moreaccuracy is also higher. 3 PCS Nema 23 Stepper Motor dual shaft with 428oz-in holding torque.
Buy It Now
Free Shipping Condition: New Location: Hong Kong SAR China The Latest 3rd Generation Revolutionary & Professional TB6560 3 Axis Stepper Driver Box Set (TB3CD-P (Box)). Actually, the 3rd generation TB6560 Stepper ... moreDrivers have two types of versions, one is thestandard version, and another is theprofessional version.
|
|
|
 |