|
Order by:
Available to:
eBay Affiliate Links
|
Buy It Now
$2.99 Shipping Condition: New Location: China The input signal can be either a single-ended signal or a differential signal. Two-Channel Matched Logarithmic Amplifier with Integrated Phase Detector. ... moreThe exact typical value is less than 1 degree.
Buy It Now
$2.99 Shipping Condition: New Location: China The input signal can be either a single-ended signal or a differential signal. Two-Channel Matched Logarithmic Amplifier with Integrated Phase Detector. ... moreThe exact typical value is less than 1 degree.
Buy It Now
$3.00 Shipping Condition: New Location: China DC12V-24V TPA3118 Mono Channel BTL 50W Balanced Unbalanced Input Amplifier Board. Balanced Input Signal (differential): Signal + Signal -, GND (ground). ... moreSignal Input Mode Output Power:50W (2Ω speaker). ).
Buy It Now
$45.00 Shipping Condition: New Location: 南山区, China The integrated DPSK receiver module IDRV consists of a balanced photoreceiver and an integrated delay-line interferometer (DLI). The IDRV is a differential ... morefront-end for 43 Gbit/s DPSK-applications featuring high differential gain of typically 1500 V/W. The two output ports of a phase-tunable DLI are coupled into two single chip waveguide-integrated pin-photodiodes (PD). Signal gain is obtained using a differential amplifi er with limiting output stage. The limiting amplifi er produces a typical differential output voltage swing of 550 mV. .
Buy It Now
$43.74 Shipping Condition: Used Location: Farmingdale, United States TEK P7313 with complete accessories in carrying case. Mint condition. Good luck! DESCRIPTION 12.5 GHz Z-Active(TM) Differential Probe for use in applications ... moresuch as PCI-Express I& II. Serial ATA II, USB 2.0, DDRII, Rambus, XAUI, etc. The Z-Active architecture is a hybrid approach composed of a distributed attenuator topology feeding an active probe amplifier. The Z-Active probes use a tiny passive probe tip element that is separate from the amplifier, extending the usable reach of the probe. In traditional active probes, adding this much length can introduce signal fidelity problems. However this architecture maintains high DC input resistance and presents a higher AC impedance than previous probe architectures. It accomplishes this while providing significant length between the probe body and the probe attachment point to the DUT. This architecture provides the best of both worlds: high DC impedance like existing active probes and the stable high frequency loading of Z0 probes. Signal Fidelity Z-Active architecture provides: High bandwidth Excellent step response Low loading High CMRR Connectivity This family of probes uses Tip-Clip(TM) assemblies. An interchangeable probe tip system that enables customers to configure their probe with the optimal tip for their application. These detachable assemblies make it possible to replace a tip for a fraction of the cost formerly associated with such hardware changes. The several lengths and variable spacing of the assemblies provide flexibility for adapting to vias and other test points of differing sizes. With Tektronix Tip-Clip assemblies, Monday?s solder-in probe can become Tuesday?s handheld tool, simply by switching tips. The Z-Active probe design allows the probe to easily switch between solder, handheld, or fixtured applications.
Buy It Now
$30.74 Shipping Condition: Used Location: Farmingdale, United States The P7380SMA probe has two selectable attenuator settings that provide a tradeoff between dynamic range and noise. The P7380SMA probe has been optimized ... morefor a clean pulse response for accurate SDA compliance testing.
Buy It Now
$43.74 Shipping Condition: Used Location: Farmingdale, United States Model: P7380A. The P7380A is a Differential Probe from Tektronix. A differential probe is an active probe that has two inputs. A negative and positive ... moreinput along with a ground lead that drives a 50 Ohm cable to transmit the output ot a digital oscilloscope channel.
Buy It Now
$43.74 Shipping Condition: Used Location: Farmingdale, United States Model: E2695A. The E2695A is an accessory probe head that plugs into the InfiniiMax 1130 series of probe amplifiers to allow differential SMA connections ... moreto a single channel of the oscilloscope. Differential SMA Probe Head for InfiniiMax probes.
Buy It Now
Condition: Used Location: Chicago, United States EG&G PARC Model 124A L ock-In amplifier w/ 116 differential pre amp module installed;. This is an older legacy electronics unit, & as such it is being ... moresold "as is". When removed from service it was FULLY OPERATIONAL, but- it MUST be understood that it is legacy electronics & thus It is NOT represented to function as a modern, state of the art lock in amplifier.
Buy It Now
Condition: Used Location: Chicago, United States EG&G PARC Model 124A L ock-In amplifier w/ 117 differential pre amp module installed;PRISTINE. This is an older legacy electronics unit, & as such it ... moreis being sold "as is". When removed from service it was FULLY OPERATIONAL, but- it MUST be understood that it is legacy electronics & thus It is NOT represented to function as a modern, state of the art lock in amplifier.
Buy It Now
$41.35 Shipping Condition: For parts or not working Location: Canada
Buy It Now
$3.00 Shipping Condition: New Location: China DC12V-24V TPA3118 Mono Channel BTL 50W Balanced Unbalanced Input Amplifier Board. Balanced Input Signal (differential): Signal + Signal -, GND (ground). ... moreSignal Input Mode Output Power:50W (2Ω speaker). ).
Buy It Now
$2.88 Shipping Condition: New Location: China DC12V-24V TPA3118 Mono Channel BTL 50W Balanced Unbalanced Input Amplifier Board. Balanced Input Signal (differential): Signal + Signal -, GND (ground). ... moreSignal Input Mode Output Power:50W (2Ω speaker). ).
|
|
|